Miele KM 404 User manual

Installation instructions
Gas-hob
KM 404 / KM 405
KM 406
KM 414 / KM 417
It is essential to read these
instructions before installing
or using the machine, to avoid
the risk of accident or
damage to the machine.
WO
M.-Nr. 05 021 252

Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Building in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Appliance dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
KM 404. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
KM 405. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
KM 406. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
KM 414. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
KM 417. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Safety clearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
KM 404 / KM 405 / KM 406 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
KM 414 / KM 417 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Worktop cut-out for KM 404 / KM 405 / KM 406. . . . . . . . . . . . . . . . . . . . . . . . . 13
Installation KM 404 / KM 405 / KM 406 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Fitting the spacer bars and support brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Fixing the spacer bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Granite worktops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Fixing the support brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Granite worktops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Building in the gas hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Worktop cut-out KM 4 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installation KM 4 4 / KM 4 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Fitting the spacer bars and support brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Fixing the spacer bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Fixing the support brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Granite worktops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Building in the gas hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Contents
2

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Gas connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Natural gas / liquid gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Conversion to another type of gas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
KM 404. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Jet table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Changing the jets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
KM 405. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Jet table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Changing the jets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
KM 406. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Jet table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Changing the jets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Check the first intake of air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
KM 414 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Jet table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Changing the jets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
KM 417. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Jet table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Changing the jets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Contents
3

Building in
Fit wall units and the cooker hood
before fitting the appliance, to avoid
damaging it.
As a minimum 20 m3space is
required where the appliance is
installed, and a door or window which
can be opened to the outside air.
The veneer or laminate coatings of
worktops (or adjacent kitchen
units) must be treated with 100 °C heat
resistant adhesive which will not
dissolve or distort.
The worktop upstand must be heat
resistant.
Ideally the hobs should be installed
with plenty of space on either side.
There may by a wall at the rear and a
wall or tall units at one side. On the
other side, however, no unit or divider
should stand higher than the hob.
Due to the heat radiated by the hob
and to allow cooking fumes to
dissipate it is essential that a
minimum safety distance ais
maintained between the worktop
cut-out and adjacent kitchen units,
e.g. a tall unit, as follows:
00 mm with KM 404 / KM 405
250 mm with KM 406
200 mm with KM 4 4 / KM 4 7
There must be a minimum safety
distance of 50 mm between the
appliance and a back wall.
recommended
not recommended
not allowed
Warning and Safety instructions
4

The gas hob must not be installed
next to an electric fryer, as the gas
flames could ignite fat in the fryer. It is
essential to maintain a minimum
distance of 288 mm between these two
appliances.
A hob may not be built in over a
washing machine, tumble dryer,
dishwasher, fridge, fridge-freezer or
freezer. The high radiant temperatures
which are sometimes generated by the
hob could damage such appliances.
This equipment is not designed for
maritime use or for use in mobile
installations such as caravans, aircraft
etc. However it may be suitable for
such usage subject to a risk
assessment of the installation being
carried out by a suitably qualified
engineer.
Safety distance above appliances
A minimum safety distance bmust be
maintained between the hob and the
cooker hood above it. See the
manufacturer’s operating and
installation instructions for details. For
any flammable objects, e.g utensil rails,
wall units etc. a minimum safety
distance of at least 760 mm should be
maintained between it and the hob
below.
When two or more appliances are
installed together below a cooker
hood, e.g. a ceramic combiset and
a gas wok combiset, which have
different safety distances given in
their installation instructions you
should select the greater distance of
the two.
All dimensions in this instruction booklet
are given in mm.
Keep these instructions in a safe place
and pass them on to any future owner
of the appliance.
Warning and Safety instructions
5

KM 404
aSupport bracket
bBuilding in height plus 3 mm for fixing screw
Appliance dimensions
6

KM 405
aSupport bracket
bBuilding in height plus 3 mm for fixing screw
cFront
dBuilding in height - Mains connection box
eGas connection
Appliance dimensions
7
55
8
514
288
500
min.50
max.R4
d
b
266
a
c
d
cb
8
514
288
e
55
58
30
48
72
25

KM 406
aSupport bracket
bBuilding in height plus 3 mm for fixing screw
Appliance dimensions
8

KM 4 4
aSupport bracket
bBuilding in height plus 3 mm for fixing screw
Appliance dimensions
9

KM 4 7
aSupport bracket
bBuilding in height plus 3 mm for fixing screw
cFront
dBuilding in height - Mains connection box
eGas connection
Appliance dimensions
10
552-560
55
8
514
574
500
min.50
max.R4
b
c
d
aa
d
cb
8
514
256
574
e
55
58
48
72
28

Before installing the appliance check that the location provides the required
clearances from combustible materials and if necessary provide protection to
adjacent surfaces as required by regulations.
Shown area indicates protected surface, which may be ceramic tiles or other
approved material.
If clearance between side and rear walls and the periphery of the burner is less
than 200 mm, the walls must be protected with a non-combustible material. The
protection must be extended a minimum distance of 150 mm above the burner
(refer - gas fitting regulations).
KM 404 / KM 405 / KM 406
KM 4 4 / KM 4 7
Safety clearance
11

Clearance above and around
the appliance
aRange hood
bnot less than 650 mm from burner to
any horizontal surface over full width
of the appliance.
cBurner
d10 mm recommended minimum
eCombustible work bench
fRegulator (NG)
gtest nipple of regulator 7 mm diam.
Safety clearance
12

Dimensions 7 mm and 11 mm are the
space taken up by the frame of the
appliance on the worktop.
^Make a cut-out for the hob in the
worktop, paying attention to the
appliance height. See section
"Appliance dimensions".
Dimension "B" applies to a combination
of appliances and is shown on the
chart.
There must be a minimum safety
distance of 50 mm between the hob
and the back wall and 100 mm
distance from a side wall to the right or
left of the hob (250 mm with KM 406).
See also chapter "Warning and Safety
instructions".
^Seal the cut surfaces with a suitable
sealant to avoid swelling caused by
moisture.
The materials used must be heat
resistant.
Installing one or more appliances
Cut out the worktop according to the
dimensions listed in the following chart.
Number
of
appliances
Worktop cut-out
Depth in
mm
± mm
Width
(= Dim. B)
in mm
± mm
1 500 266 mm
2 500 554 mm
3 500 842 mm
4 500 1130 mm
5 500 1418 mm
6 500 1706 mm
7 500 1994 mm
Important:
The maximum tolerance for the worktop
cut-out must not exceed ± 1 mm.
When building in several combiset
appliances a spacer bar must be
fitted between each unit.
See chapter "Fitting the spacer bars
and support brackets".
Worktop cut-out for KM 404 / KM 405 / KM 406
13

Fitting the spacer bars and
support brackets
aSupport brackets
bSpacer bars
The illustration above shows an
example of a worktop cut-out with
spacer bars band support brackets a
for 3 appliances.
For more than 3 appliances, repeat
dimension 288 mm.
The worktop cut-out dimensions for
several appliances are shown in the
table on the previous page.
cGap between spacer bar and
worktop.
dDrilling for a granite worktop.
^Fix the spacer bars band the
support brackets asupplied to the
positions indicated. See chapter
"Fixing the spacer bars" and "Fixing
the support brackets".
For the installation of electric
appliances see respective
installation instructions.
Installation KM 404 / KM 405 / KM 406
14

Fixing the spacer bar
^Position the spacer bars bin the
positions shown in "Fitting the spacer
bars and support brackets" so they
are flush with the top edge of the
cut-out, and secure with the 3.5 x 25
mm screws supplied.
^Then fill in gap cbetween the bars
and the worktop with silicone from
the tube supplied.
Granite worktops
^With granite worktops the spacer
bars bmust be positioned and
secured with strong double-sided
adhesive tape. In addition, coat the
edges with silicone and fill in gap c.
The screws are not required for granite
worktops.
Installation KM 404 / KM 405 / KM 406
15
c
d

Fixing the support brackets
^Position the two support brackets
supplied ain the positions shown in
"Fitting the spacer bars and support
brackets" so that they are flush with
the top edge of the cut-out, and
secure with the 3.5 x 25 mm screws
supplied. 2 screws are needed to
secure each support bracket.
The thickness of the worktop will
determine which drilled hole is used.
Please note that height of the
support bracket for the KM 406 is
different to that for the KM 404 and
KM 405.
Granite worktops
On a granite worktop a hole must be
drilled dat the position indicated to
secure each support bracket.
^Using a piece of strong, double-
sided adhesive tape position the
support brackets supplied aat the
positions indicated flush with the top
edge of the worktop and secure each
bracket with one screw in hole das
shown.
Building in the gas hob
^Lay the gas hob in the prepared
cut-out.
^Draw the electricity connection cable
through the cut-out and connect.
^Make the gas connection (see
chapter "gas connection").
^Secure the gas hob from below
through the middle elongated hole b
in each support bracket using the
two screws supplied. Carefully adjust
the hob if necessary.
Installation KM 404 / KM 405 / KM 406
16

Dimensions 7 mm and 11 mm are the
space taken up by the frame of the
appliance on the worktop.
^Make a cut-out for the hob in the
worktop.
Dimension "B" applies to a combination
of appliances and is shown on the
chart.
There must be a minimum safety
distance of 50 mm between the hob
and the back wall and 200 mm
distance from a side wall to the right or
left of the hob.
See also chapter "Warning and safety
instructions".
^Seal the cut surfaces with a suitable
sealant to avoid swelling caused by
moisture.
The materials used must be heat
resistant.
Worktop cut-out KM 4 4 / KM 4 7
Depth in mm
± mm
Width (= Dim B)
in mm
± mm
1 Hob 500 552-560
Worktop cut-out KM 4 4 / KM 4 7 +
288 mm wide appliances
Number
of
appliances
Depth
in mm
± mm
Width
(= Dim B)
in mm
± mm
KM 414 / 417 +1
KM 414 / 417 + 2
KM 414 / 417 + 3
KM 414 / 417 + 4
500
500
500
500
840
1128
1416
1704
Important:
The maximum tolerance for the worktop
cut-out must not exceed ±1 mm.
When building in several combiset
appliances a spacer bar must be
fitted between each unit.
See chapter "Fitting spacer bars and
support brackets".
Narrow combiset appliances (288 mm
wide) can be installed to the left or right
hand side of the KM 414 / KM 417.
Worktop cut-out KM 4 4
17

Fitting the spacer bars and
support brackets
KM 414 / KM 417with 2 appliances 288 mm wide bSupport brackets
aSupport brackets
bSpacer bars
Installation of several appliances
The illustration above shows an
example of a worktop cut-out with
spacer bars band support brackets a
for 3 appliances.
For more than 3 appliances, repeat
dimension 288 mm.
The worktop cut-out dimensions for
several appliances are shown in the
table on the previous page.
cGap between spacer bar and
worktop.
dDrilling for a granite worktop.
^Fix the spacer bars band the
support brackets asupplied to the
positions indicated. See chapter
"Fixing the spacer bars" and "Fixing
the support brackets".
For the installation of electric
appliances see respective
installation instructions.
Installation KM 4 4 / KM 4 7
18
500
563
KM 4 4
KM 4 7
288 277
1128
c
c
133
431
276 288
b
b
d
d
e
e
d
db
e
e

Fixing the spacer bar
The spacer bar is only required when
combined with a 288 mm wide
combiset appliance.
^Position the spacer bars bin the
positions shown in "Fitting the spacer
bars and support brackets" so they
are flush with the top edge of the
cut-out and secure using the
3.5 x 25 mm screws supplied.
^Then fill in the gap cbetween the
bars and the worktop with silicone
from the tube supplied.
Granite worktops
With granite worktops the spacer bars
bmust be positioned and secured with
strong double-sided adhesive tape. In
addition, coat the edges with silicone
and fill in the gap c.
The screws are not required for granite
tops.
Installation KM 4 4 / KM 4 7
19
c
d

Fixing the support brackets
^Position the two support brackets
supplied ain the positions shown in
"Fitting the spacer bars and support
brackets" so they are flush with the
top edge of the cut-out and secure
using the 3.5 x 25 mm screws
supplied. 2 screws are needed to
secure each support bracket.
The thickness of the worktop will
determine which drill hole is used.
Granite worktops
On a granite worktop a hole must be
drilled dat the position indicated to
secure each support bracket.
^Using a piece of strong, double-
sided adhesive tape position the
support brackets supplied aat the
positions indicated flush with the top
edge of the worktop and secure each
bracket with one screw in hole das
shown.
Building in the gas hob
^Lay the gas hob in the prepared
cut-out.
^Draw the electricity connection cable
through the cut-out and connect.
^Make the gas connection (see
chapter "gas connection").
^Secure the gas hob from below
through the middle elongated hole b
in each support bracket using the
four screws supplied. Carefully adjust
the hob if necessary.
Installation KM 4 4 / KM 4 7
20