Arconic 256 User manual

Patent Pending
August 23, 2017
HK1015
Makers of Huck®, Marson®, Recoil®
Brand Fasteners, Tools & Accessories
Declaration of Conformity
2
Safety Instructions
3
Principle of Operation
4
Tool Specications
4
Preparation for Use
5
Maintenance
5
Operating Instructions
6
Disassembly Procedure
6-7
Assembly Procedure
8
Fill and Bleed Procedure
9
Components Drawings
10-11
Troubleshooting
14
Accessories
14
Instruction Manual
256
Pneudraulic Installation Tool

256 Pneudraulic Installation Tool (HK1015)
2

256 Pneudraulic Installation Tool (HK1015)
3
I. GENERAL SAFETY RULES:
1.Ahalfhourlonghands-ontrainingsessionwithqualiedpersonnelis
recommendedbeforeusingHuckequipment.
2.Huckequipmentmustbemaintainedinasafeworkingconditionatall
times.Toolsandhosesshouldbeinspectedatthebeginningofeach
shift/dayfordamageorwear.Anyrepairshouldbedonebyaqualied
repairmantrainedonHuckprocedures.
3.Formultiplehazards,readandunderstandthesafetyinstructionsbefore
installing,operating,repairing,maintaining,changingaccessorieson,
orworkingneartheassemblypowertool.Failuretodosocanresultin
serious bodily injury.
4.Onlyqualiedandtrainedoperatorsshouldinstall,adjustorusethe
assemblypowertool.
5.Donotmodifythisassemblypowertool.Thiscanreduceeffectivenessof
safetymeasuresandincreaseoperatorrisk.
6.Donotdiscardsafetyinstructions;givethemtotheoperator.
7.Donotuseassemblypowertoolifithasbeendamaged.
8.Toolsshallbeinspectedperiodicallytoverifyallratingsandmarkings
required,andlistedinthemanual,arelegiblymarkedonthetool.The
employer/operatorshallcontactthemanufacturertoobtainreplacement
markinglabelswhennecessary.Refertoassemblydrawingandpartslist
forreplacement.
9. Tool is only to be used as stated in this manual. Any other use is
prohibited.
10.ReadMSDSSpecicationsbeforeservicingthetool.MSDS
specicationsareavailablefromtheproductmanufactureroryourHuck
representative.
11.OnlygenuineHuckpartsshallbeusedforreplacementsorspares.Use
ofanyotherpartscanresultintoolingdamageorpersonalinjury.
12.Neverremoveanysafetyguardsorpintaildeectors.
13.Neverinstallafastenerinfreeair.Personalinjuryfromfastenerejecting
may occur.
14.Whereapplicable,alwaysclearspentpintailoutofnoseassembly
before installing the next fastener.
15.Checkclearancebetweentriggerandworkpiecetoensurethereisno
pinchpointwhentoolisactivated.Remotetriggersareavailablefor
hydraulictoolingifpinchpointisunavoidable.
16.Donotabusetoolbydroppingorusingitasahammer.Neveruse
hydraulicorairlinesasahandleortobendorprythetool.Reasonable
careofinstallationtoolsbyoperatorsisanimportantfactorin
maintainingtoolefciency,eliminatingdowntime,andpreventingan
accidentwhichmaycauseseverepersonalinjury.
17.Neverplacehandsbetweennoseassemblyandworkpiece.Keephands
clear from front of tool.
18.Toolswithejectorrodsshouldneverbecycledwithoutnoseassembly
installed.
19.Whentwopiecelockboltsarebeingusedalwaysmakesurethecollar
orientationiscorrect.Seefastenerdatasheetforcorrectpositioning.
II. PROJECTILE HAZARDS:
1.Riskofwhippingcompressedairhoseiftoolispneudraulicorpneumatic.
2.Disconnecttheassemblypowertoolfromenergysourcewhenchanging
inserted tools or accessories.
3.Beawarethatfailureoftheworkpiece,accessories,ortheinsertedtool
itselfcangeneratehighvelocityprojectiles.
4.Alwayswearimpactresistanteyeprotectionduringtooloperation.The
gradeofprotectionrequiredshouldbeassessedforeachuse.
5. The risk of others should also be assessed at this time.
6.Ensurethattheworkpieceissecurelyxed.
7.Checkthatthemeansofprotectionfromejectionoffastenerorpintailis
inplaceandoperative.
8.Thereispossibilityofforcibleejectionofpintailsorspentmandrelsfrom
front of tool.
III. OPERATING HAZARDS:
1.Useoftoolcanexposetheoperator’shandstohazardsincluding:
crushing,impacts,cuts,abrasionsandheat.Wearsuitableglovesto
protecthands.
2.Operatorsandmaintenancepersonnelshallbephysicallyabletohandle
thebulk,weightandpowerofthetool.
3. Hold the tool correctly and be ready to counteract normal or sudden
movementswithbothhandsavailable.
4.Maintainabalancedbodypositionandsecurefooting.
5.Releasetriggerorstopstartdeviceincaseofinterruptionofenergy
supply.
6.Useonlyuidsandlubricantsrecommendedbythemanufacturer.
7.Avoidunsuitablepostures,asitislikelyforthesenottoallow
counteractingofnormalorunexpectedtoolmovement.
8.Iftheassemblypowertoolisxedtoasuspensiondevice,makesurethat
xationissecure.
9.Bewareoftheriskofcrushingorpinchingifnoseequipmentisnottted.
IV. REPETITIVE MOTION HAZARDS:
1.Whenusingassemblypowertool,theoperatorcanexperience
discomfortinthehands,arms,shoulders,neckorotherpartsofthebody.
2.Whenusingtool,theoperatorshouldadoptacomfortableposture
whilemaintainingasecurefootingandavoidawkwardoroffbalanced
postures.
3.Theoperatorshouldchangepostureduringextendedtaskstohelpavoid
discomfort and fatigue.
4.Iftheoperatorexperiencessymptomssuchaspersistentorrecurring
discomfort,pain,throbbing,aching,tingling,numbness,burning
sensationsorstiffness,thesewarningsshouldnotbeignored.The
operatorshouldtelltheemployerandconsultaqualiedhealth
professional.
V. ACCESSORIES HAZARDS:
1.Disconnecttoolfromenergysupplybeforechanginginsertedtoolor
accessory.
2.Useonlysizesandtypesofaccessoriesandconsumablesthatare
recommended.Donotuseothertypesorsizesofaccessoriesor
consumables.
VI. WORKPLACE HAZARDS:
1.Beawareofslipperysurfacescausedbyuseofthetoolandoftrip
hazardscausedbytheairlineorhydraulichose.
2.Proceedwithcautionwhileinunfamiliarsurroundings;therecouldbe
hiddenhazardssuchaselectricityorotherutilitylines.
3.Theassemblypowertoolisnotintendedforuseinpotentiallyexplosive
environments.
4.Toolisnotinsulatedagainstcontactwithelectricalpower.
5.Ensuretherearenoelectricalcables,gaspipes,etc.,whichcancausea
hazardifdamagedbyuseofthetool.
VII. NOISE HAZARDS:
1.Exposuretohighnoiselevelscancausepermanent,disablinghearing
lossandotherproblemssuchastinnitus,thereforeriskassessmentand
theimplementationofpropercontrolsisessential.
2.Appropriatecontrolstoreducetheriskmayincludeactionssuchas
dampingmaterialstopreventworkpiecefrom‘ringing’.
3.Usehearingprotectioninaccordancewithemployer’sinstructionsandas
requiredbyoccupationalhealthandsafetyregulations.
4.Operateandmaintaintoolasrecommendedintheinstructionhandbook
topreventanunnecessaryincreaseinthenoiselevel.
5.Select,maintainandreplacetheconsumable/insertedtoolas
recommendedtopreventanunnecessaryincreaseinnoise.
6.Ifthepowertoolhasasilencer,alwaysensurethatitisinplaceandin
goodworkingorderwhenthetoolisbeingoperated.
VIII. VIBRATION HAZARDS:
1.Exposuretovibrationcancausedisablingdamagetothenervesand
bloodsupplytothehandsandarms.
2.Wearwarmclothingwhenworkingincoldconditionsandkeephands
warm and dry.
3.Ifnumbness,tingling,painorwhiteningoftheskininthengersor
hands,stopusingthetool,tellyouremployerandconsultaphysician.
4.Supporttheweightofthetoolinastand,tensionerorbalancerinorder
tohavealightergriponthetool.
IX. PNEUMATIC / PNEUDRAULIC TOOL SAFETY INSTRUCTIONS:
1.Airunderpressurecancausesevereinjury.
2.Alwaysshutoffairsupply,drainhoseofairpressureanddisconnecttool
fromairsupplywhennotinuse,beforechangingaccessoriesorwhen
makingrepairs.
3.Neverdirectairatyourselforanyoneelse.
4.Whippinghosescancausesevereinjury,alwayscheckfordamagedor
loosehosesandttings.
5. Cold air should be directed away from hands.
6.Wheneveruniversaltwistcouplings(clawcouplings)areused,lockpins
shallbeinstalledandwhip-checksafetycablesshallbeusedtosafeguard
againstpossiblehosetohoseorhosetotoolconnectionfailure.
7.Donotexceedmaximumairpressurestatedontool.
8.Nevercarryanairtoolbythehose.
Safety Instructions
GLOSSARYOFTERMSANDSYMBOLS:
 - Productcomplieswithrequirementssetforthby
therelevantEuropeandirectives.
 - Readmanualpriortousingthisequipment.
 - Eyeprotectionisrequiredwhileusingthis
equipment.
 - Hearingprotectionisrequiredwhileusingthis
equipment.
Notes:areremindersofrequiredprocedures.
Bold, Italic type, and underline:emphasizeaspecic
instruction.
WARNINGS: Must be understood to avoid
severe personal injury.
CAUTIONS: Show conditions that will damage
equipment or structure.

256 Pneudraulic Installation Tool (HK1015)
4
1
2
12
10
11
5
6
3
4
9
7
Spring
8
Pressurized Air
Exhaust Air
Pressurized Hydraulic Fluid
Non-pressurizedHydraulicFluid
AirPiston
movesup
Exhaust Air
PullPiston
movesback
Hydraulic
PistonRod
movesup
ThrottleValve
movesdownto
(PULLposition)
Trigger
Depressed
Hydraulic
PistonRod
movesdown
ThrottleValve
movesupto
RETURNposition
Trigger
Released
PullPistonreturns
tohomeposition
Exhaust Air
WhentheTriggerisdepressed(1),the
ThrottleValvemovestothedownposition
(2),andpressurizedairisdirectedtothe
bottomoftheAirPiston,causingittomove
upward(3).TheairabovethePistonis
exhausted and directed through the center
oftheThrottleValveandoutthebottom
ofthetool(4).TheAirPistonhasaRod
andaHydraulicPistonattached.Whenthe
AirPistonrodmovesupward,acolumnof
pressurizedhydraulicuidisforcedup(5)
intothetoolhead,whichmovesthePull
Pistonback(6).Theattachednoseassembly
moveswiththePullPistontostartfastener
installation. When fastener installation is
completed,theTriggerisreleased(7).Air
pressure,withtheassistanceofaSpring(8),
causestheThrottleValvetoreturntoitsup
position(9).Pressurizedairisre-directedto
thetopoftheAirPiston,causingit,along
withtheHydraulicPistonRod,tomove
downward(10).TheairfrombelowtheAir
Pistonisexhaustedthroughthebottom
ofthetool(11).Asthisoccurs,hydraulic
pressureisreversedandthePullPistonis
returnedforward(12).Areturnpressure
reliefvalveprotectsthetoolagainstpressure
spikes.Thereservoirreplenishesthehydraulic
system as needed.
Principle of Operation
POWER SOURCE:
110psiMAXshopair
HOSE KITS:
UseonlygenuineHUCKHoseKits
rated@10,000psiworking
pressure.
HYDRAULIC FLUID:
HydraulicuidshallmeetDEXRON®
III,DEXRONVI,MERCON,AllisonC-4
orequivalentATFspecications.
Fireresistantuidmaybeusedif
itisanesterbaseduidsuchas
QuintolubricHFDorequivalent.
WaterbaseduidshallNOTbeused
asseriousdamagetoequipmentwill
occur.
WEIGHT: 11.1 lbs (5.03 kg)
MAX OPERATING TEMP:
125°F (51.7°C)
SPEED/CYCLES: 30perminute
MAX FLOW RATE:
22.4 scfm (634 l/m)
MIN PULL CAPACITY:
9986 lbs (44.42 kN) @ 90psi
MAX INLET PRESSURE:
110psi(6.2 bar)
MIN STROKE:
.875 inches (2.22 cm)
.750 inches (1.91 cm) when used with
Stroke Limiter 118362-1
Where the following trade names are used
in this manual, please note:
DEXRON is a registered trademark of General
Motors Corporation.
Loctite is a registered trademark of Henkel
Corporation, U.S.A.
LUBRIPLATE is a registered trademark of Fiske
Brothers Rening Co.
MERCON is a registered trademark of Ford
Motor Corp.
Never-Seez is a registered trademark of Bostik,
Inc.
Quintolubric is a registered trademark of
Quaker Chemical Corp.
Slic-tite is a registered trademark of LA-CO
Industries, Inc.
Spirolox is a registered trademark of Smalley
Steel Ring Company
Teon is a registered trademark of E. I. du
Pont de Nemours and Company.
Threadmate is a registered trademark of
Parker Intangibles LLC.
TRUARC is a trademark of TRUARC Co. LLC.
Vibra-Tite is a registered trademark of ND
Industries, Inc. USA.
.96
(2.4)
15.05
(38.2)
6.17
(15.7)
3.98
(10.1)
8.78
(22.3)
6.12
(15.5)
Ø
1.92
(4.9)
Ø
4°
HUCK
Specications

256 Pneudraulic Installation Tool (HK1015)
5
Preparation for Use
NOTE: WARNING Sticker and HUCK Trademark Sticker
must be in place and readable at all times.
GENERAL
1.Theefciencyandlifeofanytooldependsupon
propermaintenance.Regularinspectionand
correctionofminorproblemswillkeeptool
operatingefcientlyandpreventdowntime.The
toolshouldbeservicedbypersonnelwhoare
thoroughlyfamiliarwithhowitoperates.
2. Aclean,well-lightedareashouldbeavailablefor
servicingthetool.Specialcaremustbetaken
topreventcontaminationofpneumaticand
hydraulic systems.
3.Properhandtools,bothstandardandspecial,
mustbeavailable.
4.Allpartsmustbehandledcarefullyandexamined
fordamageorwear.AlwaysreplaceSeals,when
toolisdisassembledforanyreason.Components
should be disassembled and assembled in a
straightlinewithoutbending,cocking,orundue
force.Disassemblyandassemblyprocedures
outlined in this manual should be followed.
5.ServicePartsKit256KITincludesconsumable
partsandshouldbeavailableatalltimes.Other
components,asexperiencedictates,shouldalso
beavailable.
DAILY
1. If a Filter-Regulator-Lubricator unit is not being
used,uncoupleairdisconnectsandputafew
dropsofAutomaticTransmissionFluidorlight
oil into the air inlet of the tool. If the tool is in
continuoususe,putafewdropsofoilinevery
two to three hours.
2. Bleed the air line to clear it of accumulated dirt or
water before connecting air hose to the tool.
3.Checkallhosesandcouplingsfordamageorair
leaks,tightenorreplaceifnecessary.
4.Checkthetoolfordamageorair/hydraulicleaks,
tightenorreplaceifnecessary.
5. Check the nose assembly for tightness or
damage,tightenorreplaceifnecessary.
6.Checkoillevelintoolreservoir,replenishif
necessary.
WEEKLY
1. Disassemble and clean nose assemblies and
reassemble.
2.Checkthetoolandallconnectingpartsfor
damageoroil/airleaks,tightenorreplaceif
necessary.
TheModel256InstallationToolisshippedwithaplastic
plugintheairinletconnector.Theconnectorhas1/4-18
femalepipethreadstoaccepttheairhosetting.Quick
disconnectttingsand1/4”insidediameterairhoseare
recommended.Anairsupplyof90-100psicapableof22.4
CFMmustbeavailable.Airsupplyshouldbeequipped
withalter-regulator-lubricatorunit.
1. Removeplasticshippingplugfromairinletconnector
andputinafewdropsofAutomaticTransmission
Fluid,DEXRONIII,orequivalent.
2. ApplyTEFLONinstickformtothreadsofAirHose,and
screw hose into the tool.
3. Setairpressureonregulatorto90-100psi.
4. Screwairtting(notsuppliedwithtool)intoAirHose
andconnecttoairsource.Quickdisconnectttinginto
AirInletConnector,orscrewquickdisconnecttting
intoAirInletConnector,thenattachoptionalAirHose
suppliedwithtool.
5. Cycletoolafewtimesbydepressingandreleasing
trigger.
6. Disconnect air hose from tool.
7. Removeretainingnutandstop.
8. Selectpropernoseassemblyforfastenertobe
installed.
9. Screwcolletassembly,includinglockcollarandshim,if
applicable,ontospindleholdingHydraulicPullPiston
of tool with 3/8 hex key. Wrench tight.
10.Slidenoseassemblyanvilovercolletassemblyandinto
counterbore.
11.Slidetool’sStopandRetainingNutovernoseassembly
anvilandscrewNutontotoolhead.
12.Connectairhosetotoolandinstallfastener(s)ina
testplateofproperthicknesswithpropersizeholes.
Inspectfastener(s).
NOTE: Threadmate®should be used on collet threads
for nose assemblies without lock collars. All other
noses should be staked.
Caution:DonotuseTEFLONtapeonthreads.Use
onlyinstickform:HuckP/N503237.
WARNING: Inspect tool for damage or wear
before each use. Do not operate if damaged or
worn, as severe personal injury may occur.
Maintenance

256 Pneudraulic Installation Tool (HK1015)
6
Operating Instructions
LOCKBOLT® FASTENER INSTALLATION:
Placepininworkholeandplacecollaroverpin.See
WARNING.(IfCollarhasonlyonetaperedend,thatend
mustbefacingtowardtool,notnexttoworkpiece.)Hold
pinandpushnoseassemblyontopinprotrudingthrough
collaruntilnoseassemblyanviltouchescollar.Press
triggerandholdpresseduntilcollarisswagedandpintail
breaks. Release trigger and tool will go into return stroke.
The tool and nose assembly are ready for the next fastener
installation cycle.
BLIND FASTENER INSTALLATION:
Removeexcessgapfrombetweenthesheetstopermit
correct fastener installation. Tool and nose assembly must
beheldagainstworkpiece,andatarightangletoit.Press
triggerandholditpresseduntilfastenerisinstalledand
pintailbreaks.Releasetriggerandtoolwillgointoits
return stroke. The tool and nose assembly are ready for
next fastener installation cycle.
Failure to understand WARNINGS may cause serious personal injury. Failure to understand CAUTIONS may
cause damage to structure and Tool. For additional Safety Information, see page 4.
NOTE:Disassembleonlythosecomponentsnecessaryto
replacedamagedO-rings,Quadrings,Back-uprings,and
wornordamagedcomponents.Alwaysusesoft-jawvice
toavoiddamagetotool.
1.Disconnectairhosefromtoolandremovenose
assembly.
3.(Figure1)InsertFillToolthroughreservoirhousing
andscrewintoReservoirPlunger,lockingitintheout
position.
4.Unscrew4CapScrewswith5/32hexkey.Carefully
liftToolHeadstraightupfromHandle,andremove
PullandReturnGlandAssemblies.Removesealsfrom
glands.
5.UnscrewReliefValvePlugfromfrontofhead.Remove
ReliefValveSpring,Guide,Sleeve,andBall.Usinga
smallmagnetishelpful.
6.UnscrewReservoirFillPlug.Holdoverwasteoil
containerandreleaselltoolslowly.
7.UnscrewReservoirHousingfromhead.Remove2
Springs.SlideReservoirPlungerfromhead.Remove
spacerandQuadRing.Apickmaybeusedtoremove
the Quad Ring.
WARNING: Be sure air hose is disconnected
from tool before cleaning or performing
maintenance. Severe personal injury may occur
if air hose is not disconnected.
Reservoir
FillPlug
Reservoir
Plunger
Quad
Ring
Spacer
112465
Fill Tool
Assembly
Fill Tool in the
Lock-out position
Plug“A”
Screw“B”
4CapScrews
spring
Tool Head
Pintail
Deflector
HUCK
Check Va lve
Components
Reservoir
Housing
RETURNGland
Assembly
PULLGlandAssembly
Relief
Valve
Plug
Relief Valve Components
guide
ball
sleeve
2Springs
spring
guide
ball
plug
Cylinder
Cap
See also Fig. 10
(Plug“C”)
Figure 1
CAUTION: Do not scratch piston rod or cylinder
during removal. Use a plastic or wooden drift
to avoid damaging handle bore.
Disassembly Procedure
WARNING: Do not pull a fastener without a
collar. The fastener will eject with velocity
and force when the pintail breaks off. This
may cause serious injury.
WARNING: Do not pull a fastener without a
collar. The fastener will eject with velocity
and force when the pintail breaks off. This
may cause serious injury.
CAUTION: Remove excess gap from between
the sheets. This permits enough pintail to
emerge from collar for ALL jaw teeth to
engage with pintail. If ALL teeth do not engage
properly, jaws will be stripped/damaged.
CAUTION: To avoid structural and Tool
damage, be sure enough clearance is allowed
for nose assembly at full stroke. Do not abuse
the tool by dropping it, using it as a hammer
or otherwise causing unnecessary wear and
tear. Reasonable care of installation tools by
operators is an Important factor in maintaining
tool efciency and reducing downtime.

256 Pneudraulic Installation Tool (HK1015)
7
8. UnscrewCheckValvePlugfromsideofhead.Remove
CheckValveSpring,Guide,andBall.Asmallmagnetis
helpful.
9. IfCheckValveSeat(Figure10)isdamaged,contact
yourHUCKrepresentative.IfReliefValveSeatis
damaged,itcanberemovedasdescribedinstep10.
NOTE:Ifseatsareremoved,theymaynotbereused;
theymustbereplaced.
10. Relief ValVe Seat aSSembly RemoVal Note:Allpartsin
checkvalveholemustberemovedbeforePlug“A”
canberemoved.(Figs.1&10)UnscrewScrew“B”.
Inserta#10screwinthethreadofPlug“A”,andpull
toremove.Usingasmalldriftandhammer,fromrear
sideofhead,driveReliefValveSeatAssy(Fig.10)out
toward the front of the head.
11.PintailDeectorcanbepulledoffbarbedendatrear
ofHydraulicPullPiston.
12.UnscrewCylinderCapfromCylinder/Headusinga
1-3/4”open-endwrench.
13.(Fig.2)PlaceSpaceronHydraulicPullPiston,and
screwAssembly/DisassemblyBulletontopiston.Tap
orpresspistonassemblyoutofhead.This will push
out front and rear gland assemblies and wiper and
wiper housing.
14.(Fig.11)RemoveThrottleArmScrew;thenremove
ThrottleArm.PullThrottleValveoutofcylinder,and
removeSpring.
15.(Fig.10)Withasmallpunchandhammer,driveTrigger
PinfromtheHandle.RemoveCablePin.Removeball
endofCablefromThrottleArm(Fig.11),andpull
cable out of handle.
16.RemoveReservoirFillPlugfromhandle.(Fig.10)
17.(Fig.3)Holdtoolinvertedinvice.Unscrew3Cap
Screws with 5/32 hex key.
18. RemoveMuferEndCap,BottomExhaustGasket,
MuferandO-ring.
19. RemoveRetainingRingfromCylinderAssembly.Tap
Cylinder Head down into Cylinder Assembly for
easier removal of Retaining Ring.
20. ScrewCapScrewsintoCylinderHead,andcarefully
pryunderscrewstoremoveCylinderHead.(Figure3)
21. PushAirPistonallthewayintocylinderandlay
tool on its side. Hold Self-locking Nut with a 9/16
socketandextensionand,with7/64hexkey,unscrew
IntensierPistonScrew.
22. Turncylinderandhandleupsidedownandsecureina
vise.
23. GripSelf-lockingNutunderAirPistonwithpliersand
pullpistonandrodassemblyfromhandleandcylinder
assembly.
24. Witha13/8socketandextension,removeMain
Gland Assembly. Handle and cylinder will now
separate.
25. ToremovePolysealfromGlandAssembly,removethe
GlandAssemblyRetainingRingandSpacerrst.
26. Usingasoftdrift,pushIntensierPistonoutofhandle.
27. Toservicehandlesleeveandhandle,useablunt-
tippedpunchtogentlytapsleevefromtopofhandle
throughthebottom.Inspectsleevefordamageor
wear,andreplaceifnecessary.ServiceO-ringinside
handle bore.
Front Gland
Assembly
close-up
NOTE: Spacer must only be used for disassembly procedure
as it assists in pushing out Front Gland Assembly.
Note orientation
of polyseal
123111-1
Assembly
Bullet
123112-1
Spacer
HUCK
Figure 2
Muffler
EndCap
Bottom
Exhaust
Gasket
Muffler
O-Ring
Retaining
Ring
CapScrews
Use the screws
to pry out the
cylinder head. Cylinder
Head
Assembly
Press air
piston
and piston
rod fully into
the air
Self-locking
Nut
Main Gland
Assembly
IntensifierPiston
Assembly (Must be
unscrewed from
handle-side of
piston rod.)
PistonRod
AirPiston
Assembly
HandleSleeve
Handle O-ring
Figure 3
Disassembly Procedure continued

256 Pneudraulic Installation Tool (HK1015)
8
Cleancomponentswithmineralspiritsorsimilarsolvent.
Inspectforwear/damageandreplaceasnecessary.
Replaceallsealsofdisassembledcomponentsusing
ServicePartsKit,P/N256KIT.SmearLUBRIPLATE130AA
orPARKER-O-LUBEonringsandmatingpartstoease
assembly. Carefully assemble tool without damaging
O-rings,Quadrings,orBack-uprings.
1. (Figure4)InstallO-ringinsidehandle;thenpushsleeve
in handle until it bottoms on the chamfer.
2. Holdinghandleinvertedinavice,installtimingpin;
thenplaceaircylinderonhandlewithtimingpin
positionedinmatchinghole.AssembleMainGland
Assembly.Applyanti-seizecompound(p/n508183)to
glandthreads.Witha1-3/8inchsocketwrench,torque
it into the handle to 75-85 foot lbs.
3. Pushairpistonassemblyandpistonrodintoair
cylinderuntilitseatedinsideofaircylinder(Figure3).
4. Turntoolupright.AssembleIntensierPistonwith
O-RingandBack-upRings;thenapplyLoctite243to
intensierpistonscrewthreads,andcarefullypressin
fromtopofhandle.
5. Holding Self-locking Nut with 9/16 socket and
extension,screwintensierpistonontopistonrod
using7/64hexkey,andtorqueto180-190in.lbs.
6. Holdhandleinvisewithbottomup.PushCylinder
Head Assembly squarely into air cylinder. Install
Retaining Ring.
7. PositionO-RingandMuferoncenterofaircylinder.
PlaceBottomExhaustGasketonaircylinder.Place
MuferEndCapontopofGasket,andsecurewith3
CapScrewsusing5/32hexkey.
8. Turntoolupright.(Figure5)DropThrottleValveSpring
intoThrottleValveholeincylinder.PushThrottleValve,
withO-ringsinplace,intocylinder.
9. AssembleTrigger,Cable,andCablePin,andslideCable
into Handle. Align hole in Trigger with hole in Handle
andinstallTriggerPinwithahammerandpunch.
10. Slide Throttle Arm onto ball end of throttle cable.
Swingarmuntilendtsoverthrottlevalve.Attach
throttle arm Bushing and Screw to Throttle Arm.
Tighten with 5/32 hex key.
11.Ifairhoseassemblywasremoved,reinstallit.
12.IfReliefValveSeatAssyisbeingreplaced,pushPlug
“A”,withsealsinplace,intohead.InstallScrew“B”.
(Figure10)
13.CarefullydriveReliefValveSeatAssyinusingasoft
drift,withoutdamagingReliefValveBallsurface.
14.AssemblePullPistonwithnewseals.Lubricatewith
LUBRIPLATEorPARKERSUPER-O-LUBE.
15.ThreadAssemblyBulletontoPullPistonAssy.(Figure2)
NOTE:Spacernotneededduringassembly.Itspurpose
istopushoutthefrontglandduringdisassembly.
16.PushFrontGlandAssy,withallseals,Housing,and
Wiperinplace,overAssemblyBulletandontoPull
Piston.Pushentiregland/pistonassemblyintoHead.
17.(Figure10)InstallO-ringsandBack-upRingsonRear
GlandandpushcompleteassemblyintoHead.Screwin
CylinderCapandtighten.
18.(Figure10)InstallO-ring&Back-upRingonRelief
ValvePlug;theninstallBall,Guide,Sleeve,Spring,and
assembledReliefValvePlugintohead.
19. InstallO-ringonCheckValvePlug“D”,theninstall
Ball,Guide,Spring,andassembledCheckValvePlug
into head.
20.PushPintailDeectorontobarbedendofPullPiston.
21.(Figure10)PlaceO-ringsonBleedPlugs“C”&“E”and
screw assemblies into Handle and Cylinder Head.
22.(Figure10)InstallallO-ringsandBack-upRingsonPull
andReturnGlands.PushGlandAssembliesintohandle.
PushHeaddownonglands.
23.Placetoolinavise,headdown,andinstall4Cap
Screws,andproceedtoFill&Bleedsectionofthis
manual.
Assembly
Handle shown
partially
transparent
for clarity.
Chamfers of
sleeveand
handle meet
here
O-ring inside
grooveinhandle
Sleevepushed
infromtopof
handle
Figure 4
TriggerPin
CablePin
Cable Assembly
Throttle Arm
Guard Screw
(notshown)
Throttle Arm
Spring
ThrottleValve
with 3O-rings
inplace
Setscrew
Throttle Arm Guard
Throttle Arm
Bushing and Screw
Figure 5

256 Pneudraulic Installation Tool (HK1015)
9
EquipmentRequired:
-Shopairline90-100psimax.
- Air regulator
-FillBottle(Fig.7,suppliedwith
tool)
- Fill Tool 112465
-Largeatbladescrewdriver
- Stall Nut 120824
- Nose assembly
-Fasteners(Optional)
Preparation:
1. Installairregulatorinairline,
andsetpressureto20-40psi.
2. FillbottlealmostfullofDEXRONIII-ATF(automatic
transmissionuid).NOTE: Rell tool only when red line on
plunger drops below the red line on the reservoir housing
or when tool is rebuilt.
FORPARTSIDENTIFICATION,SEEFIGURES10AND11.
STEP1:ScrewFillToolintoReservoirPlunger,pullPlungerinto
ReservoirHousingandlockFillToolinfullforwardpositionby
tiltinghandle(longsidetouchingtool)andlockinginplace.
(Figure8)
STEP2:RemoveReliefandCheckValvePlugs,Guides,Springs
andBallsfromportsinhead.ReinstallPlugandSleeveinheadin
ReliefValveport(frontoftool).
STEP3: Screw retaining nut onto Head Assembly. Screw Stall
NutontoHydraulicPistonandtightentoensurefullthread
engagement. Back off Retaining Nut until it engages Stall Nut.
Check that Hydraulic Piston is all the way forward and locked with
Retaining Nut and with (or without) Stall Nut.
STEP4:AttachthetoolairsourcemomentarilytoseatAirPiston
atbottomofAirCylinder,thendisconnecttool.With Reservoir
Fill port facing up, lay tool on
its side.
STEP5: Install Fill Bottle in
ReservoirFillport.(Figure9)
STEP6:Connecttooltoshopair
20to40psi.Cycletool20-30
times,watchforairbubbles
escapingfromthetoolinto
bottle.(Youmayrockthetoolto
freetrappedairinthetool.)Do
not allow the air to re-enter the
tool.Whencyclingtool,alwaysholdbottleupasshowninFigure
10topreventdrawinginairfromemptypartofbottle.
STEP7:Whenairbubblesnolongerappearinbottle,removeFill
BottleandreplacetheReservoirFillPlugwhile tool is lying on
its side.
STEP8:InstalltheCheckValveBall,GuideandSpring.Replace
theCheckValvePlug.
STEP9:Turntoolsofrontofheadfacesyou.Priortoremoving
ReliefValvePlug,usinga3/32Allenwrench,backoutsetscrew
insideoftheplugapproximately1/2turncounterclockwise.
ThisensuresthatthePistonwillremaininfull-forwardposition.
RemovetheReliefValvePlug,installBall,Guide,Sleeveand
Spring,andreplacetheplug.
STEP10:UnlockFillToolandcheckReservoirredline.Cyclethe
tool the with Stall Nut attached and Retaining Nut locked in the
full-forwardposition(“DeadStall”).Reservoirshouldnotdrop
belowtheredlineontheReservoirhousing.
STEP11:Re-lockthelltool.Laytoolonitssideandremove
ReservoirFillPlug.TopoffReservoirbyplacingafewdropsof
oilinholeandwaitingforairbubblestoescape.Pushapinora
scribeintoholetocheckfortrappedairbubbles.ReplacePlug.
STEP12:UnlocktheFillToolandcycletoolasinstep10.
Reservoirmaydropslightly.Ifso,repeatstep11until,whenthe
FillToolhandleistouched,ithasnopressureagainstitandit
dropsoutofthelockposition,andtheReservoirPlungerdoes
notdropwhentooliscycled.NOTE:Thisusuallyrequires3to4
timestoppingoff.
STEP13:RemoveFillToolandStallNut.Installanoseassembly
andpullseveralfastenerstotestfunction.
WARNING: Avoid contact with hydraulic uid.
Hydraulic uid must be disposed of in accordance
with Federal, State and Local Regulations.
120337 Fill Bottle Assy
120336
Fill Bottle
120004Cap
Fill Point
Figure 7
WARNING: Air pressure MUST be set to 20 to 40 psi
to prevent possible injury from high pressure spray.
If Check Valve Plug is removed, Fill Bottle must be in
place before cycling tool.
(Check Valve port)
Install Fill Bottle here
Reservoir
FillPlug
CheckValvePlug
Relief
Valve
Plug
Red line indicator
120824 Stall Nut
112465 Fill Tool
(Shown in LOCK
position.)
Retaining Nut
Reservoir
Housing
Figure 8
Fill Bottle
shown in
Reservoir
Fill Port
Figure 9
Fill and Bleed
WARNING: Failure to re-lock Fill Tool will result in oil
being ejected from the head under pressure during
the topping off of the Reservoir. Severe personal
injury may result.

256 Pneudraulic Installation Tool (HK1015)
10
505864
Spring(2)
112403Housing/SpacerAssy
contains Housing 125546
and Spacer 123848 501408
QUADRing
112405Reservoir
Plunger
120129 Screw “B”
501082Back-upRing
502929 Ball
111067 Guide
100874Spring
120204Plug“A”
104293BleedPlugAssy“C”
508481 Setscrew
505446 O-Ring
111079BleedPlugAssy“D”
104293BleedPlugAssy“E”
117824
Retaining Nut
506160Polyseal
(Note orientation)
110670
Stop
130244
ThrottleLever(Trigger)
125643
Cable Assembly
130938Handle&
SleeveAssembly
505496CablePin
500621TriggerPin
126082 Front Gland Assy
(Gland not sold separately)
126087
PintailTube
505894
Wiper
114530Plug
501082Back-upRing
505446 O-Ring
505863Spring
120127Sleeve
120128 Ball Guide
505120
Relief
ValveBall 501082Back-upRing
505446 O-Ring
130254ReliefValveSeat&SealsAssembly
(Relief Valve Seat not sold separately.
Assemble/disassemble through front of head only) 501082Back-upRing
Check Valve Seat
(Reservoir Fill Plug)
(Relief Valve Plug)
(Check Valve Plug)
130267
Sleeve
508518
O-ring
123138
Wiper
Housing
130609 Hydraulic
PullPistonAssembly
(Piston not sold separately)
124209
Deflector
112491CylinderCap
(Torque to 36-66 ft. lbs.)
126086 Rear Gland Assembly
(Gland not sold separately)
113253Back-upRing
505887 O-Ring
129944Polyseal
(Note orientation)
126088Back-upRing
500823 O-Ring
113251
Back-upRing
500851 O-Ring
113251
Back-up
Ring
126098 Cylinder / Head
590517HUCKYearofMfrSticker 590240 WARNING Sticker*
*NOTE: Stickers must remain on tool and readable at all times. If stickers become
worn, damaged, or if they are missing, they must be ordered and replaced.
500101
Screw(4)
130244
ThrottleLever(Trigger)
500101
Screw(4)
SECTION A-A
Rotated 90° CCW
112502
Return Gland Assembly
500776
O-Ring
501084
Back-upRing
(Gland not sold
separately)
501082
Back-up
Ring
500778 O-Ring
500776
O-Ring
(Gland not sold
separately)
501082
Back-up
Ring
508518
O-Ring
131055
Pull Gland Assembly
AA
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
505864
Spring(2) 100874Spring
508481 Setscrew
114530Plug
(Relief Valve Plug)
Figure 10
Head/Handle Components

256 Pneudraulic Installation Tool (HK1015)
11
113526
AirPiston/
O-ring Assy
(Piston not sold
separately)
130305
PistonRod
501472
Quad Ring
121241
Self-locking Nut
113528 Cylinder
Head Assembly
(Cylinder not sold
separately)
505147
O-Ring
505139
Retaining
Ring
120076 MufflerEndCap
115554
Muffler
500777
O-Ring
500101
Screw(4)
126941-3 Gasket
116272 Throttle Valve Spring
104293 Bleed PlugAssembly
502482 Screw(2)
127029 Assembly (includes 507953 Throttle Arm Screw and 127028 Bushing)
127688
Throttle Arm
125657
Guard
127326 Gland Assembly
502821 Retaining Ring
500784 O-Ring
127324 Gland
500786 O-Ring
127327 Back-upRing
127329 Polyseal (note orientation)
500779 O-Ring
500781 O-Ring
127328
Back-upRing
127325 Gland Housing
590351*
Sticker
590350*
Sticker
590347
Sticker
130936 Intensifier
Piston Assembly
(Intensifier Piston not
sold separately)
501086
Back-upRing
501086
Back-upRing
503770 O-Ring
115436
Air Hose
115558 Throttle ValveAssembly (Valve not sold separately)
504407 O-Ring
504408 O-Rings
120372 Cylinder Assembly
502053 Setscrew
*NOTE: Stickers must remain on tool and readable at all times. If stickers become worn, damaged, or if they are missing, they must be ordered and replaced.
Figure 11
Air Cylinder Components

256 Pneudraulic Installation Tool (HK1015)
12
1 Toolfailstooperatewhentriggerisdepressed:
 a)Airlinenotconnected
 b)ThrottleValveO-ringswornordamaged.
 c)ThrottleValveCableisbroken.
2 Tooldoesnotcompletefastenerinstallationandbreak
pintail:
 a)Airpressuretoolow
 b)AirPistonQuadRingwornordamaged.
 c)Reservoiremptyorlow,refertoFillandBleed
section.
 d)Airinhydraulicsystem,refertoFillandBleed
section.
 e)ReservoirSpringswornordamaged
 f) Checkforpistondrift
3Pintailstrippedand/orswagedcollarnotejected:
 a)Checkforbrokenorwornjawsinnoseassembly,
refer to nose assembly data sheet.
 b)CheckforlooseRetainingNut
 c)Checkforpistondrift.
4Toolhaspistondrift:
 a)Loosecolletcrashingintothefrontoftheanvilcauses
thereliefvalvetoopenallowingthepistontodrift.
Tighten the collet and refer to Fill and Bleed section.
 b)WornordamagedReturnPressureReliefValvein
tool,inspectSeat,O-ring,Back-upRings,SteelBall
andValveSpring.Replaceifnecessary.
 c)WornordamagedIntensierPistonAssembly: 
InspectO-ringsandBack-upRings,andreplaceif
necessary.
5 Hydraulicuidexhaustswithairorleaksatbaseof
handle.
 a)WornordamagedGlandAssembly:InspectPolyseal,
O-rings,QuadRing,andBack-upRing,andreplaceif
necessary.
6. HydraulicuidleaksatrearofPullPiston
 a)WornordamagedRearGland:InspectO-ringsand
Back-upRings,andreplaceifnecessary.
7. HydraulicuidleaksatfrontofPullPiston.
 a)WornordamagedFrontGland:InspectPolyseal 
andreplaceifnecessary.
8.PullPistonwillnotreturn.
 a)ThrottleValvestuck:LubricateO-Rings.
 b)ThrottleArm,Cable,orTriggerbinding.
9. Air leaks at Air Cylinder Head.
 a)WornordamagedO-Ring.Replaceifnecessary.
Stroke Limiter - 118362-1
Reducesstroketo.750inches(1.91cm)
Stall Nut - 120824
PintailCollectionBag - 125655
ServiceToolKit  - 126104
Includes:
 PistonAssemblyBullet(Fig.2) -123111-1
 Spacer(Fig.2)  -123112-1
Troubleshooting
Accessories
Alwayscheckoutthesimplestpossiblecauseofamalfunctionrst.Forexample,anairhosenotconnected.Thenproceed
logically,eliminatingeachpossiblecauseuntilthecauseislocated.Wherepossible,substituteknowngoodpartsfor
suspectedbadparts.Usethissectionasanaidinlocatingandcorrectingmalfunction.
Note: “Pistondrift”iswhentheairpistonisinthedownposition,butthehydraulicpullpistonisnotinthefullforward
position.Thiscausesanoutofsequencecondition.

256 Pneudraulic Installation Tool (HK1015)
13
Limited Warranties
Limited Lifetime Warranty on BobTail® Tools:
HuckInternational,Inc.warrantstotheoriginalpurchaser
thatitsBobTail®installationtoolsmanufacturedafter
12/1/2016 shall be free from defects in materials and
workmanshipforitsuseful lifetime. This warranty does
notcoverspecialorder/non-standardproducts,orpart
failureduetonormalwear,toolabuseormisapplication,
orusernon-compliancewiththeservicerequirementsand
conditionsdetailedintheproductliterature.
Two Year Limited Warranty on Installation Tools:
HuckInternational,Inc.warrantsthatitsinstallationtools
manufactured after 12/1/2016 shall be free from defects in
materialsandworkmanshipforaperiodoftwoyearsfrom
dateofpurchasebytheenduser.Thiswarrantydoes
notcoverspecialorder/non-standardproducts,orpart
failureduetonormalwear,toolabuseormisapplication,
orusernon-compliancewiththeservicerequirementsand
conditionsdetailedintheproductliterature.
90 Day Limited Warranty on Nose Assemblies and
Accessories:
HuckInternational,Inc.warrantsthatitsnoseassemblies
and accessories shall be free from defects in materials
andworkmanshipforaperiodof90daysfromdateof
purchasebytheenduser.Thiswarrantydoesnotcover
specialclearancenoses,orspecialorder/non-standard
product,orpartfailureduetonormalwear,abuseor
misapplication,orusernon-compliancewiththeservice
requirementsandconditionsdetailedintheproduct
literature.
Useful lifetimeisdenedastheperiodoverwhichthe
productisexpectedtolastphysically,uptothepoint
whenreplacementisrequiredduetoeithernormal
in-servicewear,oraspartofacompleteoverhaul.
Determinationismadeonacase-bycasebasisupon
returnofpartstoHuckInternational,Inc.forevaluation.
Tooling, Part(s) and Other Items not manufactured by
Huck:
HUCKmakesnowarrantywithrespecttothetooling,
part(s),orotheritemsmanufacturedbythirdparties.
HUCKexpresslydisclaimsanywarrantyexpressed
orimplied,astothecondition,design,operation,
merchantability,ortnessforuseofanytool,part(s),or
otheritemsthereofnotmanufacturedbyHUCK.HUCK
shallnotbeliableforanylossordamage,directlyor
indirectly,arisingfromtheuseofsuchtooling,part(s),
or other items or breach of warranty or for any claim for
incidental or consequential damages.
Huck shall not be liable for any loss or damage resulting
fromdelaysornon-fulllmentofordersowingtostrikes,
res,accidents,transportationcompaniesorforany
reason or reasons beyond the control of the Huck or its
suppliers.
Huck Installation Equipment:
HuckInternational,Inc.reservestherighttomake
changesinspecicationsanddesignandtodiscontinue
models without notice.
HuckInstallationEquipmentshouldbeservicedbytrained
servicetechniciansonly.
Alwaysgivetheserialnumberoftheequipmentwhen
correspondingororderingserviceparts.
CompleterepairfacilitiesaremaintainedbyHuck
International,Inc.Pleasecontactoneoftheofceslisted
below.
Eastern
OneCorporateDriveKingston,NewYork12401-0250
Telephone(845)331-7300FAX(845)334-7333
OutsideUSAandCanada
ContactyournearestHuckInternationallocation(see
reverse).
Inadditiontotheaboverepairfacilities,thereare
AuthorizedToolServiceCenters(ATSC’s)located
throughouttheUnitedStates.Theseservicecentersoffer
repairservices,spareparts,ServicePartsKits,Service
ToolKitsandNoseAssemblies.PleasecontactyourHuck
RepresentativeorthenearestHuckInternationallocation
(seereverse)fortheATSCinyourarea.

Arconic Inc. (NYSE: ARNC) creates breakthrough products that
shape industries. Working in close partnership with our customers,
we solve complex engineering challenges to transform the way we
fly, drive, build and power.
Through the ingenuity of our people and cutting-edge advanced
manufacturing, we deliver these products at a quality and efficiency
that ensures customer success and shareholder value.
Arconic Fastening Systems and Rings world-wide locations:
AMERICAS
Kingston Operations
1 Corporate Drive
Kingston, NY 12401
800-278-4825
845-331-7300
FAX: [phone]
Carson Operations
900 Watson Center Rd.
Carson, CA 90745
800-421-1459
310-830-8200
FAX: [phone]
Waco Operations
PO Box 8117
8001 Imperial Drive
Waco, TX 76714-8117
800-388-4825
254-776-2000
FAX: [phone]
Tucson Operations
3724 East Columbia
Tucson, AZ 85714
800-234-4825
520-747-9898
FAX: [phone]
Acuña Operations
Hidalgo #120
Parque Industrial Amistad
26220 Acuña Coahuila
Mexico
FAX: [phone]
TELEX: 1173530 LUKSME
EUROPE
Telford Operations
Unit C, Stafford Park 7
Telford, Shropshire
England TF3 3BQ
01952-290011
FAX: [phone]
Us Operations
BP4
Clos D’Asseville
95450 Us par Vigny
France
33-1-30-27-9500
FAX: [phone]
AUSTRALIA
Melbourne Operations
11508 Centre Road
Clayton, Victoria
Australia 3168
03-764-5500
Toll Free: 008-335-030
FAX: [phone]








Huck is Forever, For the Long Haul, The Future
of Fastening Technology, The Future of Assembly
Technology, The Future of Tooling Technology,
and Tools of Productivity are service marks of
Huck International. Huck provides technical
assistance regarding the use and application of
Huck fasteners and tooling.
NOTICE: The information contained in this
publication is only for general guidance with
regard to properties of the products shown
and/or the means for selecting such products,
and is not intended to create any warranty,
express, implied, or statutory; all warranties are
contained only in Huck’s written quotations,
acknowledgments, and/or purchase orders. It
is recommended that the user secure specific,
up-to-date data and information regarding each
application and/or use of such products.
© 2017 Huck International, Inc. www.afsrhuck.net/us
1 Corporate Drive, Kingston, NY 12401 • Tel: [phone] • Fax: [phone]