MINN KOTA Riptide Ulterra User manual

RIPTIDE ULTERRA™
BOW-MOUNT TROLLING MOTOR
Installation Instructions

2 | minnkotamotors.com ©2019 Johnson Outdoors Marine Electronics, Inc.
INTRODUCTION
Made by Minn Kota
Johnson Outdoors
Marine Electronics, Inc.
121 Power Drive
Mankato, MN 56001 USA
Trolling Motors
Produced in 2015
SER NO R365 MK12345
RT_ULTERRA 80/IP-54"_BT
MODEL 1358955
EXAMPLE
NOTICE: The serial number on your Riptide Ulterra is
located underneath the bracket.
THANK YOU
Thank you for choosing Minn Kota. We believe that you should spend more time fishing and less time positioning your boat. That’s why
we build the smartest, toughest, most intuitive trolling motors on the water. Every aspect of a Minn Kota trolling motor is thought out
and rethought until it’s good enough to bear our name. Countless hours of research and testing provide you the Minn Kota advantage
that can truly take you “Anywhere. Anytime.” We don’t believe in shortcuts. We are Minn Kota. And we are never done helping you
catch more fish.
Model Serial Number:
Controller Serial Number:
Purchase Date:
Store Where Purchased:
REGISTRATION
Remember to keep your receipt and immediately register
your trolling motor. A registration card is included with your
motor or you can complete registration on our website at
minnkotamotors.com.
SERIAL NUMBER
Your Minn Kota 11-character serial number is very important. It
helps to determine the specific model and year of manufacture.
When contacting Consumer Service or registering your product,
you will need to know your product’s serial number. We
recommend that you write the serial number down so that you
have it available for future reference.
NOTICE: Do not return your Minn Kota product to your retailer. Your retailer is not authorized to repair or replace this unit. You
may obtain service by: calling Minn Kota at [phone]; returning your product to the Minn Kota Factory Service Center;
sending or taking your product to any Minn Kota authorized service center. A list of authorized service centers is available on our
website, at minnkotamotors.com. Please include proof of purchase, serial number and purchase date for warranty service with any
of the above options.
MOTOR INFORMATION (For Consumer Reference Only)

minnkotamotors.com | 3
©2019 Johnson Outdoors Marine Electronics, Inc.
SAFETY CONSIDERATIONS
Please thoroughly read the user manual. Follow all instructions and heed all safety and cautionary notices. Use of this motor
is only permitted for persons that have read and understood these user instructions. Minors may use this motor only under
adult supervision.
WARNING
You are responsible for the safe and prudent operation of your vessel. We have designed your Minn Kota product to be an accurate
and reliable tool that will enhance boat operation and improve your ability to catch fish. This product does not relieve you from the
responsibility for safe operation of your boat. You must avoid hazards to navigation and always maintain a permanent watch so you can
respond to situations as they develop. You must always be prepared to regain manual control of your boat. Learn to operate your Minn
Kota product in an area free from hazards and obstacles.
WARNING
Never run the motor out of the water, as this may result in injuries from the rotating propeller. The motor should be disconnected from
the power source when it is not in use or is off the water. When connecting the power-supply cables of the motor to the battery, ensure
that they are not kinked or subject to chafe and route them in such a way that persons cannot trip over them. Before using the motor
make sure that the insulation of the power cables is not damaged. Disregarding these safety precautions may result in electric shorts
of battery(s) and/or motor. Always disconnect motor from battery(s) before cleaning or checking the propeller. Avoid submerging the
complete motor as water may enter the lower unit through control head and shaft. If the motor is used while water is present in the
lower unit considerable damage to the motor can occur. This damage will not be covered by warranty.
WARNING
Take care that neither you nor other persons approach the turning propeller too closely, neither with body parts nor with objects. The
motor is powerful and may endanger or injure you or others. While the motor is running watch out for persons swimming and for floating
objects. Persons whose ability to run the motor or whose reactions are impaired by alcohol, drugs, medication, or other substances are
not permitted to use this motor. This motor is not suitable for use in strong currents. The constant noise pressure level of the motor
during use is less than 70dB(A). The overall vibration level does not exceed 2,5 m/sec2.
WARNING
It is recommended to only use Johnson Outdoors approved accessories with your Minn Kota motor. Using non-approved accessories
including to mount or control your motor may cause damage, unexpected motor operation and injury. Be sure to use the product and
approved accessories, including remotes, safely and in the manner directed to avoid accidental or unexpected motor operation. Keep all
factory installed parts in place including motor and accessory covers, enclosures and guards.
WARNING
When stowing or deploying the motor, keep fingers clear of all hinge and pivot points and all moving parts. In the event of unexpected
operation, remove power leads from the battery.

4 | minnkotamotors.com ©2019 Johnson Outdoors Marine Electronics, Inc.
KNOW YOUR BOAT
Keel
Bow
Hull
Bow
Stern
Stern
Port
Port Starboard
Starboard
Gunwale
Gunwale
Transom
Inboard
Outboard

minnkotamotors.com | 5
©2019 Johnson Outdoors Marine Electronics, Inc.
INSTALLATION
8
9
14
13
11
12
5
6
7
19 20 18 17
1
16
3
4
2
10
AA
BB
CC
Item /
Assembly Part # Description Qty.
1✖MOTOR ASSEMBLY 1
AA
Includes
2-7
2994917 BAG ASSY, ULTERRA MTG HARDWARE 1
2 2203430 SCREW-1/4-20 X 2.0 HHCS SS 6
3 2203431 SCREW-1/4-20 X 0.5 HHCS SS 6
4 2201725 WASHER-CLIPPED, 1/4", 1.00" OD 6
5 2261713 WASHER-1/4 FLAT 18-8 SS 6
6 2263103 NUT-1/4-20 NYLOCK SS 6
7 2301720 WASHER-MOUNTING - RUBBER 6
8 2994075 tREMOTE ASSEMBLY, iPILOT 1
9 2994076 ÂREMOTE ASSEMBLY LINK TOUCHSCREEN 1
p2397101 tMANUAL, QUICK REF., iPILOT 1.6 1
p2397103 ÂMANUAL-QUICK REF., iPILOT 3.0 1
10 2390800 tÂLANYARD, REMOTE W/ CARABEENER 1
11 2373241 ÂCABLE, USB REMOTE CHARGER LINK 1
12 2375901 ÂADAPTER, USB DC POWER LINK 1
13 2996400 tÂHEADING SENSOR ASSEMBLY 1
14 490389-1 ÂCABLE, ETH (M12-M-M12-F, 30' 1
16 2203801 STRAP, HOLD DOWN 1
BB 1378132 80# THRUST PROP KIT 1
CC 1378160 112# THRUST PROP KIT 1
17 2341160 PROP-WW2 (4.5) w/ADP.RING 1
2331160 PROP-WW2 (4") w/ADP.RING 1
18 2262658 PIN-DRIVE 1" X 3/16" S/S 1
19 2091701 WASHER-PROP (LARGE) 1
20 2093101 NUT-PROP, NYLOC, LG, MX101 3/8 SS 1
p2207114 MANUAL, INSTALL GUIDE, RT ULTERRA 1
p2394900 INSTRUCTIONS, HEADING SENSOR 1
INSTALLING THE RIPTIDE ULTERRA
Your new Riptide Ulterra comes with everything you’ll need to directly install it to the boat. This motor can be directly mounted to the
boat or it may be coupled with a Minn Kota quick release bracket for ease of mounting and removal. For installation with a quick release
bracket, refer to the installation instructions provided with the bracket. For compatible quick release mounting brackets and to locate
your nearest dealer, visit minnkotamotors.com. To install the motor directly to the boat, please follow the instructions provided in this
manual. Please review the parts list, mounting considerations and tools needed for installation prior to getting started. For additional
product support, please visit minnkotamotors.com.
INSTALLATION PARTS LIST
pNot shown on Parts Diagram.
✖This part is included in an assembly and cannot be ordered individually.
tOnly available with models factory installed with i-Pilot.
ÂOnly available with models factory installed with i-Pilot Link.

6 | minnkotamotors.com ©2019 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE RIPTIDE ULTERRA
It is recommended that the motor be mounted as close to the keel or centerline of the
boat as possible. Make sure the area under the mounting location is clear to drill holes
and install nuts and washers. Make sure the motor rest is positioned far enough beyond
the edge of the boat. The motor must not encounter any obstructions as it is lowered into
the water or raised into the boat when stowed and deployed. Consider a quick release or
adapter bracket with the installation of your motor. To view a list of accessories, please visit
minnkotamotors.com.
a. Place the Motor on an elevated, level surface such
as a workbench or the tailgate of a pickup. The
motor, as removed from the box, should be in the
stowed position.
b. Remove the four sideplate screws using a #3 or #2
Phillips screwdriver. Two of these screws will be
located on each side of the Motor Mount.
c. Remove the Right Sideplate to access the
Mounting Slots.
d. Remove the Left Sideplate to access the
Mounting Holes.
NOTICE: This motor weighs approximately 70 lbs.
We recommend having a second person help with
the installation.
Deployed Stowed
Left Sideplate
Right
Sideplate
Right
Sideplate
Screw Screw Left
Sideplate
Screw Screw
INSTALLING THE RIPTIDE ULTERRA
• #2 Phillips Screwdriver
• #3 Phillips Screwdriver
• Drill
• 9/32" Drill Bit
• A person to help
with installation
MOUNTING CONSIDERATIONS
TOOLS AND RESOURCES REQUIRED
INSTALLATION
View accessories
available for your
trolling motor at
minnkotamotors.com.
1
2
1b 1b
2c 2d

minnkotamotors.com | 7
©2019 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE RIPTIDE ULTERRA
e. Under the Left Sideplate, the Extension Damper
obstructs access to the left front Mounting Hole.
f. Using a small Screw Driver, remove the two
5/16" e-clips holding the Extension Damper in place.
Once the e-clips are removed, slide the Extension
Damper off the Damper Pins to expose the left rear
Mounting Hole. Set the two e-clips and Extension
Damper in a safe place so they are not misplaced
before they are reassembled later in the installation.
g. Make sure the Power Cables from the battery
are disconnected, or that the breaker, if equipped,
is “off”.
E-clips Extension
Damper
Extension
Damper
E-clip
E-clip
Mounting Hole
Power Cables
Deck of
Boat
Keel
Mount
h. Place the motor on the bow of the boat. Place the
motor as close to the centerline or keel of the boat
as possible. The motor can be installed on either the
Port or Starboard side of the boat based on personal
preference. Reviewing the mounting considerations
at the beginning of the installation section.
Damper Pins
NOTICE: The Emergency Strap (Item #16) is used
for Manually Stowing the Ulterra. The Emergency
Strap is not secured during installation. Store it on
your boat along with a #2 Philips screwdriver in the
event that you would need to manually stow the
motor. To learn how, please refer to the "Manually
Stowing the Ulterra" section of the Owner's Manual.
3
4
5
3e
3f
WARNING
Do not deploy the motor until it is fully mounted to the boat.
Illustrations are for reference only. Deploying your motor
before it is mounted to the boat may cause injury.
WARNING
Make sure the motor is mounted on a level surface and is
not connected to a power source.

8 | minnkotamotors.com ©2019 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE RIPTIDE ULTERRA
i. Make sure the slot on the underside of the Base
Extrusion is aligned with the outermost part of
the gunwale of the boat. This will ensure that the
Shaft has a minimum clearance of 1-1/2" when it is
deployed. The lower unit when stowed and deployed
must not encounter any obstructions.
j. Check to be sure that the Motor Mount is level. Use
the Rubber Washers (Item #7) provided to create a
level surface if necessary.
Bow
k. It is recommended to mark at least 4 of the 6 holes
in the Base Extrusion to have a minimum of two
bolts on each side that are located the farthest
apart. Ideal installation would allow for 6 bolts to
be used, with a minimum of 4.
l. Make sure the area under the mounting location is
clear to drill holes and install nuts and washers. Drill
through the marked holes using a 9/32" drill bit.
ITEM(S) NEEDED
Mounting Holes
Mounting Slots Base Extrusion
#7 x 6
Gunwale
Gunwale
Slot
Slot
Base
Extrusion
Shaft
Gunwale 1-1/2"
Minimum
6
WARNING
Do not deploy the motor until it is fully mounted to the boat.
Illustrations are for reference only. Deploying your motor
before it is mounted to the boat may cause injury.
7
CAUTION
Failure to allow 1-1/2" of clearance of the Shaft when mounting
may cause failures when the motor stows and deploys. Follow
recommended mounting considerations to avoid obstructions
when operating the motor.

minnkotamotors.com | 9
©2019 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE RIPTIDE ULTERRA
NOTICE: To prevent seizing of the stainless steel
hardware, do not use high speed installation tools.
Wetting the screws or applying an anti-seize may
help prevent seizing.
NOTICE: The Long Bolts, Flat Washers and Nylock
Nut are not used when installing the Riptide Ulterra
with a Quick Release Bracket.
Power Tilt Mounting Slots
Clipped
Washer Quick Release Bracket
Hex Head Bolt
#2 x 3 #5 x 3 #4 x 3 #6 x 3 #3 x 3
ITEM(S) NEEDED
m. Mount the motor to the boat using the provided
hardware. Place the installation hardware for the
side of the Motor where the Power Tilt is located
first. This is the opposite side of the Base Extrusion
from where the Extension Damper was removed.
The base of the Motor where the Power Tilt is
located has Mounting Slots and the side where the
Extension Damper is located has Mounting Holes.
n. If installing with a Quick Release Bracket, install
the motor with the Hex Head Bolts (Item #3)
and Clipped Washers (Item #4). Orientate the
Clipped Washers so that the flat side of the washer
is towards the Base Extrusion. The Bolt should
pass through the Clipped Washer and into a
Quick Release Bracket. Leave at least 1/4" space
between the Hex Head Bolt and Clipped Washer in
order to slide the Base Extrusion under the Clipped
Washer and into place.
Base Extrusion
8
9
CAUTION
Use extra care to avoid pinching and damaging the sensor wires
that run along side of the Base Extrusion when installing and
tightening the motor mounting bolts.
9n

10 | minnkotamotors.com ©2019 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE RIPTIDE ULTERRA
o. If installing directly to the boat deck, install the
motor with the Long Bolts (Item #2), Clipped Washer
(Item #4), Flat Washer (Item #5) and Nylock Nut
(Item #6). Orientate the Clipped Washers so that the
flat side of the washer is towards the Base Extrusion.
The Bolt should pass through the Clipped Washer,
the Rubber Washer and then through the Boat Deck.
The Bolt should be secured by first adding the Flat
Washer (Item #5) to the Bolt and securing with a
Nylock Nut (Item #6). Leave at least 1/4" space
between the Hex Head Bolt and Clipped Washer and
the deck of the boat. This will leave enough space
to slide the Base Extrusion between the Clipped
Washer and Rubber Washer and into place.
p. Slide the Base Extrusion into place under the Bolts
that were just installed.
q. If installing with a Quick Release Bracket, the Base
Extrusion should slide between the Quick Release
Bracket and the Clipped Washers. Hold the Clipped
Washers up on the Hex Head Bolt, so the Clipped
Washer will sit on top of the
Base Extrusion.
r. If installing directly to the boat deck, the Base
Extrusion should slide between the Clipped Washer
and the Rubber Washer. Hold the Clipped Washers
up on the Long Bolt, so the Clipped Washer will sit
on top of the Base Extrusion.
Base Extrusion
Power Tilt
Boat Deck
Clipped
Washer
Rubber Washer
Boat Deck
Long Bolts
Clipped
Washer
Rubber
Washer
Flat Washer
Nylock Nut
Power
Tilt
NOTICE: The Short Bolts are not used when
installing the Riptide Ulterra directly to the boat.
Power Tilt
Base
Extrusion
Quick Release Bracket
Clipped Washer
10 10o
11 11q
11r

minnkotamotors.com | 11
©2019 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE RIPTIDE ULTERRA
s. Place the hardware on the Damper side of the
mount into the Mounting Holes to secure the
Base Extrusion.
t. If installing with a Quick Release Bracket, install
the motor with the Hex Head Bolts (Item #3) and
Clipped Washers (Item #4). Orientate the Clipped
Washers so that the flat side of the washer is
towards the Base Extrusion. The Bolt should pass
through the Clipped Washer, Base Extrusion and
into a Quick Release Bracket.
ITEM(S) NEEDED
Mounting Holes
Mounting Holes
Boat Deck
Long Bolts
Clipped
Washer
Rubber
Washer
Flat Washer
Nylock Nut
#2 x 3#5 x 3 #4 x 3 #6 x 3 #3 x 3
NOTICE: To prevent seizing of the stainless steel
hardware, do not use high speed installation tools.
Wetting the screws or applying an anti-seize may
help prevent seizing.
NOTICE: The Long Bolts, Flat Washers and Nylock
Nut are not used when installing the Riptide Ulterra
with a Quick Release Bracket.
NOTICE: The Short Bolts are not used when
installing the Riptide Ulterra directly to the boat.
Mounting
Holes
Quick Release Bracket
Hex Head Bolt
Clipped
Washer
12
CAUTION
Use extra care to avoid pinching and damaging the sensor wires
that run along side of the Base Extrusion when installing and
tightening the motor mounting bolts.
12s
12t
12u
u. If installing directly to the boat deck, install the
motor with the Long Bolts (Item #2), Clipped
Washer (Item #4), Flat Washer (Item #5) and
Nylock Nut (Item #6). Orientate the Clipped
Washers so that the flat side of the washer is
towards the Base Extrusion. The Bolt should pass
through the Clipped Washer, the Base Extrusion, the
Rubber Washer and then through the Boat Deck.
The Bolt should be secured by first adding the Flat
Washer (Item #5) and then securing with a Nylock
Nut (Item #6).

12 | minnkotamotors.com ©2019 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE RIPTIDE ULTERRA
v. At this point in the installation process the Motor
should be secured to the deck of the boat, and
the Motor can now be reassembled. The Extension
Damper can be slid back in place on the Damper
Pins. This should be done so the shaft on the Damper
is pointing inboard. Reinstall the two 5/16" E-clips.
w. Replace the Right Sideplate.
x. Replace the Left Sideplate.
y. Replace the four sideplate Screws using a #2 or #3
Phillips Screw Driver.
Left Sideplate
Screw
Screw
Screw
Right Sideplate
Screw
E-clips Extension Damper Damper Pins
13
14 14w
14x

minnkotamotors.com | 13
©2019 Johnson Outdoors Marine Electronics, Inc.
ROUTING -PILOT LINK CABLES
Your trolling motor will be pre-installed with either i-Pilot or i-Pilot Link. To learn more about the GPS capabilities available with your
i-Pilot or i-Pilot Link navigation system, please refer to the corresponding Owner's Manual by visiting minnkotamotors.com.
The i-Pilot Link features require a cable to be connected to an
output device. This connection is present on the trolling motor
below the Control Head, if installed. The i-Pilot system does not
need an external wired connection. If a connecting cable is
present, your motor is equipped with the i-Pilot Link system. If no
connections are present, your motor may or may not be installed with i-Pilot. Please follow the Minn Kota recommendations on routing the
cables to optimize mobility and maximize functionality.
The Ethernet cable for the i-Pilot Link system has an 8 pin connector. The i-Pilot Link system can be connected directly to the
Humminbird or to the Humminbird Ethernet Switch (optional). If you purchase an Ethernet Switch, install it using the instructions
included in the Ethernet Installation Guide. The Ethernet Extension Cable is optional for your installation. To purchase Ethernet switches,
Ethernet cables, and extension cables, visit the web site humminbird.com or call Humminbird Customer Service at 1-800-633-1468.
Depending on the shape of the Ethernet port on your Humminbird fish finder, an additional ethernet adapter cable (Ethernet Adapter
Cable AS EC QDE #720074-1 for Helix fish finders) may be required for the installation. Refer to your fish finder operations manual or see
the i-Pilot Link Compatibility Chart on our web site with a list of all compatible Humminbird Units and SC Cards.
Use the following instructions to properly route and connect cables. Cables are shielded to minimize interference. To protect this shielding
the cables should not be pulled tight against sharp angles or hard objects. If using cable ties, do not over-tighten. Any excess cable
should be bundled in a loose loop of no less than 4" in diameter.
To minimize trolling motor interference, ensure that the fish finder and trolling motor are powered by separate batteries. Please refer
to the Battery & Wiring Installation and Motor Wiring Diagram sections of this manual for correct rigging instructions.
Routing and Connecting i-Pilot Link Cables
NOTICE: The i-Pilot Link system needs an external wired
connection. The i-Pilot system does not need an external
wired connection.
a. Begin with the motor in the deployed position.
b. Locate the i-Pilot Link cable, at the base of the
Control Head.
CAUTION
Not following the recommended wire routing for the i-Pilot
Link cable, if equipped, may cause damage to the product
and void your product warranty. Route cables away from
pinch points or other areas that may cause them to bend
in sharp angles. Routing the cables in any way other than
directed may cause damage to the cables by being pinched
or severed.
1i-Pilot
Link
Control Head
Coil Cord
i

14 | minnkotamotors.com ©2019 Johnson Outdoors Marine Electronics, Inc.
ROUTING -PILOT LINK CABLES
c. The i-Pilot Link cable should be fed all the way
through the Coil Cord. They should exit the Coil
Cord at the bottom of the Coil Cord, where it
connects to the Motor Mount.
Control Head
Coil Cord
Mount
i-Pilot
Link
2
NOTICE: After the i-Pilot Link Cable exits the Coil
Cord, it should be routed through an established
routing system on the boat, in an area with minimal
interference. Inspect the selected route carefully to
ensure that there are no sharp edges, obstacles, or
obstructions that may damage the cables.
d. If necessary, to reach the installed fish finder, take the
i-Pilot Link Ethernet Cable (Item #14) and attach it to
the i-Pilot Link cable exiting the Control Head.
e. Install the i-Pilot Link Ethernet Cable directly into
the Humminbird fish finder, or refer to your fish
finder installation manual for complete installation
instructions. If an Adapter Cable is needed (Ethernet
Adapter Cable AS EC QDE for Helix fish finders),
install it on the end of the i-Pilot Link Ethernet
Cable and refer to your fish finder installation
manual for complete installation instructions.
3
i-Pilot Link Ethernet
Cable from Control Head
i-Pilot Link Ethernet
Extension Cable OR
Ethernet Adapter Cable
Locking
Collar
Eight Pin
Connector
#14 x 1
ITEM(S) NEEDED
NOTICE: If any cables need to be routed, please
follow the guidelines in the Routing Connection
Cables section of these installation instructions.
NOTICE: The connectors are keyed to prevent
reversed installation.
i

minnkotamotors.com | 15
©2019 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE PROP
Installing the Prop
1
a. Take the Drive Pin (Item #18) and slide it through
the Hole in the Armature Shaft. Position the Drive
Pin horizontal by grasping the Armature Shaft and
rotating it with the Drive Pin in place.
b. Align the Propeller (Item #17) so it is also horizontal
and parallel with the Drive Pin. Slide the Propeller
onto the Armature Shaft and Drive Pin until it is
seated against the lower unit.
c. Install the Prop Washer (Item #19) and the Prop
Nut (Item #20) onto the end of the Armature Shaft.
d. Holding the end of the Armature Shaft with a Flat
Blade Screwdriver, tighten the Prop Nut with a 9/16"
Open End Wrench.
e. Tighten the Prop Nut 1/4 turn past snug to
25-35 in-lbs.
Propeller
Propeller
Prop Nut
Prop Washer
Drive Pin
Propeller
Prop Nut
Prop Washer
Drive Pin
Armature
Shaft
CAUTION
Disconnect the motor from the battery before beginning any
prop work.
CAUTION
Do not over tighten as this can damage the prop.
ITEM(S) NEEDED
#18 x 1#20 x 1
#19 x 1
#17 x 1
1a
1b
1d
NOTICE: Discard the shipping spacer, lock nut and
shipping washer. These items corrode quickly and can
ruin parts.

16 | minnkotamotors.com ©2019 Johnson Outdoors Marine Electronics, Inc.
DEPLOYING THE MOTOR WITH I-PILOT
Deploying the Motor with i-Pilot
a. Press the Home button.
b. Use the Menu Up and Menu Down buttons to
find the Deploy menu at the bottom of the display
screen.
NOTICE: The Deploy menu at the bottom of the
display screen can only be found when the motor
is stowed.
c. Use the Right Softkey to select the Deploy menu
by double pressing it. Once selected the motor will
automatically deploy.
d. While the Motor is deploying, it is possible to stop
the action. Use either the Left Softkey to select
the Stow menu or the Right Softkey to select the
Pause menu.
e. If the Motor continues, it will complete the deploy
process, normal motor operation will follow.
WARNING
As soon as the Deploy menu is selected, the motor will
automatically deploy. Be sure the motor is clear from
obstructions and has a clear path of travel. The Prop is
disabled while the motor is stowed and being deployed to
prevent accidental contact with the rotating propeller.
Stowing the Motor with i-Pilot
a. Press the Home button.
b. Use the Menu Up and Menu Down buttons
to find the Stow menu at the bottom of the display
screen.
NOTICE: The Stow menu at the bottom of the
display screen can only be found when the motor
is deployed.
1
2
1
1a 1b
2d 2e
1a 1b
i
QUICK STOW & DEPLOY

minnkotamotors.com | 17
©2019 Johnson Outdoors Marine Electronics, Inc.
DEPLOYING THE MOTOR WITH I-PILOT LINK
c. Use the Right Softkey to select the Stow menu.
Once selected the motor will automatically stow.
d. While the Motor is stowing, it is possible to stop the
action. Use either the Left Softkey to select the
Deploy menu or the Right Softkey to select the
Pause menu.
e. If the Motor continues, it will complete the Stow
process and the Prop will be disabled.
WARNING
As soon as the Stow menu is selected, the motor will
automatically stow. Be sure the motor is clear from
obstructions and has a clear path of travel. The Prop
is disabled while the motor is being stowed to prevent
accidental contact with the rotating propeller.
Deploying the Motor with i-Pilot Link
a. Press the Home button.
b. Scroll through the Content Area using either your
finger or the Screen Navigation button to find the
Ulterra button.
c. Select the Ulterra button using either your
finger or by pressing the Ok button to open the
Ulterra Menu.
NOTICE: The Ulterra button can only be found in
the Content Area with the Home Control Buttons
on i-Pilot Link systems on an Ulterra motor. Certain
Home Screen Buttons may be locked out while the
motor is stowed because those functions require the
motor to be deployed to operate.
22d 2e
11c 1c
i

18 | minnkotamotors.com ©2019 Johnson Outdoors Marine Electronics, Inc.
DEPLOYING THE MOTOR WITH I-PILOT LINK
d. Once in the Ulterra Menu, find the Deploy
button and select it. The Deploy button requires
a double press to engage.
e. The Ulterra motor will deploy. While the Motor is
deploying, it is possible to pause the action. To
pause the action, find the Pause button and
select it.
f. To resume the Deploy action, select the Deploy
button.
g. If the Motor continues, it will complete the deploy
process and normal motor operation will follow.
WARNING
As soon as the Deploy button is selected, the motor will
automatically deploy. Be sure the motor is clear from
obstructions and has a clear path of travel. The Prop is
disabled while the motor is stowed and being deployed to
prevent accidental contact with the rotating propeller.
22d 2e
2f 2g
i

minnkotamotors.com | 19
©2019 Johnson Outdoors Marine Electronics, Inc.
STOWING THE MOTOR WITH I-PILOT LINK
Stowing the Motor with i-Pilot Link
d. Once in the Ulterra Menu, find the Stow button
and select it.
NOTICE: The Stow button can only be found
when the motor is deployed.
e. The Ulterra motor will stow. While the Motor is
stowing, it is possible to pause the action. To pause
the action, find the Pause button and select it.
WARNING
As soon as the Stow button is selected, the motor
will automatically stow. Be sure the motor is clear from
obstructions and has a clear path of travel. The Prop
is disabled while the motor is being stowed to prevent
accidental contact with the rotating propeller.
a. Press the Home button.
b. Scroll through the Content Area using either your
finger or the Screen Navigation button to find the
Ulterra button.
c. Select the Ulterra button using either your
finger or by pressing the Ok button to open the
Ulterra Menu.
NOTICE: The Ulterra button can only be found
in the Content Area with the Home Control Buttons
on i-Pilot Link systems on an Ulterra motor. The motor
can only be stowed when it is currently deployed.
2
11c 1c
2d 2e
i

20 | minnkotamotors.com ©2019 Johnson Outdoors Marine Electronics, Inc.
BATTERY WIRING & INSTALLATION
BOAT RIGGING & PRODUCT INSTALLATION
For safety and compliance reasons, we recommend that you follow American Boat and Yacht Council (ABYC) standards when rigging
your boat. Altering boat wiring should be completed by a qualified marine technician. The following specifications are for general
guidelines only:
CONDUCTOR GAUGE AND CIRCUIT BREAKER SIZING TABLE
This conductor and circuit breaker sizing table is only valid for the following assumptions:
1. No more than 2 conductors are bundled together inside of a sheath or conduit outside of engine spaces.
2. Each conductor has 105° C temp rated insulation.
3. No more than 5% voltage drop allowed at full motor power based on published product power requirements.
NOTICE: Wire Extension Length refers to the distance from the batteries to the trolling motor leads. Consult website for
available thrust options. Maximum Amp Draw values only occur intermittently during select conditions and should not be used as
continuous amp load ratings.
Reference
United States Code of Federal Regulations: 33 CFR 183 – Boats and Associated Equipment ABYC E-11: AC and DC Electrical Systems on Boats
Motor Thrust / Model Max
Amp Draw Circuit Breaker Wire Extension Length
5 feet 10 feet 15 feet 20 feet 25 feet
30 lb. 30 50 Amp @ 12 VDC 10 AWG 10 AWG 8 AWG 6 AWG 4 AWG
40 lb., 45 lb. 42 10 AWG 8 AWG 6 AWG 4 AWG 4 AWG
50 lb., 55 lb. 50 60 Amp @ 12 VDC 8 AWG 6 AWG 4 AWG 4 AWG 2 AWG
70 lb. 42 50 Amp @ 24 VDC 10 AWG 10 AWG 8 AWG 8 AWG 6 AWG
80 lb. 56 60 Amp @ 24 VDC 8 AWG 8 AWG 8 AWG 6 AWG 6 AWG
101 lb. 46 50 Amp @ 36 VDC 8 AWG 8 AWG 8 AWG 8 AWG 8 AWG
Engine Mount 101 50 60 Amp @ 36 VDC 8 AWG 8 AWG 8 AWG 8 AWG 8 AWG
112 lb. 52 60 Amp @ 36 VDC 8 AWG 8 AWG 8 AWG 8 AWG 8 AWG
Engine Mount 160 116 (2) x 60 Amp @ 24 VDC 6 AWG 6 AWG 4 AWG 2 AWG 2 AWG
E-Drive 40 50 Amp @ 48 VDC 10 AWG 10 AWG 10 AWG 10 AWG 10 AWG
CAUTION
These guidelines apply to general rigging to support your Minn Kota motor. Powering multiple motors or additional electrical devices
from the same power circuit may impact the recommended conductor gauge and circuit breaker size. If you are using wire longer than
that provided with your unit, follow the conductor gauge and circuit breaker sizing table below. If your wire extension length is more
than 25 feet, we recommend that you contact a qualified marine technician.
CAUTION
An over-current protection device (circuit breaker or fuse) must be used. Coast Guard requirements dictate that each ungrounded
current-carrying conductor must be protected by a manually reset, trip-free circuit breaker or fuse. The type (voltage and current rating)
of the fuse or circuit breaker must be sized accordingly to the trolling motor used. The table below gives recommended guidelines for
circuit breaker sizing.