Mitsubishi Electric JT-MC206GS-W-E User manual

−1−
GB
MODEL
JT-MC206GS-W-E
Unit color -W（White）
Hand dryer
1209875HF0501
Read the manual thoroughly before beginning installation to ensure the unit is installed safely and correctly.
Local installation standards should be obeyed and installation should be performed by the dealer or a qualified
professional.
The "INSTRUCTION MANUAL" is for the customer. Be sure to hand it to the customer.
INDEX
Safety Precautions 2
Pre-installation checks 3
■Checking the installation environment 3
■Checking the unit, accessories
and items required for installation 3
Names of parts and external dimensions 4
Installation conditions 5
■Required space for installation 5
■Suitable walls 5
■Making the unit easier to use 5
Installation method 6 – 9
Test Run 10
Initial setting checks 11
■How to open/close the front cover 11
Precautions for when opening/closing
the front cover 11
■Turning the heater on 12
■Adjusting the air speed 12
INSTALLATION MANUAL
Location of Model Name display
Location of power supply voltage display
Single-phase 220 – 240V AC
For Dealers and Installers

−2−
Safety Precautions
󱾀The dangers arising from improper handling and the extents of the dangers are classified and explained as
shown below.
Prohibited
󱾀Do not install in locations where they
may be leakages of combustible gas.
This may cause fires.
󱾀Do not install in locations where salt
damage may occur or where corrosive,
neutral or reductive gases are present.
This may cause malfunctions.
󱾀Do not scratch, damage, process,
excessively bend, pull, twist or bundle
the power cable.
Please also refrain from placing heavy
objects onto it or trapping it.
Failure to do so may damage the power
cable, causing fires or electric shocks.
Important !
Follow
instructions.
󱾀Wiring work is to be done by a certified
electrical worker in accordance with
technical standards for electrical
equipment and internal wiring
regulations.
Incorrect wiring work may cause electric
shocks or fires.
󱾀Use single-phase 220 – 240V AC power.
Using the incorrect power supply
may cause fires, electric shocks or
malfunctions.
󱾀Use exclusive wiring for the power
source.
Using this unit with other devices on a
branch socket may cause abnormal heat,
which may cause fires.
󱾀Be sure to attach the ground fault
circuit interrupter.
Failure to do so may result in electric
shocks.
󱾀The unit shall be installed in
accordance with national wiring
regulations.
󱾀A means for disconnection must be
incorporated in the fixed wiring in
accordance with wiring rules.
󱾀The disconnecting device shall be of
all-pole disconnection.
Do not
disassemble
󱾀Do not attempt any disassembly or
modification of the unit that is not
expressly stated in this manual.
Doing so may result in fires, electric
shocks or injuries.
Do not use
in the baths/
shower room.
󱾀Do not use in a hot location such as a
shower room, where condensation may
form on the unit or where water may
splash directly onto the unit.
This may cause electric shocks or
malfunctions.
Warning The following may lead to death or serious
personal injury if handled incorrectly.
Prohibited
󱾀Do not install when the unit (power
cable) is electrified.
Doing so may result in electric shocks. Important !
Follow
instructions.
󱾀Install securely in a location strong
enough to support the weight of the
unit.
Injuries may be caused if the unit falls off
the wall.
󱾀Wear gloves when installing the unit.
Not doing so may result in injuries.
Caution The following may lead to minor injuries or damage
to property if the unit is handled incorrectly.

−3−
Pre-installation checks
󱾀Single-phase 220 –240V AC power is used.
Using the incorrect power supply may cause fires, electric shocks or malfunctions.
■Checking the installation environment
Do not install the unit in the following types of locations.
(This may cause malfunctions.)
󱾀 Outdoors 󱾀 Locations where the temperature could be lower than 0C.
󱾀 Locations where there is a lot of dust. 󱾀 Locations where the temperature could be higher than 40C.
󱾀 Locations where there is a lot of condensation. 󱾀 Locations where salt damage may occur.
󱾀 Locations where the unit is in direct or strong sunlight (may cause the sensor to malfunction).
󱾀 In vehicles (including ships and airplanes)
󱾀 Locations where corrosive, neutral or reductive gasses are present.
(This may shorten the working life of the unit and/or cause malfunctions.)
󱾀 Near food or tableware 󱾀 Locations where the unit may come into direct contact with water.
󱾀 Kitchens
(Where there is a risk of water splashing.)
󱾀 Rooms that have a sterilization basin, swimming pools and baths.
■Checking the unit, accessories and items required for installation
※Shaded areas in the figure indicate antibacterial material (excluding outlet nozzle areas).
Main unit
Air filter
Open
Lid
Drain tank
How to open/close the front cover
(refer to Page 11)
Mounting screws 6
(5×30 Type 1 tapping screws)
Installation panel 1
Cord clip mounting screw
(4×14) 1
Cord clip 1
Screwdriver Pen
Screw anchor 6 Wall reinforcement
※To mark position to insert metal
screw plugs in the wall.
※Use on concrete walls ※Reinforces walls made of
materials other than concrete.
■Prepare if required
※Not needed if the internal wiring is
complete.
Single wire for internal wiring
(Cable core: between 2.0mm² and 3.0mm²)
Warning
Front cover
Unit
Required items
Accessories

−4−
42
100
163
2 170
215190
458
480
190
3116
60
16.5
21
250
Names of parts and external dimensions
■Main unit
■Front
Installation panel
Power cord hole (rear)
Air filter
Power
light
Drain tank
Unit (mm)
󱾀Confirm the details in the "Installation conditions" (Page 5).
Power light
Front
cover
Nozzle
Sensor
Hand drying
area
Lid
Drain tank
Water
receiver
area
Inside the front cover
Air filter Power switch Setting switches
Front cover Open
Air speed
light
Air speed
switch
Heater light
Heater
switch
Power light
■Rear
Power cord hole
Main unit
󱾀Open the front cover while referring to "How to open/close the front cover" (Page 11).
󱾀Please refer to "Turning the heater on" (Page 12) while turning the heater on/off.
󱾀Please refer to "Adjusting the air speed" (Page 12) while adjusting the air speed.
NOTE
NOTE

−5−
54
169
A
B
437
40
10
60
143
7
R3.5
140
40
160
Installation conditions
■Required space for installation
Caution Be sure to secure at least the
distances listed in the right-
hand table from walls, flammable
(combustible) materials and so
on.
■Suitable walls
󱾀When installing on a wall, select a wall with a flat
and even surface.
󱾀When installing on a concrete wall, use commercially
available metal screw plugs.
󱾀Reinforce any walls made with materials other than
concrete before installation.
■Making the unit easier to use
󱾀Refer to the "Installation position guide" and
"Installation diagram" while installing the unit in order
to make it easier to use.
If it is installed at a low position, it may become wet
when the sink is being washed. If water enters the
unit, it may cause damage or cause the acoustic
materials to absorb water and allow bacteria to grow.
󱾀Do not install the main unit in locations such as
those near mirrors or walls. This may lead to water
drops flying to undesirable areas during the drying
of the hands.
󱾀Do not install the main unit in locations such as
those near food or eating utensils. This may lead to
water drops flying to undesirable areas during the
drying of the hands.
󱾀Avoid locations where people or doors might bump
into the unit.
※When installed above a sink
Rear side
Top side
Left side
Main
unit
Right
side
Bottom side
Unit (mm)
Location Isolation
distance
Above 150
Left 100
Right 150
Front Open
Below 50
■Installation position guide
Installation
panel
Guide from floor to
installation position
Men : 1290
Women: 1190
When there is a sink,
570 from the top of
the sink should be the
approximate distance.
Unit (mm)
■Installation diagram
Installation panel
Installation hole in detail Top side of
sink, etc.
Floor surface
Mounting hole position
below the unit
Conduit box
Recommended A and B measurements during installation
Unit (mm)
Space below the unit ＡＢ
When there are no objects below Men 1290 −
Women 1190 −
When there is an object such as a sink −−570
Unit (mm)

−6−
160
140
60
54115
40
40
71.5 71.5
437
A
54
169
A
B
437
40
10
60
143
7
R3.5
140
40
160
Installation method
For confirmation
□Single-phase 220 –240V ACpower is being used (using the incorrect power supply may cause fires, electric
shocks or malfunctions).
□The ground fault circuit interrupter is attached (not attaching a ground fault circuit interrupter may result in
electric shocks).
□A single wire (cable core: 2.0mm² or 3.0mm²) is being used for the power cable.
Warning
󱾀Single-phase 220 – 240V AC power is used.
Using the incorrect power supply may cause fires, electric shocks or
malfunctions.
Caution
󱾀 Do not install when the unit (power
cable) is electrified.
Doing so may result in electric
shocks.
1
2
Confirm that the severing of wires
during fixed wiring work is in
accordance with wiring regulations.
󱾀Follow the illustration on the right for the
internal wiring.
󱾀The power cable forces out the main unit
and does not allow proper installation if the
conduit box is not used.
Power cable
Terminal
block
Conduit box
About 360
Power cord hole (rear)
Unit external shape
Mounting hole position
below the unit Unit (mm)
Fix the installation panel onto the wall
with 4 accessory mounting screws
(5×30).
󱾀The "Installation position guide" illustrated on
the right is recommended.
󱾀When installing on a wall, select a wall with a
flat and even surface.
󱾀When installing on a concrete wall, use
commercially available metal screw plugs.
󱾀Reinforce any walls made with materials
other than concrete before installation.
※When installing above a sink, the
recommended B measurement is 570mm
above the sink.
Installation panel
Mounting screws (5×30)
(Accessories)
■Installation position guide
Installation panel
Unit (mm)
Installation hole
in detail
Top side
of sink,
etc.
Floor
surface
Mounting hole position
below the unit
Conduit box
Recommended A and B measurements during installation Unit (mm)
Space below the unit ＡＢ
When there are no objects below Men 1290 −
Women 1190 −
When there is an object such as a sink −−570

−7−
3
Installation method - continuation
1. Remove the drain tank.
2. Open the front cover and remove the
air filter.
※Refer to "How to open/close the front cover"
(Page 11).
3. Remove the main unit panel
mounting screw (1).
4. Unlock the upper tabs (2 locations)
of the main unit panel, and remove
the main unit panel from the base.
5. Remove the terminal block cover
mounting screw (1), and remove the
terminal block cover.
※Be careful not to lose the cord bushing.
Drain tank
Air filter Air filter
Open
Main unit
panel
Main unit panel
mounting screw
Main
unit panel
Base
Main unit panel
Ta b
Base
Base
Cord bushing.
Terminal block cover
Terminal block cover
mounting screw
Pull the tab and open the front
cover.
Ta b
Front cover

−8−
L
N
4
Installation method - continuation
5
1. Push the power cable for exclusive
wiring through the power cord hole
at the rear of the base.
2. Engage the base with the 2 hooks on
the installation panel.
3. Check that the power cable is not
trapped behind the base.
Base
Power cable
Power cord hole
Power cord hole
Power cable
Conduit
box
Installation
panel
Panel hooks
(2 locations)
Warning
󱾀Single-phase 220-240V AC power is used.
Using the incorrect power supply may cause fires, electric shocks
or malfunctions.
Caution
󱾀Make sure that the main unit
does not fall as the base is not
attached to the wall with screws.
Injuries may be caused if the unit
falls off the wall.
Wire the power cable to the terminal block.
(No polarity)
1. Remove 12mm (single wire) or 8mm
(stranded wire) of wire sheath from
the end.
2.
Fix the power cable to the terminal block.
󱾀When stranded wire is used for the power
cable, attach an insulated ring tongue terminal
using an appropriate tool.
󱾀Proper torque is 1.5N·m
3. Check that the power cable is
securely fixed to the terminal block.
4. Use the cord clip mounting screw
hole to fix the power cable with the
accessory cord clip and mounting
screw (4 ×14).
󱾀Proper torque is 1.5N·m
󱾀Fix it where the external wire sheath of the
power cable is when it is fixed in the cord clip
mounting position.
󱾀Do the wiring so that the power cable goes
through the right side of the circuit case.
The main unit panel may not be able to be
attached if it is above the circuit case.
Terminal block
Base
Circuit case Power cable
Terminal block
Screw
Base
Cord clip
mounting
screw hole
Circuit case
Power cable
Cord clip
mounting screw
(4×14)
(Accessory)
Cord clip
(Accessory)
Insulated ring
tongue terminal
■Single wire
■Stranded wire
Unit (mm)

−9−
12
6
Installation method - continuation
7
1. Place the power cable through the
cord bushing and reattach it to the
circuit case with the terminal block
cover mounting screw.
2. Check that the power cable and wires
are not pinched anywhere.
1. Insert the tabs (2 locations) of the
main unit panel into the locks of the
base hooks and fix it with screw (1).
󱾀The screw is inside the front cover.
2. Check that the 2 hooks on the main
unit panel are hooked in the base.
3. Gently press the unit against the wall,
and fix it in place using 2 accessory
mounting screws (5×30).
󱾀When installing on a concrete wall, use
commercially available metal screw plugs with
the procedures below before fixing the front
cover onto the base.
①Temporarily place the main panel on the
base.
②Mark the position of the hole in the wall
through the mounting screw hole with a
pen.
③Remove the main unit panel and insert
commercially available metal screw plugs
into the marked locations of the wall.
󱾀Reinforce any walls made with materials other
than concrete before installation.
8
Base
Terminal block
cover mounting
screw
Terminal
block cover
Cord
bushing
Main unit panel
Ta b
Base
Base
Main unit panel
Front cover
Main unit panel
mounting screw
Main unit
panel
Installation
hole
Mounting screws
(5×30)
(Accessories)
Plugging marks
on the wall
Plug positioning
Mounting screws
(5×30)
(Accessories)
Mark the wall in
2 places
Air filter
Main unit
panel
Front cover
Drain tank
Gap
①Close the right side ②Close the left side
(both the upper and lower parts)
1. Open the front cover and attach the air filter.
2. Close the front cover and push the tab into
latch the front cover shut.
3. Check that the front cover is securely closed.
Caution 󱾀Check to see that the front cover is fitted
securely.
Press against the front cover so that it is
firmly closed against the main panel.
※Refer to "How to open/close the front
cover" (Page 11).
4. Attach the drain tank.
Pull the tab for opening the
front cover.
Circuit case
Ta b

−10 −
Test Run
Step What to check for Check
1Check the power supply
voltage
Is the proper power being used?
(JT-MC206GS-W type: Single-phase 220 – 240V AC )
Incorrect power supply may cause malfunctions or low
wind power.
2Turn the ground fault circuit
interrupter on.
3Turn the power switch "ON".
(page 4) Are any lights in the display on?
4Insert your hands to check if air is
being blow. (page 4) Is the air blowing?
5Press the air speed switch while
one hand is inside. (page 12) Has the air speed changed?
6Turn the heater switch "ON".
(page 12)
Is warm air blowing?
(Even if the heater switch is "ON", the heater may not operate if
it is used continually.)
※As the heater is a simple heater, the air may not feel so
warm if the room temperature is low (20C or below).
7Is the unit mounted securely without any vibration or abnormal
noises?
󱾀The air speed light and heater light turn off after about 10 seconds. When the air speed switch or heater switch are
pressed again, the lights in the display section turn back on in the state where the settings have been made.
Caution
󱾀If the power light flashes, turn the power switch "OFF", check that power light is off, and then wait for 1 minute before
switching the power back "ON".