Mitsubishi Electric JT-SB116JH2-W-NA User manual

EnglishFrançais
−NA -1 −
This product is intended for the purpose of drying hands and is not covered by the warranty if used for any other purpose.
It has no sterilizing or disinfecting functions.
Input Power: 120 Vac Single-phase
Indoor use only
－1－
You should not attempt to install the unit yourself, as this may affect the safety and functionality of the unit.
INSTRUCTION MANUAL For User
Hand dryer
■Read this manual thoroughly before use to ensure the unit is used safely and correctly.
After reading the manual, store it in an easily accessible location for future reference.
INDEX
Safety Precautions ……………………………………………… 2
■Names of Parts ……………………………………………………… 3
How to use the unit ……………………………………………… 3
■Turning the power on ……………………………………………… 3
■After washing hands ………………………………………………… 3
■If not using for a long period ……………………………………… 3
Maintenance ……………………………………………………… 4
1. Cleaning the unit and hand drying area ………………… 4
2. Cleaning the air filter ……………………………………… 5
3. Draining and cleaning the drain tank……………………… 5
4. Cleaning the drain pipe …………………………………… 6
If you think something has gone wrong ……………………… 7
Specifications …………………………………………………… 8
■Drying times for different modes (approximate) and uses ……… 8
1606876HE3501
MODEL
JT-SB116JH2-W-NA
JT-SB116JH2-S-NA
Model Name
display position.
Power voltage
display position.
Unit color -W (White), -S (Silver)

English
−NA -3 −− NA -2 −
Warning The following may lead to death or serious
personal injury if handled incorrectly
Caution
The following may lead to injury or damage to
property if the unit is handled incorrectly.
－2－
•Do not open the front panel.
Doing so may result in an electric shock.
•
Do not use at locations where salt damage may occur, or
where corrosive, neutral, or reductive gases are present.
The above may cause fire, electric shocks or malfunctions.
•This unit is not intended for use by young children
or infirm persons unless they are adequately
supervised by a responsible person to ensure that
they can use the unit safely.
•
Young children should be supervised to ensure
that they do not play with the unit.
•Do not use for drying anything other than hands.
Inappropriate use may cause an accident.
•Do not modify or disassemble the unit.
Doing so may cause fires, electric shocks or injury.
•When changing the installation place, consult
your dealer or installer.
There is a risk of injury.
•Always use the unit with the drain tank, air filter,
and side cover attached.
Any water entering the unit may cause short circuits,
electric shocks or damage.
•If the unit stops working or begins acting
strangely, turn the breaker off then contact your
dealer or contractor.
Failure to do any of the above may cause electric
shock or fire through short circuit.
•Use 120 Vac power.
Using the incorrect power supply may cause fires,
fumes, electric shocks or malfunctions.
•Use exclusive wiring.
Using this unit with other devices on a branch socket
may cause abnormal heat, which may cause fires.
•Always turn off the power during maintenance
work.
Failure to do so may result in an electric shock.
•
Do not use in a shower room or other locations with a
great deal of humidity in the air, or where condensation
may form on the unit.
This may cause electric shocks or malfunctions.
•Wear rubber gloves when cleaning the unit.
Not doing so may result in injuries.
•Do not douse the unit with excessive amounts
of water.
This may cause electric shocks or malfunctions.
Prohibited
Prohibited
Safety Precautions
Do not use in the
bathroom/
shower room
Do not allow the
unit to get wet
Do not
disassemble
Follow
instructions
Follow
instructions
Follow
instructions
Note •Do not use in the following locations.
•Outdoors •Locations where the temperature could be lower than 50ºF (10ºC). •Locations where there is a lot
of dust. •Locations where the temperature could be higher than 104ºF (40ºC). •Locations where there is a lot of
condensation. •Locations where salt damage may occur. •Vehicles (including ships and airplanes)
•Locations where the unit is in direct or strong sunlight. (May cause the sensor to malfunction.)
•Near food or tableware. •Locations where the unit may come into direct contact with water. •Kitchens
(Where there is a risk of water splashing.)
•Locations where corrosive, neutral, or reductive gases are present.
(This may shorten the working life of the unit and/or cause malfunctions.)
•Rooms that have a sterilization basin, swimming pools, bathrooms.
•Do not use with chemicals on your hands.
(This may damage the surface of the unit, or cause discoloration or cracking.)
•Be sure to completely wipe off any detergents or chemicals on the unit.
(Failure to do so may damage the surface of the unit, or cause discoloration or cracking.)
•Only use the specified cleaning agents.
(For details on detergents, see the "Maintenance" section.)
•
If water is sucked into the unit, it may cause damage to the mechanism, or moisture may be absorbed into the soundproofing
material, allowing bacteria to breed. Therefore, do not allow water to come in contact with the air filter or air duct.

English
−NA -3 −
－3－
Hand drying area
Black wall area Blue light
Main unit
•The blue light does not have a sterilizing
effect.
•Do not look directly into the blue light.
Drain tank
Side cover Front panel
Tank cover
Air filter
Display
Power lamp
Heater lamp
■Names of Parts
※Shaded areas in the figure indicate antibacterial material.
Sensor
4321
■Turn the ground-fault circuit interrupter "ON".
■After washing hands
How to use the unit
Insert hands from the side Bring hands upwardsWet hands
※Repeat 2-3 times
Automatic Stop Function
The power lamp flashes and the dryer stops automatically if the unit is used continually for more than 30 seconds.
To continue using the hand dryer, remove your hands, and then re-insert them.
Simple heater
Softens the feeling of cold air.
If the room temperature is above 80ºF (30ºC), the heater will stop working to prevent the temperature from rising too high.
NOTE •If the room temperature is less than 68ºF (20ºC), the air may feel cold.
■If not using for a long period
Then turn the breaker off.
Caution
●Do not turn the power on when your hands or an object are inside the hand drying area.
The sensitivity of the sensor may be reduced if the power is turned on while your hands or objects are inside the
hand drying area.
If the sensitivity of the sensor is reduced, please turn the power off and then back on after one minute.

English
−NA -5 −− NA -4 −
Cautions •Only use cleaning products that are labeled as safe "Safe to use on plastics".
•Do not use any of the following cleaning materials.
(They may damage the surface of the unit, or cause discoloration or cracking.)
•Solvents such as thinner or benzene •
Acid, alkaline or chlorine detergents
•Mold and mildew removers •Citrus-based or other plant-based detergents
•Nylon scourers or abrasives •Antiseptics
•Do not clean the front panel with alcohol.(Only JT-SB116JH2-S-NA)
(This may damage the surface of the unit, or cause discoloration or cracking.)
※"Alcohol" means a disinfectant with an ethanol content of 83% or less.
※Be sure to dispose of any alcohol that has collected in the drain tank.
※Do not spray alcohol directly onto the unit.
Damage to the unit (such as rusting) is not covered by the warranty if the above cautions are not observed.
Hand drying area
Sensor
Front panel
Black wall area
－4－
•
When cleaning the unit, use a neutral detergent. (pH: 6-8)
•
The exterior of the unit can be wiped with alcohol. (Excluding the front panel)
•
After cleaning with neutral detergent or alcohol, be sure to wipe away all remaining traces of the detergent or alcohol.
•
After wiping the unit clean with alcohol, be sure to dispose of any alcohol that has collected in the drain tank.
※Do not spray alcohol directly onto the unit.
•
When using a chemical cloth, be sure to follow the instructions carefully.
Warning Caution
•Always turn off the power during maintenance work.
Failure to do so may result in an electric shock.
•Do not douse the unit with excessive amounts of water.
This may cause electric shocks or malfunctions.
•
Wear rubber gloves when cleaning the unit.
Not doing so may result in injuries.
Cleaning the unit and hand drying area
1
Maintenance
Wipe with a well-wrung wet cloth
NOTE
•After cleaning with neutral detergent or alcohol,
be sure to wipe away all remaining traces of the
detergent or alcohol.
•Clean the sensor area about once a week.
If it is particularly dirty (at least once a week)
NOTE
Cleaning the drain pipe
4At least once a week
• Gently wipe any dirt from the drain using a soft cloth.
• Do not pour water directly onto the drain pipe.
NOTE
Cautions • Ensure that the side cover is fitted properly.
Drain
collection
outlet
Drain pipe
4 After cleaning, attach the side cover.
－6－
Drain collection
outlet
Drain pipe
Handle Drain hole
2 Hook your fingers into the handle on the
side cover, and pull it diagonally upwards
1 Turn the ground-fault circuit interrupter "OFF".
3 Wipe the inside of the side cover and
drain pipe with a well-wrung wet cloth
Side cover (inside)

English
−NA -5 −
Cleaning the drain pipe
4At least once a week
• Gently wipe any dirt from the drain using a soft cloth.
• Do not pour water directly onto the drain pipe.
NOTE
Cautions • Ensure that the side cover is fitted properly.
Drain
collection
outlet
Drain pipe
4 After cleaning, attach the side cover.
－6－
Drain collection
outlet
Drain pipe
Handle Drain hole
2 Hook your fingers into the handle on the
side cover, and pull it diagonally upwards
1 Turn the ground-fault circuit interrupter "OFF".
3 Wipe the inside of the side cover and
drain pipe with a well-wrung wet cloth
Side cover (inside)

English
−NA -7 −− NA -6 −
Cleaning the drain pipe
4At least once a week
• Gently wipe any dirt from the drain using a soft cloth.
• Do not pour water directly onto the drain pipe.
NOTE
Cautions • Ensure that the side cover is fitted properly.
Drain
collection
outlet
Drain pipe
4 After cleaning, attach the side cover.
－6－
Drain collection
outlet
Drain pipe
Handle Drain hole
2 Hook your fingers into the handle on the
side cover, and pull it diagonally upwards
1 Turn the ground-fault circuit interrupter "OFF".
3 Wipe the inside of the side cover and
drain pipe with a well-wrung wet cloth
Side cover (inside)
－7－
Are any lamps in the display on?
Has a blackout occurred?
Has the dryer been used continually for
more than 30 seconds?
Are any lamps in the display flashing?
The heater lamp is off.
Has a blackout occurred?
The ground fault circuit interrupter is "OFF".
This may flash if there is a malfunction in
the power supply.
There is no unevenness, even when touched by hand.
(No feeling of cracking)
If the above fixes do not work, turn off the breaker, and have your dealer inspect and if necessary
repair the unit. (Costs are as agreed with the dealer.)
•Contact your dealer for any changes to
settings or adjustments etc.
Costs are as agreed with the dealer.
•Do not attempt to modify or disassemble
this unit yourself.
Air conditioning is not working.
Is the room temperature too high?
Was the ground-fault circuit interrupter turned on while
your hands or an object was inside the hand drying area?
Are you putting your hands in all the way?
Is the sensor blocked by dirt or dust?
Is the black wall area in the hand drying area white with dirt?
•Turn the ground fault circuit interrupter on.
•Contact the dealer about any changes to the settings.
Costs are as agreed with the dealer.
•If the room temperature is above 86ºF (30ºC), the
heater will stop working to prevent the temperature
from rising too high.
•Turn the ground-fault circuit interrupter on.
•Turn the breaker off, check that all of the lamps on
the display section are off, and then wait for 1 minute
before turning the breaker back on.
•This pattern occurs when the product is molded (manufactured).
It does not affect product performance, and is not a malfunction.
•The air may not feel warm if the room temperature is
less than 68ºF (20ºC).
•Turn the ground-fault circuit interrupter "OFF", and
when the display lamps all go out, remove any foreign
substances or dirt. Then turn the ground-fault circuit
interrupter "ON".
•If the hand dryer is used continually for more than 30 seconds,
the power lamp flashes, and the dryer automatically stops.
To continue using the hand dryer, remove your hands, and
then re-insert them.
•Place your hands all the way inside the hand drying area.
No air blows even if
hands are inserted
Stops operating
during hand drying
Air is cold
Air does not
warm up
The lamp does not light up
even when the ground-fault
circuit interrupter on.
The display section
lamp flashes
Crack-like shapes can be
seen around the nozzle
The operating sound is too
loud (Air blow is too strong)
I want to reduce power
consumption (want to
turn off the heater)
Air does not stop
If you think something has gone wrong
Perform the following checks and fixes.
Check FixProblem
Cautions

English
−NA -7 −
－7－
Are any lamps in the display on?
Has a blackout occurred?
Has the dryer been used continually for
more than 30 seconds?
Are any lamps in the display flashing?
The heater lamp is off.
Has a blackout occurred?
The ground fault circuit interrupter is "OFF".
This may flash if there is a malfunction in
the power supply.
There is no unevenness, even when touched by hand.
(No feeling of cracking)
If the above fixes do not work, turn off the breaker, and have your dealer inspect and if necessary
repair the unit. (Costs are as agreed with the dealer.)
•Contact your dealer for any changes to
settings or adjustments etc.
Costs are as agreed with the dealer.
•Do not attempt to modify or disassemble
this unit yourself.
Air conditioning is not working.
Is the room temperature too high?
Was the ground-fault circuit interrupter turned on while
your hands or an object was inside the hand drying area?
Are you putting your hands in all the way?
Is the sensor blocked by dirt or dust?
Is the black wall area in the hand drying area white with dirt?
•Turn the ground fault circuit interrupter on.
•Contact the dealer about any changes to the settings.
Costs are as agreed with the dealer.
•If the room temperature is above 86ºF (30ºC), the
heater will stop working to prevent the temperature
from rising too high.
•Turn the ground-fault circuit interrupter on.
•Turn the breaker off, check that all of the lamps on
the display section are off, and then wait for 1 minute
before turning the breaker back on.
•This pattern occurs when the product is molded (manufactured).
It does not affect product performance, and is not a malfunction.
•The air may not feel warm if the room temperature is
less than 68ºF (20ºC).
•Turn the ground-fault circuit interrupter "OFF", and
when the display lamps all go out, remove any foreign
substances or dirt. Then turn the ground-fault circuit
interrupter "ON".
•If the hand dryer is used continually for more than 30 seconds,
the power lamp flashes, and the dryer automatically stops.
To continue using the hand dryer, remove your hands, and
then re-insert them.
•Place your hands all the way inside the hand drying area.
No air blows even if
hands are inserted
Stops operating
during hand drying
Air is cold
Air does not
warm up
The lamp does not light up
even when the ground-fault
circuit interrupter on.
The display section
lamp flashes
Crack-like shapes can be
seen around the nozzle
The operating sound is too
loud (Air blow is too strong)
I want to reduce power
consumption (want to
turn off the heater)
Air does not stop
If you think something has gone wrong
Perform the following checks and fixes.
Check Fix
Problem
Cautions

−NA -1 −− NA -8 −
－8－
Specifications
Model Voltage Frequency Power Input Current Weight Dimensions (WxDxH)
JT-SB116JH2-W-NA ※
JT-SB116JH2-S-NA ※120 Vac 60Hz 1250 W 11.4 A 26.5 lbs
(12 kg)
11
13
⁄
16
"×8
5
⁄
8
"×26
3
⁄
8
" (in.)
(300 ×219 ×670 (mm))
•The values above are when the air volume is "high". •The drain tank capacity is 1.7pt. (0.8ℓ). ※With simple heater.
■Drying times for different modes (approximate) and uses
Mode Drying times (approximate) ※Noise Use
HIGH 9~11secs approx. 59dB To dry hands quickly
STANDARD 11~13secs approx. 56dB To achieve both quick drying and low noise
※Drying times are based on Mitsubishi measurements. (50mg of water per hand)
User Inspection
Be Sure to inspect older hand dryers.
Things
to look
for
• The unit does not stop blowing air.
• The air power is unstable.
There is a burn odor.
• The leakage circuit breaker shuts dff.
• There is unusual noise or vibration during operation.
• Othere abnomalities or malfunctions.
Stop
using
the unit
Cut off power to the unit using the circuit
breaker to avoid accidents or injury.
Make sure to contact your dealer and
consult about inspection and repair costs.
English