
Leave a space of more than 2 cm to the left
and right, and more than 10 cm from the ceiling,
and more than 5 cm from the back.
This is to allow heat to escape from the top, the back and sides.
The outside of the unit will get hot.
When you first start running the unit, or in the summer, there
may be times when the temperature can go over 50 – 60 oC.
Leave a space around the unit for heat to escape
Corrosion control treatment may be required for the
refrigerant circuit (pipe) due to generation of corrosive gases.
Contact the retail store where you purchased the refrigerator.
Use in hot spring areas
Do not obstruct the refrigerator vents or the space
around the refrigerator. If refrigerant leaks,
it may accumulate and catch fire or explode.
Warning
From installing to running your refrigerator.
From installing to running your refrigerator.
Installation
10 cm. or more
2 cm. or more
Install in a place where there is no direct
sunlight or heat, and with good ventilation.
This protects against a decrease in cooling power and
saves on electricity bills.
Install in a place with low humidity.
This prevents rust, electric shock or fires from occurring.
Install on a solid and level floor.
This prevents vibrations, noise, and partially open doors
or doors left ajar.
If the refrigerator adjustment feet sink easily into the flooring
material, please lay a strong board on top of the flooring.
(Prevent changes or discoloring by its mass or heat.)
Install away from other appliances.
This prevents noise or image disturbances to the television, etc.
Where to Install your Fridge
Making Adjustments
and Affixing
Turn in the direction of the
arrows and lower the adjustable
legs to place on the floor.
Toe Grille Caster
Adjustable Leg
The Adjustable Leg Covers are packed in
together with the refrigerator for shipping.
Turn the adjustable legs to get
them to touch the floor and let
the front casters up, then affix.
Prevents vibration, noise, movement and the partial opening of doors.
Caution
If it is not done properly, the refrigerator may move and cause injury.
Make sure the left and right sides are level, and keep
the front at a slightly higher angle. This makes closing
the door easier and prevents the door from partially opening.
When the tilt cannot be corrected with the adjustable legs.
If installed in a corner of a room, there are
times when one side of the back legs sinks
into the floor. When that happens, please
make adjustments in the back with casters
(to be purchased) or lay a strong board
underneath. (Normally, the thickness of the
board should be 2 - 3 mm.)
About the direction of the door.
If the installation space is not level, or if after a few days, the
weight of the food causes the leg to sink, the door will look like
it is sagging. (There are times that the weight of food stored in
the refrigerator exceeds 100 kilograms.) Please adjust the adjustable
legs by turning them in the direction indicated in the diagram.
If the left side of
the door is sagging If the right side of
the door is sagging
Back legs
Adjustable legs
Raise the right side Raise the left side
Right Left
Electrical
Connections
To get the refrigerator
cooled down faster, plug
it in right after installing.
Lower back section
Earth screw connection
To prevent electric shock, installing
an earth wire is recommended.
Install an earth wire or an earth leakage
circuit breaker, especially when installing
takes place where there is a lot of dampness
(wooden floor, washing room, basement, etc.).
Use a dedicated outlet for the
power supply that meets the rating
specified on the rating label.
(The rating label is located on the
liner of the refrigerator compartment.)
Important: For personal safety, this
appliance must be properly grounded.
The refrigerator should always be plugged
into its own individual electrical outlet.
This is recommended for best performance
and also in order to prevent the overloading
of household wiring circuits, which may
cause a fire hazard.
Extension cords are not recommended.
Make sure that the outlet provides the
correct voltage.
Your refrigerator has a grounding plug,
use it correctly.
The 3-point plug must be inserted into
a mating 3-point grounded receptacle.
The ground point should never be cut or
removed.
Turn on the power of the refrigerator
as soon as possible.
The refrigerator will not be damaged even if you
turn on the power immediately after the installation.
How to remove the energy label
Remove the energy label carefully. A glue residue may remain, particularly
if the label has been in place for a long period of time.
Apply either Eucalyptus or Tea Tree oil directly on any residue.
Do not allow the oil to run or drip onto plastic parts as it may cause the
plastic to degrade and potentially crack over time.
Allow the oil to sit for approximately 1-2 minutes, or until the glue residue
has softened.
Wipe off with a damp cloth.
If any residue remains, repeat the above process.
Rinse with clear water.
Dry thoroughly.
Warning
Although R600a refrigerants are combustible,
the refrigerant circuit is hermetically
sealed and normally leaks will not occur.
Then, contact the retail store where you
purchased the refrigerator.
Shouldthe refrigerant circuit be damaged:
1.
Do not use flames or electrical appliances nearby.
2.
Open the windows to fully ventilate the room.
Do not damage the refrigerant
circuit (pipes) or drive screws into it.