Mitsubishi Electric GT15V-75V4R1 User manual

User's Manual
Thank you for choosing Mitsubishi Electric Graphic Operation Termi-
nal (GOT).
MODEL GT15V-75V4R1 Video/RGB Input Unit
MODEL GT15V-75V4 Video Input Unit
MODEL GT15V-75R1 RGB Input Unit
Prior to use, please read both this manual and detailed manual
thoroughly to fully understand the product.
MODEL GT15V-75V4R1-U
MODEL
CODE 1D7M54
IB(NA)-0800348-G(1706)MEE

A-1
SAFETY PRECAUTIONS
(Always read these precautions before using this equipment.)
Before using this product, please read this manual and the relevant manuals
introduced in this manual carefully and pay full attention to safety to handle the
product correctly.
The precautions given in this manual are concerned with this product. In this
manual, the safety precautions are ranked as "WARNING" and "CAUTION".
Note that the caution level may lead to a serious accident according to the
circumstances. Always follow the instructions of both levels because they are
important to personal safety.
Please save this manual to make it accessible when required and always forward
it to the end user.
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal
injury or physical damage.
WARNING
CAUTION

A-2
[DESIGN PRECAUTIONS]
[MOUNTING PRECAUTIONS]
Do not bunch the control wires or communication cables with the main circuit
or power wires, or lay them close to each other.
As a guide, separate the lines by a distance of at least 100mm (3.94 inches)
otherwise malfunctions may occur due to noise.
Be sure to shut off all phases of the external power supply used by the system
before mounting or removing this unit onto/from the GOT.
Not doing so can cause the unit to fail or malfunction.
Use this unit in the environment that satisfies the general specifications
described in the User's Manual for the GOT used.
Not doing so can cause an electric shock, fire, malfunction or product damage
or deterioration.
Tighten the mounting screws within the specified torque range.
Undertightening can cause the GOT to drop, short circuit or malfunction.
Overtightening can cause a drop, short circuit or malfunction due to the
damage of the screws or the GOT.
Do not touch the conductive and electronic parts of the unit directly.
Doing so can cause a unit malfunction or failure.
CAUTION
WARNING
CAUTION

A-3
[WIRING PRECAUTIONS]
Be sure to shut off all phases of the external power supply used by the system
before wiring.
Failure to do so may result in an electric shock, product damage or
malfunctions.
Exercise care to avoid foreign matter such as chips and wire offcuts entering
the GOT. Not doing so can cause a fire, failure or malfunction.
Make sure to securely connect the cable to the connector of unit.
Incorrect connection may cause malfunctions.
Do not hold the cable by hand and pull it out from the unit.
When removing the cable from the unit, make sure to hold the connector by
hand and pull it.
Failure to do so may cause malfunctions or damage to the unit or cable.
Solder the coaxial cable connector correctly.
Incomplete soldering may cause a malfunction.
WARNING
CAUTION

A-4
[STARTUP/MAINTENANCE PRECAUTIONS]
[DISPOSAL PRECAUTIONS]
[TRANSPORTATION PRECAUTIONS]
When power is on, do not touch the terminals.
Doing so can cause an electric shock or malfunction.
Before starting cleaning, always shut off GOT power externally in all phases.
Not doing so can cause a unit failure or malfunction.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of
the screws or unit.
Do not disassemble or modify the unit.
Doing so can cause a failure, malfunction, injury or fire.
Do not drop the module or subject it to strong shock.
A module damage may result.
Before touching the unit, always touch grounded metal, etc. to discharge static
electricity from human body, etc.
Not doing so can cause the unit to fail or malfunction.
When disposing of the product, handle it as industrial waste.
Make sure to transport the GOT main unit and/or relevant unit(s) in the
manner they will not be exposed to the impact exceeding the impact
resistance described in the general specifications of the User's Manual for the
GOT used, as they are precision devices.
Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
WARNING
CAUTION
CAUTION
CAUTION

A-5
REVISIONS
* The manual number is noted at the lower right of the top cover.
© 2006 MITSUBISHI ELECTRIC CORPORATION
Print Date *Manual Number Revision
Mar., 2006 IB(NA)-0800348-A First edition
Feb., 2007 IB(NA)-0800348-B
Chapter1, Section 2.4.1
Compliance with the EMC and Low
Voltage Directives
Jul., 2007 IB(NA)-0800348-C
Compliance with the EMC and Low
Voltage Directives, Chapter 2, 3, 4
Jun., 2009 IB(NA)-0800348-D
Compliance with the EMC and Low
Voltage Directives
Jun., 2011 IB(NA)-0800348-E
Compliance with the Radio Waves Act
(South Korea)
May, 2015 IB(NA)-0800348-F
Cover
Jun., 2017 IB(NA)-0800348-G
Cover
This manual confers no industrial property rights or any rights of any other kind,
nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.
Partial addition
Addition
Partial corrections
Partial corrections
Addition
Partial corrections
Partial corrections

A-6
CONTENTS
1. OVERVIEW .................................................................................................... 1
2. SPECIFICATIONS ......................................................................................... 4
2.1 Video input unit specifications ................................................................. 4
2.2 RGB input unit specifications ...................................................................5
2.3 Video/RGB input unit specifications ........................................................ 6
2.4 Cable specifications ................................................................................. 7
2.4.1 Specifications of the cables (coaxial cables) used when
displaying video images .................................................................. 7
2.4.2 Specifications of the cables (9-core combined cables) used
when displaying RGB screens ...................................................... 10
3. PART NAMES AND EXTERNAL DIMENSIONS ......................................... 11
3.1 Part names and external dimensions of the video input unit ................. 11
3.2 Part names and external dimensions of the RGB input unit .................. 12
3.3 Part names and external dimensions of the video/RGB input unit ........13
3.4 External dimensions of the extension interface relay board .................. 14
4. INSTALLATION PROCEDURE ................................................................... 15

A-7
Packing List
The following items are included.
Compliance with the EMC and Low Voltage Directives
To configure a system meeting the requirements of the EMC and Low Voltage Directives
when incorporating the Mitsubishi GOT (EMC and Low Voltage Directives compliant) into
other machinery or equipment, refer to "EMC AND LOW VOLTAGE DIRECTIVES" of the
General Description included with the GOT used.
The CE mark, indicating compliance with the EMC and Low Voltage Directives, is printed on
the rating plate of the GOT.
Model Product Quantity
GT15V-75V4
Video input unit 1
Mounting screw set (2 screws,2 stickers) 2
Extend interface relay board 1
GT15V-75R1
RGB input unit 1
Mounting screw set (2 screws,2 stickers) 2
Extend interface relay board 1
GT15V-75V4R1
Video/RGB input unit 1
Mounting screw set (2 screws,2 stickers) 2
Extend interface relay board 1
Manuals
The following shows manuals relevant to this product.
For relevant manuals, refer to the PDF manuals stored in the DVD-ROM for the drawing
software used.
Detailed Manual
Manual name Manual number
(Model code)
GT15 User's Manual
(Sold separately)
SH-080528ENG
(1D7M23)
GOT1000 Series Connection Manual (Microcomputer,
MODBUS Products, Peripherals) for GT Works3
(Sold separately)
SH-080871ENG
(1D7MC5)
Relevant Manuals

1
1. OVERVIEW
This User's Manual is related to the following units.
• MODEL GT15V-75V4 Video Input Unit (hereinafter referred to as the Video
Input Unit)
• MODEL GT15V-75R1 RGB Input Unit (hereinafter referred to as the RGB
Input Unit)
• MODEL GT15V-75V4R1 Video/RGB Input Unit (hereinafter referred to as the
Video/RGB Input Module).
When mounting the above units with the GT1585V-STBA, GT1575V-STBA
(hereinafter referred to as GOT), the images taken by video cameras or screens
on personal computers can be displayed on the GOT.
The video input unit can display the images taken by up to 4 video cameras on
the GOT.
GOT can be used as a vision sensor monitor.
*1: Power on the video camera simultaneously with the GOT.
*2: Power supply for the camera may be necessary depending on the
vision sensor to be used.
Image data
GOT
+
GT15V-75V4
Camera power pack
*2
Video camera
*1
Video camera
Vision sensor (AS50VS or other)

2
The RGB input unit can display a personal computer display on the GOT.
Video input is also available using an RGB output type vision sensor.
*1: When connecting with a personal computer, ground wire of the
computer should be grounded.
For the video/RGB input unit, functions of both video input unit (GT15V-75V4) and
RGB input unit (GT15V-75R1) are available.
When connecting to a personal computer
GOT+GT15V-75R1
*1
When connecting to a video camera using an RGB output type vision sensor.
RGB output type
vision sensor
GOT+GT15V-75R1
A1254
348
B
GOT
*3
GT15V-75V4R1
Video camera
*2
Computer PLCs for line control
Don ot mount not desmount
amo dule while th e powe r is
supplied.
CAUTION
*1