Mitsubishi Electric MXZ-2HJ40VA User manual

Split-type Air-Conditioner
MXZ-2HJ40VA
Türkçe
English
Installation Manual For INSTALLER
• This manual only describes the installation of outdoor unit.
When installing the indoor unit, refer to the installation manual of indoor unit.
Kurulum Kılavuzu TESİSATÇIİÇİN
• Bukılavuzdayalnızcadışüniteninkurulumuaçıklanmaktadır.
 İçünitekurulumişleminiyaparkeniçünitekurulumkılavuzunabakın.
English is original.
Orijinalinçevirisi
BH79A129H01_en-tr_cover.indd 1 10/31/2014 9:57:45 AM

En-1
1. BEFORE INSTALLATION
1-1. THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY
• Besuretoread“THEFOLLOWINGSHOULDALWAYSBEOBSERVEDFORSAFETY”beforeinstallingtheairconditioner.
• Besuretoobservethewarningsandcautionsspeciedhereastheyincludeimportantitemsrelatedtosafety.
• Afterreadingthismanual,besuretokeepittogetherwiththeOPERATINGINSTRUCTIONSforfuturereference.
1-2. SPECIFICATIONS
nDo not install the unit by yourself (user).
 Incompleteinstallationcouldcausereorelectricshock,injuryduetotheunit
falling,orleakageofwater.Consultthedealerfromwhomyoupurchased
theunitoraqualiedinstaller.
nPerform the installation securely referring to the installation manual.
 Incompleteinstallationcouldcausere,electricshock,injuryduetothe
unitfalling,orleakageofwater.
nWhen installing the unit, use appropriate protective equipment and
tools for safety.
 Failuretodosocouldcauseinjury.
nInstall the unit securely in a place which can bear the weight of the
unit.
 Iftheinstallationlocationcannotbeartheweightoftheunit,theunitcould
fallcausinginjury.
n Electrical work should be performed by a qualied, experienced electri-
cian, according to the installation manual. Be sure to use an exclusive
circuit. Do not connect other electrical appliances to the circuit.
 If the capacity of the power circuit is insufcient or there is incomplete
electricalwork,itcouldresultinareoranelectricshock.
n Do not damage the wires by applying excessive pressure with parts
or screws.
 Damagedwirescouldcausereorelectricshock.
n Be sure to cut off the main power in case of setting up the indoor P.C.
board or wiring works.
 Failuretodosocouldcauseelectricshock.
n Use the specied wires to connect the indoor and outdoor units
securely and attach the wires rmly to the terminal block connecting
sections so the stress of the wires is not applied to the sections. Do
not extend the wires, or use intermediate connection.
 Incompleteconnectingandsecuringcouldcausere.
n Do not install the unit in a place where inammable gas may leak.
 Ifgasleaksandaccumulatesintheareaaroundtheunit,itcouldcausean
explosion.
n Do not use intermediate connection of the power cord or the extension
cord and do not connect many devices to one AC outlet.
 Itcouldcauseareoranelectricshockduetodefectivecontact,defective
insulation,exceedingthepermissiblecurrent,etc.
n Be sure to use the parts provided or specied parts for the installation
work.
 Theuseofdefectivepartscouldcauseaninjuryorleakageofwaterdue
toare,anelectricshock,theunitfalling,etc.
n When plugging the power supply plug into the outlet, make sure that
there is no dust, clogging, or loose parts in both the outlet and the
plug. Make sure that the power supply plug is pushed completely into
the outlet.
 Ifthereisdust,clogging,orloosepartsonthepowersupplyplugorthe
outlet,itcouldcauseelectricshockorre.Ifloosepartsarefoundonthe
powersupplyplug,replaceit.
n Attach the electrical cover to the indoor unit and the service panel
to the outdoor unit securely.
 Iftheelectricalcoveroftheindoorunitand/ortheservicepanelofthe
outdoorunitarenotattachedsecurely,itcouldresultinareoranelectric
shockduetodust,water,etc.
n When installing, relocating, or servicing the unit, make sure that no
substance other than the specied refrigerant (R410A) enters the
refrigerant circuit.
 Anypresenceofforeignsubstancesuchasaircancauseabnormalpres-
sureriseandmayresultinexplosionorinjury.Theuseofanyrefrigerant
otherthanthatspeciedfor thesystemwill causemechanical failure,
systemmalfunction,orunitbreakdown.Intheworstcase,thiscouldlead
toaseriousimpedimenttosecuringproductsafety.
n Do not discharge the refrigerant into the atmosphere. If refrigerant
leaks during installation, ventilate the room.
 Ifrefrigerantcomesincontactwithare,harmfulgascouldbegener-
ated.Refrigerantleakagemaycausesuffocation.Provideventilationin
accordancewithEN378-1.
n Check that the refrigerant gas does not leak after installation has
been completed.
 Ifrefrigerantgasleaksindoors,andcomesintocontactwiththeame
ofa fan heater,space heater, stove,etc.,harmful substances willbe
generated.
n Use appropriate tools and piping materials for installation.
 ThepressureofR410Ais1.6timesmorethanR22.Notusingappropriate
toolsormaterialsandincompleteinstallationcouldcausethepipesto
burstorinjury.
n When pumping down the refrigerant, stop the compressor before
disconnecting the refrigerant pipes.
 Iftherefrigerantpipesaredisconnectedwhilethecompressorisrunning
andthestopvalveisopen,aircouldbedrawninandthepressureinthe
refrigerationcyclecouldbecomeabnormallyhigh.Thiscouldcausethe
pipestoburstorinjury.
n When installing the unit, securely connect the refrigerant pipes
before starting the compressor.
 Ifthecompressorisstartedbeforetherefrigerantpipesareconnected
andwhenthestopvalveisopen,aircouldbedrawninandthepressure
intherefrigerationcyclecouldbecomeabnormallyhigh.Thiscouldcause
thepipestoburstorinjury.
n Fasten a are nut with a torque wrench as specied in this manual.
 Iffastenedtootight,aarenutmaybreakafteralongperiodandcause
refrigerantleakage.
n The unit shall be installed in accordance with national wiring regula-
tions.
nEarth the unit correctly.
 Donotconnecttheearthtoagaspipe,waterpipe,lightningrodortele-
phoneearth.Defectiveearthingcouldcauseelectricshock.
nBe sure to install an earth leakage breaker.
 Failuretoinstallanearthleakagebreakermayresultinelectricshockor
re.
nPerform the drainage/piping work securely according to the installation
manual.
 Ifthereisdefectinthedrainage/pipingwork,watercoulddropfromtheunit,
soakinganddamaginghouseholdgoods.
n Do not touch the air inlet or the aluminum ns of the outdoor unit.
 Thiscouldcauseinjury.
nDo not install the outdoor unit where small animals may live.
 Ifsmallanimalsenterandtouchtheelectricpartsinsidetheunit,itcould
causeamalfunction,smokeemission,orre.Also,adviseusertokeep
theareaaroundtheunitclean.
WARNING (Couldleadtodeath,seriousinjury,etc.)
*1 Connecttothepowerswitchwhichhasagapof3mmormorewhenopen
tointerruptthesourcepowerphase.(Whenthepowerswitchisshutoff,it
mustinterruptallphases.)
*2 Usewiresinconformitywithdesign60245IEC57.Usetheindoor/outdoor
connectingwireinconformitywiththewirespecicationsspeciedinthe
installationmanualoftheindoorunit.
*3 Neverusepipeswiththicknesslessthanspecied.Thepressureresistance
willbeinsufcient.
*4 Useacopperpipeoracopper-alloyseamlesspipe.
*5 Becarefulnottocrushorbendthepipeduringpipebending.
*6 Refrigerantpipebendingradiusmustbe100mmormore.
*7 Insulationmaterial:Heatresistingfoamplastic0.045specicgravity
*8 Besuretousetheinsulationofspeciedthickness.Excessivethickness
maycauseincorrectinstallationoftheindoorunitandinsufcientthickness
maycausedewdrippage.
* 9  Iftheoutdoorunitisinstalledhigherthantheindoorunit,max.height
differenceisreducedto10m.
* 10 Ifpipelengthexceeds20m,additionalrefrigerant(R410A)chargeisre-
quired.(Noadditionalchargeisrequiredforpipelengthlessthan20m.)
 Additionalrefrigerant=A×(pipelength(m)-20)
Required Tools for Installation
Phillipsscrewdriver
Level
Scale
Utilityknifeorscissors
Torquewrench
Wrench(orspanner)
4mmhexagonalwrench
FlaretoolforR410A
GaugemanifoldforR410A
VacuumpumpforR410A
ChargehoseforR410A
Pipecutterwithreamer
ENGLISH
CONTENTS
1.BEFOREINSTALLATION............................................................1
2.OUTDOORUNITINSTALLATION...............................................3
3.FLARINGWORKANDPIPECONNECTION...............................3
4.PURGINGPROCEDURES,LEAKTEST,ANDTESTRUN.........4
5.PUMPINGDOWN........................................................................5
Model
Powersupply*1 Wirespecications*2 Pipelengthandheightdifference
*3,*4,*5,*6,*7,*8 OutdoorNoiselevel
Rated
Voltage
Fre-
quency
Breaker
capacity Powersupply
Indoor/
outdoorcon-
nectingwire
Max.pipe
lengthper
indoorunit/for
multi-system
Max.height
difference
*9
Max.no.of
bendsper
indoorunit/for
multisystem
Refrigerant
adjustment
A*10
Cooling Heating
MXZ-2HJ40VA 230V 50Hz 15A 3-core2.0mm24-core
1.0/1.5mm220m/30m 15m 20/30 20g/m 48dB(A) 52dB(A)
CAUTION (Couldleadtoseriousinjuryinparticularenvironmentswhenoperatedincorrectly.)
BH79A129H01_en.indd 1 10/31/2014 9:57:26 AM

En-2
*2
*2
*2
1-3. SELECTING OPTIONAL DIFFERENT-DIAMETER JOINTS
If the diameter of connection pipe does not match the port size of outdoor unit, use optional different-diameter joints according to the following table.
Port size of outdoor unit Optional different-diameter joints (port size of outdoor unit → diameter of connection pipe)
MXZ-2HJ40VA Liquid / Gas 6,35 (1/4) → 9,52 (3/8) : PAC-493PI
9,52 (3/8) → 12,7 (1/2) : MAC-A454JP
9,52 (3/8) → 15,88 (5/8) : PAC-SG76RJ
12,7 (1/2) → 9,52 (3/8) : MAC-A455JP
12,7 (1/2) → 15,88 (5/8) : MAC-A456JP
Refer to the installation manual of indoor unit for the diameter of connection pipe of indoor unit.
A , B UNIT 6,35 (1/4) / 9,52 (3/8)
1-4. SELECTING THE INSTALLATION LOCATION
• Where it is not exposed to strong wind.
• Where airow is good and dustless.
• Where rain or direct sunshine can be avoided as much as possible.
• Where neighbours are not annoyed by operation sound or hot air.
• Where rigid wall or support is available to prevent the increase of opera-
tion sound or vibration.
• Where there is no risk of combustible gas leakage.
• When installing the unit, be sure to secure the unit legs.
• Where it is at least 3 m away from the antenna of TV set or radio. Opera-
tion of the air conditioner may interfere with radio or TV reception in areas
where reception is weak. An amplier may be required for the affected
device.
• Install the unit horizontally.
• Please install it in an area not affected by snowfall or blowing snow. In
areas with heavy snow, please install a canopy, a pedestal and/or some
bafe boards.
Note:
It is advisable to make a piping loop near outdoor unit so as to reduce
vibration transmitted from there.
(Unit: mm (inch))
1-5. INSTALLATION DIAGRAM
ACCESSORIES
Check the following parts before installation.
(1) Drain socket 1
PARTS TO BE PROVIDED AT YOUR SITE
(A) Power supply cord*1 1
(B)
Indoor/outdoor unit connecting wire*1 1
(C) Extension pipe 1
(D) Wall hole cover 1
(E) Piping tape 1
(F)
Extension drain hose
(or soft PVC hose, 15 mm inner
diameter or hard PVC pipe VP16)
1
(G) Refrigeration oil Little
amount
(H) Putty 1
(I) Pipe xing band 2 to 7
(J) Fixing screw for (I) 2 to 7
(K) Wall hole sleeve 1
(L)
Soft PVC hose, 15 mm inner
diameter or hard PVC pipe VP16
for drain socket (1)
1
Note:
*1 Place indoor/outdoor unit connecting wire (B) and
power supply cord (A) at least 1 m away from the
TV antenna wire.
The “Q’ty” for (B) to (K) in the above table is quan-
tity to be used per indoor unit.
Units should be installed by licensed contractor according to local code requirements.
More than
100 mm
More than 100 mm
More than 200 mm if there are
obstacles to both sides
Open as a rule
More than 500 mm if the back,
both sides and top are open More than 350 mm
Outdoor unit installation
(Unit: mm)
285
Air inlet
150 500
Air inlet
4-10 × 21 Oval holes
304~325
344.5
Air outlet
800
Open as a rule
More than 500 mm if the front
and both sides are open
Note:
When operating the air conditioner in low outside temperature, be sure
to follow the instructions described below.
• Never install the outdoor unit in a place where its air inlet/outlet side
may be exposed directly to wind.
• To prevent exposure to wind, install the outdoor unit with its air inlet
side facing the wall.
•
To prevent exposure to wind, it is recommended to install a bafe board
on the air outlet side of the outdoor unit.
Avoid the following places for installation where air conditioner trouble
is liable to occur.
• Where ammable gas could leak.
• Where there is much machine oil.
• Where oil is splashed or where the area is lled with oily smoke (such
as cooking areas and factories, in which the properties of plastic could
be changed and damaged).
• Salty places such as the seaside.
• Where sulde gas is generated such as a hot spring.
• Where there is high-frequency or wireless equipment.
• Where there is emission of high levels of VOCs, including phthalate
compounds, formaldehyde, etc., which may cause chemical cracking.
*2 The manufacturing year and month is indicated on the spec
name plate.
When the piping is to be attached
to a wall containing metals (tin
plated) or metal netting, use a
chemically treated wooden piece
20 mm or thicker between the wall
and the piping or wrap 7 to 8 turns
of insulation vinyl tape around
the piping.
To use existing piping, perform
COOL operation for 30 minutes
and pump down before removing
the old air conditioner. Remake
are according to the dimension
for new refrigerant.
After the leak test, apply insulat-
ing material tightly so that there
is no gap.
BH79A129H01_en.indd 2 10/31/2014 11:29:48 AM

En-3
LN
LN
LN
LN
1-6. DRAIN PIPING FOR OUTDOOR UNIT
Pleaseperformthedrainpipingworkonlywhendrainingfromoneplace.
1)Providedrainpipingbeforeindoorandoutdoorpipingconnection.
2)ConnectthesoftPVChose(L)I.D.15mmasshownintheillustration.
3)Makesuretoprovidedrainpipingwithadownhillgradeforeasydrainow.
Note:
Installtheunithorizontally.
Donotusethedrainsocket(1)inthecoldregions.Drainmayfreezeanditmakes
thefanstop.
Theoutdoorunitproducescondensateduringtheheatingoperation.Selecttheinstal-
lationplacetoensuretopreventtheoutdoorunitand/orthegroundsfrombeingwet
bydrainwaterordamagedbyfrozendrainwater.
(1)Drainsocket (L)SoftPVChose
2-1. CONNECTING WIRES FOR OUTDOOR UNIT
• Be sure to attach each screw to its
correspondentterminalwhensecuring
thecordand/orthewiretotheterminal
block.
• Makeearthwirealittlelongerthanoth-
ers.(Morethan35mm)
• Forfutureservicing,giveextralength
totheconnectingwires.
Terminalblockforpowersupply
1)Removetheservicepanel.
2)Loosenterminalscrew,andconnectindoor/outdoorunitconnectingwire
(B)fromtheindoorunitcorrectlyontheterminalblock.Becarefulnot
tomakemis-wiring.Fixthewiretotheterminalblocksecurelysothat
nopartofitscoreisappeared,andnoexternalforceisconveyedtothe
connectingsectionoftheterminalblock.
3)Firmlytightentheterminalscrewstopreventthemfromloosening.After
tightening,pullthewireslightlytoconrmthattheydonotmove.
4)Perform2)and3)foreachindoorunit.
5)Connectpowersupplycord(A).
6)Fixindoor/outdoorunitconnectingwire(B)andpowersupplycord(A)
withthecableclamps.
7)Closetheservicepanelsecurely.Makesurethat3-2.PIPECONNEC-
TIONiscompleted.
• Aftermakingconnectionsbetweenbothpowersupplycord(A)andindoor/
outdoorunitconnectingwire(B),besuretoxbothcableandwirewith
cableclamps.
Indoor/outdoorunitconnectingwire <OUTDOORUNIT>
35mm
15mm
Leadwire
Terminalblock
UNIT UNIT
Terminalblockfor
powersupply
<INDOORUNIT>
POWERSUPPLY
~/N230V50Hz
Servicepanel
Fig.1 Fig.2
Fig.3 Fig.4
Fig.5 Fig.6
3-1. FLARING WORK
Pipediameter
(mm)
Nut
(mm)
A(mm) Tighteningtorque
Clutch
typetool
forR410A
Clutch
typetool
forR22
Wingnut
typetool
forR22
N•m kgf•cm
ø6.35(1/4”) 17
0to0.5 1.0to1.5
1.5to2.0 13.7to17.7 140to180
ø9.52(3/8”) 22 34.3to41.2 350to420
ø12.7(1/2”) 26 2.0to2.5 49.0to56.4 500to575
ø15.88(5/8”) 29 73.5to78.4 750to800
TiltedUnevenBurred
Good Nogood
Burr Copperpipe
Sparereamer
Pipecutter
Smoothall
around
Evenlength
allaround
Insideisshin-
ingwithoutany
scratches.
Flarenut
Die Copperpipe
Clutchtype
Flaringtool
Wingnuttype
Copper
pipe
1)Cutthecopperpipecorrectlywithpipecutter.(Fig.1,2)
2)Completelyremoveallburrsfromthecutcrosssectionofpipe.(Fig.3)
• Aimthecopperpipedownwardwhileremovingburrstopreventburrs
fromdroppinginthepipe.
3)Removearenutsattachedtoindoorandoutdoorunits,thenputthem
onpipehavingcompletedburrremoval.(Notpossibletoputthemon
afteraringwork.)
4)Flaringwork(Fig.4,5).Firmlyholdcopperpipeinthedimensionshown
inthetable.SelectAmmfromthetableaccordingtothetoolselected.
5)Check
• ComparethearedworkwithFig.6.
• Ifareisnotedtobedefective,cutoffthearedsectionanddoaring
workagain.
3. FLARING WORK AND PIPE CONNECTION
2. OUTDOOR UNIT INSTALLATION
BH79A129H01_en.indd 3 10/31/2014 9:57:27 AM

En-4
4-1. PURGING PROCEDURES AND LEAK TEST
3-2. PIPE CONNECTION
1)Applyathincoatofrefrigerationoil(G)tothearedendsofthepipesandthepipeconnectionsoftheoutdoor
unit.
2)Alignthecenterofthepipewiththatofthepipeconnectionsoftheoutdoorunit,thenhandtightentheare
nut3to4turns.
3)Tightenthearenutwithatorquewrenchasspeciedinthetable.
•Over-tighteningmaycausedamagetothearenut,resultinginrefrigerantleakage.
•Besuretowrapinsulationaroundthepiping.Directcontactwiththebarepipingmayresultinburnsorfrostbite.
3-3. INSULATION AND TAPING
1)Coverpipingjointswithpipecover.
2)Foroutdoorunitside,surelyinsulateeverypipingincludingvalves.
3)Usingpipingtape(E),applytapingstartingfromtheentryofoutdoorunit.
• Stoptheendofpipingtape(E)withtape(withadhesiveagentattached).
• Whenpipinghavetobearrangedthroughaboveceiling,closetorwherethetemperatureandhumidityare
high,windadditionalcommerciallysoldinsulationtopreventcondensation.
1)Removeserviceportcapofstopvalveonthesideoftheoutdoorunit
gaspipe.(Thestopvalvesarefullyclosedandcoveredincapsin
theirinitialstate.)
2)Connectgaugemanifoldvalveandvacuumpumptoserviceportof
stopvalveonthegaspipesideoftheoutdoorunit.
3)Runthevacuumpump.(Vacuumizeformorethan15minutes.)
4)Check the vacuum with gauge manifold valve, then close gauge
manifoldvalve,andstopthevacuumpump.
5)Leaveasitisforoneortwominutes.Makesurethepointerofgauge
manifoldvalveremainsinthesameposition.Conrmthatpressure
gaugeshows-0.101MPa[Gauge](-760mmHg).
6)Removegaugemanifoldvalvequicklyfromserviceportofstopvalve.
7)Fullyopenallstopvalvesonthegaspipeandtheliquidpipe.Operating
withoutfullyopeninglowerstheperformanceandthiscausestrouble.
8)Refer to 1-2., and charge the prescribed amount of refrigerant if
needed.Besuretochargeslowlywithliquidrefrigerant.Otherwise,
compositionoftherefrigerantin thesystemmaybechangedand
affectperformanceoftheairconditioner.
9)Tightencapofserviceporttoobtaintheinitialstatus.
10 )Leaktest
WARNING
When installing the unit, securely
connect the refrigerant pipes before
starting the compressor.
CAUTION
When there are the ports which are
not used, make sure their nuts are
tightened securely.
Stopvalve
forGAS
Stopvalve
cap(Torque
19.6to29.4
N•m,200to
300kgf•cm)
Gaugemanifold
valve(forR410A)
Compoundpressure
gauge(forR410A)
–0.101MPa
(–760mmHg)
Handle
Low
HandleHigh
Vacuumpump
(forR410A)
*Close
*Open
Hexagonalwrench
*4to5turns
Stopvalve
forLIQUID
Pressuregauge
(forR410A)
Precautionswhenus-
ingthecontrolvalve
Whenattachingthecontrolvalve
totheserviceport,valvecoremay
deformorloosenifexcesspres-
sureisapplied.Thismaycause
gasleak.
Service
port
Chargehose
(forR410A)
Body
Close
Open
Control
valve
A
Whenattachingthecontrolvalveto
theserviceport,makesurethatthe
valvecoreisinclosedposition,and
then tighten partA. Do not tighten
partAorturnthebodywhenvalve
coreisinopenposition.
Serviceportcap
(Torque13.7to17.7
N•m,140to180kgf•cm)
Chargehose
(forR410A)
4-2. GAS CHARGE
Performgaschargetounit.
1)Connectgascylindertotheserviceportofstopvalve.
2)Performairpurgeofthepipe(orhose)comingfromrefrigerantgascylinder.
3)Replenishspeciedamountoftherefrigerant,whileoperatingtheairconditioner
forcooling.
Note:
Incaseofaddingrefrigerant,complywiththequantityspeciedfortherefrigerat-
ingcycle.
CAUTION:
Whenchargingtherefrigerantsystemwithadditionalrefrigerant,besuretouse
liquidrefrigerant.Addinggasrefrigerantmaychangethecompositionoftherefriger-
antinthesystemandaffectnormaloperationoftheairconditioner.Also,charge
theliquidrefrigerantslowly,otherwisethecompressorwillbelocked.
To maintain the high pressure of the gas cylinder, warm the gas cylinder with
warmwater(under40°C)duringcoldseason.Butneverusenakedreorsteam.
Refrigerantgas
cylinder
operatingvalve
(forR410A)
Indoor
unit
Chargehose(forR410A)
Refrigerantgascylinder
forR410Awithsiphon
Electronicscalefor
refrigerantcharging
Refrigerant(liquid)
Indoor
unit
Union
Union
Liquidpipe
Gaspipe
Liquidpipe
Gaspipe
Stopvalve
Serviceport
Outdoor
unit
Gaugemanifold
valve(forR410A)
4. PURGING PROCEDURES, LEAK TEST, AND TEST RUN
BH79A129H01_en.indd 4 10/31/2014 9:57:27 AM

En-5
4-3. LOCKING THE OPERATION MODE OF THE AIR CONDITIONER (COOL, DRY, HEAT)
4-4. LOWERING THE OPERATION NOISE OF THE OUTDOOR UNIT
• Descriptionofthefunction:
 Withthisfunction,oncetheoperationmodeislockedtoeitherCOOL/DRYmode
orHEATmode,theairconditioneroperatesinthatmodeonly.
* Changingthesettingisrequiredtoactivatethisfunction.Pleaseexplainabout
thisfunctiontoyourcustomersandaskthemwhethertheywanttouseit.
[How to lock the operation mode]
1)Besuretoturnoffthemainpowerfortheairconditionerbefore makingthe
setting.
2)Setthe“1”ofSW1ontheoutdoordisplayboardtoONtoenablethisfunction.
3)TolocktheoperationmodeinCOOL/DRYmode,setthe“2”ofSW1onthe
outdoordisplayboardtoOFF.TolocktheoperationinHEATmode,setthe
sameswitchtoON.
4)Turnonthemainpowerfortheairconditioner.
• Descriptionofthefunction:
 Withthisfunction,theoperatingnoiseoftheoutdoorunitcanbeloweredbyreducingtheoperationload,forexample,duringnighttimeinCOOLmode.
However,pleasenotethatthecoolingandheatingcapacitymaylowerifthisfunctionisactivated.
* Changingthesettingisrequiredtoactivatethisfunction.Pleaseexplainaboutthisfunctiontoyourcustomersandaskthemwhethertheywanttouseit.
Lowertheoperatingnoise
[How to lower the operating noise]
1)Besuretoturnoffthemainpowerfortheairconditionerbefore makingthe
setting.
2)Setthe“3”ofSW1ontheoutdoordisplayboardtoONtoenablethisfunction.
3)Turnonthemainpowerfortheairconditioner.
4-5. TEST RUN
• Testrunsoftheindoorunitsshouldbeperformedindividually.Seetheinstallationmanualcomingwiththeindoorunit,andmakesurealltheunitsoperate
properly.
• Ifthetestrunwithalltheunitsisperformedatonce,possibleerroneousconnectionsoftherefrigerantpipesandtheindoor/outdoorunitconnectingwires
cannotbedetected.Thus,besuretoperformthetestrunonebyone.
Makesurethatthefollowingisdone.
• Powerissuppliedtotheunit.
• Stopvalvesareopen.
About the restart protective mechanism
Oncethecompressorstops,therestartpreventivedeviceoperatessothecompressorwillnotoperatefor3minutestoprotecttheairconditioner.
Whenrelocatingordisposingoftheairconditioner,pumpdownthesystemfollowingtheprocedurebelowsothatnorefrigerantisreleasedintotheatmosphere.
1)Turnoffthebreaker.
2)Connectthegaugemanifoldvalvetotheserviceportofthestopvalveonthegaspipesideoftheoutdoorunit.
3)Fullyclosethestopvalveontheliquidpipesideoftheoutdoorunit.
4)Turnonthebreaker.
5)StarttheemergencyCOOLoperationonalltheindoorunits.
6)Whenthepressuregaugeshows0.05to0MPa[Gauge](approx.0.5to0kgf/cm2),fullyclosethestopvalveonthegaspipesideoftheoutdoorunitand
stoptheoperation.(Refertotheindoorunitinstallationmanualaboutthemethodforstoppingtheoperation.)
 * Iftoomuchrefrigeranthasbeenaddedtotheairconditionersystem,thepressuremaynotdropto0.05MPa[Gauge](approx.0.5kgf/cm2),ortheprotec-
tionfunctionmayoperateduetothepressureincreaseinthehigh-pressurerefrigerantcircuit.Ifthisoccurs,usearefrigerantcollectingdevicetocollect
alloftherefrigerantinthesystem,andthenrechargethesystemwiththecorrectamountofrefrigerantaftertheindoorandoutdoorunitshavebeen
relocated.
7)Turnoffthebreaker.Removethepressuregaugeandtherefrigerantpiping.
When pumping down the refrigerant, stop the compressor before disconnecting the refrigerant pipes.
The compressor may burst and cause injury if any foreign substance, such as air, enters the pipes.
WARNING
4-6. EXPLANATION TO THE USER
• UsingtheOPERATINGINSTRUCTIONS,explaintotheuserhowtousetheairconditioner(howtousetheremotecontroller,howtoremovetheairlters,
howtoremoveorputtheremotecontrollerintheremotecontrollerholder,howtoclean,precautionsforoperation,etc.).
• RecommendtheusertoreadtheOPERATINGINSTRUCTIONScarefully.
COOL/DRY HEAT
5. PUMPING DOWN
BH79A129H01_en.indd 5 10/31/2014 9:57:28 AM

BH79A129H01
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
EC DECLARATION OF CONFORMITY
EG-KONFORMITÄTSERKLÄRUNG
DÉCLARATION DE CONFORMITÉ CE
EG-CONFORMITEITSVERKLARING
DECLARACIÓN DE CONFORMIDAD CE
DICHIARAZIONE DI CONFORMITÀ CE
ΔΗΛΩΣΗΠΙΣΤΟΤΗΤΑΣΕΚ
DECLARAÇÃODECONFORMIDADECE
EU-OVERENSSTEMMELSESERKLÆRING
EG-DEKLARATION OM ÖVERENSSTÄMMELSE
EC UYGUNLUK BEYANI
ДЕКЛАРАЦИЯСООТВЕТСТВИЯНОРМАМЕС
CE-ERKLÆRING OM SAMSVAR
EY-VAATIMUSTENMUKAISUUSVAKUUTUS
ДЕКЛАРАЦИЯЗАСЪОТВЕТСТВИЕ
MITSUBISHI ELECTRIC CONSUMER PRODUCTS (THAILAND) CO., LTD
AMATA NAKORN INDUSTRIAL ESTATE 700/406 MOO 7, TAMBON DON HUA ROH, AMPHUR MUANG, CHONBURI 20000, THAILAND
Note:Itsserialnumberisonthenameplateoftheproduct.
Hinweis:DieSeriennummerbendetsichaufdemKennschilddesProdukts.
Remarque:Lenumérodesériedel’appareilsetrouvesurlaplaqueduproduit.
Opmerking:hetserienummerstaatophetnaamplaatjevanhetproduct.
Nota:Elnúmerodeserieseencuentraenlaplacaquecontieneelnombredelproducto.
Nota:ilnumerodiseriesitrovasullatarghettadelprodotto.
Σημείωση:Οσειριακόςτουαριθμόςβρίσκεταιστηνπινακίδαονόματοςτουπροϊόντος.
Nota:onúmerodesérieencontra-senaplacaquecontémonomedoproduto.
Bemærk:Serienummeretstårpåproduktetsfabriksskilt.
Obs:Serienumretnnspåproduktensnamnplåt.
Not:Serinumarasıürününisimplakasındayeralır.
Примечание:серийныйномеруказаннапаспортноетабличкеизделия.
Merk:Serienummeretbennersegpånavneplatentilproduktet.
Huomautus:Sarjanumeroonmerkittylaitteenarvokilpeen.
Забележка:Серийниятмуномеренатабелкатанапродукта.
Directives
Richtlinien
Directives
Richtlijnen
Directivas
Direttive
Οδηγίες
Directivas
Direktiver
Direktiv
Direktier
Директивы
Direktiver
Direktiivit
Директиви
OurauthorizedrepresentativeinEU,whoisauthorizedtocompilethetechnicalle,isasfollows.
UnserautorisierterVertreterinderEU,derermächtigtistdietechnischenDatenzukompilieren,ist
wie folgt.
NotrereprésentantagrééedansL’UE,quiestautoriséàcompilerlechiertechnique,estlesuivant.
OnzegeautoriseerdevertegenwoordigerindeEU,diegemachtigdishettechnischebestandtecom-
pileren,isalsvolgt.
NuestrorepresentanteautorizadoenlaUE,queestáautorizadoparacompilarelarchivotécnico,es
el siguiente.
Ilnostrorivenditoreautorizzatonell’UE,responsabiledellastesuradellaschedatecnica,èilseguente.
ΟεξουσιοδοτημένοςαντιπρόσωπόςμαςστηνΕΕ,οοποίοςείναιεξουσιοδοτημένοςνασυντάξειτον
τεχνικόφάκελο,είναιοεξής.
OnossorepresentanteautorizadonaUE,queestáautorizadoparacompilarocheirotécnico,éo
seguinte:
VoresautoriserederepræsentantiEU,somerautoriserettiludarbejdelseafdentekniskel,erføl-
gende.
VårEG-representantsomärauktoriseradattsammanställadentekniskalenärföljande.
AvrupaBirliği’nde bulunan veteknik dosyayı düzenlemeyetkisine sahip yetkilitemsilcimiz aşağıda
belirtilmiştir:
НашавторизованныйпредставительвЕС,уполномоченныйнасоставлениетехническогофай-
ла,указанниже.
VårautoriserteEU-representant,somharautorisasjontilåutarbeidedennetekniskelen,ersomfølger.
ValtuutettuEU-edustaja,jokaonvaltuutettulaatimaantekniseneritelmän,onmainittualla.
НашупълномощенпредставителвЕС,койтоеупълномощендасъставитехническотодосие,
екактоследва.
MITSUBISHI ELECTRIC EUROPE, B.V.
HARMAN HOUSE, 1 GEORGE STREET, UXBRIDGE, MIDDLESEX UB8 1QQ, U.K.
Yoji SAITO
Product Marketing Director
Issued: 9, October, 2014 Tomoyuki MIWA
THAILAND Manager, Quality Assurance Department
MITSUBISHI ELECTRIC, MXZ-2HJ40VA
2006/95/EC: Low Voltage Directive
2006/42/EC: Machinery Directive
2004/108/EC: Electromagnetic Compatibility Directive
2009/125/EC: Energy-related Products Directive and Regulation (EU) No 206/2012
herebydeclaresunderitssoleresponsibilitythattheairconditionersandheatpumpsdescribedbelowforuseinresidential,commercialandlight-industrialenvironments:
erklärthiermitaufseinealleinigeVerantwortung,dassdieKlimaanlagenundWärmepumpenfürdashäusliche,kommerzielleundleicht-industrielleUmfeldwieuntenbeschrieben:
déclareparlaprésenteetsoussapropreresponsabilitéquelesclimatiseursetlespompesàchaleurdécritsci-dessous,destinésàunusagedansdesenvironnementsrésidentiels,
commerciauxetd’industrielégère:
verklaarthierbijondereigenverantwoordelijkheiddatdevoorresidentiële,commerciëleenlicht-industriëleomgevingenbestemdeairconditionersenwarmtepompenzoalsonderstaand
beschreven:
porlapresentedeclarabajosuúnicaresponsabilidadquelosacondicionadoresdeaireybombasdecalordescritasacontinuaciónparasuusoenentornosresidenciales,comerciales
y de industria ligera:
confermaconlapresente,sottolasuaesclusivaresponsabilità,cheicondizionatorid’ariaelepompedicaloredescrittidiseguitoedestinatiall’utilizzoinambientiresidenziali,commer-
ciali e semi-industriali:
μετοπαρόνπιστοποιείμεαποκλειστικήτηςευθύνηότιοιτακλιματιστικάκαιοιαντλίεςθέρμανσηςπουπεριγράφονταιπαρακάτωγιαχρήσησεοικιακό,επαγγελματικόκαιελαφριάς
βιομηχανίαςπεριβάλλοντα:
atravésdapresentedeclarasobsuaúnicaresponsabilidadequeosaparelhosdearcondicionadoebombasdecalorabaixodescritosparausoresidencial,comercialedeindústrialigeira:
erklærerhermedundereneansvar,atdeherunderbeskrevneairconditionanlægogvarmepumpertilbrugiprivatboligbyggeri,erhvervsområderogindenforletindustri:
intygarhärmedattluftkonditioneringarnaochvärmepumparnasombeskrivsnedanföranvändningibostäder,kommersiellamiljöerochlättaindustriellamiljöer:
ev,ticaretvehafsanayiortamlarındakullanımamaçlıüretilenveaşağıdaaçıklananklimaveısıtmapompalarıylailgiliaşağıdakihususlarıyalnızcakendisorumluluğundabeyaneder:
настоящимзаявляетиберетнасебяисключительнуюответственностьзато,чтокондиционерыитепловыенасосы,описанныенижеипредназначенныедляэксплуатациив
жилыхпомещениях,торговыхзалахинапредприятияхлегкойпромышленности:
erklæreretfullstendigansvarforundernevnteklimaanleggogvarmepumpervedbrukiboliger,samtkommersielleoglettindustriellemiljøer:
vakuuttaatätenyksinomaisellavastuullaan,ettäjäljempänäkuvatutasuinrakennuksiin,pienteollisuuskäyttöönjakaupalliseenkäyttööntarkoitetutilmastointilaitteetjalämpöpumput:
деклариранасвоясобственаотговорност,чеклиматицитеитермопомпите,описанипо-долу,заупотребавжилищни,търговскиилекипромишлениусловия:
BH79A129H01_en-tr_cover.indd 2 10/31/2014 9:57:45 AM