Millart HS-800 User manual


V1.0





GUILLOTINESHEAR
OPERATIONMANUAL






V1.0
1

WARNING
Readandunderstandallinstructionsbeforeusingthistool.
Theoperatormustfollowbasicprecautionstoreducethe
riskofpersonalinjuryand/ordamagetotheequipment.

HAZARDDEFINITIONS
Pleasefamiliarizeyourselfwiththehazardnoticesfoundin
thismanual.Anoticeisanalertthatthereisapossibilityof
propertydamage,injuryorlossoflifeifcertaininstructions
arenotfollowed.
DANGER! Thisnoticeindicatesanimmediateandspecific
hazardthatwillresultinseverepersonalinjuryor
lossoflifeiftheproperprecautionsarenottaken.
WARNING!Thisnoticeindicatesaspecifichazardorunsafe
practicethatcouldresultinseverepersonalinjuryor
lossoflifeiftheproperprecautionsarenottaken.
CAUTION!Thisnoticeindicatesapotentiallyhazardoussituation
thatmayresultinminorormoderateinjuryifproper
practicesarenottaken.
NOTICE!Thisnoticeindicatesthataspecifichazardorunsafe
practicewillresultinequipmentorpropertydamage,
butnotpersonalinjury.

V1.0
2

WORKAREA
1. Operateinasafeworkenvironment,Keepyourworkareaclean,
well‐litandfreeofdistractions.Placelightssoyouarenot
workinginashadow.
2. Keepanyonenotwearingtheappropriatesafetyequipment
awayfromtheworkarea.
3.Storeunusedtoolsproperlyinasafeanddrylocationtoprevent
rustordamage.Locktoolsawayandkeepoutofthereachof
children.

Usage
1. Thismachineissuitableforshearingmetalplateandplasticplate.

2. Maintechnicalspecification
ModelHS‐800
Bedwidth31‐1/2”(800mm)
Shearingthickness16Gauge(1.5mm)
N.W121.2lbs(55kg)
G.W134.5lbs(61kg)
Packingsize32‐7/8”x10‐5/8”x17‐21/64”
835mmx270mmx440mm




V1.0
3

3.Installationandcaution
3.1Installation
3.1.1Pleasecheckwhetherthepartofthismachinearefullyequipped
andnotdamagedaccordingtothepartslistorpartfigure.
3.1.2Thismachineshouldbemountedonhardgroundorspecific
stand.
3.1.3Pleaseleaveplentyroomaroundthemachineforyoureasy
operating,inordertoavoidinjury.
3.1.4Pleaseremovetheanti‐rustgreaseonprocessingsurfacesand
somepartsincludedkerosene.
3.2Caution
3.2.1Pleasereadthemanualbeforeoperationandmakeyourself
understanditsstructureandprinciplecompletely.
3.2.2Pleasedon'toperatethematerialwidthandthicknessthan
tablelistmax.range.
3.2.3Pleasedon’ttouchthebladeduringoperation.

4.Maintenance
Lubricatetherotatingpartsofthemachineeveryday.




V1.0
4


5.Partslist
Part#DescriptionqtyPart#Descriptionqty
1Lowerblade112Screw4
2Bolt413Pin2
3Stand114Cover1
4Base115Screw4
5Shaft116Boardforupper
blade1
6Washer417Screw4
7Nut418Upperblade1
8Leg219Screw2
9Pin120Handle1
10Washer221Handlesleeve1
11Nut422Spring 1 









V1.0
5


6.Assemblydiagram


