MIJO MT01 User manual

MANUAL INSTRUCTION
FOR HANDBIKE ATTACHMENT
User: Before using the handbike, please read this
manual instruction carefully and save it for reference.
MODEL: MT01 & MT02

Contents
Product description............................................................................................................................. 2
Product Structure........................................................................................................................ 2
Technical Parameters and Indicators.................................................................................................. 4
Product main parameters........................................................................................................... 4
Unpacking Installation Instructions.....................................................................................................5
Foot support installation............................................................................................................. 5
Unfolding the foldable handlebar...............................................................................................5
MT01 Connection structure matching with manual wheelchair................................................6
MT01 First time connecting with wheelchair instruction.......................................................... 7
MT01 Disconnecting with wheelchair........................................................................................ 9
MT02 Manual Instruction..................................................................................................................10
MT02 Connection structure diagram........................................................................................10
MT02 Clamp installation position............................................................................................. 10
MT02 First time connecting with wheelchair instruction........................................................ 11
MT02 Disconnecting with wheelchair instruction....................................................................14
Battery Instructions...........................................................................................................................15
Related battery instructions......................................................................................................15
Battery Usage............................................................................................................................ 15
Notes for charging.....................................................................................................................16
Battery Installation and removal...............................................................................................18
Battery Charging........................................................................................................................19
Over Discharge Protection Device............................................................................................ 19
Over current protect device......................................................................................................19
Warranty Coverage............................................................................................................................20
Labels, Packing Logo Design..............................................................................................................22
Accessories........................................................................................................................................ 23

2
Product description
Product Structure
The handbike consists of disc brake systems, combination switch, handlebars, meter,
power switch, pneumatic tire, quick release pin,foot support, fender, reflectors, and
motors, battery, battery lock button, battery key, etc.

3
【Scope of application】
It’s used to help wheelchair users to gain freedom.
【Intended Usage Environment】
The handbike is suitable for outdoor and indoor, hospital, nursing home and home, etc.
Temperature: 5±2℃～40±2℃;
Atmospheric pressure: 860±2%hPa～1060±2%hPa;
Humidity: 10±3%～80±3%
【Power condition
Charging voltage: AC 100±2%V～240±2%V,50±1%Hz;
Battery voltage: DC 36±2%V;
Motor power: ≥250W;
Warning: Do not make sharp turns when you are driving at high speed.
【For people】
The disabled and the elderly infirm with mobility difficulties.
【Initial Install】
Must be approved by our company the professional and technical staff from our company.

4
Technical Parameters and Indicators
Product main parameters
Size and weight
Expanded size (length x width x height)
950*520*710mm
Folded size (length x width x height)
1120*460*410mm
Weight capacity
100kg
Self-weight
14.1kg (Without battery)
Motor
Type
Brushless DC motor
Rated power
350
Input voltage
DC 36V
Number
1 PC
Brake system
Disc brake
Battery
Type
Lithium-ion Battery
Nominal capacity
13 Ah/20 Ah
The output voltage
DC 36V
Number
1(If not used for 2 weeks, charge once)
Controller
Type/plug type
Brushless DC sine wave controller
Output voltage/current
DC 36V
Charger
Type
Take away portable
Input voltage
AC: 100～240V,50Hz
The output voltage
36V
Tires
Outer diameter x tire width
12.5 Inch *2.125 Inch
Type
Pneumatic tire
Material
Rubber
Number
1 PC
Performance
Horizontal road braking performance
≤3m
Maximum safe slope performance
≤3m (8°)
Climbing ability
≤8°
Theoretical driving distance
40-50km
Maximum Speed
25km/h

5
Unpacking Installation Instructions
Foot support installation
1. Foot support installation：As shown in the picture, install the foot support on the
frame with an inner hexagon (tool: 5mm inner hexagon wrench).
Unfolding the foldable handlebar
1. Rotate the left and right handlebars to the outside directions by 90°, when the slider is
automatically returned to the position, unfolding the handlebar is complete.

6
MT01 Connection structure matching with manual
wheelchair
1. Loosen the width adjustment bolts①and adjust the width of the connection on
both sides to make it consistent with the width of the bridge tube of the wheelchair.
2. Adjust the pipe clamp adjusting bolts ②to make the pipe clamp suitable for pipe
diameters of different thicknesses (the pipe clamp should be clamped on the frame
protective case to prevent the frame from being pinched).

7
MT01 First time connecting with wheelchair instruction
1. Press the safety catch lever to keep the body standing steadily.
2. As shown in figure,Clamp the pipe clamp to a suitable frame of the wheelchair
(Note: After the pipe clamps on both sides clamped, the bubble of gradienter should
be in the middle);
The knob must be tightened
40 CM

8
3.As shown in figure，press the wire control switch to the unlocked state and hook
the upper hook into the lock.
4.Push the handlebar forward and upwards, when you hear a "click", the handbike is adjusted in
place. after that, lift up the safety catch lever ,turn on the power switch and you can ride.

9
MT01 Disconnecting with wheelchair
1. First press the safety catch lever to keep the body standing steadily ,then press the
connector switch，at the same time push the handlebar forward and upwards,finally
lower the handlebar so that the front wheel and foot support of the wheelchair touch
the ground;
2. Loosen the both side knobs to separate the front of the handbike from the
wheelchair;

10
MT02 Manual Instruction
MT02 Connection structure diagram
1. As shown in the picture, assemble the MT02 accessory and adjust it to fit the
wheelchair.
MT02 Clamp installation position
1. As shown in the figure below, the frame pipe clamp can be installed in three
positions on the wheelchair (different installation positions are selected according to
different wheelchairs).
Upper part of wheelchair
Lower part of wheelchair
Front of wheelchair

11
MT02 First time connecting with wheelchair instruction
1. Loosen the quick-release-pin of the connection pipe first, adjust the overall width,
and install the frame tube clamp on the wheelchair. (The intermediate connecting
pipes on both sides are about 40cm away from the ground, and the small hole in the
middle connecting piece is at the rear).
2. Loosen the bolts of the middle connecting piece and adjust the installation hole of
the middle connecting piece to be parallel to the ground.
Center
40cm

12
3. Press the release switch of the middle connecting rod, and install the middle
connecting rod to the middle connecting piece.
4. As shown in figure，press the wire control switch to the unlocked state and hook the
upper hook into the lock.
Control

13
4. Push the handlebar forward and upwards, when you hear a "click", the handbike is
adjusted in place. after that, lift up the safety catch ,turn on the power switch and
you can ride.

14
MT02 Disconnecting with wheelchair instruction
1.First press the safety catch lever to keep the body standing steadily ,then press the
connector switch，at the same time push the handlebar forward and upwards,finally
lower the handlebar so that the front wheel and foot support of the wheelchair touch
the ground;
3. If necessary, press the middle connecting rod to disengage the switch and pull the
middle connecting rod forward.

15
Battery Instructions
Related battery instructions
Battery Usage
The positive and negative poles of the battery cannot be connected with conductive
objects such as metal, which may cause a short circuit or electric shock.
Do not approach flammable materials.
Do not approach or expose to heat sources, such as open flames or sparks.
Do not transport the battery with flammable or combustible materials.
There are corrosive chemicals in the battery box. It is strictly forbidden to disassemble
the battery without permission.
It is strictly forbidden to short-circuit the battery or throw the battery into the fire to
avoid an explosion accident.

16
Notes for charging
Warning
1. Do not try to use pliers or cable wires to directly connect the battery terminals to
charge the battery.
2. Do not use the handbike when charging the battery.
Do not use non-standard power sources (such as generators or inverters), even if their
voltage and frequency appears to meet the requirements.
3. Prevent the power cord from being stepped on, pinched and severely bent,
especially at the port. Prevent the power cord from being yanked and knotted.
4. Keep children and pets away from the power cord, and do not let them chew or
chew the power cord. When unplugging the power cord, hold the plug and pull it out.
5. If the circuit breaker (circuit fuse) trips several times during charging, please unplug
the charger immediately and contact the dealer or professional technicians.
The battery warranty and performance indicators mentioned in this guide are all for
lithium-ion batteries.
Note
1. After the initial use of the new battery, the first time it is charged, it must be fully
charged (about 24 hours) to ensure that the battery is fully activated.
2. Before the initial use, if recharge all the time, which will reduce the service life of
the battery (the battery should be fully used up for the first time, and then start
charging, so that the battery can be fully activated.)
3. Check whether the power supply is sufficient before use, and charge in time when
the power is insufficient. When the power is exhausted, charging takes 6-8 hours, until
the red light on the charger turns green.
4. The recommended range for each battery charging time is about 6 to 8 hours.
5. Charge the battery frequently. As long as the trailer is in use, charge the battery
after use until it is fully charged. If the trailer is not used for a long time, please

17
recharge the trailer once every 2 months, charging about 80% of the electricity each
time. If the battery is out of power for a long time, the battery will be damaged, the
battery will be unusable, and the handbike will be damaged seriously.
6. If you use batteries with incorrect specifications, voltage and capacity, your
handbike may be damaged, and the handbike may not achieve the best performance
and effect.
7. The cycle times of the battery are 700 weeks, and the service period is 2-5 years. If
the battery is damaged, you can contact our company's after-sales service for
replacement.

18
Battery Installation and removal
Warning
Please make sure to turn off the power to the handbike before performing this
operation.
Remove the battery:
1. Pull up the battery to prevent tripping
2. Turn the key, after seeing the battery pop up, let go to return the key
3. Rotate the battery upward and remove the battery
Install the battery:
1. Put the battery in the battery box
2. Gently press down on the battery, after hearing a "click" sound, the battery is
installed in place.
3. Slide the battery anti-trip down to lock the battery.

19
Battery Charging
It can be charged with standard AC power (AC 110-220 V, 50-60 Hz). Make sure to turn
off the power of the handbike before charging.
Insert the charging plug of the charger into the charging port on the lower front of the
control panel and insert the battery charging port to charge (the battery can be
removed and charged separately, or it can be directly charged on the handbike).
1. Insert the charger plug into the network power supply. When the red indicator light
is on, it means it is charging.
2. The red indicator light is on to indicate that it is charging. When the charger
indicator turns from red to green, keep charging for another 30 minutes to ensure
that the battery is fully charged.
3. After charging is completed, unplug the network power socket first, and then
unplug the charging plug.
4. Please charge at 0-45°C in an environment suitable for charging.
Over Discharge Protection Device
When the battery of the handbike is exhausted, the over-discharge protection device
will protect the battery from over-discharge. The user should note that the maximum
speed will decrease when the over-discharge protection device is activated. In this
case, please charge the battery as soon as possible.
Over current protect device
This handbike also equipped with an overcurrent protect device. If the current
supplied to the motor becomes excessive, the electronic fuse will turn off the current.
When driving a handbike in trouble, overcurrent protection will be activated, and the
driving wheels of the wheelchair will be blocked in motion. This process is the fuse cut
off the current to prevent the motor from overheating and damage.