Mitsubishi Electric PQHY-P200YHM-A Product guide

DATA BOOK
AIR CONDITIONERS
MODEL
PQHY-P Y(S)HM-A
PQRY-P Y(S)HM-A
- For ground source application

i
Preface
DATABOOK describes the technical specifications of MITSUBISHI ELECTRIC Corp.'s CITYMULTI air conditioning
system products.
In this DATABOOK for ground source application, information on water-cooled heat source unit PQHY-P Y(S)HM-A/
PQRY-P Y(S)HM-A, with the connection of standard CITY MULTI indoor unit series, Air to Water series, and Close
Control PFD series are specified.
We recommend DATABOOK users to read carefully and take advantage of all the contents inside to design the CITY
MULTI air conditioning system and/or to prepare documents for promotions.
Along with the DATABOOK, MITSUBISHI ELECTRIC provides a Design-Tool software to ensure the users to design
the system correctly and simplify the calculations. Please contact your local distributor for this software.
Please be notified that specifications are subject to change without notice due to continual improvements of the prod-
uct.
For any inquiries, please contact your local distributor.

Contents
I Brine information
1. Brine freezing temperature ........................................................................................................ 1
2. Capacity correction by brine concentration (For heat source unit) ...................................... 2
3. Pressure drop correction by brine concentration (For heat source unit) ............................. 3
II Heat source unit information
1. General lineup of water-cooled heat source unit .................................................................... 4
2. PQHY-P-Y(S)HM-A ...................................................................................................................... 5
(1)Specification .............................................................................................................................................. 5
(1)-1 Heat source units specification for standard combination
(Standard CITY MULTI indoor units, PWFY-P100/200VM-E-AU) .................................................. 5
(1)-2 System specification for closed control system (PFD-P250/500VM-E) ....................................... 19
(2)External dimension .................................................................................................................................. 21
(3)Center of gravity ...................................................................................................................................... 24
(4)Electrical wiring diagram .......................................................................................................................... 25
(5)Sound levels ............................................................................................................................................ 26
(6)Capacity tables with indoor units ............................................................................................................. 30
(6)-1 Cooling capacity with standard indoor units ................................................................................. 30
(6)-2 Heating capacity with standard indoor units ................................................................................. 43
(7)Correction by total indoor ......................................................................................................................... 44
(8)Correction by refrigerant piping length ..................................................................................................... 46
(9)Correction by water temperature (For heat source unit) .......................................................................... 49
(9)-1 Connection with standard CITY MULTI indoor units .................................................................... 49
(9)-2 Connection with PWFY-P100/200VM-E-AU (HEX unit) ............................................................... 49
(9)-3 Connection with PFD-P250/500VM-E .......................................................................................... 50
(10)Correction by water flow rate (For heat source unit) .............................................................................. 51
(10)-1 Connection with standard CITY MULTI indoor units .................................................................... 51
(10)-2 Connection with PWFY-P100/200VM-E-AU (HEX unit) ............................................................... 51
(10)-3 Connection with PFD-P250/500VM-E .......................................................................................... 51
(11)Correction by indoor temperature .......................................................................................................... 52
(11)-1 Connection with standard CITY MULTI indoor units .................................................................... 52
(11)-2 Connection with PWFY-P100/200VM-E-AU (HEX unit) ............................................................... 52
(11)-3 Connection with PFD-P250/500VM-E .......................................................................................... 52
(12)Correction by water flow rate (For PWFY-P100/200VM-E-AU (HEX unit)) ............................................ 53
(12)-1 Connection with PWFY-P100VM-E-AU (HEX unit) ...................................................................... 53
(12)-2 Connection with PWFY-P200VM-E-AU (HEX unit) ...................................................................... 53
(13)Water pressure drop correction by water volume ................................................................................. 54
(13)-1 Heat source unit correction
(Connection with Standard CITY MULTI indoor units, PWFY-P100/200VM-E-AU,
PFD-P250/500VM-E) ................................................................................................................... 54
(13)-2 HEX unit correction (Connection with PWFY-P100/200VM-E-AU) .............................................. 54
(13)-3 Water pressure drop of strainer only (accessory for PWFY-P100/200VM-E-AU) ........................ 54
(14)Operation temperature range ................................................................................................................ 55
(14)-1 Connection with standard CITY MULTI indoor units .................................................................... 55
(14)-2 Connection with PWFY-P100/200VM-E-AU (HEX unit) ............................................................... 55
(14)-3 Connection with PFD-P250/500VM-E .......................................................................................... 56
(15)Piping design ......................................................................................................................................... 57
(15)-1 R410A Piping material .................................................................................................................. 57
(15)-2 PQHY-P200-300YHM Piping
(Connection with standard CITY MULTI indoor units, PWFY-P100/200VM-E-AU) ...................... 58
(15)-3 PQHY-P400-600YSHM Piping
(Connection with standard CITY MULTI indoor units, PWFY-P100/200VM-E-AU) ...................... 59
(15)-4 PQHY-P650-900YSHM Piping
(Connection with standard CITY MULTI indoor units, PWFY-P100/200VM-E-AU) ...................... 60
(15)-5 PQHY-P250/P250+P250YHM
(Connection with PFD indoor unit) ............................................................................................... 61
(15)-6 Refrigerant charging calculation ................................................................................................... 62

3. PQRY-P-Y(S)HM-A .................................................................................................................... 63
(1)Specification ............................................................................................................................................ 63
(1)-1 Heat source units specification for standard combination
(Standard CITY MULTI indoor units, PWFY-P100VM-E-BU, PWFY-P100/200VM-E-AU) .......... 63
(2)External dimension .................................................................................................................................. 71
(3)Center of gravity ...................................................................................................................................... 73
(4)Electrical wiring diagram .......................................................................................................................... 74
(5)Sound levels ............................................................................................................................................ 75
(6)Capacity tables with indoor units ............................................................................................................. 77
(6)-1 Cooling capacity with standard indoor units ................................................................................. 77
(6)-2 Heating capacity with standard indoor units ................................................................................. 90
(7)Correction by total indoor ......................................................................................................................... 91
(8)Correction by refrigerant piping length ..................................................................................................... 92
(9)Correction by port counts of the BC controller ........................................................................................ 93
(10)Correction by water temperature (For heat source unit) ........................................................................ 94
(10)-1 Connection with standard CITY MULTI indoor units .................................................................... 94
(10)-2 Connection with PWFY-P100/200VM-E-AU (HEX unit) ................................................................ 94
(10)-3 Connection with PWFY-P100VM-E-BU (Booster unit) ................................................................. 95
(10)-4 Connection with PWFY-P100VM-E-BU (Booster unit) + WCB Energy saving mode* ................. 96
(11)Correction by water flow rate (For heat source unit) .............................................................................. 97
(11)-1 Connection with standard CITY MULTI indoor units .................................................................... 97
(11)-2 Connection with PWFY-P100/200VM-E-AU (HEX unit) ............................................................... 97
(11)-3 Connection with PWFY-P100VM-E-BU (Booster unit) ................................................................. 97
(12)Correction by indoor temperature .......................................................................................................... 98
(12)-1 Connection with standard CITY MULTI indoor units .................................................................... 98
(12)-2 Connection with PWFY-P100/200VM-E-AU (HEX unit) ............................................................... 98
(12)-3 Connection with PWFY-P100VM-E-BU (Booster unit) ................................................................. 98
(13)Correction by water flow rate
(For PWFY-P100/200VM-E-AU (HEX unit) and PWFY-P100VM-E-BU (Booster unit) ........................... 98
(13)-1 Connection with PWFY-P100VM-E-AU (HEX unit) ..................................................................... 98
(13)-2 Connection with PWFY-P200VM-E-AU (HEX unit) ...................................................................... 99
(13)-3 Connection with PWFY-P100VM-E-BU (Booster unit) ................................................................. 99
(14)Water pressure drop correction by water volume ............................................................................... 100
(14)-1 Heat source unit correction
(Connection with Standard CITY MULTI indoor units, PWFY-P100/200VM-E-AU,
PWFY-P100VM-E-BU) ............................................................................................................... 100
(14)-2 Booster unit correction (Connection with PWFY-P100VM-E-BU) .............................................. 100
(14)-3 HEX unit correction (Connection with PWFY-P100/200VM-E-AU) ............................................ 100
(14)-4 Water pressure drop of strainer only
(accessory for PWFY-P100VM-E-BU and PWFY-P100/200VM-E-AU) ..................................... 101
(15)Operation temperature range .............................................................................................................. 102
(15)-1 Connection with standard CITY MULTI indoor units .................................................................. 102
(15)-2 Connection with PWFY-P100VM-E-BU (Booster unit) ............................................................... 102
(15)-3 Connection with PWFY-P100/200VM-E-AU (HEX unit) ............................................................. 103
(16)Piping design ....................................................................................................................................... 104
(16)-1 R410A Piping material ................................................................................................................ 104
(16)-2 PQRY-P200-300YHM Piping
IF 16 ports or less are in use, i.e., if only one BC controller is in use with no sub BC controller
(Connection with standard CITY MULTI indoor units, PWFY-P100VM-E-BU,
PWFY-P100/200VM-E-AU) ........................................................................................................ 105
(16)-3 PQRY-P200-300YHM Piping
IF more than 16 ports are in use, or if there is more than one BC controller in use for
one Heat source unit
(Connection with standard CITY MULTI indoor units, PWFY-P100VM-E-BU,
PWFY-P100/200VM-E-AU) ........................................................................................................ 106
(16)-4 PQRY-P400YHM Piping
IF more than 16 ports are in use, or if there is more than one BC controller in use for
two heat source units
(Connection with standard CITY MULTI indoor units, PWFY-P100VM-E-BU,
PWFY-P100/200VM-E-AU) ........................................................................................................ 107
(16)-5 Total piping length restrictions .................................................................................................... 108
(16)-6 Refrigerant charging calculation ................................................................................................. 109

- 1 -
I Brine information
1.Brine freezing temperature
Brine concentration is decided by the freezing temperature. First, it is necessary to decide the freezing temperature and find
out brine concentration which will correspond to the freezing temperature.
0 10 20 30 40 50 60 70 80 90 100
10
0
-10
-20
-30
-40
-50
Brine concentration [wt%]
Freezing Temperature [deg°C]
Propylene Glycol
Ethylene Glycol
Propylene Glycol
Ethylene Glycol
Note;
The graph was referred from chemical company data.
But Freezing Temperature condition will be slightly different based on each company.
Please confirm detail data to the chemical company directly.
It is recommended to set the brine concentration to a percentage that will keep the freezing
temperature at -15deg°C or less.

- 2 -
2.Capacity correction by brine concentration (For heat source unit)
Depending on the freezing temperature and brine concentration, the ratio of unit capacity will change.
As shown in the line diagram, higher the brine concentration, the lower the ratio of capacity becomes.
Brine concentration [wt%]
Propylene Glycol
Ethylene Glycol
Propylene Glycol
Ethylene Glycol
Ratio of cooling capacity
1
0.95
0.9
0.85
0% 20% 40% 60% 80% 100%
Brine concentration [wt%]
Propylene Glycol
Ethylene Glycol
Propylene Glycol
Ethylene Glycol
Ratio of cooling input
1.30
1.25
1.20
1.15
1.10
1.05
1.00
0% 20% 40% 60% 80% 100%
Brine concentration [wt%]
Propylene Glycol
Ethylene Glycol
Propylene Glycol
Ethylene Glycol
Ratio of heating capacity
1.00
0.95
0.90
0.85
0.80
0.75
0.70
0% 20% 40% 60% 80% 100%
Brine concentration [wt%]
Propylene Glycol
Ethylene Glycol
Propylene Glycol
Ethylene Glycol
Ratio of heating input
1
0.95
0.9
0.85
0.8
0% 20% 40% 60% 80% 100%
PQHY
PQRY
IU IU
Cooling
Heating

- 3 -
3.Pressure drop correction by brine concentration (For heat source unit)
Also, water pump is selected by the ratio of pressure drop of depending on the brine concentration.
Cooling
Heating
Brine concentration [wt%]
Inlet-water temp. [°C]
Ratio of pressure drop
8.0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
-5°C
0°C
5°C
10°C
0% 20% 40% 60% 80% 100%
Brine concentration [wt%]
Inlet-water temp. [°C]
Ratio of pressure drop
8.0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
-5°C
0°C
5°C
10°C
0% 20% 40% 60% 80% 100%
Brine concentration [wt%]
Inlet-water temp. [°C]
Ethylene Glycol (heating)Ethylene Glycol (heating)
Ratio of pressure drop
26.0
21.0
16.0
11.0
6.0
1.0
-5°C
0°C
5°C
10°C
0% 20% 40% 60% 80% 100%
Brine concentration [wt%]
* Please supply strainer on site.
Inlet-water temp. [°C]
Ethylene Glycol (cooling)Ethylene Glycol (cooling)
Propylene Glycol (cooling)Propylene Glycol (cooling)
Propylene Glycol (heating)Propylene Glycol (heating)
Ratio of pressure drop
26.0
21.0
16.0
11.0
6.0
1.0
-5°C
0°C
5°C
10°C
0% 20% 40% 60% 80% 100%

- 4 -
II Heat source unit information
1.General lineup of water-cooled heat source unit
WY (Heat Pump) Series (8HP-36HP)
PQHY-P YHM-A
PQHY-P YSHM-A
WR2 (Heat Recovery) Series (8HP-24HP)
PQRY-P YHM-A
PQRY-P YSHM-A
Model 8HP 10HP 12HP 16HP
Model Name PQHY-P200YHM-A PQHY-P250YHM-A PQHY-P300YHM-A PQHY-P400YSHM-A
Model 18HP 20HP 22HP 24HP
Model Name PQHY-P450YSHM-A PQHY-P500YSHM-A PQHY-P550YSHM-A PQHY-P600YSHM-A
Model 26HP 28HP 30HP 32HP
Model Name PQHY-P650YSHM-A PQHY-P700YSHM-A PQHY-P750YSHM-A PQHY-P800YSHM-A
Model 34HP 36HP
Model Name PQHY-P850YSHM-A PQHY-P900YSHM-A
Model 8HP 10HP 12HP 16HP
Model Name PQRY-P200YHM-A PQHRY-P250YHM-A PQRY-P300YHM-A PQRY-P400YSHM-A
Model 18HP 20HP 22HP 24HP
Model Name PQRY-P450YSHM-A PQRY-P500YSHM-A PQRY-P550YSHM-A PQRY-P600YSHM-A

- 5 -
2.PQHY-P-Y(S)HM-A
(1) Specification
(1)-1 Heat source units specification for standard combination
(Standard CITY MULTI indoor units, PWFY-P100/200VM-E-AU)
*1
*2
Optional parts
Refrigerant
A
Current input
kW
A
kW
60.6POC kW / kW
6.9-6.6-6.3
kW
kcal / h
*2 BTU / h
Power input
kW / kW
W.B.
5.71
-5.0~45.0°C(23~113°F)
Sound pressure level (measured in anechoic room)
dB <A>
25.0
15.0~24.0°C(59~75°F)
=kW x 860
=kW x 3,412
=m
3
/min x 35.31
=kg / 0.4536
kcal
BTU/h
cfm
lb
cooling Circulating water
Heating capacity
Cooling capacity
47
15.0~27.0°C(59~81°F)
50~130 % of heat source unit capacity
P15~P250 / 1~17
-5.0~45.0°C(23~113°F)
85,300
4.12
1.0
KB94T222
5.0
195(430)
External dimension HxWxD
Motor output
kW
Lubricant
Case heater
kW
9.52(3/8) Brazed
19.05(3/4) Brazed
Inverter scroll hermetic compressor
4.5 ~ 7.2
4.6
Indoor LEV and BC controller
0.035(240 V)
High pressure sensor, High pressure switch at 4.15MPa (601 psi)Protection
noitcetorptnerruc-revO,noitcetorptaeh-revO).PMOC(tiucricretrevnIseci
ved
Unit converter
KE94C317
Refrigerant conn. pipe
Header: CMY-Y104/108/1010-G
*The specification data is
subject to rounding variation.
Wiring
Notes:
Standard attachment Document
Operating volume range m
3
/ h
Inverter
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
17
Joint: CMY-Y102S-G2
Remarks
●Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be refer
●Turn DipSW 3-9 ON before power ON.
red to the Installation Manual.
●Due to continuing improvement, above specifications may be subject to change without notice.
●The ambient temperature of the heat source unit needs to be kept below 40 °C D.B.
●The ambient relative humidity of the heat source unit needs to be kept below 80%.
●The heat source unit should not be installed at outdoor.
●Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
●Be sure to provide interlocking for the unit operation and water circuit.
●Add brine to circulating water when a unit is operating at water temperature below 10°C.
Drawing External
Accessory
Water flow rate m
3
/ h
L/min
Pressure drop kPa
mm
Compressor
in.
MPa
kg(lbs)
High pressure protection
Net weight
HIC circuit (HIC: Heat Inter-Changer)
Water volume in plate
Water pressure Max.
Compressor
water
Circulating
cfm
96
3.4
MEL32
1,160(1,100 without legs) x 880 x 550
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
Installation Manual
Power source
kW
h/lack)lanimoN(*1
6.6-6.2-6.0
PQHY-P200YHM-A(For Ground source)
3-phase 4-wire 380-400-415V 50/60Hz
19,300
22.4
3.92
76,400*1 BTU / h
Indoor unit
Temp. range of
Starting method
Type x Quantity
Manufacture
Power input
).ni(mmtnaregirfeR
mm(in.)
Liquid pipe
Gas pipe
Current input
(Nominal)
D.B.
*2
COP
°C
Indoor
Temp. range of Indoor
Model
External finish
Total capacity
piping diameter
Circulating water °C
connectable
Model / Quantity
heating
21,500
5.76
Type x original charge
Control
l
Acrylic painted steel plate
Over-heat protection
R410A x 5.0kg (12lbs)
Heat exchanger plate type
-
1.<Standard CITY MULTI indoor unit>
Nominal cooling conditions(subject to JIS B8615-1)
Indoor:27°CDB/19°CWB(81°FDB/66°FWB)
Water temperature:30°C(86°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
2.<PWFY-P100/200VM-E-AU>
Nominal cooling conditions
Circulating water Temp. : 30°C (86°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 23°C
Water flow rate : 1.93m
3
/h (P100) / 3.86m
3
/h (P200)
Brine concentration 0%
Nominal heating conditions(subject to JIS B8615-1)
Indoor:20°CDB(68°FDB)
Water temperature:20°C(68°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
Nominal heating conditions
Circulating water Temp. : 20°C (68°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 30°C
Water flow rate : 2.15m
3
/h (P100) / 4.30m
3
/h (P200)
Brine concentration 0%

- 6 -
*1
*2
-
plate typeHeat exchanger
Over-heat protection
Acrylic painted steel plate
l
Type x original charge
Control
5.76
27,100
Circulating water
°C
connectable
Model / Quantity
heating
Model
External finish
Total capacity
piping diameter
D.B.
*2
COP
°C
Indoor
Temp. range of Indoor
Current input
(Nominal)
mm(in.)
mm(in.)
Liquid pipe
Gas pipe
Power input
Refrigerant
Starting method
Type x Quantity
Manufacture
BTU / h
Indoor unit
Temp. range of
*1
28.0
5.45
95,500
9.2-8.7-8.4
PQHY-P250YHM-A(For Ground source)
3-phase 4-wire 380-400-415V 50/60Hz
24,100h/lack)lanimoN(*1
Power source
kW
R410A x 5.0kg (12lbs)
Installation Manual
MEL32
1,160(1,100 without legs) x 880 x 550
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
cfm
96
3.4
Compressor
water
Net weight
HIC circuit (HIC: Heat Inter-Changer)
Water volume in plate
Water pressure Max.
High pressure protection
MPa
kg(lbs)
mm
Compressor
in.
L/min
Pressure drop kPa
Water flow rate m
3
/ h
Circulating
Accessory
Drawing External
Joint: CMY-Y102S-G2, CMY-Y102L-G2
17
Inverter
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Operating volume range
m
3
/ h
Wiring
Standard attachment
Document
Refrigerant conn. pipe
Header: CMY-Y104/108/1010-G
KE94C317
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
Protection
noitcetorptnerruc-revO,noitcetorptaeh-revO).PMOC(tiucricretrevnIsecived
Indoor LEV and BC controller
0.035(240 V)
9.52(3/8) Brazed (12.7(1/2) Brazed,total length >= 90m)
22.2(7/8) Brazed
kW
Inverter scroll hermetic compressor
4.5 ~ 7.2
6.3
External dimension HxWxD
Motor output
kW
Lubricant
Case heater
5.0
195(430)
1.0
KB94T222
107,500
5.80
49
15.0~27.0°C(59~81°F)
50~130 % of heat source unit capacity
P15~P250 / 1~21
-5.0~45.0°C(23~113°F)
Cooling capacity
cooling
Circulating water
Heating capacity
Sound pressure level (measured in anechoic room)
dB <A>
31.5
15.0~24.0°C(59~75°F)W.B.
5.13
-5.0~45.0°C(23~113°F)
kW / kW
kcal / h
*2 BTU / h
Power input
kW
9.7-9.3-8.9
34.5POC kW / kW
kW
Current input
kW
A
A
Optional parts
Refrigerant
Remarks
●Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be refer
●Turn DipSW 3-9 ON before power ON.
red to the Installation Manual.
●Due to continuing improvement, above specifications may be subject to change without notice.
●The ambient temperature of the heat source unit needs to be kept below 40 °C D.B.
●The ambient relative humidity of the heat source unit needs to be kept below 80%.
●The heat source unit should not be installed at outdoor.
●Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
●Be sure to provide interlocking for the unit operation and water circuit.
●Add brine to circulating water when a unit is operating at water temperature below 10°C.
=kW x 860
=kW x 3,412
=m
3
/min x 35.31
=kg / 0.4536
kcal
BTU/h
cfm
lb
Unit converter
*The specification data is
subject to rounding variation.
Notes:
1.<Standard CITY MULTI indoor unit>
Nominal cooling conditions(subject to JIS B8615-1)
Indoor:27°CDB/19°CWB(81°FDB/66°FWB)
Water temperature:30°C(86°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
2.<PWFY-P100/200VM-E-AU>
Nominal cooling conditions
Circulating water Temp. : 30°C (86°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 23°C
Water flow rate : 1.93m3/h (P100) / 3.86m3/h (P200)
Brine concentration 0%
Nominal heating conditions(subject to JIS B8615-1)
Indoor:20°CDB(68°FDB)
Water temperature:20°C(68°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
Nominal heating conditions
Circulating water Temp. : 20°C (68°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 30°C
Water flow rate : 2.15m3/h (P100) / 4.30m3/h (P200)
Brine concentration 0%

- 7 -
*1
*2
-
plate type
Heat exchanger
Over-heat protection
Acrylic painted steel plate
l
Type x original charge
Control
5.76
32,300
Circulating water
°C
connectable
Model / Quantity
heating
Model
External finish
Total capacity
piping diameter
D.B.
*2
COP
°C
Indoor
Temp. range of Indoor
Current input
(Nominal)
mm(in.)
mm(in.)
Liquid pipe
Gas pipe
Power input
Refrigerant
Starting method
Type x Quantity
Manufacture
BTU / h
Indoor unit
Temp. range of
*1
33.5
7.36
114,300
12.4-11.8-11.3
PQHY-P300YHM-A(For Ground source)
3-phase 4-wire 380-400-415V 50/60Hz
28,800h/lack)lanimoN(*1
Power source
kW
R410A x 5.0kg (12lbs)
Installation Manual
MEL32
1,160(1,100 without legs) x 880 x 550
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
cfm
96
3.4
Compressor
water
Net weight
HIC circuit (HIC: Heat Inter-Changer)
Water volume in plate
Water pressure Max.
High pressure protection
MPa
kg(lbs)
mm
Compressor
in.
L/min
Pressure drop kPa
Water flow rate m
3
/ h
Circulating
Accessory
Drawing External
Joint: CMY-Y102S-G2,CMY-Y102L-G2
17
Inverter
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Operating volume range
m
3
/ h
Wiring
Standard attachment
Document
Refrigerant conn. pipe
Header: CMY-Y104/108/1010-G
KE94C317
High pressure sensor, High pressure switch at 4.15MPa (601 psi)Protection
noitcetorptnerruc-revO,noitcetorptaeh-revO).PMOC(tiucricretrevnIsecived
Indoor LEV and BC controller
0.035(240 V)
9.52(3/8) Brazed (12.7(1/2) Brazed,total length >= 40m)
22.2(7/8) Brazed
kW
Inverter scroll hermetic compressor
4.5 ~ 7.2
7.4
External dimension HxWxD
Motor output
kW
Lubricant
Case heater
5.0
195(430)
1.0
KB94T222
128,000
8.15
50
15.0~27.0°C(59~81°F)
50~130 % of heat source unit capacity
P15~P250 / 1~26
-5.0~45.0°C(23~113°F)
Cooling capacity
cooling
Circulating water
Heating capacity
Sound pressure level (measured in anechoic room)
dB <A>
37.5
15.0~24.0°C(59~75°F)W.B.
4.55
-5.0~45.0°C(23~113°F)
kW / kW
kcal / h
*2 BTU / h
Power input
kW
13.7-13.0-12.5
06.4POC kW / kW
kW
Current input
kW
A
A
Optional parts
Refrigerant
=kW x 860
=kW x 3,412
=m
3
/min x 35.31
=kg / 0.4536
kcal
BTU/h
cfm
lb
Unit converter
*The specification data is
subject to rounding variation.
Notes:
Remarks
●Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be refer
●Turn DipSW 3-9 ON before power ON.
red to the Installation Manual.
●Due to continuing improvement, above specifications may be subject to change without notice.
●The ambient temperature of the heat source unit needs to be kept below 40 °C D.B.
●The ambient relative humidity of the heat source unit needs to be kept below 80%.
●The heat source unit should not be installed at outdoor.
●Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
●Be sure to provide interlocking for the unit operation and water circuit.
●Add brine to circulating water when a unit is operating at water temperature below 10°C.
1.<Standard CITY MULTI indoor unit>
Nominal cooling conditions(subject to JIS B8615-1)
Indoor:27°CDB/19°CWB(81°FDB/66°FWB)
Water temperature:30°C(86°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
2.<PWFY-P100/200VM-E-AU>
Nominal cooling conditions
Circulating water Temp. : 30°C (86°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 23°C
Water flow rate : 1.93m
3
/h (P100) / 3.86m
3
/h (P200)
Brine concentration 0%
Nominal heating conditions(subject to JIS B8615-1)
Indoor:20°CDB(68°FDB)
Water temperature:20°C(68°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
Nominal heating conditions
Circulating water Temp. : 20°C (68°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 30°C
Water flow rate : 2.15m
3
/h (P100) / 4.30m
3
/h (P200)
Brine concentration 0%

- 8 -
*1
*2
Heat Source Twinning kit: CMY-Y100VBK2
9.52(3/8) Brazed
-
1.0
5.0
1.0
Over-heat protection, Over-current protection Over-heat protection, Over-current protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
Over-heat protection
Acrylic painted steel plate
23LEM23LEM
4.6
)V042(530.0)V042(530.0WkretaehesaC
6.4WktuptuorotoM
Inverter scroll hermetic compressor
Inverter
AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter
Inverter scroll hermetic compressor
in.
Over-heat protection
Control
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
195(430)
5.76 + 5.76
43,000
Circulating water
°C
Set Model
Model
connectable
Model / Quantity
heating
Model
Total capacity
piping diameter
D.B.
*2
COP
°C
Indoor
Temp. range of
Current input
(Nominal)
mm(in.)
mm(in.)
Liquid pipe
Gas pipe
Power input
Refrigerant
BTU / h
Indoor unit
Temp. range of
*1
45.0
8.25
153,500
13.9-13.2-12.7
PQHY-P400YSHM-A (For Ground source)
3-phase 4-wire 380-400-415V 50/60Hz
38,700h/lack)lanimoN(*1
Power source
kW
Installation Manual
Acrylic painted steel plate
1,160(1,100 without legs) x 880 x 550
cfm
96 + 96
3.4 + 3.4
l
Water volume in plate
wate r
HIC circuit (HIC: Heat Inter-Changer)
Heat exchanger
Water pressure Max.
Protection
mm
External dimension HxWxD
Type x original charge
)sbl(gkthgiewteN
MPa
High pressure protection
Inverter circuit (COMP.)
Manufacture
Starting method
L/min
Water flow rate m
3
/ h
Circulating
Compressor
Accessory
Drawing
distributor
KE94C317
Joint: CMY-Y102S-G2, CMY-Y102L-G2, CMY-Y202-G2
Remarks
●Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be refer
●Turn DipSW 3-9 ON before power ON.
red to the Installation Manual.
●Due to continuing improvement, above specifications may be subject to change without notice.
●The ambient temperature of the heat source unit needs to be kept below 40 °C D.B.
●The ambient relative humidity of the heat source unit needs to be kept below 80%.
●The heat source unit should not be installed at outdoor.
●Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
●Be sure to provide interlocking for the unit operation and water circuit.
●Add brine to circulating water when a unit is operating at water temperature below 10°C.
●Twinning kit is required.
KE94C317
kPaPressure drop
Operating volume range
m
3
/ h
Notes:
Standard attachment Document
Wiring
External
*The specification data is
subject to rounding variation.
Refrigerant conn. pipe
Header: CMY-Y104/108/1010-G
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
Unit converter
R410A x 5.0kg (12lbs)
Indoor LEV and BC controller
1,160(1,100 without legs) x 880 x 550
PQHY-P200YHM-A(For Ground source)
12.7(1/2) Brazed
28.58(1-1/8) Brazed
epytetalpepytetalp
5.0
4.5 + 4.5 ~ 7.2 + 7.2
Lubricant
Type x Quantity
External finish
-
R410A x 5.0kg (12lbs)
195(430)
KB94T223
9.52(3/8) Brazed
170,600
PQHY-P200YHM-A(For Ground source)
8.65
50
15.0~27.0°C(59~81°F)
50~130 % of heat source unit capacity
P15~P250 / 1~34
-5.0~45.0°C(23~113°F)
7171
Gas pipe mm(in.) dezarB)4/3(50.91dezarB)4/3(50.91
Cooling capacity
devices
Compressor
cooling
Circulating water
Indoor
Heating capacity
=kW x 860
=kW x 3,412
=m
3
/min x 35.31
=kg / 0.4536
kcal
BTU/h
cfm
lb
Pipe between unit and
Liquid pipe mm(in.)
Sound pressure level (measured in anechoic room)
dB <A>
50.0
15.0~24.0°C(59~75°F)W.B.
5.45
-5.0~45.0°C(23~113°F)
kW / kW
kcal / h
*2 BTU / h
Power input
kW
14.6-13.8-13.3
87.5POC kW / kW
kW
Current input
kW
A
A
Optional parts
Refri gerant
1.<Standard CITY MULTI indoor unit>
Nominal cooling conditions(subject to JIS B8615-1)
Indoor:27°CDB/19°CWB(81°FDB/66°FWB)
Water temperature:30°C(86°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
2.<PWFY-P100/200VM-E-AU>
Nominal cooling conditions
Circulating water Temp. : 30°C (86°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 23°C
Water flow rate : 1.93m
3
/h (P100) / 3.86m
3
/h (P200)
Brine concentration 0%
Nominal heating conditions(subject to JIS B8615-1)
Indoor:20°CDB(68°FDB)
Water temperature:20°C(68°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
Nominal heating conditions
Circulating water Temp. : 20°C (68°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 30°C
Water flow rate : 2.15m
3
/h (P100) / 4.30m
3
/h (P200)
Brine concentration 0%

- 9 -
*1
*2
WkretaehesaC
WktuptuorotoM
in.
Control
Circulating water
°C
Set Model
Model
connectable
Model / Quantity
heating
Model
Total capacity
piping diameter
D.B.
*2
COP
°C
Indoor
Temp. range of
Current input
(Nominal)
mm(in.)
mm(in.)
Liquid pipe
Gas pipe
Power input
Refrigerant
BTU / h
Indoor unit
Temp. range of
*1
h/lack)lanimoN(*1
Power source
kW
cfm
l
Water volume in plate
wate r
HIC circuit (HIC: Heat Inter-Changer)
Heat exchanger
Water pressure Max.
Protection
mm
External dimension HxWxD
Type x original charge
)sbl(gkthgiewteN
MPa
High pressure protection
Inverter circuit (COMP.)
Manufacture
Starting method
L/min
Water flow rate m
3
/ h
Circulating
Compressor
Accessory
Drawing
distributor
Remarks
●Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be refer
●Turn DipSW 3-9 ON before power ON.
red to the Installation Manual.
●Due to continuing improvement, above specifications may be subject to change without notice.
●The ambient temperature of the heat source unit needs to be kept below 40 °C D.B.
●The ambient relative humidity of the heat source unit needs to be kept below 80%.
●The heat source unit should not be installed at outdoor.
●Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
●Be sure to provide interlocking for the unit operation and water circuit.
●Add brine to circulating water when a unit is operating at water temperature below 10°C.
●Twinning kit is required.
kPaPressure drop
Operating volume range
m
3
/ h
Notes:
Standard attachment Document
Wiring
External
*The specification data is
subject to rounding variation.
Unit converter
Lubricant
Type x Quantity
External finish
Gas pipe mm(in.)
Cooling capacity
devices
Compressor
cooling
Circulating water
Indoor
Heating capacity
=kW x 860
=kW x 3,412
=m
3
/min x 35.31
=kg / 0.4536
kcal
BTU/h
cfm
lb
Pipe between unit and
Liquid pipe mm(in.)
Sound pressure level (measured in anechoic room)
dB <A>
W.B.
kW / kW
kcal / h
*2 BTU / h
Power input
kW
POC kW / kW
kW
Current input
kW
A
A
Optional parts
Refri gerant
1.<Standard CITY MULTI indoor unit>
Nominal cooling conditions(subject to JIS B8615-1)
Indoor:27°CDB/19°CWB(81°FDB/66°FWB)
Water temperature:30°C(86°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
2.<PWFY-P100/200VM-E-AU>
Nominal cooling conditions
Circulating water Temp. : 30°C (86°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 23°C
Water flow rate : 1.93m
3
/h (P100) / 3.86m
3
/h (P200)
Brine concentration 0%
Nominal heating conditions(subject to JIS B8615-1)
Indoor:20°CDB(68°FDB)
Water temperature:20°C(68°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
Nominal heating conditions
Circulating water Temp. : 20°C (68°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 30°C
Water flow rate : 2.15m
3
/h (P100) / 4.30m
3
/h (P200)
Brine concentration 0%
Heat Source Twinning kit: CMY-Y100VBK2
9.52(3/8) Brazed
--
1.0
5.0
1.0
Over-heat protection, Over-current protection Over-heat protection, Over-current protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
Over-heat protection
Acrylic painted steel plate
23LEM23LEM
4.6
)V042(530.0)V042(530.0
3.6
Inverter scroll hermetic compressor
Inverter
AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter
Inverter scroll hermetic compressor
Over-heat protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
195(430)
5.76 + 5.76
48,200
50.0
9.84
170,600
16.6-15.7-15.2
PQHY-P450YSHM-A(For Ground source)
3-phase 4-wire 380-400-415V 50/60Hz
43,000
Installation Manual
Acrylic painted steel plate
1,160(1,100 without legs) x 880 x 550
96 + 96
3.4 + 3.4
KE94C317
Joint: CMY-Y102S-G2, CMY-Y102L-G2, CMY-Y202-G2
KE94C317
Refrigerant conn. pipe
Header: CMY-Y104/108/1010-G
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
R410A x 5.0kg (12lbs)
Indoor LEV and BC controller
1,160(1,100 without legs) x 880 x 550
PQHY-P250YHM-A(For Ground source)
15.88(5/8) Brazed
28.58(1-1/8) Brazed
epytetalpepytetalp
5.0
4.5 + 4.5 ~ 7.2 + 7.2
R410A x 5.0kg (12lbs)
195(430)
KB94T223
9.52(3/8) Brazed
191,100
PQHY-P200YHM-A(For Ground source)
10.42
51
15.0~27.0°C(59~81°F)
50~130 % of heat source unit capacity
P15~P250 / 1~39
-5.0~45.0°C(23~113°F)
7171
dezarB)8/7(2.22dezarB)8/7(2.22
56.0
15.0~24.0°C(59~75°F)
5.08
-5.0~45.0°C(23~113°F)
17.5-16.7-16.1
73.5

- 10 -
*1
*2
WkretaehesaC
WktuptuorotoM
in.
Control
Circulating water
°C
Set Model
Model
connectable Model / Quantity
heating
Model
Total capacity
piping diameter
D.B.
*2
COP
°C
Indoor
Temp. range of
Current input
(Nominal)
mm(in.)
mm(in.)
Liquid pipe
Gas pipe
Power input
Refrigerant
BTU / h
Indoor unit
Temp. range of
*1
h/lack)lanimoN(*1
Power source
kW
cfm
l
Water volume in plate
wate r
HIC circuit (HIC: Heat Inter-Changer)
Heat exchanger
Water pressure Max.
Protection
mm
External dimension HxWxD
Type x original charge
)sbl(gkthgiewteN
MPa
High pressure protection
Inverter circuit (COMP.)
Manufacture
Starting method
L/min
Water flow rate m3/ h
Circulating
Compressor
Accessory
Drawing
distributor
Remarks
●Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be refer
●Turn DipSW 3-9 ON before power ON.
red to the Installation Manual.
●Due to continuing improvement, above specifications may be subject to change without notice.
●The ambient temperature of the heat source unit needs to be kept below 40 °C D.B.
●The ambient relative humidity of the heat source unit needs to be kept below 80%.
●The heat source unit should not be installed at outdoor.
●Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
●Be sure to provide interlocking for the unit operation and water circuit.
●Add brine to circulating water when a unit is operating at water temperature below 10°C.
●Twinning kit is required.
kPaPressure drop
Operating volume range m3/ h
Notes:
Standard attachment Document
Wiring
External
*The specification data is
subject to rounding variation.
Unit converter
Lubricant
Type x Quantity
External finish
Gas pipe mm(in.)
Cooling capacity
devices
Compressor
cooling
Circulating water
Indoor
Heating capacity
=kW x 860
=kW x 3,412
=m3/min x 35.31
=kg / 0.4536
kcal
BTU/h
cfm
lb
Pipe between unit and Liquid pipe mm(in.)
Sound pressure level (measured in anechoic room) dB <A>
W.B.
kW / kW
kcal / h
*2 BTU / h
Power input
kW
POC kW / kW
kW
Current input
kW
A
A
Optional parts
Refri gerant
1.<Standard CITY MULTI indoor unit>
Nominal cooling conditions(subject to JIS B8615-1)
Indoor:27°CDB/19°CWB(81°FDB/66°FWB)
Water temperature:30°C(86°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
2.<PWFY-P100/200VM-E-AU>
Nominal cooling conditions
Circulating water Temp. : 30°C (86°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 23°C
Water flow rate : 1.93m3/h (P100) / 3.86m3/h (P200)
Brine concentration 0%
Nominal heating conditions(subject to JIS B8615-1)
Indoor:20°CDB(68°FDB)
Water temperature:20°C(68°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
Nominal heating conditions
Circulating water Temp. : 20°C (68°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 30°C
Water flow rate : 2.15m3/h (P100) / 4.30m3/h (P200)
Brine concentration 0%
Heat Source Twinning kit: CMY-Y100VBK2
9.52(3/8) Brazed
-
1.0
5.0
1.0
Over-heat protection, Over-current protection Over-heat protection, Over-current protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
Over-heat protection
Acrylic painted steel plate
23LEM23LEM
6.3
)V042(530.0)V042(530.0
3.6
Inverter scroll hermetic compressor
Inverter
AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter
Inverter scroll hermetic compressor
Over-heat protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
195(430)
5.76 + 5.76
54,200
56.0
11.45
191,100
19.3-18.3-17.6
PQHY-P500YSHM-A(For Ground source)
3-phase 4-wire 380-400-415V 50/60Hz
48,200
Installation Manual
Acrylic painted steel plate
1,160(1,100 without legs) x 880 x 550
96 + 96
3.4 + 3.4
KE94C317
Joint: CMY-Y102S-G2, CMY-Y102L-G2, CMY-Y202-G2
KE94C317
Refrigerant conn. pipe
Header: CMY-Y104/108/1010-G
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
R410A x 5.0kg (12lbs)
Indoor LEV and BC controller
1,160(1,100 without legs) x 880 x 550
PQHY-P250YHM-A(For Ground source)
15.88(5/8) Brazed
28.58(1-1/8) Brazed
epytetalpepytetalp
5.0
4.5 + 4.5 ~ 7.2 + 7.2
-
R410A x 5.0kg (12lbs)
195(430)
KB94T223
9.52(3/8) Brazed
215,000
PQHY-P250YHM-A(For Ground source)
12.06
52
15.0~27.0°C(59~81°F)
50~130 % of heat source unit capacity
P15~P250 / 1~43
-5.0~45.0°C(23~113°F)
7171
dezarB)8/7(2.22dezarB)8/7(2.22
63.0
15.0~24.0°C(59~75°F)
4.89
-5.0~45.0°C(23~113°F)
20.3-19.3-18.6
22.5

- 11 -
*1
*2
WkretaehesaC
WktuptuorotoM
in.
Control
Circulating water
°C
Set Model
Model
connectable Model / Quantity
heating
Model
Total capacity
piping diameter
D.B.
*2
COP
°C
Indoor
Temp. range of
Current input
(Nominal)
mm(in.)
mm(in.)
Liquid pipe
Gas pipe
Power input
Refrigerant
BTU / h
Indoor unit
Temp. range of
*1
h/lack)lanimoN(*1
Power source
kW
cfm
l
Water volume in plate
wate r
HIC circuit (HIC: Heat Inter-Changer)
Heat exchanger
Water pressure Max.
Protection
mm
External dimension HxWxD
Type x original charge
)sbl(gkthgiewteN
MPa
High pressure protection
Inverter circuit (COMP.)
Manufacture
Starting method
L/min
Water flow rate m3/ h
Circulating
Compressor
Accessory
Drawing
distributor
Remarks
●Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be refer
●Turn DipSW 3-9 ON before power ON.
red to the Installation Manual.
●Due to continuing improvement, above specifications may be subject to change without notice.
●The ambient temperature of the heat source unit needs to be kept below 40 °C D.B.
●The ambient relative humidity of the heat source unit needs to be kept below 80%.
●The heat source unit should not be installed at outdoor.
●Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
●Be sure to provide interlocking for the unit operation and water circuit.
●Add brine to circulating water when a unit is operating at water temperature below 10°C.
●Twinning kit is required.
kPaPressure drop
Operating volume range m3/ h
Notes:
Standard attachment Document
Wiring
External
*The specification data is
subject to rounding variation.
Unit converter
Lubricant
Type x Quantity
External finish
Gas pipe mm(in.)
Cooling capacity
devices
Compressor
cooling
Circulating water
Indoor
Heating capacity
=kW x 860
=kW x 3,412
=m3/min x 35.31
=kg / 0.4536
kcal
BTU/h
cfm
lb
Pipe between unit and Liquid pipe mm(in.)
Sound pressure level (measured in anechoic room) dB <A>
W.B.
kW / kW
kcal / h
*2 BTU / h
Power input
kW
POC kW / kW
kW
Current input
kW
A
A
Optional parts
Refri gerant
1.<Standard CITY MULTI indoor unit>
Nominal cooling conditions(subject to JIS B8615-1)
Indoor:27°CDB/19°CWB(81°FDB/66°FWB)
Water temperature:30°C(86°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
2.<PWFY-P100/200VM-E-AU>
Nominal cooling conditions
Circulating water Temp. : 30°C (86°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 23°C
Water flow rate : 1.93m3/h (P100) / 3.86m3/h (P200)
Brine concentration 0%
Nominal heating conditions(subject to JIS B8615-1)
Indoor:20°CDB(68°FDB)
Water temperature:20°C(68°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
Nominal heating conditions
Circulating water Temp. : 20°C (68°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 30°C
Water flow rate : 2.15m3/h (P100) / 4.30m3/h (P200)
Brine concentration 0%
Heat Source Twinning kit: CMY-Y100VBK2
12.7(1/2) Brazed
-
1.0
5.0
1.0
Over-heat protection, Over-current protection Over-heat protection, Over-current protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
Over-heat protection
Acrylic painted steel plate
23LEM23LEM
6.3
)V042(530.0)V042(530.0
4.7
Inverter scroll hermetic compressor
Inverter
AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter
Inverter scroll hermetic compressor
Over-heat protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
195(430)
5.76 + 5.76
59,300
63.0
13.46
215,000
22.7-21.5-20.8
PQHY-P550YSHM-A(For Ground source)
3-phase 4-wire 380-400-415V 50/60Hz
54,200
Installation Manual
Acrylic painted steel plate
1,160(1,100 without legs) x 880 x 550
96 + 96
3.4 + 3.4
KE94C317
Joint: CMY-Y102S-G2, CMY-Y102L-G2, CMY-Y202-G2,CMY-Y302-G2
KE94C317
Refrigerant conn. pipe
Header: CMY-Y104/108/1010-G
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
R410A x 5.0kg (12lbs)
Indoor LEV and BC controller
1,160(1,100 without legs) x 880 x 550
PQHY-P300YHM-A(For Ground source)
15.88(5/8) Brazed
28.58(1-1/8) Brazed
epytetalpepytetalp
5.0
4.5 + 4.5 ~ 7.2 + 7.2
-
R410A x 5.0kg (12lbs)
195(430)
KB94T223
12.7(1/2) Brazed
235,400
PQHY-P250YHM-A(For Ground source)
14.65
52.5
15.0~27.0°C(59~81°F)
50~130 % of heat source unit capacity
P15~P250 / 2~47
-5.0~45.0°C(23~113°F)
7171
22.2(7/8) BrazeddezarB)8/7(2.22
69.0
15.0~24.0°C(59~75°F)
4.68
-5.0~45.0°C(23~113°F)
24.7-23.4-22.6
07.4

- 12 -
*1
*2
WkretaehesaC
WktuptuorotoM
in.
Control
Circulating water
°C
Set Model
Model
connectable
Model / Quantity
heating
Model
Total capacity
piping diameter
D.B.
*2
COP
°C
Indoor
Temp. range of
Current input
(Nominal)
mm(in.)
mm(in.)
Liquid pipe
Gas pipe
Power input
Refrigerant
BTU / h
Indoor unit
Temp. range of
*1
h/lack)lanimoN(*1
Power source
kW
cfm
l
Water volume in plate
wate r
HIC circuit (HIC: Heat Inter-Changer)
Heat exchanger
Water pressure Max.
Protection
mm
External dimension HxWxD
Type x original charge
)sbl(gkthgiewteN
MPa
High pressure protection
Inverter circuit (COMP.)
Manufacture
Starting method
L/min
Water flow rate m
3
/ h
Circulating
Compressor
Accessory
Drawing
distributor
Remarks
●Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be refer
●Turn DipSW 3-9 ON before power ON.
red to the Installation Manual.
●Due to continuing improvement, above specifications may be subject to change without notice.
●The ambient temperature of the heat source unit needs to be kept below 40 °C D.B.
●The ambient relative humidity of the heat source unit needs to be kept below 80%.
●The heat source unit should not be installed at outdoor.
●Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
●Be sure to provide interlocking for the unit operation and water circuit.
●Add brine to circulating water when a unit is operating at water temperature below 10°C.
●Twinning kit is required.
kPaPressure drop
Operating volume range
m
3
/ h
Notes:
Standard attachment Document
Wiring
External
*The specification data is
subject to rounding variation.
Unit converter
Lubricant
Type x Quantity
External finish
Gas pipe mm(in.)
Cooling capacity
devices
Compressor
cooling
Circulating water
Indoor
Heating capacity
=kW x 860
=kW x 3,412
=m
3
/min x 35.31
=kg / 0.4536
kcal
BTU/h
cfm
lb
Pipe between unit and
Liquid pipe mm(in.)
Sound pressure level (measured in anechoic room)
dB <A>
W.B.
kW / kW
kcal / h
*2 BTU / h
Power input
kW
POC kW / kW
kW
Current input
kW
A
A
Optional parts
Refri gerant
1.<Standard CITY MULTI indoor unit>
Nominal cooling conditions(subject to JIS B8615-1)
Indoor:27°CDB/19°CWB(81°FDB/66°FWB)
Water temperature:30°C(86°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
2.<PWFY-P100/200VM-E-AU>
Nominal cooling conditions
Circulating water Temp. : 30°C (86°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 23°C
Water flow rate : 1.93m
3
/h (P100) / 3.86m
3
/h (P200)
Brine concentration 0%
Nominal heating conditions(subject to JIS B8615-1)
Indoor:20°CDB(68°FDB)
Water temperature:20°C(68°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
Nominal heating conditions
Circulating water Temp. : 20°C (68°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 30°C
Water flow rate : 2.15m
3
/h (P100) / 4.30m
3
/h (P200)
Brine concentration 0%
Heat Source Twinning kit: CMY-Y100VBK2
12.7(1/2) Brazed
-
1.0
5.0
1.0
Over-heat protection, Over-current protection Over-heat protection, Over-current protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
Over-heat protection
Acrylic painted steel plate
23LEM
7.4
)V042(530.0
23LEM
)V042(530.0
4.7
Inverter scroll hermetic compressor
Inverter
AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter
Inverter scroll hermetic compressor
Over-heat protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
195(430)
5.76 + 5.76
65,800
69.0
15.48
235,400
26.1-24.8-23.9
PQHY-P600YSHM-A(For Ground source)
3-phase 4-wire 380-400-415V 50/60Hz
59,300
Installation Manual
Acrylic painted steel plate
1,160(1,100 without legs) x 880 x 550
96 + 96
3.4 + 3.4
KE94C317
Joint: CMY-Y102S-G2, CMY-Y102L-G2, CMY-Y202-G2,CMY-Y302-G2
KE94C317
Refrigerant conn. pipe
Header: CMY-Y104/108/1010-G
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
R410A x 5.0kg (12lbs)
Indoor LEV and BC controller
1,160(1,100 without legs) x 880 x 550
PQHY-P300YHM-A(For Ground source)
15.88(5/8) Brazed
28.58(1-1/8) Brazed
epytetalpepytetalp
5.0
4.5 + 4.5 ~ 7.2 + 7.2
-
R410A x 5.0kg (12lbs)
195(430)
KB94T223
12.7(1/2) Brazed
261,000
PQHY-P300YHM-A(For Ground source)
17.12
53
15.0~27.0°C(59~81°F)
50~130 % of heat source unit capacity
P15~P250 / 2~50
-5.0~45.0°C(23~113°F)
7171
22.2(7/8) Brazed22.2(7/8) Brazed
76.5
15.0~24.0°C(59~75°F)
4.45
-5.0~45.0°C(23~113°F)
28.9-27.4-26.4
64.4

- 13 -
*1
*2
WkretaehesaC
WktuptuorotoM
in.
Control
Circulating water
°C
Set Model
Model
connectable
Model / Quantity
heating
Model
Total capacity
piping diameter
D.B.
*2
COP
°C
Indoor
Temp. range of
Current input
(Nominal)
mm(in.)
mm(in.)
Liquid pipe
Gas pipe
Power input
Refrigerant
BTU / h
Indoor unit
Temp. range of
*1
h/lack)lanimoN(*1
Power source
kW
cfm
l
Water volume in plate
wate r
HIC circuit (HIC: Heat Inter-Changer)
Heat exchanger
Water pressure Max.
Protection
mm
External dimension HxWxD
Type x original charge
)sbl(gkthgiewteN
MPa
High pressure protection
Inverter circuit (COMP.)
Manufacture
Starting method
L/min
Water flow rate m
3
/ h
Circulating
Compressor
Accessory
Drawing
distributor
Remarks
●Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be refer
●Turn DipSW 3-9 ON before power ON.
red to the Installation Manual.
●Due to continuing improvement, above specifications may be subject to change without notice.
●The ambient temperature of the heat source unit needs to be kept below 40 °C D.B.
●The ambient relative humidity of the heat source unit needs to be kept below 80%.
●The heat source unit should not be installed at outdoor.
●Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
●Be sure to provide interlocking for the unit operation and water circuit.
●Add brine to circulating water when a unit is operating at water temperature below 10°C.
●Twinning kit is required.
kPaPressure drop
Operating volume range
m
3
/ h
Notes:
Standard attachment Document
Wiring
External
*The specification data is
subject to rounding variation.
Unit converter
Lubricant
Type x Quantity
External finish
Gas pipe mm(in.)
Cooling capacity
devices
Compressor
cooling
Circulating water
Indoor
Heating capacity
=kW x 860
=kW x 3,412
=m
3
/min x 35.31
=kg / 0.4536
kcal
BTU/h
cfm
lb
Pipe between unit and
Liquid pipe mm(in.)
Sound pressure level (measured in anechoic room)
dB <A>
W.B.
kW / kW
kcal / h
*2 BTU / h
Power input
kW
POC kW / kW
kW
Current input
kW
A
A
Optional parts
Refri gerant
1.<Standard CITY MULTI indoor unit>
Nominal cooling conditions(subject to JIS B8615-1)
Indoor:27°CDB/19°CWB(81°FDB/66°FWB)
Water temperature:30°C(86°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
2.<PWFY-P100/200VM-E-AU>
Nominal cooling conditions
Circulating water Temp. : 30°C (86°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 23°C
Water flow rate : 1.93m
3
/h (P100) / 3.86m
3
/h (P200)
Brine concentration 0%
Nominal heating conditions(subject to JIS B8615-1)
Indoor:20°CDB(68°FDB)
Water temperature:20°C(68°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
Nominal heating conditions
Circulating water Temp. : 20°C (68°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 30°C
Water flow rate : 2.15m
3
/h (P100) / 4.30m
3
/h (P200)
Brine concentration 0%
25.5
24.8-23.6-22.7
5.22
-5.0~45.0°C(23~113°F)
81.5
15.0~24.0°C(59~75°F)
53
15.0~27.0°C(59~81°F)
50~130 % of heat source unit capacity
P15~P250 / 2~50
-5.0~45.0°C(23~113°F)
12.7(1/2) Brazed
278,100
14.74
195(430)
KB94T659
Over-heat protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
Over-heat protection, Over-current protectionOver-heat protection, Over-current protectionOver-heat protection, Over-current protection
R410A x 5.0kg (12lbs) R410A x 5.0kg (12lbs)
Over-heat protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
5.0
19.05(3/4) Brazed
34.93(1-3/8) Brazed
4.5 + 4.5 + 4.5 ~ 7.2 + 7.2 + 7.2
LEV and HIC circuit
epytetalpepytetalp
5.0
1.0
17
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
Refrigerant conn. pipe
Header: CMY-Y104/108/1010-G
Joint: CMY-Y102S-G2,CMY-Y102L-G2,CMY-Y202-G2,CMY-Y302-G2
96 + 96 + 96
3.4 + 3.4 + 3.4
Installation Manual
713C49EK713C49EK713C49EK
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
1,160(1,100 without legs) x 880 x 550 1,160(1,100 without legs) x 880 x 550 1,160(1,100 without legs) x 880 x 550
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
23.5-22.3-21.5
PQHY-P650YSHM-A(For Ground source)
3-phase 4-wire 380-400-415V 50/60Hz
62,800
73.0
13.96
249,100
70,100
PQHY-P200YHM-A(For Ground source)
PQHY-P200YHM-A(For Ground source)PQHY-P250YHM-A(For Ground source)
5.76 + 5.76 + 5.76
7171
Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter scroll hermetic compressor Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter
6.3
retrevnIretrevnI
6.46.4
0.035(240 V)
MEL32
0.035(240 V) 0.035(240 V)
23LEM23LEM
Acrylic painted steel plateAcrylic painted steel plate Acrylic painted steel plate
R410A x 5.0kg (12lbs)
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
Over-heat protection
195(430)
epytetalp
Copper pipe,tube-in-tube structure
1.0
5.0
1.0
Copper pipe,tube-in-tube structure
12.7(1/2) Brazed
22.2(7/8) Brazed
Heat Source Twinning kit: CMY-Y300VBK2
12.7(1/2) Brazed
19.05(3/4) Brazed 19.05(3/4) Brazed
Copper pipe,tube-in-tube structure
195(430)

- 14 -
*1
*2
WkretaehesaC
WktuptuorotoM
in.
Control
Circulating water
°C
Set Model
Model
connectable
Model / Quantity
heating
Model
Total capacity
piping diameter
D.B.
*2
COP
°C
Indoor
Temp. range of
Current input
(Nominal)
mm(in.)
mm(in.)
Liquid pipe
Gas pipe
Power input
Refrigerant
BTU / h
Indoor unit
Temp. range of
*1
h/lack)lanimoN(*1
Power source
kW
cfm
l
Water volume in plate
wate r
HIC circuit (HIC: Heat Inter-Changer)
Heat exchanger
Water pressure Max.
Protection
mm
External dimension HxWxD
Type x original charge
)sbl(gkthgiewteN
MPa
High pressure protection
Inverter circuit (COMP.)
Manufacture
Starting method
L/min
Water flow rate m
3
/ h
Circulating
Compressor
Accessory
Drawing
distributor
Remarks
●Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be refer
●Turn DipSW 3-9 ON before power ON.
red to the Installation Manual.
●Due to continuing improvement, above specifications may be subject to change without notice.
●The ambient temperature of the heat source unit needs to be kept below 40 °C D.B.
●The ambient relative humidity of the heat source unit needs to be kept below 80%.
●The heat source unit should not be installed at outdoor.
●Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
●Be sure to provide interlocking for the unit operation and water circuit.
●Add brine to circulating water when a unit is operating at water temperature below 10°C.
●Twinning kit is required.
kPaPressure drop
Operating volume range
m
3
/ h
Notes:
Standard attachment Document
Wiring
External
*The specification data is
subject to rounding variation.
Unit converter
Lubricant
Type x Quantity
External finish
Gas pipe mm(in.)
Cooling capacity
devices
Compressor
cooling
Circulating water
Indoor
Heating capacity
=kW x 860
=kW x 3,412
=m
3
/min x 35.31
=kg / 0.4536
kcal
BTU/h
cfm
lb
Pipe between unit and
Liquid pipe mm(in.)
Sound pressure level (measured in anechoic room)
dB <A>
W.B.
kW / kW
kcal / h
*2 BTU / h
Power input
kW
POC kW / kW
kW
Current input
kW
A
A
Optional parts
Refri gerant
1.<Standard CITY MULTI indoor unit>
Nominal cooling conditions(subject to JIS B8615-1)
Indoor:27°CDB/19°CWB(81°FDB/66°FWB)
Water temperature:30°C(86°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
2.<PWFY-P100/200VM-E-AU>
Nominal cooling conditions
Circulating water Temp. : 30°C (86°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 23°C
Water flow rate : 1.93m
3
/h (P100) / 3.86m
3
/h (P200)
Brine concentration 0%
Nominal heating conditions(subject to JIS B8615-1)
Indoor:20°CDB(68°FDB)
Water temperature:20°C(68°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
Nominal heating conditions
Circulating water Temp. : 20°C (68°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 30°C
Water flow rate : 2.15m
3
/h (P100) / 4.30m
3
/h (P200)
Brine concentration 0%
33.5
27.8-26.4-25.5
5.13
-5.0~45.0°C(23~113°F)
88.0
15.0~24.0°C(59~75°F)
53.5
15.0~27.0°C(59~81°F)
50~130 % of heat source unit capacity
P15~P250 / 2~50
-5.0~45.0°C(23~113°F)
12.7(1/2) Brazed
300,300
16.51
195(430)
KB94T659
Over-heat protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
Over-heat protection, Over-current protectionOver-heat protection, Over-current protectionOver-heat protection, Over-current protection
R410A x 5.0kg (12lbs) R410A x 5.0kg (12lbs)
Over-heat protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
5.0
19.05(3/4) Brazed
34.93(1-3/8) Brazed
4.5 + 4.5 + 4.5 ~ 7.2 + 7.2 + 7.2
LEV and HIC circuit
epytetalpepytetalp
5.0
1.0
17
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
Refrigerant conn. pipe
Header: CMY-Y104/108/1010-G
Joint: CMY-Y102S-G2,CMY-Y102L-G2,CMY-Y202-G2,CMY-Y302-G2
96 + 96 + 96
3.4 + 3.4 + 3.4
Installation Manual
713C49EK713C49EK713C49EK
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
1,160(1,100 without legs) x 880 x 550 1,160(1,100 without legs) x 880 x 550 1,160(1,100 without legs) x 880 x 550
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
26.3-24.9-24.0
PQHY-P700YSHM-A(For Ground source)
3-phase 4-wire 380-400-415V 50/60Hz
68,800
80.0
15.58
273,000
75,700
PQHY-P200YHM-A(For Ground source)PQHY-P250YHM-A(For Ground source)PQHY-P250YHM-A(For Ground source)
5.76 + 5.76 + 5.76
7171
Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter
6.3
retrevnIretrevnI
6.43.6
0.035(240 V)
MEL32
0.035(240 V) 0.035(240 V)
23LEM23LEM
Acrylic painted steel plateAcrylic painted steel plate Acrylic painted steel plate
R410A x 5.0kg (12lbs)
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
Over-heat protection
195(430)
epytetalp
Copper pipe,tube-in-tube structure
1.0
5.0
1.0
Copper pipe,tube-in-tube structure
12.7(1/2) Brazed
22.2(7/8) Brazed
Heat Source Twinning kit: CMY-Y300VBK2
12.7(1/2) Brazed
22.2(7/8) Brazed 19.05(3/4) Brazed
Copper pipe,tube-in-tube structure
195(430)

- 15 -
*1
*2
WkretaehesaC
WktuptuorotoM
in.
Control
Circulating water
°C
Set Model
Model
connectable
Model / Quantity
heating
Model
Total capacity
piping diameter
D.B.
*2
COP
°C
Indoor
Temp. range of
Current input
(Nominal)
mm(in.)
mm(in.)
Liquid pipe
Gas pipe
Power input
Refrigerant
BTU / h
Indoor unit
Temp. range of
*1
h/lack)lanimoN(*1
Power source
kW
cfm
l
Water volume in plate
wate r
HIC circuit (HIC: Heat Inter-Changer)
Heat exchanger
Water pressure Max.
Protection
mm
External dimension HxWxD
Type x original charge
)sbl(gkthgiewteN
MPa
High pressure protection
Inverter circuit (COMP.)
Manufacture
Starting method
L/min
Water flow rate m
3
/ h
Circulating
Compressor
Accessory
Drawing
distributor
Remarks
●Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be refer
●Turn DipSW 3-9 ON before power ON.
red to the Installation Manual.
●Due to continuing improvement, above specifications may be subject to change without notice.
●The ambient temperature of the heat source unit needs to be kept below 40 °C D.B.
●The ambient relative humidity of the heat source unit needs to be kept below 80%.
●The heat source unit should not be installed at outdoor.
●Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
●Be sure to provide interlocking for the unit operation and water circuit.
●Add brine to circulating water when a unit is operating at water temperature below 10°C.
●Twinning kit is required.
kPaPressure drop
Operating volume range
m
3
/ h
Notes:
Standard attachment Document
Wiring
External
*The specification data is
subject to rounding variation.
Unit converter
Lubricant
Type x Quantity
External finish
Gas pipe mm(in.)
Cooling capacity
devices
Compressor
cooling
Circulating water
Indoor
Heating capacity
=kW x 860
=kW x 3,412
=m
3
/min x 35.31
=kg / 0.4536
kcal
BTU/h
cfm
lb
Pipe between unit and
Liquid pipe mm(in.)
Sound pressure level (measured in anechoic room)
dB <A>
W.B.
kW / kW
kcal / h
*2 BTU / h
Power input
kW
POC kW / kW
kW
Current input
kW
A
A
Optional parts
Refri gerant
1.<Standard CITY MULTI indoor unit>
Nominal cooling conditions(subject to JIS B8615-1)
Indoor:27°CDB/19°CWB(81°FDB/66°FWB)
Water temperature:30°C(86°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
2.<PWFY-P100/200VM-E-AU>
Nominal cooling conditions
Circulating water Temp. : 30°C (86°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 23°C
Water flow rate : 1.93m
3
/h (P100) / 3.86m
3
/h (P200)
Brine concentration 0%
Nominal heating conditions(subject to JIS B8615-1)
Indoor:20°CDB(68°FDB)
Water temperature:20°C(68°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
Nominal heating conditions
Circulating water Temp. : 20°C (68°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 30°C
Water flow rate : 2.15m
3
/h (P100) / 4.30m
3
/h (P200)
Brine concentration 0%
Over-heat protection, Over-current protection Over-heat protection, Over-current protection
91.5
30.8-29.3-28.2
4.94
-5.0~45.0°C(23~113°F)
95.0
15.0~24.0°C(59~75°F)
54
15.0~27.0°C(59~81°F)
50~130 % of heat source unit capacity
P15~P250 / 2~50
-5.0~45.0°C(23~113°F)
12.7(1/2) Brazed
324,100
18.27
195(430)
KB94T659
Over-heat protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
Over-heat protection, Over-current protection
R410A x 5.0kg (12lbs) R410A x 5.0kg (12lbs)
Over-heat protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
5.0
19.05(3/4) Brazed
34.93(1-3/8) Brazed
4.5 + 4.5 + 4.5 ~ 7.2 + 7.2 + 7.2
LEV and HIC circuit
epytetalpepytetalp
5.0
1.0
17
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
Refrigerant conn. pipe
Header: CMY-Y104/108/1010-G
Joint: CMY-Y102S-G2,CMY-Y102L-G2,CMY-Y202-G2,CMY-Y302-G2
96 + 96 + 96
3.4 + 3.4 + 3.4
Installation Manual
713C49EK713C49EK713C49EK
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
1,160(1,100 without legs) x 880 x 550 1,160(1,100 without legs) x 880 x 550 1,160(1,100 without legs) x 880 x 550
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
29.0-27.5-26.5
PQHY-P750YSHM-A(For Ground source)
3-phase 4-wire 380-400-415V 50/60Hz
73,100
85.0
17.19
290,000
81,700
PQHY-P250YHM-A(For Ground source) PQHY-P250YHM-A(For Ground source) PQHY-P250YHM-A(For Ground source)
5.76 + 5.76 + 5.76
7171
Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter
6.3
retrevnIretrevnI
3.63.6
0.035(240 V)
MEL32
0.035(240 V) 0.035(240 V)
23LEM23LEM
Acrylic painted steel plateAcrylic painted steel plate Acrylic painted steel plate
R410A x 5.0kg (12lbs)
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
Over-heat protection
195(430)
epytetalp
Copper pipe,tube-in-tube structure
1.0
5.0
1.0
Copper pipe,tube-in-tube structure
12.7(1/2) Brazed
22.2(7/8) Brazed
Heat Source Twinning kit: CMY-Y300VBK2
12.7(1/2) Brazed
22.2(7/8) Brazed 22.2(7/8) Brazed
Copper pipe,tube-in-tube structure
195(430)

- 16 -
*1
*2
WkretaehesaC
WktuptuorotoM
in.
Control
Circulating water
°C
Set Model
Model
connectable
Model / Quantity
heating
Model
Total capacity
piping diameter
D.B.
*2
COP
°C
Indoor
Temp. range of
Current input
(Nominal)
mm(in.)
mm(in.)
Liquid pipe
Gas pipe
Power input
Refrigerant
BTU / h
Indoor unit
Temp. range of
*1
h/lack)lanimoN(*1
Power source
kW
cfm
l
Water volume in plate
wate r
HIC circuit (HIC: Heat Inter-Changer)
Heat exchanger
Water pressure Max.
Protection
mm
External dimension HxWxD
Type x original charge
)sbl(gkthgiewteN
MPa
High pressure protection
Inverter circuit (COMP.)
Manufacture
Starting method
L/min
Water flow rate m3/ h
Circulating
Compressor
Accessory
Drawing
distributor
Remarks
●Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be refer
●Turn DipSW 3-9 ON before power ON.
red to the Installation Manual.
●Due to continuing improvement, above specifications may be subject to change without notice.
●The ambient temperature of the heat source unit needs to be kept below 40 °C D.B.
●The ambient relative humidity of the heat source unit needs to be kept below 80%.
●The heat source unit should not be installed at outdoor.
●Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
●Be sure to provide interlocking for the unit operation and water circuit.
●Add brine to circulating water when a unit is operating at water temperature below 10°C.
●Twinning kit is required.
kPaPressure drop
Operating volume range
m3/ h
Notes:
Standard attachment Document
Wiring
External
*The specification data is
subject to rounding variation.
Unit converter
Lubricant
Type x Quantity
External finish
Gas pipe mm(in.)
Cooling capacity
devices
Compressor
cooling
Circulating water
Indoor
Heating capacity
=kW x 860
=kW x 3,412
=m3/min x 35.31
=kg / 0.4536
kcal
BTU/h
cfm
lb
Pipe between unit and
Liquid pipe mm(in.)
Sound pressure level (measured in anechoic room)
dB <A>
W.B.
kW / kW
kcal / h
*2 BTU / h
Power input
kW
POC kW / kW
kW
Current input
kW
A
A
Optional parts
Refri gerant
1.<Standard CITY MULTI indoor unit>
Nominal cooling conditions(subject to JIS B8615-1)
Indoor:27°CDB/19°CWB(81°FDB/66°FWB)
Water temperature:30°C(86°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
2.<PWFY-P100/200VM-E-AU>
Nominal cooling conditions
Circulating water Temp. : 30°C (86°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 23°C
Water flow rate : 1.93m
3
/h (P100) / 3.86m
3
/h (P200)
Brine concentration 0%
Nominal heating conditions(subject to JIS B8615-1)
Indoor:20°CDB(68°FDB)
Water temperature:20°C(68°F)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
Brine concentration 0%
Nominal heating conditions
Circulating water Temp. : 20°C (68°F)
Pipe length : 7.5 m (24-9/16 ft)
Level difference : 0m (0ft)
Inlet water Temp 30°C
Water flow rate : 2.15m
3
/h (P100) / 4.30m
3
/h (P200)
Brine concentration 0%
28.4
35.0-33.2-32.0
4.69
-5.0~45.0°C(23~113°F)
100.0
15.0~24.0°C(59~75°F)
54
15.0~27.0°C(59~81°F)
50~130 % of heat source unit capacity
P15~P250 / 2~50
-5.0~45.0°C(23~113°F)
12.7(1/2) Brazed
341,200
20.74
195(430)
KB94T659
Over-heat protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
Over-heat protection, Over-current protectionOver-heat protection, Over-current protectionOver-heat protection, Over-current protection
R410A x 5.0kg (12lbs) R410A x 5.0kg (12lbs)
Over-heat protection
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
5.0
19.05(3/4) Brazed
34.93(1-3/8) Brazed
4.5 + 4.5 + 4.5 ~ 7.2 + 7.2 + 7.2
LEV and HIC circuit
epytetalpepytetalp
5.0
1.0
17
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
Refrigerant conn. pipe
Header: CMY-Y104/108/1010-G
Joint: CMY-Y102S-G2,CMY-Y102L-G2,CMY-Y202-G2,CMY-Y302-G2
96 + 96 + 96
3.4 + 3.4 + 3.4
Installation Manual
713C49EK713C49EK713C49EK
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
1,160(1,100 without legs) x 880 x 550 1,160(1,100 without legs) x 880 x 550 1,160(1,100 without legs) x 880 x 550
45-11/16(43-5/16 without legs) x 34-11/16 x 21-11/16
32.3-30.7-29.6
PQHY-P800YSHM-A(For Ground source)
3-phase 4-wire 380-400-415V 50/60Hz
77,400
90.0
19.18
307,100
86,000
PQHY-P250YHM-A(For Ground source)PQHY-P250YHM-A(For Ground source)PQHY-P300YHM-A(For Ground source)
5.76 + 5.76 + 5.76
7171
Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter
7.4
retrevnIretrevnI
3.63.6
0.035(240 V)
MEL32
0.035(240 V) 0.035(240 V)
23LEM23LEM
Acrylic painted steel plateAcrylic painted steel plate Acrylic painted steel plate
R410A x 5.0kg (12lbs)
High pressure sensor, High pressure switch at 4.15MPa (601 psi)
Over-heat protection
195(430)
epytetalp
Copper pipe,tube-in-tube structure
1.0
5.0
1.0
Copper pipe,tube-in-tube structure
12.7(1/2) Brazed
22.2(7/8) Brazed
Heat Source Twinning kit: CMY-Y300VBK2
12.7(1/2) Brazed
22.2(7/8) Brazed 22.2(7/8) Brazed
Copper pipe,tube-in-tube structure
195(430)