Miele DGC 5080 User manual

Installation instructions
Steam combi oven
DGC 5080
To avoid the risk of accidents or
damage to the appliance it is
essential to read these
instructions before it is installed
and used for the first time. M.-Nr. 07 223 420
en-GB

Safety instructions for installation....................................3
Appliance and building-in dimensions ................................4
Installation in a tall unit...............................................4
Installation in a base unit .............................................6
Installation in a tall unit in combination with an oven........................8
Installing the appliance ............................................10
Electrical connection..............................................11
Connection cable..................................................12
Energy efficiency class ............................................13
Contents
2

The appliance must be installed by
a suitably qualified and competent
person in strict accordance with
current national and local safety
regulations.
~Before installation, check the
appliance for visible signs of damage.
~Before connecting the appliance,
make sure that the connection data on
the data plate (voltage and connected
load) match the mains electricity
supply. Consult a qualified electrician if
in any doubt.
~The electrical safety of this
appliance can only be guaranteed
when continuity is complete between it
and an effective earthing system which
complies with current local and national
safety regulations. It is most important
that this basic safety requirement is
present and regularly tested, and
where there is any doubt, the
household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
~This appliance may only be used in
mobile installations if a risk assessment
of the installation has been carried out
by a suitably qualified engineer.
~The appliance must be positioned
so that you can see the contents of a
cooking container placed on the top
runner. Otherwise you may risk
scalding or burning yourself with hot
water and food when taking containers
out of the oven.
Keep these instructions in a safe place
and pass them on to any future user.
All dimensions in this instruction booklet
are given in mm.
Safety instructions for installation
3

Installation in a tall unit
aSteam combi oven
bBuilding-in recess
cInlet for mains connection cable to the appliance
dRecommended position for electrical connection.
Important: Do not position behind the appliance!
eMains connection cable
* Appliances with glass front
** Appliances with metal front
Appliance and building-in dimensions
4

Cut-out for venting the steam combi oven
To ensure that the steam combi oven has adequate ventilation, a cut-out of 500 x
30 mm must be provided in the interim shelf above the appliance in the building-in
niche aand also in the top of the tall unit b. No back panel may be present
either behind the building-in niche or behind the area above the interim shelf in
the tall unit.
Appliance and building-in dimensions
5

Installation in a base unit
aSteam combi oven
bBuilding-in recess
cInlet for mains connection cable to the appliance
dRecommended position for electrical connection.
Important: Do not position behind the appliance!
eMains connection cable
* Appliances with glass front
** Appliances with metal front
Appliance and building-in dimensions
6

Cut-out for venting the steam combi oven
To ensure that the steam combi oven has adequate ventilation, a cut-out of 500 x
30 mm must be provided in the base of the building-in niche aand also in the
base of the area underneath it b. No back panel may be present either behind
the building-in niche or behind the area underneath it.
Appliance and building-in dimensions
7

Installation in a tall unit in combination with an oven
aSteam combi oven
bBuilding-in recess
cInlet for mains connection cable to the appliance
dRecommended position for electrical connection.
Important: Do not position behind the appliance!
eMains connection cable
fOven
* Appliances with glass front
** Appliances with metal front
Appliance and building-in dimensions
8

Cut-out for venting the steam combi oven
To ensure that the steam combi oven has adequate ventilation, a cut-out of
500 x 30 mm must be provided in the interim shelf above the appliance in the
building-in niche aand also in the top of the tall unit b. No back panel may be
present either behind the building-in niche or behind the area above the interim
shelf in the tall unit.
Cut-out for venting the oven:
Please refer to the installation instructions for the oven.
Appliance and building-in dimensions
9

^Push the appliance into the recess and align it.
^Secure the appliance by screwing the two wood screws
3.5x25mmi(supplied) into the vertical trim on either
side of the appliance (see illustration).
Installing the appliance
10

All electrical work should be carried out by a suitably
qualified and competent person, in strict accordance with
current local and national safety regulations (BS 7671 in
the UK).
Installation, repairs and other work by unqualified persons
could be dangerous. The manufacturer cannot be held
liable for unauthorised work.
Ensure power is not supplied to the appliance until after
installation work has been carried out.
The appliance must only be operated when built-in. This is
to ensure that all electrical parts are shielded. Live parts
must not be exposed.
Please ensure that the connection data quoted on the data
plate match the household mains supply.
This appliance is supplied with a cable for connection to a
suitable fused isolator which complies with national and local
safety regulations by a suitably qualified electrician.
If the switch is not accessible after installation (depending on
country) an additional means of disconnection must be
provided for all poles.
For extra safety it is advisable to protect the appliance with a
residual current device (RCD).
When switched off there must be an all-pole contact gap of
3 mm in the isolator switch (including switch, fuses and
relays).
Electrical connection
11

Important U.K.
This appliance is supplied for connection to a single phase
230 V 50 Hz supply with a 3-core cable.
The wires in the mains lead are coloured in accordance with
the following code:
Green/yellow = earth
Blue = neutral
Brown = live
WARNING: THIS APPLIANCE MUST BE
EARTHED
Important
The electrical safety of this appliance can only be guaranteed
when continuity is complete between the appliance and an
effective earthing system, which complies with local and
national regulations. It is most important that this basic safety
requirement is tested regularly and where there is any doubt
the household wiring should be inspected by a qualified
electrician. The manufacturer cannot be held liable for the
consequences of an inadequate earthing system such as
electric shock.
The manufacturer cannot be held liable for damage
caused by incorrect installation or connection.
Connection cable
A damaged cable must be replaced with a special pvc
insulated connection cable of type H 05 VV-F, available from
Miele.
It must be replaced by a Miele approved service technician.
The connection data are quoted on the data plate.
Electrical connection
12

This appliance is rated energy efficiency class A in
accordance with EN 50304. Tests were carried out using
"Cake plus".
Energy efficiency class
13

14

15

Alteration rights reserved / 0610 M.-Nr. 07 223 420 / 05