MILL AB-H700MINI User guide

ASSEMBLY AND INSTRUCTION MANUAL (EN)
Please read the instrucons carefully before use. Take good care of this manual for later use.
This assembly and instrucon manual applies to the following products:
AB-H700MINI, AB-H1000DN, AB-H1500DN, AB-H2000DN
Series: Oil

Important safety informaon
You must obey common safety guidelines when using electrical products, especially in the presence of children.
WARNING! To avoid electric shock or damage due to the heat, always make sure the plug is pulled out before the heater is moved or
cleaned.
Read the instrucons carefully.
The product is intended for home use only.
Make sure the heater is connected to the house's regular mains (230 V), as it indicated on the heater.
New heaters will produce a specic odor when used the rst me. This will stop aer a short me and is completely
harmless.
Check for any pieces of packing foam or cardboard that may have fallen into the heang elements of the heater. These
pieces must be removed in order to avoid unpleasant odors.
Prevent the heater from overheang – do not cover.
Always turn o the heater and unplug it when not used for a long me.
Pay special aenon if the heater is used in rooms where children, the handicapped or elderly reside.
The heater should not be set up directly beneath an electrical socket outlet.
The cord must not be laid under any kind of carpet. Make sure the cord is laid in such a way that nobody can trip on it.
The heater must not be used if either the cord or plug is damaged. The heater must not be used if it has been dropped on
the oor or is damaged in any other way causing it to malfuncon.
The cord must be repaired by the manufacturer or by an expert if it has been damaged, to avoid dangerous situaons.
Avoid using extension cords, which may overheat and could possibly start a re.
Never cover the air vents on the heater. Avoid potenal re hazards by making sure the air intakes are not blocked or
covered. The heater should be used in rooms with normal at oors.
The heater should not be installed in close proximity to ammable materials of any kind because there can always be a risk
of re.
The heater must never be used in rooms where gasoline, paint or other ammable liquids are stored, such as in a garage.
Never touch an electric heater with wet hands. The heater should be installed so a person showering or taking a bath
cannot come into direct contact with it.
The heater becomes hot when it is on. Therefore, be careful and avoid burning or scorching your skin.
The heater must be switched o, the plug removed and the heater must cool down before it is moved.
Avoid overloading the mains (the circuit) where the heater is connected. The heater may overload the electrical circuit if
other electrical devices are plugged into the same socket outlet.
EN 2 millheat.com

The device cannot be used by children under 8 years of age and persons with reduced physical or mental abilies or lack of
experience and knowledge unless they have been given supervision or instrucon in the safe use of the device and
understand the hazards involved.
Children should not play with the device. Cleaning and maintenance should not be done by unsupervised children.
Children under the age of 3 should be kept away from the device, unless they are under constant supervision.
Children aged 3 to 8 years are only permied to turn the device ON/OFF, assuming the device is mounted according to the
assembly instrucons and the children have received instrucon or supervision in the safe use of the device and
understand the hazards involved.
EN 3 millheat.com

STORE THIS INSTRUCTION MANUAL FOR FUTURE USE!
NEVER TOUCH YOUR PANEL HEATER OR ITS CASING WITH WET HANDS!
EN 4 millheat.com
Model Thermostat Color Amperage Power (W) Mill Heat Boost
AB-H700MINI Mechanical White ~230 V / 50 Hz 700 Yes
AB-H1000DN Day/night White ~230 V / 50 Hz 1000 Yes
AB-H1500DN Day/night White ~230 V / 50 Hz 1500 Yes
AB-H2000DN Day/night White ~230 V / 50 Hz 2000 Yes
Specicaons
Before rst use
Aer unpacking the heater, check to make sure the product was not damaged during transport. Contact the retailer or
importer if you discover any visible damages to the product.
Keep the outer packaging to transport the heater in the future. If you want to dispose of the packaging, make sure it is
done properly. Keep plasc bags away from children.
First use
Aer turning on the heater for the rst me or aer an extended period without use, the heater can produce a burnt odor
for a short me. This is normal.
Please read all the instrucons carefully before use. Save the instrucon manual for future use.
It is also normal for the heater to make sounds when it warms up or cools down.
DO NOT COVER

EN 5 millheat.com
Descripon of the heater
1. Heat emission
2. Indicator light
3. OFF/ON
4. Legs (aluminum)
1. Heat emission
2. LED display
3. Thermostat
4. Output selector
5. OFF/ON
6. Legs (aluminum)
Parts
 8 screws (4 of which are pre-mounted)
 2 foot brackets
 2 rails for the feet

EN 6 millheat.com
Assembly
1. Insert both legs into the brackets so you get a stable foot (as shown in Picture 1 below).
2. Aach the legs to the brackets by ghtening 2 screws into each bracket (see the picture below).
3. Remove the pre-mounted screws from the boom of the heater and place the heater gently on its head to mount
the feet.
4. Two screws must be fastened on each foot bracket (as shown in Picture 2 below).
5. NEVER USE THE HEATER BEFORE THE LEGS HAVE BEEN TIGHTLY SCREWED.

AB-H700MINI — Instrucons
Control panel for AB-H700MINI
1. Indicator light
2. OFF/ON
WARNING: Be sure the foot is ed correctly and according to the instrucons before using the heater!
Use
Set the heater to OFF. Plug the heater into a grounded outlet.
1. Set the heater to ON. The indicator light will be lit when the heang elements are heang up.
2. To turn o the heater, set the output selector to OFF. If the heater will be le unused for a longer period of me, pull out
the plug.
3. The heater has an overheat protecon that turns the device o if any parts become extremely hot.
EN 7 www.millovn.no

AB-H1000DN/1500DN/2000DN — Instrucons
Control panel for AB-H1000DB/1500DN/2000DN
1. Standby
2. Dayme setback
3. Nighme setback
4. Power indicator — Shows whether the heater is using power or not
5. Desired room temperature
6., 7., 8. Indicates the output level
9. Timer funcon
10. Dayme setback acvaon buon
11. Nighme setback acvaon buon
12. Funcon buon
13. Timer acvaon buon
14. Thermostat and output selector:
i. Turn the selector to the le to decrease the temperature, and turn the selector to the right to increase the temperature.
ii. Push the buon to change the desired power level. 3 power levels.
WARNING: Be sure the foot is ed correctly and according to the instrucons before using the heater!
EN 8 millheat.com
If the temperature sensor is not funconing properly, you will see the symbol below on the display. Please contact
the dealer or importer.

EN 9 millheat.com
Using AB-H1000DN/1500DN/2000DN
1. Plug the heater into a grounded outlet.
2. Press OFF/ON buon.
3. Choose the desired power |, || or |||, by pressing the output selector.
Turn the thermostat to the desired temperature while looking at the
display. As soon as the room temperature drops below this level, the
heater will automacally start again. When the room has reached the
desired temperature again, the heater will turn itself o.
4. The thermostat goes from 5 to 35°C.
5. If you want to change the temperature in the room, repeat step 3.
6. The heater has an overheat protecon that turns the device o if any
parts become extremely hot.
7. To turn o the heater, press the OFF/ON buon. Should the heater be le
unused for a longer period of me, pull out the plug.
TIMER FUNCTION
The mer funcon will turn o the heater aer a desired number of hours have passed.

EN 10 millheat.com
1) Dayme setback
When you want the heater to reduce the
temperature during the day (set for
weekdays from now on) press . . The
display shows "d".
Enter the correct weekday. (Monday = 1,
Tuesday = 2, Wednesday = 3, Thursday =
4, Friday = 5, Saturday = 6, Sunday = 7).
Save by pressing this: .
Enter the desired temperature for
dayme setback. Save by pressing .
Enter the desired number of hours for
dayme setback. Save by pressing .
*Control light is steady green when
the heater is in an acve setback period.
The control light is steady white when the
setback period is inacve, but has been
programmed.
ADVANCED SETTINGS
2) Nighme setback
When you want the heater to reduce
the temperature in the evening
(applicable every evening/night from
now on) press . The display shows °C.
Enter the desired temperature for
nighme setback. Save by pressing .
Enter the desired number of hours for
nighme setback. Save by pressing .
*Control light is steady green when
the heater is in an acve setback period.
The control light is steady white when
the setback period is inacve, but has
been programmed.

EN 11 millheat.com
3) Change setback
temperature — Dayme
Press and hold and press 3 mes.
Enter the desired temperature for
dayme setback. Save by pressing or
wait for 15 seconds for automac
conrmaon.
4) Change setback
temperature — Nighme
Press and hold and press 3 mes.
Enter the desired temperature for
nighme setback. Save by pressing or
wait for 15 seconds for automac
conrmaon.
5) Change number of hours
— Dayme
Press and hold and press 2 mes.
Enter the desired number of hours for
dayme setback. Save by pressing or
wait for 15 seconds for automac
conrmaon.
6) Change number of hours
— Nighme
Press and hold and press 2 mes.
Enter the desired number of hours for
nighme setback. Save by pressing
or wait for 15 seconds for automac
conrmaon.

EN 12 millheat.com
7) Cancel (skip) setback
period
Press and hold and press or
once (depending on which setback
period you want to cancel).
*The heater will skip an acve setback
period or the next setback period.
*During the next setback period, the
heater will automacally resume the
programmed temperature reducon.
8) Delete a setback program
Press and hold or (depending on
which setback period you want to
cancel) for 3 seconds.
9) Temperature calibraon
* Should any deviaons occur between
the desired and actual temperature in
the room, it can be easily adjusted (the
heater should have been set to the same
seng for at least 12 hours in order to
be sure a calibraon is necessary).
Press 2 mes and use + or − to set the
actual temperature observed in the
room. Conrm with or wait for 15
seconds for automac conrmaon.
10) Reseng the heater
Turn o the heater's main switch.
Press and hold while you turn on the
heater's main switch.
11) Memory funcon
*The heater remembers all the
temperature sengs and will
automacally return to the desired
temperature aer a power failure. If you
have changed the temperature seng
for the various setback program, the
heater will also remember it.

Maintenance
1) For cleaning, always unplug the heater and leave it to cool.
2) Wipe the heater regularly with a damp cloth and dry the surface before turning on the heater again.
3) The heater must be cleaned at least once a month during the heang season.
Cauon! The heater should never be immersed in water.
Avoid using detergents to clean the heater.
Never let any water get inside the heater; this can be hazardous.
4) Dust etc. should be removed with a so cloth.
5) The heater can be stored in a dry and clean place.
6) If the heater stops working, do not aempt to repair it yourself because it can cause a re hazard and/or electric shock.
Warranty
The warranty is valid for 2 years. The heater will be repaired or replaced during this me should any malfuncon occur. The
warranty applies if the heater is used according to these instrucons and the customer can present a purchase receipt. If the
heater malfuncons in any way, please contact the store where it was purchased or the importer.
Waste disposal
The symbol indicates that this product is to be disposed of together with household waste. This product must be
delivered to a recycling service or container for electrical appliances and electronic equipment. This is done to avoid health
risks and prevent harm to the environment. Local businesses (or the environmental staon in your neighborhood) are
required by law to accept and recycle such products, as a means of environmentally sound disposal.
Mill Internaonal AS
Grini Næringspark 12
1361 Østeras
Tel.: [phone]
www.millheat.com
EN 13 millheat.com