Miele PG 8061 User manual

Installation Plan


Professional Dishwasher
PG 8061
Mat. no.: 09 838 370
en - US

page 1/ 8Installation plan PG 8061
Installation instruction
Observe installation instructions when installing machine.
This dishwasher is only suitable for commercial use.
Installation
Installation should only be carried out by authorized installers in
accordance with valid regulations, relevant standards and health and
safety codes!
Condensate
Only use commercial grade cabinetry in the vicinity of this commercial
dishwasher as condensate may otherwise cause damage.
Machine feet
To ensure stability install the included floor bracket BBF-80 (Installation
Instructions Mat.no.: 09788890)
Electrical
connection
It is recommended to make electrical connection via a plug and socket
so that electrical safety checks can be carried out easily. The socket
must be accessible after machine installation.
With a fixed installation, this must be via a main switch to be provided
on site, which must completely isolate the machine from the power
supply with a contact gap of at least 1/8’’ (3 mm).
If necessary, an equipotential bond with good contact connection must
be provided in accordance with all appropriate national and local
regulations.
Protection class IP21
Non-return device
Connection to a drinking water supply is permitted without
an additional non-return device.
Steam condensor
Steam condensor (DK) requires its own cold water connection. Use the
supplied Y-adapter if only one cold water connection is available.
External dosing
system (optional)
Connect up to two dosing systems at the rear panel for liquid cleaning
agent and rinse aid.

Installation plan PG 8061 page 2/ 8
Dimensions in drawings in inches & [mm]

page 3/ 8Installation plan PG 8061
Dimensions in drawings in inches & [mm]
EL Electrical connection WW Hot water
KW Cold water AW Drain water
DS External dosing connection (optional) DK Steam condensor

Installation plan PG 8061 page 4/ 8
Electrical connection (208 V)
Voltage (default) 3 AC 208V 60 Hz 3 AC 208V 60 Hz
Rated load 5.8 kW 5.8 kW
Fuse rating 3 × 20 A 3 × 20 A
Minimum cross-section 4 × AWG 12 4 × 3.3 mm²
Length of electrical cord (UL 921) with plug approx. 6‘ 2“ approx. 1.9 m
Electrical connection NEMA L15-20 NEMA L15-20
Voltage (convertible) 2 AC 208V 60 Hz 2 AC 208V 60 Hz
Rated load 5.8 kW 5.8 kW
Fuse rating 2 × 30 A 2 × 30 A
Minimum cross-section 3 × AWG 10 3 × 5.2 mm²
Length of electrical cord (UL 921) with plug approx. 6‘ 2“ approx. 1.9 m
Electrical connection NEMA L6-30 NEMA L6-30
Electrical connection (240 V)
Voltage (default) 3 AC 240V 60 Hz 3 AC 240V 60 Hz
Rated load 5.8 kW 5.8 kW
Fuse rating 3 × 20 A 3 × 20 A
Minimum cross-section 4 × AWG 12 4 × 3.3 mm²
Length of electrical cord (UL 921) with plug approx. 6‘ 2“ approx. 1.9 m
Electrical connection NEMA L15-20 NEMA L15-20
Voltage (convertible) 2 AC 240V 60 Hz 2 AC 240V 60 Hz
Rated load 5.8 kW 5.8 kW
Fuse rating 2 × 30 A 2 × 30 A
Minimum cross-section 3 × AWG 10 3 × 5.2 mm²
Length of electrical cord (UL 921) with plug approx. 6‘ 2“ approx. 1.9 m
Electrical connection NEMA L6-30 NEMA L6-30
Cold water connections*
Max. temperature 68 °F 20 °C
Max. water hardness 70 gpg 70 °d
Min. flow pressure 29 psi 200 kPa
Min. flow pressure with extended water intake 5.8 psi 40 kPa
Max. pressure 145 psi 1,000 kPa
Throughput 2 gal/min 7.5 l/min
Connection thread - on site (flat sealing) 3/4“ Male Garden Hose
Thread
3/4“ Male Garden
Hose Thread
(USA: 11.5 NH)
Length of connection hose (supplied) approx. 5‘ 7“ approx. 1.7 m
Length of the steam condensor hose approx. 5‘ 7“ approx. 1.7 m
* Two cold water connections required: use supplied Y-adapter if only one cold water connection is available.

page 5/ 8Installation plan PG 8061
Hot water connection
Max. temperature 150 °F 65 °C
Max. water hardness 73 gpg 70 °dH
Min. flow pressure 29 psi 200 kPa
Min. flow pressure with extended water intake 5.8 psi 40 kPa
Max. pressure 145 psi 1,000 kPa
Throughput 2 gal/min 7.5 l/min
Connection thread - on site (flat sealing) 3/4“ Male Garden Hose
Thread
3/4“ Male Garden
Hose Thread
(USA: 11.5 NH)
Length of connection hose (supplied) approx. 5‘ 7“ approx. 1.7 m
Drain water
Drain hose (internal diameter x wall thickness) 7/8” × 1/4” 22 × 6 mm
Length of Commercial Dishwasher drain hose 4’ 11” approx. 1.5 m
Drain pump head height from floor level, max. 3’ 3” 1 m
Drain hose delivery, max. 4.2 gal/min 16 l/min
On-site hose connector (external diameter x length) 7/8” × 1 3/16” 22 × 30 mm
External dosing system (optional)
Connect up to 2 dosing systems at the rear panel for liquid cleaning agent and rinse aid.
Machine feet
Height adjustable 0 - 2 3/8“ 0 - 60 mm
Foot diameter 1 3/8“ 35 mm
Entry point into housing 8 M 8 M
Heat dissipation to room
Heat transfer by emission 1194 btu/h 0.35 kWh/h
Load on removal 1365 btu/h 0.40 kWh/h

Installation plan PG 8061 page 6/ 8
Machine data
Unit height 32 5/16“ 820 mm
Height including cover 32 7/8“ 835 mm
Width 23 9/16“ 598 mm
Depth 23 7/16“ 595 mm
Door height 26 9/16“ 675 mm
Net weight 154 lbs 70 kg
Dynamic floor load 1.200 N 1.200 N
Width including transport pallet 26 3/8“ 670 mm
Depth including transport pallet 29 1/8“ 740 mm
Height including transport pallet 36 1/4“ 920 mm
Set-up conditions
Ambient temperature 40-105 °F 5-40 °C
Max. humidity 80% 80%
Max. altitude above sea level 6560‘ 2.000 m

page 7/ 8Installation plan PG 8061
U.S.A.
Miele, Inc.
National Headquarters
9 Independence Way
Princton, NJ 08540
Phone: [phone]
Fax: [phone]
www.mieleusa.com
Technical Service & Support
Nationwide
Phone: [phone]
Fax: [phone]
[email protected]
All rights reserved! Date: 2015-06-08 Mat. no.: 09 838 370