MINN KOTA MAXXUM Bowmount bowGuard 360 User manual

Feature Information
Installation
Operation
Adjustments
Cautions
Battery Information
Circuit Breaker
Battery Connection
Wiring Diagram
Propeller Replacement
Maintenance
Trouble Shooting
Limited Warranty
pg. 2
pg. 3
pg. 4
pg. 5
pg. 6
pg. 7
pg. 7
pg. 8
pg. 9
pg. 10
pg. 10
pg. 10
pg. 11
bowmount
bowGuARD 360°®
foot contRoL
tRoLLInG motoR
serial number
purchase date
CE Master User Manual for MAXXUM
NOTE: Do not return your Minn Kota motor to your retailer. Your
retailer is not authorized to repair or replace this unit. You may
obtain service by:
•calling Minn Kota at 1-800-227-6433 or 1-507-345-4623;
•returning your motor to the Minn Kota Factory Service Center;
•sending or taking your motor--- to any Minn Kota authorized
service center on enclosed list.
Please include proof of purchase, serial number and purchase
date for warranty service with any of the above options.
PLeAse thoRouGhLy ReAD thIs useR mAnuAL. foLLow ALL InstRuctIons AnD heeD ALL sAfety & cAutIonARy notIces beLow. use
of thIs motoR Is onLy PeRmItteD foR PeRsons thAt hAve ReAD AnD unDeRstooD these useR InstRuctIons. mInoRs mAy use thIs
motoR onLy unDeR ADuLt suPeRvIsIon.

Lifetime Warranty
Composite Shaft
BowGuard 360o
Breakaway Protection
Mom/Off/Con
Switch
Heel Block
Rugged Die Cast
Aluminum and
High Strength Steel
Bracket
Weedless Wedge™ Propeller
Permanent Magnet
Cool Power™ Motor
Momentary
Switch
Rotary
Speed
Control
FEATURE INFORMATION
2
Specifications subject to change without notice.
Depth Collar Knob
Lighted Direction
Indicator

InstALLAtIon
3
Position the Bowmount close to the centerline of
the boat and in an area free of obstructions.
cAutIon: mAKe suRe youR motoR Is mounteD on A LeveL suRfAce.
InstALLAtIon of the bowmount:
We recommend that you have another person help with this procedure.
1. For installation, do not remove the shaft/motor from the Bowguard. The Bowguard spring is under ten-
sion and must always remain secured.
2. Place the mount, with the motor in the fully retracted (flat) position, on the deck of the boat:
• The motor should be mounted as close to the centerline of the boat as possible.
• Make sure bow area under the chosen location is clear and unobstructed for drilling.
• Make sure the motor rest is positioned far enough beyond the edge of the boat. The motor, as it is low-
ered into the water or raised into the boat, must not encounter any obstructions.
3. Once in position, mark four (4) of the holes provided in the bow plate and drill through the marks using a
(9/32”) bit.
4. Mount the plate to the bow through the four (4) drilled holes using the provided (1/4-20x3-1/2”) bolts,
nuts and washers.
note: If possible, secure all sets of mounting bolts, nuts and washers.

bow mount oPeRAtIon:
The bowmount is designed to fold back and lock the motor flat on the deck when not in use and to provide
secure stowage for transport.
• The pull rope releases the lock bar, which automatically engages when the unit is lowered or raised into
position. The pull grip and rope should be used to both lower and raise the unit.
• The motor rest positions the lower unit as it comes in contact with the nose of the mount and guides it
onto the motor rest.
wARnInG : when RAIsInG oR LoweRInG motoR, KeeP fInGeRs
cLeAR of ALL hInGe AnD PIvot PoInts AnD ALL movInG PARts.
cAutIon:
swItch the mom / off / con contRoL to off when not In use. If
the motoR contRoL Is Left on AnD the PRoPeLLeR RotAtIon Is
bLocKeD, seveRe motoR DAmAGe cAn ResuLt.
foot PeDAL contRoL oPeRAtIon:
Most of the controls in the remote foot pedal are easy to operate by either foot or hand:
• ROTARY SPEED CONTROL. These motors offer a choice of five speed settings. Turn the knob clock-
wise to increase speed and counter-clockwise to decrease speed.
• MOM / OFF / CON SWITCH. When depressed to CON, the “constant on” allows you to run continu-
ously without keeping your foot on the pedal. Depress the switch MOM for momentary operation or to
OFF.
• MOMENTARY SWITCH. With the MON / OFF / CON set to “MOM”, a toe touch on the “momentary”
switch turns the motor on. Let up and the motor stops.
• RIGHT/LEFT. Push the toe end of the foot rest down to turn right and push the heal end of the foot rest
down to turn left. Watch the indicator on the motor head to check direction.
• FORWARD/REVERSE. The motor always drives forward by depressing the constant on or momentary
switch. You can reverse the direction of thrust by turning the motor 180°.
wARnInG: WHEN INCLUDED WITH MOTOR, THE VELCRO STRAP AND STABILIzER MUST
BE USED WHEN MOTOR IS IN THE STOWED POSITION.
FAILURE TO INSTALL AND USE THESE SUPPLIED PARTS MAY RESULT IN DAMAGE TO THE
MOTOR NOT COVERED BY THE PRODUCT WARRANTY.
oPeRAtIon
4

ADJustments
5
DePth ADJustment:
• Firmly grasp the outer shaft or control head and hold it
steady.
• Loosen the depth setting knob until the shaft slides freely.
• Raise or lower the motor to the desired depth.
• Turn the motor control head to the desired position.
• Tighten depth setting knob to secure the motor in place.
note: When setting the depth be sure the top of the motor
is submerged at least 12” to avoid churning or agitation
of surface water. The propeller must be completely sub-
merged.
Depth Setting Knob
cAbLe ADJustment:
The steering cable tension is pre-set at the factory
but will, through normal use, need occasional
adjustment. Adjust the length and tension by turn-
ing the Phillips/hex head screw located near the
bottom of the foot pedal, just under the steering
cable cover.
Turn the screw clockwise to increase tension and
counter-clockwise to decrease tension.
note: If the cable becomes too loose it may disen-
gage for either the roller drum in the control box
or the pulley in the foot pedal.
Cable Tension Adjustment
Screw
Cable Pulley
Stainless Steel Cable

6
CAUTIONS
6
Attention:
•Avoid running your motor with the propeller outside of the water. This may result in injuries from the rotating
propeller.
•It is recommended to set the speed selector to zero and place the motor in the deployed position prior to con-
necting power cables. Disconnect power cables prior to stowing.
•Always ensure that the power cables are not twisted or kinked; and that they are securely routed to avoid a
safety or trip hazard. Ensure cables are unobstructed in all locations to avoid damaging the wire insulation.
Damage to the insulation could result in failure or injury.
•Always inspect the insulation of the power cables prior to use to ensure they are not damaged.
•Disregarding these safety precautions may result in an electrical short of the battery(s) and/or motor. Always
disconnect the motor from the battery(s) before cleaning or checking the propeller.
•Avoid submerging the complete motor as water may enter the lower unit through control head and shaft.
Water in the lower unit may cause an electrical short and damage the lower unit. This damage will not be
covered by warranty.
Caution!
•Always operate the motor in a safe distance away from obstructions. Never approach the motor when the
propeller is running. Contact with a spinning propeller may endanger you or others.
•Always exercise safe practices when using your motor; stay clear of other watercrafts, swimmers, and any
floating objects. Always obey water regulations applicable to your area of operation.
•Never operate the motor while under the influence of alcohol, drugs, medication, or other substances which
may impair your ability to safely operate equipment.
•This motor is not suitable for use in strong currents exceeding the thrust level of the motor.
The constant noise pressure level of the motor during use is less than 70dB(A). The overall vibration level does
not exceed 2,5m/sec≈.

BATTERY INFORMATON CIRCUIT BREAKER
7
BOAT RIGGING AND MOTOR INSTALLATION:
An over-current protection device (circuit breaker or fuse) must be used with this motor. Coast Guard
requirements dictate that each ungrounded current-carrying conductor must be protected by a manually reset,
trip-free circuit breaker or fuse. The type (voltage and current rating) of the fuse or circuit breaker must be
sized accordingly to the trolling motor used. The following breaker sizes are recommended guidelines:
Maximum thrust Voltage Recommended circuit breaker rating
30# to 45# 12V 50A @ 12VDC
50# to 55# 12V 60A @ 12VDC
65# to 70# 24V 50A @ 24VDC
80# 24V 60A @ 24VDC
101# 36V 50A @ 36VDC
E-Drive 48V 40A @ 48VDC
The appropriate wire size needed to connect your trolling motor to the trolling motor batteries varies depend-
ing on the length of cable needed and voltage of the motor. For additional information, please consult appro-
priate ABYC (American Boat and Yacht Council) and Coast Guard requirements.
Reference:
United States Code of Federal Regulations: 33 CFR 183 – Boats and Associated Equipment
ABYC E-11: AC and DC Electrical Systems on Boats
BATTERY INFORMATION:
The motor will operate with any deep cycle marine 12 volt battery/batteries. For best results use a deep cycle,
marine battery with at least a 115 ampere hour rating. As a general on the water estimate, your 12 volt
motor will draw one ampere per hour and your 24 volt motor will draw .75 ampere per hour for each pound
of thrust produced when the motor is running on high. The actual ampere draw is subject to your particu-
lar environmental conditions and operation requirements. Maintain battery at full charge. Proper care will
ensure having battery power when you need it, and will significantly improve the battery life. Failure to
recharge lead-acid batteries (within 12-24 hours) is the leading cause of premature battery failure. Use a
variable rate charger to avoid overcharging.
If you are using a crank battery to start a gasoline outboard, we recommend that you use a separate deep
cycle marine battery/batteries for your Minn Kota trolling motor.
Advice regarding batteries:
Never connect the (+) and the (–) terminals of the battery together. Take care that no metal object can
fall onto the battery and short the terminals. This would immediately lead to a short and utmost fire
danger.
Recommendation: Use battery boxes and covered battery terminal clamps like Minn Kota accessory #MK-
BC-1.

5
BATTERY CONNECTION
8
BATTERY CONNECTION:
The motor will operate with any deep cycle marine 12
volt battery/batteries. For best results use a deep
cycle, marine battery with at least a 115 ampere
hour rating. As a general on the water estimate,
your 12 volt motor will draw one ampere per hour
and your 24 volt motor will draw .75 ampere per
hour for each pound of thrust produced when the
motor is running on high. The actual ampere draw
is subject to your particular environmental condi-
tions and operation requirements. Maintain battery
at full charge. Proper care will ensure having bat-
tery power when you need it, and will significantly
improve the battery life. Failure to recharge lead-
acid batteries (within 12-24 hours) is the leading
cause of premature battery failure. Use a variable
rate charger to avoid overcharging.
If you are using a crank battery to start a gasoline
outboard, we recommend that you use a separate
deep cycle marine battery/batteries for your Minn
Kota trolling motor.
Advice regarding batteries:
Never connect the (+) and the (–) terminals of the
battery together. Take care that no metal object
can fall onto the battery and short the terminals.
This would immediately lead to a short and
utmost fire danger.
Recommendation: Use battery boxes and covered
battery terminal clamps like Minn Kota accessory
#MK-BC-1.
24 Volt System:
1. Two 12 volt batteries are required.
2. The batteries must be wired in series, as
directed in wiring diagram to provide 24 volts.
A. Connect a connector cable to positive ( +
) terminal of battery 1 and to negative ( – )
terminal of battery 2.
B. Connect the positive (+) red lead from the
foot pedal to the positive (+) terminal on bat-
tery 2.
C. Connect the negative (–) black lead to the
negative (–) terminal of batt ery 1.

w
Y
AB
R
+
MOMENTARY SWITCH

MOM/OFF/CON SWITCH

FIVE SPEED SWITCH

TERMINAL 
BLOCK

MOTOR

BLACK -

WHITE CONNECTING WIRE

BLUE CONNECTING WIRE

WHITE 
BLACK- 
BLACK-

BLACK 
RED+ 
RED+

YELLOW 
INDICATOR LIGHT

CONNECTING WIRE
BATTERY 1 BATTERY 2

wARnInG:
• BeforeconnectingBattery,makesurethe 
mom-off-con swItch on the foot PeDAL Is In
the off PosItIon.
• keepleadwireconnectiontightandsolidto
the bAtteRy teRmInALs.
• locateBatteryinaventilatedcompartment.
wIRInG DIAGRAm
9
Over-Current Protection Devices not shown in illustrations.

PRoP RePLAcement mAIntenAnce tRoubLeshootInG
10
PRoPeLLeR RePLAcement:
• Disconnect motor from battery prior to changing the pro-
peller.
• Hold the propeller and loosen the prop nut with a pli-
ers or a wrench.
• Remove prop nut and washer. If the drive pin is
sheared/broken, you will need to hold the shaft
steady with a screwdriver blade pressed into the
slot on the end of the shaft.
• Turn the old prop to horizontal (as illustrated) and
pull it straight off. If drive pin falls out, push it back
in.
• Align new propeller with drive pin.
• Install prop washer and prop nut.
• Tighten prop nut 1/4 turn past snug. [ 25-25 inch
pounds ]. Be careful, over tightening the prop nut
can damage the propeller.
Prop Nut
Drive Pin
Slot End
Weedless Propeller
Prop Washer
cAutIon:
mAKe suRe motoR Is DIsconnecteD fRom bAtteRy befoRe beGInnInG Any PRoP woRK oR mAInte-
nAnce.
mAIntenAnce:
1. After use, these units should be rinsed with fresh
water, then wiped down with a cloth dampened with
silicone spray. This motor is not equipped for salt
water exposure.
2. The propeller must be cleaned of weeds and fishing
line. The line can get behind the prop, wear away the
seals and allow water to enter the motor. Check this
after every 20 hours of operation.
3. Before each use, check to see that the prop nut is
secure.
4. To prevent accidental damage during trailering or
storage, disconnect the battery whenever the motor
is off of the water. For prolonged storage, lightly coat
all metal parts with an aqueous based silicone spray.
5. For maximum performance, restore battery to full
charge before each use.
6. Keep battery terminals clean with fine sandpaper or
emery cloth.
7.The weedless wedge propeller is designed to provide
absolute weed free operation with very high effi-
ciency. To maintain this top performance, the leading
edge of the blades must be kept smooth. If an edge
is rough or nicked from use, restore to smooth by
sanding with fine sandpaper.
tRoubLeshootInG:
1. Motor fails to run or lacks power:
• Check battery connections for proper polarity.
• Make sure terminals are clean and corrosion free.
Use fine sandpaper or emery cloth to clean termi-
nals.
• Check battery water level. Add water if needed.
2. Motor loses power after a short running time:
• Check battery charge, if low, restore to full charge.
3. Motor is difficult to steer:
• Check steering cables for proper tension. Adjust as
necessary.
4. Prop vibration during normal operation:
• Remove and rotate the prop 180°. See removal
instructions in prop section.
note: For all other malfunctions, see enclosed autho-
rized service center listing for nearest service center.

Composite Shaft
Johnson Outdoors Marine Electronics, Inc. warrants to the
original purchaser that the composite shaft of the purchas-
er’s Minn Kota® trolling motor is free from defects in mate-
rials and workmanship appearing within the original pur-
chaser’s lifetime. Johnson Outdoors Marine Electronics,
Inc. will provide a new shaft, free of charge, to replace any
composite shaft found to be defective more than two (2)
years after the date of purchase. Providing such a new
shaft shall be the sole and exclusive liability of Johnson
Outdoors Marine Electronics, Inc. and the sole and exclu-
sive remedy of the purchaser for breach of this warranty;
and purchaser shall be responsible for installing, or for the
cost of labor to install, any new composite shaft provided
by Johnson Outdoors Marine Electronics, Inc.
Entire Product
Johnson Outdoors Marine Electronics, Inc. warrants to the
original purchaser that the purchaser’s entire Minn Kota®
trolling motor is free from defects in materials and work-
manship appearing within two (2) years after the date of
purchase. Johnson Outdoors Inc. will, at its option, either
repair or replace, free of charge, any parts, including any
composite shaft, found to be defective during the term of
this warranty. Such repair or replacement shall be the sole
and exclusive liability of Johnson Outdoors Marine
Electronics, Inc. and the sole and exclusive remedy of the
purchaser for breach of this warranty.
Terms Applicable to Both Warranties
These limited warranties do not apply to motors used com-
mercially or in salt water, nor do they cover normal wear
and tear, blemishes that do not affect the operation of the
motor, or damage caused by accidents, abuse, alteration,
modification, misuse or improper care or maintenance.
DAMAGE TO MOTORS CAUSED BY THE USE OF
REPLACEMENT PROPELLERS OR OTHER REPLACE-
MENT PARTS NOT MEETING THE DESIGN SPECIFICA-
TIONS OF THE ORIGINAL PROPELLER AND PARTS
WILL NOT BE COVERED BY THIS LIMITED WARRANTY.
The cost of normal maintenance or replacement parts
which are not defective are the responsibility of the pur-
chaser.
To obtain warranty service in the U.S., the motor or part
believed to be defective, and proof of original purchase
(including the date of purchase), must be presented to a
Minn Kota® Authorized Service Center or to Minn Kota®’s
factory service center in Mankato, MN. Any charges
incurred for service calls, transportation or shipping/freight
to/from the Minn Kota® Authorized Service Center or facto-
ry, labor to haul out, remove, re-install or re-rig products
removed for warranty service, or any other similar items
are the sole and exclusive responsibility of the purchaser.
Motors purchased outside of the U.S. (or parts of such
motors) must be returned prepaid with proof of purchase
(including the date of purchase and serial number) to any
Authorized Minn Kota® Service Center in the country of
purchase. Warranty service can be arranged by contacting
a Minn Kota® Authorized Service Center listed on the
enclosed sheet, or by contacting the factory at 1-800-227-
6433, 1-507-345-4623 or fax [phone]. Note: Do not
return your Minn Kota® motor or parts to your retailer. Your
retailer is not authorized to repair or replace them.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN
THESE LIMITED WARRANTIES. IN NO EVENT SHALL
ANY IMPLIED WARRANTIES (EXCEPT ON THE COM-
POSITE SHAFT), INCLUDING ANY IMPLIED WAR-
RANTIES OF MERCHANTABILITY OR FITNESS FOR
PARTICULAR PURPOSE, EXTEND BEYOND TWO
YEARS FROM THE DATE OF PURCHASE. IN NO
EVENT SHALL JOHNSON OUTDOORS MARINE ELEC-
TRONICS, INC. BE LIABLE FOR INCIDENTAL, CONSE-
QUENTIAL OR SPECIAL DAMAGES.
Some states do not allow limitations on how long an
implied warranty lasts or the exclusion or limitation of inci-
dental or consequential damages, so the above limitations
and/or exclusions may not apply to you. This warranty
gives you specific legal rights and you may also have other
legal rights which vary from state to state.
LIMITED LIFETIME WARRANTY ON COMPOSITE SHAFT,
LIMITED TWO-YEAR WARRANTY ON ENTIRE PRODUCT:
“WARNING: This product contains chemical(s) known to the state of California to cause cancer and/or reproductive toxicity.”
wARRAnty
11

22
12
3
4
5
67
89
10
11
12
13
14
15
16
17
18
20
21
23
24 25
19
26
5
139
91
150
153
155
157
151
152
30
28
27
29
36
38
39
40
41
32
33
42
45
46
47 48
49
51
52
53
148
62
149
67
67
68
69
70
72
77
78
80
76
85
87
88
120
118
125
131
121
117
119
61
44
35
37
65
60
55
56
57
64
59
133
147
43
111
50
54
66
58
84
132
138
142
143
144
145
146
79
81
133
134
92
90
103
105
94
96
93
95
127
128 124
123
129
97
100
98
102
10199
122
108
112
106
83
82
109
110
126
107
115
136
137
116
141
31
158
74
75
73
71
135
200
205
PARTS DIAGRAM
MAX 70/SC
70 lbs Thrust
24 Volt
42” SHAFT
This page provides MinnKota® WEEE compliance disassembly instructions. For more
information about where you should dispose of your waste equipment for recycling and
recovery and/or your European Union member state requirements, please contact your
dealer or distributor from which your product was purchased.
Tools required but not limited to: Flat Head screw driver, Phillips screw driver, Socket
set, Pliers, wire Cutters.

PARTS LIST
2-100-119 ARMATURE ASSEMBLY 24V 3.625 5SPC 65# 788-015 RETAINING RING 140-010 BALL BEARING 431-005 CENTER HOUSING ASSEMBLY 3.625 FW TXT 2-300-039 BRUSH END HOUSING ASSEMBLY 3.62 SPCO 2-400-101 PLAIN END HOUSING ASSEMBLY 144-049 BEARING - FLANGE (SERVICE ONLY) 880-003 SEAL 880-006 SEAL WITH SHIELD 188-037 BRUSH ASSEMBLY [2.EA] 725-050 BRUSH RETENTION- PAPER TUBE 738-036 BRUSH PLATE W/HOLDER 975-040 SPRING - TORSION [2.EA] 337-036 GASKET 701-008 O-RING, THRU-BOLT [2.EA] 701-081 O-RING 2888460 SEAL & ORING KIT 830-007 SCREW-8-32 [2.EA] 830-008 THRU-BOLT 10-32x9.2” [2.EA] 990-067 WASHER- STEEL THRUST 990-070 WASHER - NYLATRON [2.EA] 2096035 MOTOR ASSEMBLY 24V 3.625 5SPC FW 52” 2032003 TUBE (COMP) 4 HOLE-42” 1378131 PROP KIT 2091160 PROPELLER (W.WEDGE 2) 2151726 WASHER-5/16 STD SS 2053101 NUT-PROP,NYLOC (MED) 5/16 SS 2092600 PIN-DRIVE (95-4HP’S) SS 9008236 WASHER 1/4 FLAT ZINC [4.EA] 2223100 NUT- TENSION 5/16-18 SS [2 .EA] 2262605 PIN- BWGRD UPPER THREADED 2262607 CLEVIS PIN ZP MAXXUM BWGRD 2260805 SPRING CLIP 2150400 PULL-GRIP 2151700 WASHER-EYE SHAFT(.562 OD) 2991840 MOUNT, BOW ASS, W/O BGRD, FW STD 2264241 ARM-UPPER FW,STD 2293501 BUSHING, STAINLESS STEEL [4.EA] 2263500 BOLT- SHOULDER (MAxxUM) [2.EA] 2994307 ARM-LOWER ASSEMBLY,STD,FW,EXT 2263912 MOTOR REST STD MAXXUM 2265514 DECAL-MAxxUM,MOTOR REST [2.EA] 2261505 SPACER, MOTOR REST [6.EA] 2773987 BOWPLATE,STD FW-MACH/INSERT 2251601 ROPE (40”), MAXXUM MOUNT 2261708 WASHER-3/8x1/2x.010” SS [2.EA] 2267318 BEARING NYLINER-[2.EA] 2263434 SCREW, 8-18 x 1” PPH SS [2.EA] 2152610 SPRING-PIN LOCKBAR [2.EA] 2233600 LOCK BAR- BOW MOUNT 2233602 LOCK BAR, REAR - ZINC 2152700 SPRING-LOCKBAR CAD.PLTD 2262703 SPRING STOP 2153602 EYE SHAFT-2LOCKBAR STD-PL
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
n
17 18 19 20 21 22
n
23 24 25 26 27 28 29 30 31 32 33
n
35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
2260506 HINGE-PIN HEADLESS ZINC 2293811 YOKE,MAX MNT-POLYPROPYLENE 2991762 BOWGUARD ASSEMBLY 2772319 BRACKET BASE TOP/EYELET ASSEMBLY
2991771 BRKT BTTM/BEARING FW ASSEMBLY 2772352 EYELET KIT 2263423 SCREW 5/16-18 X 1” SHCS ZINC 2263425 SCREW 5/16-18 x 2 1/2” SHCS [2.EA] 2071541 SPRING-SLEEVE UPPER 2071535 SPRING SLEEVE, LOWER 2262706 SPRING, BOWGUARD, NIK PL 2772012 TUBE W/BEARING RACE ASSEMBLY 2772016 TUBE W/BEARING RACE ASSEMBLY 2272069 TUBE OUTER-21” 4 HOLES 2272067 TUBE OUTER -24” 4 HOLES 2266260 BEARING RACE 2266220 BEARING RACE-STEEL 2266000 BEARING BALL-STEEL [2.EA] 2266115 BEARING CONE 2771617 COLLAR HALF-ZINC- 2 PER KIT 2263452 SCREW-1/4-20 x 3/4” SHCS [2.EA] 2280201 CONTROL BOX COVER 2372100 SCREW-8-18 x 5/8” THD SS [4.EA] 2275603 DECAL-COVER MAX70/SC 2990140 DIRECTIONAL INDICATOR 2282730 SPRING-INDICATOR 2375400 SHRINK TUBE-1/4OD x 1-3/4” [2.EA] 2053414 SCREW-#8-32 x 1/2” TRI-LOBE [3.EA] 2267800 GEAR-INDICATOR 2372100 SCREW-8-18 X 5/8” SS 2264019 LIGHT/INDICATOR MAX65/SC 2020713 TERMINAL-ADAPTOR, MAx [2.EA] 2335400 SHRINK TUBE-1/2 OD x 2” [2.EA] 2052511 CABLE CLAMP, 1/4” VANTAGE 2232360 PULLEY-CABLE DRUM . 2261730 WASHER-NYLON A/T CON B 2996247 PINION/RACE ASSEMBLY 2223468 SCREW-8-32 x 7/16” ZN PL [4.EA] 2994496 FOOT PEDAL/PLUG ASSEMBLY (AT) 2283700 PUSH-BUTTON FOOT PEDAL 2302732 SPRING-LOWER PEDAL SS 2264020 SWITCH MOMENTARY 2265140 BOOT-MICROSWITCH 2262114 SCREW-MOUNTING/SWITCH [2.EA] 2233100 NUT-SWITCH MOUNT [2.EA] 2264026 SWITCH-5 SPEED (ALL TERRAIN) 2261701 LOCKWASHER-STAR 2263105 NUT-HEX 2261715 SPACER-SWITCH 5 SP MODELS 2280110 KNOB-SPEED CONTROL (5 SPD) 2263000 E-RING TRU-ARC#5133-43 2260730 CONNECTOR 1/4 MALE TAB OD 2332103 SCREW-6-20 X 3/8” THD SS 2266413 TENSION SCREW PLATE FTPED
53 54
n
55 56 57 58 59 60 61 62
n
64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 87 88 90 91 92 93 94 95 96 97 98 99
100 101 102 103 105 106
2260511 PIN-PIVOT A/T FT PDL 2774550 FT PED BASE/PIN ASSEMBLY 2262301 PULLEY- FOOT PEDAL 2266401 COVER-PULLEY STAMPING 2223430 SCREW- #8 x3/4 SS PPH TYPE 25 [4.EA] 2254031 SWITCH-M0M/OFF/CON 2266412 SWITCH PLATE, FT PEDAL 2332103 SCREW-6-20 x 3/8 THD SS [2.EA] 2261208 WIRE HARNESS, A/T FT. PHD 2267505 CABLE ASSY-RIGHT (5’) 2267515 CABLE ASSY-LEFT (5’) 2265430 CABLE JACKET (5’)
2265110 BOOT-CONTROL BOX 2265115 BOOT-FOOT PEDAL BASE 2372100 SCREW-8-18 x 5/8 THD SS [2.EA] 2261714 WASHER-MAxxUM FT PDL [2.EA] 2261901 BRACKET-CONDUIT 2301310 SCREW-8-18 x 1/2 SS [2.EA] 2263210 BRACKET-CONDUIT ADJUSTMEN 2263104 NYLOCK KEEPER 2263463 SCREW-1/4-20 X 2” STL PPH 2261225 LEADWIRE 24V 10GA. RING 2256300 TIE WRAP-5.5” BLACK 2263201 CLAMP WIRE HARNESS MICRO [2.EA] 2332103 SCREW-6-20 X 3/8 THDT SS 2260301 CONNECTING WIRE (SWITCH) 2260312 WIRE,BLK W/WHT STRP 19 1/2 2260322 WIRE,BLK W/BLUE STRP-12” 2256301 TIE WRAP-5.5” WHITE 2266414 BOTTOM PLATE MAX FOOT PED 9953104 SCREW-8 x 1/2” SS [8.EA] 2282500 CONTROL BOX 2267800 GEAR-INDICATOR [2.EA] 2262221 INDICATOR-DRIVE 2261905 BRACKET/INDICATOR 2301310 SCREW-8-18 X 1/2” SS 2994830 BAG ASSEMBLY-MAXXUM 2263431 SCREW 1/4-20 x 3.5” PPH [6.EA] 2261713 WASHER-1/4 FLAT SS [6.EA] 2263103 NUT-1/4-20 NYLOCK-JAM SS [6.EA] 2991550 CLAMP COLLAR ASSEMBLY
2071550 CLAMP COLLAR “A” 2071555 CLAMP COLLAR “B” 2072621 PIN-KNURLED 2281505 KNOB-CLAMP COLLAR 2071718 WASHER #10 NYLON RETAINING 2073102 NUT - HEX 1/4 - 28 SS 2071560 SPLIT COLLAR 2075120 URETHANE PAD 2261540 INSERT-THREADED BOWPLATE (2 EA)
107 108 109 110 111 112 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 131 132 133 134 135 136 137 138 139 141 142 143 144 145 146
n
*147 *148 *149
n
150 151 152 153 155 157 158 200 205
* This item is part of an assembly. This item cannot be sold separately due to machining and /or assembly that is required. P/N 2274958 REV. L ECN 32961 2-11
In the U.S.A., replacement parts may be ordered directly from MINN KOTA Parts Dept., 121 Power Drive, P.O.Box 8129, Mankato, Minnesota 56002-8129. In Canada, parts may be ordered from any of the Canadian Authorized Service Centers shown on the enclosed list. Be sure to provide the model and serial numbers of your motor when ordering parts. Please use the correct
part numbers from the parts list. Payment for any parts ordered from the MINN KOTA parts department, may be by cash, personal check, Discover Card, MasterCard or VISA. To order, call 1-800-227-6433 or FAX [phone].
Hors de États-Unis, voir la liste ci-jointe pour le Centre de Service Agréé MlNN KOTA le plus proche. Lors d’une commande, ne pas oublier de fournir le numéro de modèle et le numéro de série du moteur. Toujours mentionner le numéro de pièce exact figurant sur la liste des pièces de rechange.
PARTS LIST

Minn Kota accessories
available for your motor.
Visit our website at www.minnkotamotors.com
Portable Chargers
Stabilizer Kits
OnBoard Chargers
Circuit Breakers
Quick Release Brackets
Quick Plugs
© 2010 Johnson Outdoors Marine Electronics, Inc. p/n 2267153 REV. H ECN 33016 3-11
ENVIRONMENTAL COMPLIANCE STATEMENT:
It is the intention of Johnson Outdoors Marine Electronics, Inc. to be a responsible corporate citizen, operating in compliance with
known and applicable environmental regulations, and a good neighbor in the communities where we make or sell our products.
WEEE Directive:
EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive (WEEE)” impacts most distributors, sellers, and
manufacturers of consumer electronics in the European Union. The WEEE Directive requires the producer of consumer electron-
ics to take responsibility for the management of waste from their products to achieve environmentally responsible disposal during
the product life cycle.
WEEE compliance may not be required in your location for electrical & electronic equipment (EEE), nor may it be required for EEE
designed and intended as fixed or temporary installation in transportation vehicles such as automobiles, aircraft, and boats. In
some European Union member states, these vehicles are considered outside of the scope of the Directive, and EEE for those
applications can be considered excluded from the WEEE Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the product must not be disposed of with other household refuse. It must be
disposed of and collected for recycling and recovery of waste EEE. Johnson Outdoors Marine Electronics,
Inc. will mark all EEE products in accordance with the WEEE Directive. It is our goal to comply in the collec-
tion, treatment, recovery, and environmentally sound disposal of those products; however, these requirement
do vary within European Union member states. For more information about where you should dispose of your
waste equipment for recycling and recovery and/or your European Union member state requirements, please
contact your dealer or distributor from which your product was purchased.
Disposal:
Minn Kota motors are not subject to the disposal regulations EAG-VO (electric devices directive) that implements
the WEEE directive. Nevertheless never dispose of your Minn Kota motor in a garbage bin but at the proper place of collection of
your local town council.
Never dispose of battery in a garbage bin. Comply with the disposal directions of the manufacturer or his representative and dispose
of them at the proper place of collection of your local town council.