Milwaukee TSS 1000 User manual

Cat. No.
TSS 1000
FOLDING TABLE SAW STAND
OPERATOR'S MANUAL
To reduce the risk of injury, user must read and understand operator's manual.
WARNING

2
SPECIFIC SAFETY RULES
TABLE SAW STAND
WARNING
Read all safety warnings and all
instructions provided with the ta-
ble saw stand and the table saw to be mounted.
Failure to follow the warnings and instructions may
Save all warnings and instructions for future
reference.
•Disconnect the battery pack from the table saw
before making any adjustments or changing
accessories. Accidental starting of the power tool
is a cause of some accidents.
•Properly assemble the table saw stand before
mounting the tool. Proper assembly is important
to prevent risk of collapse.
•Securely fasten the table saw to the table saw
stand before use. Table saw shifting on the table
saw stand can cause loss of control.
•
surface. If the table saw stand can shift or rock, the
table saw or workpiece cannot be safely controlled.
•Do not overload the table saw stand or use as
Overloading or standing on
the table saw stand causes the stand to be “top-
heavy” and likely to tip over.
•
•Avoid dangerous environments. Use your tool stand
•Keep work area clean and well lit. Cluttered, dark
work areas invite accidents.
•
.
•Maintain control. Keep proper footing and balance at
all times.
•Maintain table saw stand carefully. Keep table saw
stand dry, clean and free from oil and grease. Follow
instructions for changing accessories. Periodically
inspect table saw stand for damage and wear.
•
•Keep bystanders away. Children and bystanders
should be kept at a safe distance from the work area
to avoid distracting the operator.
•To reduce the risk of injury, always wear eye pro-
tection.
•Fingers can be pinched between the legs of the
table saw stand. To reduce the risk of injury, keep
fold.
•Always use common sense and be cautious
when using tools. It is not possible to anticipate
every situation that could result in a dangerous out-
come. Do not use this tool if you do not understand
these operating instructions or you feel the work is
beyond your capability; contact Milwaukee Tool or
a trained professional for additional information or
training.
ASSEMBLY
WARNING
Properly assemble the table saw
stand before mounting the tool.
Proper assembly is important to ensure stability.
Legs must match with corresponding number
indicators on the stand.
Assembling the Stand
1
1
1
1
2
2
3
3
Indicators
35 mm
Bolt & Nut
60 mm Bolt,
Spacer, & Nut
Adjustable
Foot & Nut
1. Insert the legs into the frame according to the in-
dicator stickers. Mismatched leg/frame assembly
will cause the frame to wobble.
2.
Insert the 35 mm bolt through the frame/legs as-
sembly and thread on the nut. Use a 6 mm hex
wrench and 17 mm open end wrench to securely
tighten.
3.
Assemble the frame pieces together, placing the
plastic washer between the frame sections.
4.
Insert the 60 mm bolt through the frame assembly
and thread on the nut. Use a 6 mm hex wrench
and 17 mm open end wrench to securely tighten.
5.
Screw the nut onto the adjustable foot.
6.
7. Screw in the adjustable foot into the stand until the
stand sits level. Turn the nut back until it contacts
the frame, locking the adjustable foot in place.
Use only with MILWAUKEE®Table Saws
M18FTS210, and mount securely, according to
these instructions. Improperly installed Table
Saws can cause injury or property damage.
The table saw stand weight limit is 82kg. If more
than 82kg is placed on the table saw stand it may
be damaged and may cause personal injury.
Maintain labels. These carry important
information. If unreadable or missing, contact a
MILWAUKEE®service facility for a replacement.
Insert the narrower frame into the wider frame at
an angle to fit the crossbeam through, then
straighten to align the bolt holes (see picture).

3
Installing the Table Saw
1
2
3
Rear
Brackets
Latch
Tab
1. Hook the back of the saw into the rear brackets.
2. Lower the front of the saw onto the frame.
3. Secure the latch onto the saw's front tab.
WARNING
Properly level the table saw stand
before each use. If the table saw
stand can shift or rock, the table saw or work-
piece cannot be safely controlled.
Leveling
1. Loosen the locking nut.
2. Screw in or out the foot to level the stand.
3.

WARRANTY - AUSTRALIA and NEW ZEALAND
AUSTRALIA AND NEW ZEALAND
MILWAUKEE®Service
MILWAUKEE®prides itself in producing a premium quality product that is Nothing But Heavy Duty®.
Your satisfaction with our products is very important to us! If you encounter any problems with the
operation of this tool, please contact your authorised MILWAUKEE®dealer.
For a list of MILWAUKEE®dealers, guarantee or service agents please contact MILWAUKEE®
Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 361 505)
(New Zealand Toll Free Telephone Number 0800 279 624) or visit www.milwaukeetools.com.au /
www.milwaukeetools.co.nz.
Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to
product sold in Australia and New Zealand.
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Tool (Australia)
21 Kelletts Road, Rowville, VIC 3178
Melbourne, Australia
Milwaukee Tool (New Zealand)
2 Landing Drive, Mangere
Auckland, 2022, New Zealand
Designed by Milwaukee Electric Tool Corp.
Professionally Made in China for Milwaukee Tool (Australia) / Milwaukee Tool (New Zealand)
Printed in China