MISURA MA05 User manual
MA05
USER GUIDE
Wireless charging mobile holder
ENGLISH
User guide
Benutzerhandbuch
Uživatelská příručka
Používateľská príručka
Használati kézikönyv
Priročnik za uporaboi
Instrukcja obsługi
Manuale d‘uso
DE
EN
HU
PL
SL
IT
SK
CZ
INSTRUCTIONS FOR USE
1. Before using this MISURA MA05 mobile holder, connect the cable via
the USB-C connector to acharging interface (for example: car charger
cigarette lighter or USB charging interface in the car).
2. Attach the mobile phone holder to the air vent grille, dashboard or car
glass using one of the supplied brackets (the mobile phone holder
can also be attached to any smooth surface, for example atable, using
asmall metal stand with double-sided tape).
3. When the MISURA MA05 mobile phone holder is connected to
a5–12 V/DC power supply, the blue indicator lights up. When you press
the centre of the back of the mobile phone against the suction cup of
the mobile phone holder, the internal micro air pump will automatically
start to create avacuum. This causes the phone to clamp firmly to the
MISURA MA05 holder and wireless charging starts.
4. When removing the phone, press and hold the suction switch on the
side of the phone holder. The phone will release, and you can remove it.
5. The MISURA MA05 cell phone holder has abuilt-in micro lithium
battery that can attach the cell phone without connecting acable.
However, in this case, wireless charging will not start (the built-in
battery does not support wireless charging function).
EN
INDICATION OF INTERNAL BATTERY STATUS
The built-in indicator shows the battery charge level:
• The blue light flashes four times continuously to indicate afully charged
product battery (equivalent to 4 bars of power)
• Blue light flashes 3 times continuously, indicating amedium battery
charge (equivalent to 3 lines of energy)
• The blue light flashes 2 times continuously, indicating alow product
battery (equivalent to 2 energy cells).
• The blue light flashes continuously 1 time, indicating anearly depleted
product battery (equivalent to 1 line of energy).
PRODUCT DESCRIPTION
1. The MISURA MA05 mobile phone holder uses the principle of electric
vacuum adsorption.
2. The mobile phone holder is equipped with an intelligent vacuum level
detection chip. This is automatically activated when the phone is placed
on the suction cup of the mobile phone holder. An internal vacuum
sensing device withsenses the vacuum strength in real time. When the
pressure is lower than the set value, the air pump immediately restarts
to ensure sufficient pressure for long-term air adsorption. This ensures
that the vacuum pressure value is constant and stable.
3. The MISURA MA05 mobile phone holder has abuilt-in wireless fast
charging function. It supports wireless charging of mobile phones and
other devices that conform to the WPC QI standard, such as the Apple
series and Android series.Apple ařady Android.
Underpressure
-60kPa
ATTENTION
1. It is recommended to use QCQ3.0 or higher adapter to power
this product.
2. Protect this product from fire and do not drop it.
3. The charging contact surface on the back of the mobile phone must
be free of metallic substances such as metal rings, uneven protective
covers, etc.
4. Do not use the wireless charger in an environment with significantly
high temperature or humidity.
5. Regularly clean the touch surface on the holder so that the phone can
be fully attached to the mobile phone holder.
6. The company assumes no liability for damages or maintenance if
damage to the device or this product occurs due to improper use,
arbitrary disassembly or failure to follow these instructions for use.
EN
PARAMETERS
Main Material: High quality aluminum alloy + PC + silicone
Supported models: Smartphones over 4 inches (MISURA MA05 mobile
phone holder does not support breathable case materials
or non-uniform mobile phone cases)
Charging interface: Type C
Battery capacity: 90 mA (built-in battery only works for air pump)
Input voltage: 5V/9V/12V+5 % (can support QC, PD protocol adapter)
Rechargeable current: 2A
Wireless charging power: 5W/7.5W/10W/15W (backward compatible)
Conversion efficiency: > 73 %
The product is equipped with overheat protection, which automatically
stops charging if the temperature is above 60° during charging.
The product is equipped with over-current protection that automatically
stops charging when the output current is higher than 2.5 Aduring
charging, to prevent damage to the charger.
Charging standard: QI wireless charging protocol
Underpressure: MIN -20kPa ~ MAX -40kPa Product size: 60×60×85mm
Product weight: 97 g
EN
insert data
cable
the mobile
phone is aimed
at sucker
center position
to take out
the phone,
press and hold
the exhaust
switch
Manufacturer/Importer
MISURA Store s.r.o.,
ID: CZ264 03 714
www.misura.shop
info@misura.shop
Thank you for your purchase.
Please contact us at:
@SHOPMisura @misura_shop @MISURA
We are not responsible for any typographical errors.
Table of contents
