Mirage SERIES A User manual

WARNING: If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss of life.
-- Do not store or use gasoline or other flammable vapours and liquids in the
vicinity of this or any other appliance.
-- WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electrical switch; do not use any phone in your building.
- Immediately call your gas supplier from a neighbour’s phone. Follow the
gas supplier’s instructions.
- If you cannot reach your gas supplier, call the fire department.
--Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
SERIES A
INSTALLATION AND
OPERATING
INSTRUCTIONS
IMPORTANT: THESE INSTRUCTIONS
ARE TO REMAIN WITH THE
HOMEOWNER
DIRECT VENT
ROOM HEATER
fire-parts.com

2
Contents
CAUTION ....................................................................................... 3
SAFETY.......................................................................................... 3
MAINTENANCE ............................................................................. 3
LIGHTING INSTRUCTIONS ........................................................... 4
OPERATING .................................................................................. 5
GAS FLAME ADJUSTMENT ......................................................... 5
GAS SUPPLY ................................................................................. 6
ELECTRICAL ................................................................................. 6
BLOWER OPERATION.................................................................. 6
CLEARANCES ............................................................................... 6
INSTALLATION PRECAUTIONS .................................................. 7
STRAIGHT THROUGH WALL ....................................................... 8
CORNER INSTALLATION ............................................................. 9
BASEMENT INSTALLATION ...................................................... 11
FLOOR PROTECTION................................................................. 11
VENT TERMINAL INSTALLATION ............................................. 12
LOG SET ...................................................................................... 13
REPLACEMENT PARTS ............................................................. 15
fire-parts.com

3
CAUTION
FOR YOUR SAFETY - Do not install or operate your Pacific Energy
Mirage without first reading and understanding this manual. Any
installation or operational deviation from the following instructions voids
the Pacific Energy Gas Stove Warranty and may prove hazardous.
This appliance and its individual shutoff valve must be disconnected
from gas supply piping system during any pressure testing of that
system at test pressures in excess of 1/2 psig. (3.5 kPa)
This appliance must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure testing
of the gas supply piping system at test pressures equal to or less than
1/2 psig. (3.5 kPa)
Note: When lit for the first time, the appliance will emit a slight odour
for a couple of hours. This is due to the curing of paints, sealants and
lubricants in the manufacturing process. This condition is temporary.
Open doors and windows to ventilate area. Smoke and fumes caused
by the curing process may cause discomfort to some individuals.
SAFETY
Due to high temperatures, this gas appliance should be lo-
cated out of traffic and away from furniture and draperies.
Children and adults should be alerted to the hazards of high
surface temperature and should stay away to avoid burns or
clothing ignition.
Young children should be carefully supervised when they are
in the same room as the appliance.
Clothing or other flammable material should not be placed on
or near the appliance.
Any grill, panel or door removed for servicing the unit must be
replaced prior to operating. Failure to do so may create a hazard-
ous condition.
Installation and repair should be done by a qualified service
person. The appliance should be inspected before use and at least
annually by a professional service person. More frequent cleaning
may be required due to excessive lint from carpeting, bedding
material, etc. It is imperative that control compartments, burners
and circulating air passageways of the appliance be kept clean.
It is Pacific Energy’s policy that no responsibility is assumed by
the Company or by any of its employees or representatives for any
damages caused by an inoperable, inadequate, or unsafe condi-
tion which is the result, either directly or indirectly, of any im-
proper operation or installation procedures.
MAINTENANCE
Caution: Turn off gas and electrical power supply and allow ample time
for unit to cool before servicing appliance. It is recommended that this
appliance and venting should be inspected at least once a year by a
qualified service person.
Do not use this heater if any part has been under water. Immediately call
a qualified service technician to inspect the heater and to replace any
part of the control system and any gas control which has been under
water.
Annual Inspection:
a) Clean louvres and air passage ways of excessive lint build-up from
carpeting, bedding material, etc. The flow of ventilation air must not be
obstructed.
b) Remove glass panel and log set. Inspect logs and burner assembly
for lint and soot build-up. If excessive build-up of soot is present, have
a qualified serviceman inspect and adjust unit for proper combustion.
Clean logs and burner with a vacuum cleaner, paying close attention to
the ports on the burner.
c) Check the pilot system for proper flame size and operation. Clean
pilot free of lint and dust (See Fig. #1).
d) Check that the vent pipe and vent terminal are open and free from
blockage or debris.
e) Check glass panel gasket, replace if necessary.
Note: The appliance area must be kept clear and free from combustible
materials, gasoline and other flammable vapours and liquids.
Periodically:
a) Viewing glass may be cleaned with glass cleaner.
b) Exterior porcelain enamel finish may be cleaned with soap and water.
Note: Never use abrasive to clean this appliance.
Fig. # 1
fire-parts.com

4
FOR YOUR SAFETY READ BEFORE LIGHTING
If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
WARNING:
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this page.
2. Set wall thermostat to lowest setting. (if applicable)
3. Turn off all electric power to the appliance.
4. Turn burner control dial clockwise to “Off” position.
5. Partially depress and turn gas control dial clockwise
past “Pilot” to “Off” position.
Note: Knob cannot be turned from “Pilot” to “off” unless knob
is pushed in slightly. Do not force.
6. Allow sufficient length of time (minimum 5 minutes) for any
gas in the combustion chamber to escape. If you still smell
gas, STOP! Follow “B” in the safety information on above
on this page. If you don’t smell gas, go to the next step.
7. Turn gas control knob back to “Pilot” position.
8. Depress gas control knob fully and hold while you ignite
pilot with the rotary igniter. Once the pilot ignites, continue
depressing knob for approximately 1/2 minute. If pilot does
TO TURN OFF GAS TO APPLIANCE
1. Set wall thermostat to lowest setting. (if applicable)
2. Turn off all electric power to the appliance if service is to be
performed.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
- Do not try to light any appliance.
- Do not touch any electric switch; do not use any phone in
your building.
- Immediately call your gas supplier from a neighbour’s
phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or turn
by hand, don’t try to repair it, call a qualified service
technician. Force or attempted repair may result in a fire or
explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
MAIN VALVE
Gas control knob
shown in OFF position
PILOT
BURNER
THERMOPILE
not stay lit, repeat steps 4 through 7, allowing a longer
period before releasing gas control knob.
- If gas control knob does not pop up when released, stop
and immediately call your service technician or gas
supplier.
- If the pilot will not stay lit after several tries, turn the gas
control dial to “off” and call your service technician or gas
supplier.
9. To normally light the pilot, use the rotary igniter.
10. To light pilot by hand, remove front glass panel. Locate
pilot just behind the front log and to the right. Repeat steps
5 through 8, lighting the pilot
with a match instead of rotary
igniter.
11. Replace front glass panel.
12. Turn gas control knob counter-clockwise to “On”
position.
13. Turn on all electric power to the appliance.
14. Set wall thermostat to desired setting. (if applicable)
Note: Sufficient time must be allowed for air to escape from
lines if the unit is being lit for the first time.
3. Push in gas control knob slightly and turn clockwise
to “Off”. Do not force.
fire-parts.com

5
OPERATING
Once a pilot light has been established, the unit may be operated one
of two ways:
Manual:
1) Turn burner control dial to desired setting. (Set to Hi, Med, or Low
only - do not operate in between settings. See Fig. # 2) To turn unit
off, turn burner control dial to “OFF” position.
Remote:
Optional wall switch or wall thermostat is required. (Fig. # 3)
1) Turn burner control dial to desired setting. (Set to Hi, Med, or Low
only - do not operate in between settings. See Fig. # 2.) The unit may
be turned on or off via wall switch, or automatically by the wall
thermostat.
Extend Shutdown:
1) Partially depress and turn gas control dial clockwise past “PILOT”
to “OFF” position.
To re-light unit, see “lighting instructions” section.
Note: When lit for the first time, the appliance will emit a slight odour for
a couple of hours. This is due to the curing of paints, sealants and
lubricants in the manufacturing process. This condition is temporary.
Open doors and windows to ventilate area.
GAS FLAME ADJUSTMENT
The air shutter on the burner venturi tube controls the primary combus-
tion air to the gas burner. Although it is preset at the factory, some
adjustment may be necessary to obtain desired flame and to eliminate
carbon deposits. (See Fig. # 4 for proper flame pattern)
To Adjust: (See Fig. # 5)
1) Loosen retaining screws and open left side panel to expose controls
2) Move air shutter adjustment rod in or out until proper flame is
achieved.
3) Close control side panel.
Caution: Proper air shutter setting is a must. The flame should be just
orange and “lazy”. It should NEVER be set to create sooting on internal
parts and glass. Open air shutter gradually until sooting stops.
BURNER
CONTROL
LOW
MED
HIGH
OFF
Fig. # 2
Burner Control Dial
shown in OFF position
Fig. # 3
Fig. # 4
Fig. # 5
fire-parts.com

6
GAS SUPPLY
The Mirage Gas Appliance comes equipped with a flexible 3/8" N.P.T.
Male inlet for easy gas connection. This connector is located behind the
left side panel.
Correct gas pressure requirement:
Natural Gas
Min. Pressure 5.0" wc
(For purpose of input adjustment)
Max Pressure 10.5" wc
Manifold Pressure 3.5" wc
Proper gas line diameter must be used to assure proper operation. A
pressure test port (1/8 inch N.P.T. plugged tapping) must be provided
for checking gas pressure. This port must be located immediately
upstream of the gas supply connection to the appliance.
ELECTRICAL
No electrical connection is required for the gas system operation. The
self generating pilot provides current for the optional remote wall switch
or wall thermostat. (See fig. # 4 for proper installation.)
Circulating air blower electrical rating: 115V, 60HZ, 80 watts. (See Fig.
# 7 for blower wiring diagram) For your protection against shock hazard,
use only a properly grounded outlet that will accept a three-pronged
plug. Do not cut or remove the grounding prong.
Consult local codes or, in the absence of local codes, with the current
CSA C22.1 Canadian Electrical Code and in the USA with the National
Electrical Code, ANSI/NFPA 70 (Latest Edition)
BLOWER OPERATION
The circulating air blower is thermostatically controlled and will not
operate if appliance is cold. A few minutes after the appliance is lit and
the variable speed control set at a desired setting, the blower will
automatically turn on. The blower will automatically turn off a few
minutes after the appliance is shut down.
CLEARANCES
The minimum clearances from the appliance to combustibles are shown
on Fig. # 8. For purpose of servicing, a 12" right side (side with controls)
clearance is recommended. Adequate clearances around air openings
and combustion air supply are required.
Fig # 7
G (green)
L2 (black)
L1 (white)
115 VOLTS
60 Hz
0.5 AMPERES
If any of the original
wire must be replaced,
it must be replaced with
type GTF wire or its
equivalent.
SPEED
CONTROL
Minimum Clearance
to Combustibles
Fig. # 8
Sidewall to Appliance 3 in (76 mm)
Rearwall to Appliance 1 in. (25 mm)
Corner to Appliance 1 in. (25 mm)
BLOWER (part #21 A)
SNAP DISC
SWITCH (part #24)
fire-parts.com

7
INSTALLATION PRECAUTIONS
The Mirage Gas Appliance installation and venting must conform
to the current CAN/CGA-B149 installation code (in Canada) or the
current National Fuel Gas Code, ANSI Z223.1 (in the USA), and
approved per local codes. Only qualified (licensed or trained)
personnel should install this product.
For Mobile Housing installation, the installation must conform to
the current CSA Z240.4 installation code (in Canada) or the Stand-
ard for Manufactured Home Installations, A225.1/NFPA 501A. (in
the U.S.A.), and approved per local codes. Only qualified (licensed
or trained) personnel should install this product.
VENT SYSTEM
Before starting installation of vent kits , the installer should read these
instructions to insure that the proper vent system has been selected for
the installation.
Vent systems approved for use with the Mirage Direct Vent are shown
in Figure 8. Approved vent systems components are labelled for
identification. NO OTHER VENTING SYSTEMS OR COMPONENTS
MAY BE USED.
Connections between each vent system component must be tightly
joined and sealed, and secured with sheetmetal screws at each joint.
Consult your local Building Codes before beginning the installation.
CAUTION: UNDER NO CONDITION SHOULD COMBUSTIBLE
MATERIAL BE CLOSER THAN 1-INCH FROM THE VERTICAL AND
HORIZONTAL SECTIONS OF THIS VENT SYSTEM.
Fig # 8
PART # PART DESCRIPTION
fire-parts.com

8
Fig. # 9
STRAIGHT THROUGH WALL
1) Determine the exact position of the gas stove so that the direct vent
pipe is centered (if possible) between two building framing members.
This will avoid any extra framing.
2) Carefully measure up 23-inches from the finished floor and mark the
center of a 9-inch square or round hole. (See Figure #10)
IMPORTANT: When locating this hole it should be noted that the
bottom of the vent terminal must be a MINIMUM of 12-inches above
grade, the top of the terminal must be a MINIMUM of 24-inches below
combustible material such as a deck or roof overhang and the side
of the terminal must be a MINIMUM of 12-inches away from an
adjacent wall. (See Figure 15)
3) Cut a 9-inch square or round hole through the exterior wall of the
building.
4) Position the wall thimble spacer (WTS) from the inside through the 9-
inch hole . (Figure 10). For walls less than 11-inches thick, the thimble
must be trimmed back flush with the exterior wall.
5) Attach the trim collar to the flanges of the wall thimble with the screws
provided.
6) The coaxial starter pipe (SK 12) may have to be cut to length
depending on the wall thickness and/or rear clearance of the stove.
Measure the wall thickness from the finished trim collar surface to the
exterior mounting surface for the vent terminal. Add 1/4-inches plus
rear clearance to the wall thickness (i.e. rear clearance of 1", add 1
1/4" , rear clearance of 3", add 3 1/4" to wall thickness).
7) Cut both pipes to this length. Do not cut off the crimp-bead off the 5-
inch inner pipe.
8) The vent pipe must be attached to the collars of the gas stove with the
bead end towards the appliance. Slide the inner 5-inch flue pipe over
top of the collar up to the crimp-bead and attach with three sheetmetal
screws. Seal the joint with high temperature silicone. Next, slide the
7-inch outer pipe over the 5-inch pipe fully and secure to the pipe collar
with three sheetmetal screws. Assure that the vent pipe is level.
9) Slide the appliance into place, with vent pipe centered in wall pass-
through. When the unit is properly installed, the 7-inch vent pipe will
project 3/4-inch past the outside wall surface and the 5-inch inner pipe
will extend 1-inch past that. The coaxial vent pipe must be level.
10) Install vent terminal according to section VENT TERMINAL INSTAL-
LATION
Fig. # 10
fire-parts.com

9
CORNER INSTALLATION
1) Determine the exact position of the gas stove, making sure the unit will
be set at 45° to the walls and the corner clearance will not be less then
1-inch. The vent pipe should be centered (if possible) between two
building members. This will avoid any extra framing.
2) Once the desired location is found, carefully measure up 23-inches
from the finished floor and make a mark. Next, measure 7-inches plus
the actual corner clearance of the appliance over from the corner of
the room and make a mark. (i.e. corner clearance of 1", measure 8";
corner clearance of 3", measure 10")
IMPORTANT: When locating this hole it should be noted that the
bottom of the vent terminal must be a MINIMUM of 12-inches above
grade, the top of the terminal must be a MINIMUM of 24-inches below
combustible material such as a deck or roof overhang and the side
of the terminal must be a MINIMUM of 12-inches away from an
adjacent wall. (See Figure 15)
3) Cut a 9-inch square or round hole through the exterior wall of the
building.
4) Position the wall thimble spacer (WTS) from the inside through the 9-
inch hole . (Figure 10). For walls less than 11-inches thick, the thimble
must be trimmed back flush with the exterior wall.
5) Attach the trim collar to the flanges of the wall thimble with the screws
provided.
6) Attach the coaxial 45° elbow (LB 45) to the unit. Slide the 5-inch inner
elbow pipe 1-inch over top of the collar and secure with three
sheetmetal screws. Seal the joint with high temperature silicone.
Next, slide the outer elbow pipe over the smaller elbow and secure to
the pipe collar with three sheetmetal screws.
7) The coaxial starter pipe (SK 12) may have to be cut to length
depending on the wall thickness and/or corner clearance of the stove.
Measure the wall thickness from the finished trim collar surface to the
exterior mounting surface for the vent terminal. Add 3 3/4-inches plus
corner clearance to the wall thickness. (i.e. corner clearance of 1",
add 4 3/4" , corner clearance of 3", add 6 3/4" to wall thickness)
8) Cut both pipes to this length.
9) Slide the inner 5-inch flue pipe over top of the crimped end of elbow
and attach with three sheetmetal screws. Seal the joint with high
temperature silicone. Next, slide the 7-inch outer elbow pipe over the
5-inch elbow fully and secure to the elbow with three sheetmetal
screws. Assure that the vent pipe is level.
10) Slide the appliance into place making sure vent pipe is centered in wall
pass-through. When the unit is properly installed, the 7-inch vent pipe
will project 3/4-inch past the outside wall surface and the 5-inch inner
pipe will extend 1-inch past that.
11) Install vent terminal according to section VENT TERMINAL INSTAL-
LATION
Fig. # 11
fire-parts.com

10
Fig. # 12
fire-parts.com

11
BASEMENT INSTALLATION
1) In planning a basement installation it is necessary to determine the
exact position of the gas stove, the location of the vent terminal and
the length of vent pipe to be used. Various combinations of vertical
and horizontal vent pipe may be employed. Always plan your instal-
lation to minimize extra framing. The breeching through the exterior
wall should be centered (if possible) between two building members.
IMPORTANT: When locating this hole it should be noted that the
bottom of the vent terminal must be a MINIMUM of 12-inches above
grade, the top of the terminal must be a MINIMUM of 24-inches below
combustible material such as a deck or roof overhang and the side
of the terminal must be a MINIMUM of 12-inches away from an
adjacent wall. (See Figure 15)
2) Attach the coaxial vent pipe or 90° elbow with crimped end away from
unit. All joints and seams in the vent system should be sealed with high
temperature silicone.
3) Continue adding vent components per the pre-planned system con-
figuration. Support spacer must be used for each 6-feet of vertical and
horizontal run. The spacers are placed around the pipe and nailed or
screwed to the framing members. Maintain a minimum 1-inch clear-
ance to combustibles.
4) The starter pipe (SK 12 or SK 24) must be the last section in the vent
system. The pipe may have to be cut to length depending on the wall
thickness and/or position of vent system. Cut both pipes to the same
length. Do not cut off the crimp-bead off the 5-inch inner pipe.
5) When the unit and venting is properly installed, the 7-inch vent pipe
will project 3/4-inch past the outside wall surface and the 5-inch inner
pipe will extend 1-inch past that.
6) Install vent terminal according to section VENT TERMINAL INSTAL-
LATION
WARNING: MAKE CERTAIN THAT THE ELBOW ASSEMBLY OR
STRAIGHT PIPE SECTION IS PUSHED ALL THE WAY ONTO THE
STARTING COLLARS AND IS SECURELY FASTENED.
FLOOR PROTECTION
The Mirage direct vent appliance may be installed on a combustible floor.
If the appliance is to be installed on flooring that may make the unit
unstable, the appliance must be fastened to the structure or installed on
a metal or wood panel extending the full depth and width of the unit.
Fig. # 13
HORIZONTAL AND VERTICAL
VENT COMBINATION
(TWO 90° ELBOWS MUST BE USED)
fire-parts.com

12
Fig # 15
Fig. # 14
VENT TERMINAL INSTALLATION
1) Install the vent terminal on the outside wall. When placing the vent
terminal, make sure the collars on the terminal inserts into the
corresponding vent pipe.
2) Attach terminal to the wall with screws at each corner. (see Fig. #14)
NOTE: THE VENT TERMINAL MUST BE POSITIONED SO THAT
THE FLUE OUTLET IS POINTING UP.
3) Caulk in place to prevent any moisture entering the structure.
MINIMUM CLEARANCES TO THE VENT TERMINAL MUST BE
MAINTAINED. (SEE FIG. # 15)
NOTE: LOCAL CODES OR REGULATIONS MAY REQUIRE DIF-
FERENT CLEARANCES.
VENT TERMINAL MINIMUM
CLEARANCES
fire-parts.com

13
LOG SET
The log set comes installed in the appliance from the factory. If the logs
have to be removed for cleaning, they must be handled carefully as they
are very fragile. To re-install the log set, follow this procedure:
1) Place the back log on the rear tabs of the burner assembly, with flat
side facing rear and bark side forward.
2) Place the front log on the tabs located at the front of the burner. The
log is notched to fit over top of the pilot.
3) The top "Y" log bridges across from the front log to the rear log. The
log should be properly seated in the relief of the front and rear log.
Top Log
Front Log
Back Log
Fig. # 16
Note: Improper placement of logs may cause soot-
ing on internal parts and glass.
Step 1
Back Log Placement
Step 2
Front Log Placement
Step 3
Top Log Placement
fire-parts.com

14
DV MAIN BODY .............................................................. 1 A
TOP PANEL .................................................................... 2
LEFT SIDE PANEL ......................................................... 3
DV CONTROL SIDE PANEL .......................................... 4 A
DV CONTROL DOOR .................................................... 5 A
PEDESTAL COVER ....................................................... 6
'MIRAGE' LOGO (not shown) ........................................ 7
TOP LOUVER ................................................................. 8
BOTTOM LOUVER ......................................................... 9
DV FRONT TRIM ............................................................ 10 A
DV GLASS FRAME ........................................................ 11
GLASS PANEL ............................................................... 12
DV GLASS GASKET KIT (not shown) ........................... 14 A
DV LOG SET COMPLETE (#17 A, 19 A, & 20 A) .......... 16 A
DV FRONT LOG (see fig. #16) ...................................... 17 A
DV BACK LOG (see fig. #16) ......................................... 19 A
DV TOP LOG (see fig. #16) ........................................... 20 A
DV REPLACEMENT BLOWER (see fig. #7) .................. 21 A
RHEOSTAT C/W RETAINING NUT ............................... 22
RHEOSTAT KNOB ......................................................... 23
SNAP DISC SWITCH (see fig. #7) ................................. 24
BLOWER WIRING HARNESS (not shown) ................... 25
CORD (not shown) ......................................................... 26
CORD STRAIN RELIEF (not shown) ............................. 27
CONTROL PANEL ......................................................... 28 A
ROTARY IGNITER ......................................................... 29
IGNITER KNOB .............................................................. 30
GAS CONTROL VALVE - NAT. GAS ............................. 31
DV BURNER CONTROL VALVE - NAT. GAS ............... 33 A
GAS CONTROL KNOB .................................................. 35
GAS CONTROL KNOB EXTENSION ............................ 36
BURNER CONTROL KNOB ........................................... 37
CONNECTOR FITTING .................................................. 38
FLEX INLET PIPE (not shown) ...................................... 39 A
DV BURNER SUPPLY TUBE ......................................... 40 A
ORIFICE CONNECTOR FITTING .................................. 41
ORIFICE - DV ................................................................. 42 A
DV VENTURI TUBE ....................................................... 44 A
VENTURI GASKET ........................................................ 45
DV BURNER ASSEMBLY .............................................. 46 A
PILOT ASSEMBLY - NAT. GAS ..................................... 47
PILOT ORIFICE - NAT. GAS .......................................... 49
THERMOPILE ................................................................ 51
PILOT SUPPLY TUBE .................................................... 52
BUSHING ....................................................................... 53
WIRE STRAIN RELIEF (not shown) .............................. 54
CONTROL BRACKET .................................................... 56
1/4 SPACER ................................................................... 58
CONTROL PANEL BRACKET ....................................... 59
3/8 SPACER ................................................................... 60
PEDESTAL ..................................................................... 62 A
PEDESTAL BASE .......................................................... 64
REPLACEMENT PARTS
Fig. # 17 and 18
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)
DESCRIPTION PART NO. DESCRIPTION PART NO.
All parts may be ordered from your nearest Pacific Energy Gas Stove dealer. Contact Pacific
Energy for the location of the dealer nearest you.
fire-parts.com

15
Fig. # 17
fire-parts.com

16
Fig. # 18
fire-parts.com

17
-NOTES-
fire-parts.com

Pacific Energy Gas Stoves
Box 29, 1394 Fisher Road
Cobble Hill, B.C. V0R 1L0
Rev. #2 0793 Printed in Canada
fire-parts.com