Miele H 2261 B User manual

Installation Instructions
+%HQ&$



,QVWDOODWLRQUHSDLUDQGPDLQWHQDQFHZRUNVKRXOGEHSHUIRUPHGE\
D0LHOHDXWKRUL]HGVHUYLFHWHFKQLFLDQLQDFFRUGDQFHZLWKQDWLRQDO
DQGORFDOVDIHW\UHJXODWLRQVDQGWKHSURYLGHGLQVWDOODWLRQLQVWUXFWLRQV

Electrical connection
74
ɘCAUTION:
Before servicing, disconnect the
power supply by either removing the
fuse, shutting off the power main or
manually "tripping" the circuit
breaker.
Installation, repair and maintenance
work must be performed by a Miele
authorized service technician. Work
by unqualified persons could be
dangerous and may void the
warranty.
Before connecting the appliance to
the power supply, make sure that the
voltage and frequency listed on the
data plate correspond with the
household electrical supply. This
data must correspond to prevent
machine damage. Consult an
electrician if in doubt.
Only operate the appliance after it
has been installed into cabinetry.
The power cable plug must be
inserted into a suitable outlet that
has been installed and grounded in
compliance with all applicable local
regulations.
WARNING: THIS APPLIANCE MUST
BE GROUNDED
Installer: Please pass these
instructions on to the customer.

Electrical connection
75
Data plate
The silver data plate is located along
the front side of the oven with the door
open (see "Guide to the oven").
ɘBefore connecting the appliance
to the power supply, make sure that
the voltage and frequency listed on
the data plate correspond with the
household electrical supply. This
data must correspond to prevent
machine damage. Consult an
electrician if in doubt.
H2261B: Electrical connection
208 V
ɘDo not connect the oven to a
240 V power supply.
The oven is equipped with a 6' 3"
(1.9 m) long flexible power cord with a
NEMA 14-30P plug, ready for
connection to a 120/208 V, 60 Hz, 20 A
power supply.
Maximum connected load: 3,600 W
H2261B: Electrical connection
240 V
The oven is equipped with a 6' 3"
(1.9 m) long flexible power cord with a
NEMA 14-30P plug, ready for
connection to a 120/240 V, 60 Hz, 20 A
power supply.
Maximum connected load: 3,800 W
H2260E: Electrical connection
208 V
ɘDo not connect the oven to a
240 V power supply.
The oven is equipped with a 6' 3"
(1.9 m) long flexible power cord with a
NEMA 14-50P plug, ready for
connection to a 120/208 V, 60 Hz, 40 A
power supply.
Maximum connected load: 9,700 W, in
combination with Miele cooktop
KM6002.
H2260E: Electrical connection
240 V
The oven is equipped with a 6' 3"
(1.9 m) long flexible power cord with a
NEMA 14-50P plug, ready for
connection to a 120/240 V, 60 Hz, 40 A
power supply.
Maximum connected load: 9,900 W, in
combination with Miele cooktop
KM6002.
SAVE THESE INSTRUCTIONS FOR
THE ELECTRICAL INSPECTOR'S
USE.
NEMA 14-30P, L1, L2, N, G, 20 amp
208/240 VAC

Installation diagrams
76
Appliance and cut-out dimensions
Undercounter installation
A
B
A
B
7/8" (23 mm)
21 9/16" (547 mm)
22 1/2"
(572 mm)
21 7/16" (544 mm)
23 7/16"
(595 mm)
23 7/16"
(596 mm)
22 1/16"
(560 mm)
4"
(100 mm)
23 5/8"
(600 mm)
21 5/8"
( 550 mm)
ǞCut-out for power cord with plug (min. 4" x 22" / 100 mm x 560 mm) in the
bottom of the cabinet
ǟPower cord with plug

Installation diagrams
77
Installation into a tall cabinet
A
B
A
B
7/8" (23 mm)
21 9/16" (547 mm)
22 1/2"
(572 mm)
21 7/16" (544 mm)
23 7/16"
(595 mm)
23 7/16"
(596 mm)
22 1/16"
(560 mm)
4"
(100 mm)
590-595 mm
(23 1/4"-23 7/16")
21 5/8"
( 550 mm)
ǞCut-out for power cord with plug (min. 4" x 22" / 100 mm x 560 mm) in the
bottom of the cabinet
ǟPower cord with plug

Installing the oven
78
ɘThe oven must not be operated
until it has been properly installed
within cabinetry.
In order for the oven to function
correctly, it required an adequate
supply of cool air. Ensure that the air
flow is not impaired (e.g. insulation in
the cabinetry). Also be sure that the
cool air supply is not heated by other
sources nearby.
Before installation
ĺBefore connecting the oven to the
power supply, first disconnect the
power supply from the oven isolator
switch.
Installing the oven
ĺConnect the power cord to the
electrical supply.
Do not carry the oven by the door
handle. The door can be damaged.
Use the handles on each side of the
oven to carry it.
It is recommended that you remove
the door before installing the
appliance (see "Cleaning and Care -
Removing the door") and all oven
accessories from the cavity. This will
make for easier installation into the
niche and will not tempt you to use
the handle to carry it.
ĺIf there are side handles, please
remove them.
ĺPush the oven into the cabinetry and
align it.
ĺOpen the door (if it was not removed
previously).
ĺUse the supplied screws to secure
the oven to the side walls of the
cabinetry through the holes in the
trim.
ĺReinstall the door, if necessary (see
"Cleaning and care - Installing the
door").

Installing the combination oven/cooktop
79
ɘThe combination oven/cooktop
must not be operated until it has
been properly installed within
cabinetry.
In order for the combination oven/
cooktop to function correctly, it
required an adequate supply of cool
air. Ensure that the air flow is not
impaired (e.g. insulation in the
cabinetry). Also be sure that the cool
air supply is not heated by other
sources nearby.
Before installation
ĺBefore connecting the oven to the
power supply, first disconnect the
power supply from the oven isolator
switch.
Installing the combination oven/
cooktop
ĺConnect the power cord to the
electrical supply.
ĺAlign the oven with the front of the
cabinetry.
ĺConnect the cooktop plug to the
socket on the range.
Do not carry the oven by the door
handle. The door can be damaged.
Use the handles on each side of the
range to carry it.
It is recommended to remove the door
before installing the appliance (see
"Clean and Care - Removing the
door") and remove the accessories
from the oven cavity. This will make it
easier to install the oven in its niche,
and ensure that you will not use the
door handle to lift it.
ĺPush the oven into the cabinetry and
align it.
ĺOpen the door (if it was not removed
previously).
ĺUse the supplied screws to secure
the oven to the side walls of the
cabinetry through the holes in the
trim.
ĺReinstall the door, if necessary (see
"Cleaning and care - Installing the
door").

9 Independence Way
Princeton, NJ 08540
Phone:
Fax:
www.mieleusa.com
U.S.A.
Miele, Inc.
National Headquarters
Please have the model and serial number
of your appliance available before
contacting Technical Service.
Canada
Importer
Miele Limited
Headquarters and Miele Centre
800-843-7231
609-419-9898
609-419-4298
Technical Service & Support
Nationwide
Phone:
Fax:
[email protected]
161 Four Valley Drive
Vaughan, ON L4K 4V8
www.miele.ca
800-999-1360
888-586-8056
Customer Care Centre
Phone:
[email protected]
800-565-6435
905-532-2272
Germany
Manufacturer
Miele & Cie. KG
Carl-Miele-Straße 29
33332 Gütersloh
80

M.-Nr. 09 786 731 / 00en–US, CA
H2260E; H2261B
ħ