MiniFinder PICO User manual

- 1 -
USER GUIDE
minifinder pico
Copyright © MiniFinder 2015
www.minifinderpico.com

- 2 -
1. Product Overview
Thank you for buying MiniFinder Pico. This mini-sized device is created on latest positioning technology such as built-in u-Blox GPS
chipset and SIMCOMM GSM/GPRS technology. Popular purpose is monitoring and protecting of valuables, lone workers, children,
elderly, people with dementia disease and others.
Latest technology and design
Unique design, combination of style and usability
Supports A-GPS for accelerated positioning
Supports GPS and Cellular tracking
Two way voice communications
Emergency alarm button
Fall detection via 3D G-sensor
Built-in 8MB flash memory
GPRS blind area data re-upload function

Copyright © MiniFinder 2015
- 3 -
2. Getting Start
2.1 Hardware and Accessories
Product box includes:
Device
USB-cable
2.2 Product overview

- 4 -
2.3 Hardware Functions
GREEN LED
The device is connected to GSM network
Flashing every 0.2 second on and 3 seconds off
The device is connected to GPRS network
Flashing two times fast and 3 seconds off
The device is not connected to GSM network
Flashing every 1 second on and 3 seconds off
Without SIM card
GSM LED Solid
BLUE LED
The device has GPS positioning fix
Flashing every 0.2 seconds on and 3 seconds off
The device has GSM positioning fix
Flashing every 1 second on and 3 seconds off
The device has no GPS fix
Flashing every 2 seconds on and 3 seconds off
GPS chip sleeping
No flashing
RED LED
Solid
The device is charging
OFF
The device is off or has been full charged
Flashing randomly
The device is on the move
Buttons
Power On/Off button
To turn on/off the device, press and hold for 3 seconds. LED lamps will start blinking.
SOS button
When pressed fast 3 times, it will send SMS alarm to all numbers and call the numbers.
Call button
When pressed for 3 seconds, It will start to call the B1 number
Other Connectors
Micro USB
Used for charging and firmware upgrade
Microphone
Used for listen in and voice communication
Speaker
Used for Two way voice communication

- 5 -
Usage
-For the first time, please fully charge the battery for about 8 hours.
-When charging, the Power LED will be ON (solid). After fully charged, the power LED will be off.
-Insert an activated Micro SIM card and turn on the unit by pressing the on/off button for 3 seconds.
-Please keep the unit under the open sky or close the window to be able to get a fix on the satellites.
3. Setup the Authorized Numbers
※It is not mandatory for all three of the authorized numbers to be set, however a minimum of one must always be set.
Set up the 3 authorized mobile phone numbers to track the unit.
①Command:A1
Note: With no spaces in the text, case-insensitive.
※Using your mobile phone, send A1 to the SIM card phone number in the device, it will reply you a message: ·Set mobile number 1 OK!
※To delete this number from stored memory, you can send A0 to the tracker.
②Command:B1
The device will reply you a message: ·Set mobile number 2 OK!
※To delete this number from stored memory, you can send B0
③Command:C1
The device will reply you a message:·Set mobile number 3 OK!
※To delete this number from stored memory, you can send C0

www.minifinder.com
Copyright © MiniFinder 2014
- 6 -
4. Modify the Time zone
Command: TZ++00/-00
Note: the time must amounts be in 2 digits and at maximum 23 hours in value. “+” in the “time zone” portion of the text indicates east. The symbol “-“ in the
“time zone” indicates west.
Example: tz+02, the system will add 2 hours based on the UTC time.
tz-02, the system will minus 2 hours based on the UTC time.
※UTC time has been set as default time.
5. User defined name in SMS
Command: NAME1, name
Example: NAME1,Emma, the tracker will reply “Add name ok!”
※To delete name, you can send NAME0
6. Location request
6.1 Reply with coordinates and web link.
Command: LOC
The device will reply “GPS Info! Time: xxxxx; Lat: xxxx; Lon: xxxx; Spd: xxxxx, Altitude:xxxx Bt: xxx
maps.google.com/maps?q=loc: 59.325783,18.077954
※Put coordinates to Google earth or Google maps. Click on search button, then you will find the position fixed.
※Click on the link then the location can be shown directly on Google Map on your mobile phone.

- 7 -
6.2 Reply with Address.
Command: ADD
Notes: This function needs GPRS function support!
The device will reply “Add: Storgatan 35, Stockholm, Sweden;
7. Cell Locate
※The unit can be tracked by GSM base station tower, If GPS signal is not available for example in room, underground etc, user can be located by GSM tower.
However, as compared to GPS satellite, GSM accuracy is proven to be worse than that of GPS. GSM provider utilizes triangulation techniques to try to
pinpoint the location of the device, and GSM base station is further affected by factors similar to GPS in the sense of the barriers affecting signal quality and
the density of GSM towers to assist in the triangulation effort, with some regional areas having errors of 100M-2KM!
Command: CL1
The device will reply “Cell locate on!
To turn off this function, please send CL0
8. GEO-FENCE Alarm
Command: G+X, Y, Z, xxxM/KM
Example: G1,1,1,100M
Notes: No space in between.
X=No. Of Geo fence (1~3), user can set 3 Geo fences
Y=0 means to turn off the function Y=1 means to turn on the function
Z=1 means to set alarm when the tracker enters the preset area
Z=0 means to set alarm when the tracker breaches the district
xxx is the preset distance to the tracker’s original place, must be 3 digitals. M means meters, KM means kilometers
The device will send the message to the authorized numbers as “Geo fence alarm!+GPS info” when it enter the area you set.
(User must set this function when tracker already fixed GPS signal)

- 8 -
To turn off this function, please send G1,0 or G2,0 or G3,0
9. Over-Speed alert
Command: SPEED1,+ SPEED
Notes: The speed must be in value of speed and in 2 or 3 digitals. (01~255km/h)
Example: speed1,100
Suppose the over-speed alert that we want to set is 100km/h, when the device moves exceeds 100km/h, it will send message “Over-speed! +GPS Info” to all
preset numbers.
To turn off this function, please send SPEED0 to the device.
10.GPS signal lost and recovery alert
Command: GR1
The device will automatically send the latest available GPS information to the preset numbers when it enters into the area without GPS signal.
If user goes into an area that does not have a GPS signal, such as a tunnel, cave, parking garage, etc. –the device will know where user was 10 minutes before
they went into such an area. This is critical! If a child goes missing –you’ll be able to know the closest possible location before the GPS signal was lost.
With any SMS sent during the period without GPS signal, the device will reply GPS information to preset numbers soonest as the GPS signal is covered.
To turn off this function, please send GR0

- 9 -
11. Movement Alert
Command: M1, xxxM/KM
Notes: xxx is the preset distance to the tracker’s original place, must be 3 digitals. M means meters, KM means kilometers
Example: m1,100m
When the tracker moves out of 100 meters, it will send SMS alarm to the preset numbers.
To turn off this function, please send M0 to the device.
12. Listen-in
Command: L1
Only A1, B1, C1 number can make a silence call to the tracker, the track answers the call automatically and allows the caller to listen to what happens around
the tracker. There is no voice indication that the call is in progress.
To turn off this function, please send L0 to the device.
13.Vibration alarm
Command: V1, xx S/M/H
Note: No space in between, S means second, M means minute, H means hour, xx means the time you set and must be two digitals.
Example: V1,05M
If user turns on this function, device will detect motion every 5 minutes and will send SMS alarm to all registered phone numbers for warning.
To turn off this function, please send V0
14.Switch off LED lights
Command: LED1
The device will reply “LED off”and later LEDs will stop flashing, but device is actually running.
To turn off this function, please send LED0

- 10 -
15. AGPS
Command: AGPS1
A-GPS is for accelerated positioning and helping position a device when GPS signals are weak or not available. GPS satellite signals may be impeded by tall
buildings, and do not penetrate building interiors well. A-GPS uses proximity to cellular towers to calculate position when GPS signals are not available.
To turn off this function, please send AGPS0
16. Fall detection
Command: FL1
Device will reply “fall detection on”and will send alarm to all registered phone numbers if detect fall.
A simple fall may cause a devastating consequence. A Fall Sensor can help you get immediate help without missing any important moment.
To turn off this function, please send FL0
17. Smart Power saving mode
Command: PS1
Device built-in motion sensor. Under this mode, GSM chip always on, GPS chip activates by motion or incoming call or SMS, GPS chip off when its no motion
or calling or SMS. You won't waste any battery life when device isn't moving.
Under normal use, battery can last 4 ~ 10 days.
To turn off this function, please send PS0
18. Deep Sleeping mode
Command: DS1
Both GSM and GPS chip will be off to save power, it can be only activated by motion sensor. Once it activated by motion, it will running for 15 minutes and
sleep again if no motion detected.
Battery can last 40 days if no motion at all.

- 11 -
To turn off this function, please send DS0
19. Check preset mobile phone numbers & status
Command: STATUS
The device will reply E.g. A+4673812345678 B73912345678 C73712345678; Spd: 0,100km/h; Geo:0,0,0; VB:1,10S; MV:1,100; LBS:1; LED:0; RCV:0; TZ:2.0;
Lis-in: 1; PS:1; DS:0; FL:1; Bat: 95
To recognize the meaning of “0”& “1”
The number “0” implies that the function is turned off; whilst “1” indicates that the function is turned on.
20. SOS Button
Once the SOS button is pressed 3 times under 2 seconds, the GSM light will dim for 2 times and SOS Alarm "Help me! + GPS info!" will be sent to the
authorized phone number and Website. In the mean time, it will dial 3 authorized numbers every 30 seconds. The first number will take priority over the
second, the third one. If the tracker fails connect to the first number, it will switch to the second one, In case the second number fail to be connected too, the
system will connect to the third number etc, this will go on and on until one of the telephone pick up, then two ways communication starts.
21. Call Button
Press Call button for 3 seconds, the GSM light will dim for 2 times and the tracker will dial the first number.
22. How to adjust Sound Volume:
Pressing the side button VOL+\ VOL- to adjust the volume when in two way voice communication.
23. Low battery alarm:
Note: When the tracker’s battery is lower than 20%, it will send a SMS alarm “BAT: LOW! + GPS INFO” to all preset numbers.

- 12 -
24.Real time tracking via www.tracktor.se
Our web based tracking system incorporates the TCP/IP protocol and allows users to monitor it in real time over the internet via computer or cell phone.
24.1 GPRS Settings:
In order to use the GPRS function, the user needs to setup the APN by sending SMS command.
--What is APN? Access point name (APN) is the name used to identify a general packet radio service (GPRS) bearer service in the GSM mobile network. The
APN defines the type of service that is provided in the packet data connection.
※Make sure that the SIM card in the tracker supports the GPRS function.
※The APN can be acquired from your local GSM operators.
Command: S1, APN, user name, password
Notes: Some access point name without user name and password, so please leave it blank.
Example: S1,internet
“internet” is the APN from the SIM card provider; therefore the user must set their particular APN for their own country which the unit resides.
After sending the command, the device will reply “Set APN OK! GPRS connecting”
24.2 Disable GPRS:
Command: S0
The device will reply “GPRS OFF”.
24.3 Reconnect GPRS
Reconnect the website via GPRS for real time tracking, please send S2
24.4 Set GPRS Time interval by SMS
Command: TIxxS/M/H

- 13 -
The meaning of “xx”, The setting must be in 2 digitals and maximum 99 in value, which means 01~99.
xxS is the time interval in second with range(30~99)
xxM is the time interval in minute with range(01~99)
xxH is the time interval in hour with range(01~99)
Example: TI01M
The device will reply “Set updating time interval OK!”and then device will update the time by every 1 minute on the website.
24.5 Check APN & VPN or IP
Command: G1
The device will reply “APN: internet; Name: xxx; Password: xxxx; Port: 20790; VPN or IP:www.tracktor.se”
25.Get IMEI and Version number
Command: VERSION
The device will reply” IMEI: xxxx; GSM CSQ:xxxx; Soft: V072.4601.1435”
26. Change IP and Port
Command: IP1,IP,port
Example: IP1,111.22.33.11,20790
27. Reboot Device
Command: REBOOT
The device will restart itself without changing any settings.

- 14 -
28. Initialization
Command: RESET!
Note: This is to make all settings back to the factory default.
29. Built-in Memory
The device built in 8MB flash memory inside. It will store the GPS information when do not have GSM network coverage (i.e., very low population density
areas, some mountainous terrain, underground areas etc). The device will transmit GPS locations to the WEB server automatically once the GSM network is
recovered.
Cautions:
Please comply with the instructions to extend the unit life:
1. Keep the unit dry. Any liquid may destroy or damage the inside circuitry.
2. Do not use & store the unit in dusty places.
3. Do not put the unit in overheated or overcooled places.
4. Clear the unit with a piece of dry cloth. Don’t clean in chemicals, detergent.
5. Do not disassemble or refit the unit.

- 15 -
Technical specification:
Content
Specification
Mainframe Dimension
60mm*41mm*16mm
Weight
35g
GSM Frequencies
900/1800mhz or 850/1900Mhz
GPS chip
U-blox 7 (Made in Switzerland)
GPS sensitivity
Cold start: -148dBm Hot start: -162dBm
GPS accuracy
<2.5m
Time to First Fix
Cold start 32s, Warm start 11s, Hot start 1s
Charging Voltage
5V DC
Battery
Chargeable 3.7V 900mAh
Standby Current
≤2mAh
Storage Temperature
-40°C to +85°C
Operation Temperature
-20°C to +80°C
Humidity
5%-95% non-condensing