Mitsubishi Electric DX-TL308E User manual

DIGITAL RECORDER
RS-232C COMMUNICATION CAPACITY
OPERATION MANUAL
MODEL
DX-TL308E series
DX-TL304E series
Contents
Disclaimer......................................................................................................2
Connecting to a personal computer ...........................................................2
Direct connection ....................................................................................................2
RS-232C connector..................................................................................................2
RS-232C cable.........................................................................................................2
About command code table.........................................................................3
Cautionary note on sending commands...................................................................3
RS-232C settings.....................................................................................................3
Command code system ...........................................................................................3
Description of command code systems ...................................................................3
Direct operation specification.............................................................................3
Quasi-front panel operation command type.......................................................4
Status condition change information function.....................................................4
Command receipt confirmation function.............................................................4
Command code table....................................................................................5
RS-232C [Direct operation specification] operation setting command form.............5
RS-232C [Direct operation specification] menu setting command form.................12
<Copy Menu>...................................................................................................12
<Search Menu>................................................................................................14
<Recording setting-Manual setting (Recording A)>..........................................15
<Recording setting-Manual setting (Recording B)>..........................................17
<Recording setting-Manual setting (Recording C)>..........................................19
<Recording setting-Manual setting (Recording D)>..........................................21
<Recording setting-EMR recording/Auto setting> ............................................23
<Recording setting-Motion detection setting/Audio recording settings>...........24
<Recording setting-Timer program>.................................................................25
<Recording setting-Protect recorded data>......................................................27
<HDD registration>...........................................................................................28
<Setup>............................................................................................................29
<Device selection> ...........................................................................................36
<Others>...........................................................................................................37
RS-232C [Direct operation specification] status check command form..................38
RS-232C [Quasi-front panel operation] command form.........................................40
RS-232C Status condition change notification.......................................................42

2
This recorder can be remotely controlled from a PC connected via a RS-232C connector.
Direct connection
Use a RS-232C crossover cable (9 pin) to connect this recorder with a personal computer. The pin layout of the RS-232C
connector varies depending on the personal computer connected. Check the pin layout and use the proper crossover
cable for the personal computer used.
This recorder
PC
RS-232C crossover cable (9 pin)
* The illustration shows an example of DX-TL308E series.
RS-232C connector
RS-232C
1
69
5
Pin No. Letters Transmission Contents Pin No. Letters Transmission Contents
2 RXD Receiving Data 6 DSR Data Set Ready
3 TXD Transmission Data 7 RTS Request To Send
4 DTR Data Terminal Ready 8 CTS Clear To Send
5 GND Signal Ground
RS-232C cable
Use the following RS-232C crossover cable when connecting the RS-232C connector of the personal computer and that
of this recorder.
FRAME
D-sub 9 pin (this recorder) D-sub 25 pin (Personal computer)
FG
TXD
RXD
RTS
CTS
DSR
GND
DTR
1
2
3
4
5
6
7
20
RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
1) When RS-232C connector of personal
computer is D-sub 25 pin
D-sub 9 pin D-sub 9 pin
FRAMEFRAME RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
2) When RS-232C connector of personal
computer is D-sub 9 pin
Connecting to a personal computer
Disclaimer
In no event will Mitsubishi assume responsibility or liability for the following:
• Failure caused by any program created based on the command data provided by Mitsubishi, or inconvenience,
damages, or losses resulting from such failure.
• Inconvenience, damages, or losses caused by the mistake of the description in this operation manual.
Design and specifications are subject to change without notice.

3
Cautionary note on sending commands
After sending the command, make sure to check the operation of the recorder or the response such as an error before
sending the next command. Some commands such as search and copy take time to respond, therefore, test the
command operation sufficiently before the actual operation.
RS-232C settings
Settings related to communication of this recorder are made in the <Setup Menu> <Communication setting> <RS-
232C setting>. Make the same settings as the PC connected.
When remotely controlling this recorder from a PC, set “RS-232C operation” in the <RS-232C setting> to “Remote
A,” “Remote B,” or “Remote C.”
“Remote A” : The recorder returns all types of operation status notification.
“Remote B” : The recorder only responses to the command codes.
“Remote C” : The recorder does not return any notification.
Available settings on the recorder Make the following settings on the PC
Synchronization Name on
menu Asynchronous Synchronization Screen
display
1 Transmission rate for
receiving/sending data Transmission rate 1200 bps/2400 bps/
4800 bps/9600 bps/19200 bps
1 X control Not available
2 Data bit length Data bit length 8 bits/7 bits 2 S parameter Not available
3 Parity bit setting Parity bit None/Odd/Even 3 CS-RS hand-shake Available
4 Stop bit length Stop bit length 1 bit/2 bits
5 Line feed setting Delimiter CR/CR•LF
Command code system
2 types of command codes of [direct operation specification] and [quasi-front panel operation] can be selected according
to the purpose of the recorder operation.
Description of command code systems
Direct operation specification
This system controls or sets the recorder by confirming the status from the recorder such as execution and error which
are responded to the command from the personal computer. This command type is constructed by the “operation setting
commands” which sets operations, “menu setting commands” which directly sets various menus, and “status check com-
mands” which checks the operational status of the recorder.
• Input format
In case of “operation setting commands” and “status check commands,” send the command to the recorder for each op-
eration such as power on/off, record, playback, etc.
In case of “menu setting commands,” specify the setting item for each menu setting of the recorder.
As a general rule, do not send commands continuously, but send the next command after checking that the present com-
mand has been executed and completed.
• Response format
After sending a command, the following items can be checked by the status returned from the recorder.
1) Command execution result, error type, command name, and operation status.
2) For operation setting commands, the operational mode of the recorder can be distinguished by the mode number
of the returned status.
Distinction cannot be made for menu setting type commands. (Mode number is notified only when the status is
changed.)
Example) Turning on the power of the Recorder.
Command from PC Replied status code from
recorder to PC Meaning
PW1 ≤Indicates POWER ON command has been sent.
RC ≥Indicates that the recorder has received a command.
EX,00PW1,10 ≥EX : Indicates that a command has been executed.
00 : Indicates that the execution was successful. (Error type)
PW1 : Indicates response to POWER ON command.
10 : Indicates POWER ON status.
When the recorder cannot execute the operation setting command or menu setting command sent from a PC,
the error type which shows the content of the error is returned from the recorder. Check the error code and take
appropriate measures.
For operation setting commands such as recording and playback, the actual operation (command execution) may
take some time after transmitting the command. To prevent the gap between operation and actual execution, read
the status after sending the command and check the actual operational transition, and then send the next command.
While displaying the menu screen, you cannot change the menu setting by using menu setting command form.
About command code table

4
Quasi-front panel operation command type
This system specifies operations from a PC as if operating the actual operation panel of the recorder while viewing the
output picture. Each command is corresponded to the operation button of the recorder.
• Input confirmation format
Send commands as if operate the buttons on the operation panel. As a general rule, do not send commands continuously,
but send the next command after checking that the present command has been executed and completed. After sending
a command, the command execution result, error type, and command name can be checked by the status returned from
the recorder. To check the actual execution, view the output screen of the recorder on the monitor screen.
Example) Playing back the recorded data in still frame playback.
Command from PC Replied status code from
recorder to PC Meaning
KKP0 ≤Indicates that a command equivalent to “press the POWER button”
was sent.
RC ≥Indicates that the recorder has received a command.
EX,00KKP0 ≥EX : Indicates that a command has been executed.
00 : Indicates that the execution was successful. (Error type)
KKP0 : Indicates that the POWER button was operated.
KKB1 ≤Indicates that a command equivalent to “press the PLAY button”
was sent.
RC ≥Indicates that the recorder has received a command.
EX,00KKB1 ≥EX : Indicates that a command has been executed.
00 : Indicates that the execution was successful. (Error type)
KKB1 : Indicates that the PLAY button was operated.
KKB4 ≤Indicates that a command equivalent to “press the PAUSE button”
was sent.
RC ≥Indicates that the recorder has received a command.
EX,00KKB4 ≥EX : Indicates that a command has been executed.
00 : Indicates that the execution was successful. (Error type)
KKB4 : Indicates that the PAUSE button was operated.
For control type commands such as recording and playback, the actual operation (command execution) may take
some time after transmitting the command.
To prevent the gap between operation and actual execution, read the
status after sending the command and check the actual operational transition, and then send the next command.
Status condition change information function
Example) Notifying the status of the fan (stop of the fan).
Replied status code from
recorder to PC Meaning
NTFY04,00080321140000
192168000100 ≥NTFY :Indicates the status condition change notification. 04 :Indicates the status of the fan.
00 :Indicates that the fan is stopped.
080321140000 :Indicates the occurred time and date (year/month/day/hour/minute/
second).
192168000100 :Indicates the IP address of the recorder.
When you set “RS-232C operation” in the <RS-232C setting> to “Remote A,” the recorder returns all types of operation
status notification. When “Remote B” is set, the recorder only responses to the command codes. When “Remote C” is
set, the recorder does not return any notification.
Command receipt confirmation function
After executing a received command, the error type for command execution is notified after the execution status, “EX.”
Error type Error description
00 Normal
01 Execution Error
02 Execution Unable Error
03 Incorrect command
04 Incorrect parameter
05 Executing the command
06 Not corresponding
About command code table (continued)

5
Detail of the numbers:
≤ : When “Delimiter” in the <RS-232C setting> is set to “CR,” carriage return code (0DH) is input. When “Delimiter” is
set to “CR•LF,” carriage return code (0DH) and line feed code (0AH) are input.
≥ : When “Delimiter” in the <RS-232C setting> is set to “CR,” carriage return code (0DH) is output. When “Delimiter” is
set to “CR•LF,” carriage return code (0DH) and line feed code (0AH) are output.
*: Indicates one number or character.
RS-232C [Direct operation specification] operation setting command form (1/7)
Command name Command Status Note
Power PW*(1) ≤RC ≥
EX,**(2)PW*(1),**(3) ≥
*(1):Power on/off
0:Off 1:On
**(2):Error type (Refer to page 4.)
**(3):System mode number
00:Power off
01:Transition to power-off
10:Power on
11:Booting-up
Record RC*(1) ≤RC ≥
EX,**(2)RC*(1),**(3) ≥
*(1):Recording/Stop of recording
0:Stop 1:Recording
**(2):Error type (Refer to page 4.)
**(3):Recording mode number
00:Stop of recording
01:Waiting for stopping
02:Execution (Recording)
03:Waiting for carrying out recording
Playback PB00,**(1)**(2)**(3) ≤RC ≥
EX,**(4)PB00,**(1)**(2)
**(3),**(5)**(6) ≥
**(1):Output port of playback picture
00:Output A
**(2):Playback command
00:Stop 01:Pause
02:Playback 03:
Frame-by-frame playback
04:Fast forward 1 05:Fast forward 2
06:Fast forward 3 07:Fast forward 4
08:High-speed fast forward
**(3):Playback direction
00:Forward 01:Reverse
**(4):Error type (Refer to page 4.)
**(5):Playback mode number
00:Stop of playback 01:Forward playback
02:Reverse playback
03:Pause of forward playback
04:Pause of reverse playback
05:Forward search 06:Reverse search
07:High speed forward search
08:High speed reverse search
09:Waiting for start 10:Waiting for stop
**(6):Display mode number
11:Single 12:Split 13:Enlarged
Acquire information
of recording start/
end point
IF00,**(1)**(2)**(3) ≤RC ≥
EX,**(4)IF00,**(1)**(2)
**(3),**(5)**(6)**(7)
**(8)**(9)**(10)**(11)
**(12)**(13)**(14)**(15)
**(16) ≥
**(1):Device including the data to be acquired
01:Main 02:Copy 03:Archive
**(2):Group including the data to be acquired
<For Main>
01:Normal 02:Alarm
03:Emergency 04:Preliminary
<For Copy>
00:SerialBus 03:DVD/CD 04:USB memory
<For Archive>
00:SerialBus
**(3):Output port
00:Output A
**(4):Error type (Refer to page 4.)
**(5):Start year (01-37) **(6):Start month (01-12)
**(7):Start day (01-31) **(8):Start hour (00-23)
**(9):Start minute (00-59) **(10):Start second (00-59)
**(11):End year (01-37) **(12):End month (01-12)
**(13):End day (01-31) **(14):End hour (00-23)
**(15):End minute (00-59) **(16):End second (00-59)
Command code table

6
RS-232C [Direct operation specification] operation setting command form (2/7)
*: The commands marked with asterisk (*) are not available with DX-TL304E series.
Command name Command Status Note
Display SW,**(1)****(2) ≤RC≥
EX,**(3)SW,**(1)
****(2),**(4)**(5) ≥
**(1):Output port
00:Output A 01:Output B
****(2):Switcher command
0100:Single screen sequential
0101:CH1 0102:CH2 0103:CH3
0104:CH4 0105:CH5* 0106:CH6*
0107:CH7* 0108:CH8*
0180:Zoom cancel 0181:Zoom (X 1)
0182:Zoom (X 2) 0184:Zoom (X 4)
0191:Zoom (move upward)
0192:Zoom (move downward)
0193:Zoom (move rightward)
0194:Zoom (move leftward)
0400:Split 4 sequential*
0401:4a (for DX-TL304E series, Split 4)
0402:4b* 0901: Split 9*
**(3):Error type (Refer to page 4.)
**(4):Playback mode number
For playback mode number, refer to Playback
command.
**(5):Display mode number
11:Single 12:Split 13:Enlarged
Timer TM*(1) ≤RC ≥
EX,**(2)TM*(1),**(3) ≥
*(1):Timer On/Off
0:Timer Off 1:Timer On
**(2):Error type (Refer to page 4.)
**(3):Timer mode number
00:Timer Off 01:Timer On 02:Timer error
Prevent alarm input AD*(1) ≤RC ≥
EX,**(2)AD*(1),**(3) ≥
*(1):Alarm input prevention
0:Alarm input enabled
1:Alarm input disabled
**(2):Error type (Refer to page 4.)
**(3):Alarm input prevention mode number
00:Alarm input enabled
01:Alarm input disabled
PTZ control PTZ,**(1)**(2) ≤RC ≥
EX,**(3)PTZ,**(1)**(2)
≥
**(1):PTZ command number
10:Pan - Right 14:Pan - Left
18:Tilt - Up 1C:Tilt - Down
20:Zoom - Tele 24:Zoom - Wide
28:Focus - Near 2C:Focus - Far
30:Iris - Open 34:Iris - Close
38:Stop
40-4F:Memorize preset 1-16
50-5F:Move to preset 1-16
C0-CF:Memorize preset 17-32
D0-DF:Move to preset 17-32
E0-EF:Memorize preset 33-48
F0-FF:Move to preset 33-48
**(2):Camera number
00:CH1 01:CH2 02:CH3
03:CH4 04:CH5* 05:CH6*
06:CH7* 07:CH8*
**(3):Error type (Refer to page 4.)
Command code table (continued)

7
RS-232C [Direct operation specification] operation setting command form (3/7)
Command name Command Status Note
Start copy
(Archive supported) CP6,**(1)**(2)**(3)
**(4)**(8)**(9) ≤
RC ≥
EX,**(5)CP6,**(1)
**(2)**(3)**(4)**(8)**(9),
**(6)**(7) ≥
**(1):Copy destination device
02:Copy 03:Archive
10:
Copy according to the calculation result of the copy range
**(2):Copy destination group
<For Copy>
00:SerialBus 03:DVD/CD 04:USB memory
<For Archive>
00:SerialBus
**(3):Copy source device
01:Main 03:Archive
**(4):Copy source area
<For Main>
01:Normal 02:Alarm 03:Emergency
<For Archive>
00:SerialBus (Available only when the copy
destination device is set to "02:Copy" or "10:Copy
according to the calculation result of the copy range".)
**(5):Error type (Refer to page 4.)
**(6):Copy mode number
00:Stop 02:Execute 04:Copy error
**(7):Data error type
00:No error 10:No device 11:No media
20:No data 30:Improper range
32:Size error 99:Other errors
**(8):Copy range set method
00:Specify start and end times
01:Specify start time and capacity
02:Start time of archive
**(9):
<For Copy>
00:Fixed
<For Archive>
00:Archive from the start point of recording
01:Archive from the end point of previous archive
Stop copy CP0,**(1) ≤RC ≥
EX,**(2)CP0,**(1),
**(3) ≥
**(1):Copy device
02:Copy 03:Archive
**(2):Error type (Refer to page 4.)
**(3):Copy mode number
00:Stop 02:Execute 04:Copy error
Command code table (continued)

8
RS-232C [Direct operation specification] operation setting command form (4/7)
Command name Command Status Note
Clear warning
display WC*(1) ≤RC ≥ EX,**(2)WC*(1),
**(3) ≥
*(1):Clearing warning display command
0:Clear
**(2):Error type (Refer to page 4.)
**(3):System mode number (Refer to Power command)
Load/save menu data MC,*(1)**(2)**(3) ≤RC ≥
EX,**(4)MC,*(1)**(2)
**(3),**(5)**(6) ≥
*(1):Menu loading/saving command
1:Load 2:Save
**(2):Device to be loaded/saved
02:Copy 04:Internal memory
**(3):Device group to be loaded/saved
<For Copy>
03:DVD/CD 04:USB memory
<For Internal memory>
06:Inernal memory
**(4):Error type (Refer to page 4.)
**(5):Data error type
00:No error 10:No device 11:No medium
20:No data 21:Improper data
22:Unavailable data (Unconformable partition setting)
**(6):System mode number (Refer to Power command)
Initialize menu MC,00100 ≤RC ≥
EX,**(1)MC,00100,
**(2) ≥
**(1):Error type (Refer to page 4.)
**(2):System mode number (Refer to Power command)
Clear data CL,**(1)**(2) ≤RC ≥
EX,**(3)CL,**(1)**(2),
**(4) ≥
**(1):Device including the data to be cleared
01:Main 02:Copy 03:Archive
**(2):Device group including the data to be cleared
<For Main>
01:Normal 02:Alarm 03:Emergency
<For Copy>
00:SerialBus 03:DVD/CD 04:USB memory
<For Archive>
00:SerialBus
**(3):Error type (Refer to page 4.)
**(4):Data clearing mode number
00:End 02:Data clearing error
Construct alarm list IFC01,**(1)**(2)**(3)
****(4)****(5)**(6)
**(7)**(8)**(9)**(10)
**(11) ≤
RC ≥
EX,**(12)IFC01,**(1)
**(2)**(3)****(4)
****(5)**(6)**(7)
**(8)**(9)**(10)
**(11),****(13) ≥
**(1):Alarm list construction device
01:Main 02:Copy 03:Archive
**(2):Alarm list construction device group
<For Main>
01:Normal 02:Alarm 03:Emergency
<For Copy>
00:SerialBus 03:DVD/CD 04:USB memory
<For Archive>
00:SerialBus
**(3):Direction
00:Forward direction from specified time
01:Reverse direction from specified time
02:
Forward direction from end point of previous construction
03: Reverse direction from start point of previous construction
04:Starts construction from start point of the specified
device (forward direction)
05:Starts construction from end point of the specified
device (reverse direction)
****(4):The number of list items
0000-1000
****(5):Sensor to be searched
Shown using hexadecimal number. Bit allocation for
each sensor
LSB=sensor 1 Ex. "003F" indicates sensor numbers 1 to 6.
**(6):Specified time/year (01-37)
**(7):Specified time/month (01-12)
**(8):Specified time/day (01-31)
**(9):Specified time/hour (00-23)
**(10):Specified time/minute (00-59)
**(11):Specified time/second (00-59)
**(12):Error type (Refer to page 4.)
****(13):The number of items to be constructed
0000-1000
Command code table (continued)

9
RS-232C [Direct operation specification] operation setting command form (5/7)
*: The commands marked with asterisk (*) are not available with DX-TL304E series.
Command name Command Status Note
Execute data lock DLOKS,**(1)**(2)
**(3) ≤
RC ≥
EX,**(4)DLOKS,**(1)
**(2)**(3),**(5) ≥
**(1):Device area including the data to be locked
01:Normal 02:Alarm 03:Emergency
**(2):Bookmark number of start point
00:1 01:2 02:3
03:4 04:5 05:6
06:7 07:8
**(3):Bookmark number of end point
00:1 01:2 02:3
03:4 04:5 05:6
06:7 07:8
**(4):Error type (Refer to page 4.)
**(5):Data error type
00:No error 20:No data 22:Already locked
30:Improper range
31:Excess of available number 99:Other errors
Construct data lock
list IFC03,**(1) ≤RC ≥
EX,**(2)IFC03,**(1),
*****(3) ≥
**(1):Device area for constructing data lock list
01:Normal 02:Alarm 03:Emergency
**(2):Error type (Refer to page 4.)
*****(3):The number of items to be constructed
Switching audio AUDIOO,**(1)**(2) ≤RC ≥
EX,**(3)AUDIOO,**(1)
**(2) ≥
**(1):Output terminal
00:Audio output
**(2):Switching audio
00:Audio input 90:Mute
**(3):Error type (Refer to page 4.)
Total operating time ELPQ,**(1)****(2) ≤RC ≥
EX,**(3)ELPQ,**(1)
****(2),*****(4) ≥
**(1):Device to be acquired
00:System 01:Main 02:Copy
03:Archive
****(2):Device group to be acquired
0000-0003:Internal HDD
0100-0107:External HDD
0200:DVD/CD
0300:USB memory
**(3):Error type (Refer to page 4.)
*****(4):Total operating time
00000-99999 (hour)
Alarm recording of
specified camera RCCA,**(1) ≤RC ≥
EX,**(2)RCCA,**(1) ,
**(3) ≥
**(1):Camera number
00:CH1 01:CH2 02:CH3
03:CH4 04:CH5* 05:CH6*
06:CH7* 07:CH8*
**(2):Error type (Refer to page 4.)
**(3):Recording mode number
00:Stop of recording
01:Waiting for stopping
02:Recording
03:Waiting for carrying out recording
Command code table (continued)

10
RS-232C [Direct operation specification] operation setting command form (6/7)
*: The commands marked with asterisk (*) are not available with DX-TL304E series.
Command name Command Status Note
Search device
selection PDV,**(1)**(2)**(3) ≤RC ≥ EX,**(4)PDV,**(1)**(2)
**(3) ≥
**(1):Output port of playback picture
00:Output A
**(2):Playback device
01:Main 02:Copy 03:Archive
**(3):Playback device group
<For Main>
01:Normal 02:Alarm 03:Emergency
<For Copy>
00:SerialBus 03:DVD/CD 04:USB memory
<For Archive>
00:SerialBus
**(4):Error type (Refer to page 4.)
Time date search PB10,**(1)**(2)**(3)
**(4)**(5)**(6)**(7)**(10)
≤
RC ≥
EX,**(8)PB10,**(1)
**(2)**(3)**(4)**(5)**(6)
**(7)**(10),**(9) ≥
**(1):Output port of playback picture
00:Output A
**(2):Time to be searched/year (01-37)
**(3):Time to be searched/month (01-12)
**(4):Time to be searched/day (01-31)
**(5):Time to be searched/hour (00-23)
**(6):Time to be searched/minute (00-59)
**(7):Time to be searched/second (00-59)
**(8):Error type (Refer to page 4.)
**(9):
Playback mode number (Refer to Playback command)
**(10):
<For DX-TL308E series>
00-07: Camera 1-8
20: All cameras
<For DX-TL304E series>
00-03: Camera 1-4
20: All cameras
Start point search PB11,**(1) ≤RC ≥
EX,**(2)PB11,
**(1),**(3) ≥
**(1):Output port of playback picture
00:Output A
**(2):Error type (Refer to page 4.)
**(3):
Playback mode number (Refer to Playback command)
End point search PB12,**(1) ≤RC ≥
EX,**(2)PB12,
**(1),**(3) ≥
**(1):Output port of playback picture
00:Output A
**(2):Error type (Refer to page 4.)
**(3):
Playback mode number (Refer to Playback command)
Acquire alarm list
information LSTI01,****(1) ≤RC ≥
EX,**(2)LSTI01,
****(1),**(3)**(4)
**(5)**(6)**(7)**(8)
**(9)**(10) ≥
****(1):Alarm list number
0000-0999
**(2):Error type (Refer to page 4.)
**(3):Time of alarm/year (01-37)
**(4):Time of alarm/month (01-12)
**(5):Time of alarm/day (01-31)
**(6):Time of alarm/hour (00-23)
**(7):Time of alarm/minute (00-59)
**(8):Time of alarm/second (00-59)
**(9):Sensor number
00:Sensor 1 01:Sensor 2 02:Sensor 3
03:Sensor 4 04:Sensor 5* 05:Sensor 6*
06:Sensor 7* 07:Sensor 8*
**(10):Factor of starting recording
00:Motion detection
02:Rear terminal (ALARM IN terminal)
03:Rear terminal (EMERGENCY terminal)
04:Communication
Alarm list search PBC01,**(1)
****(2) ≤
RC ≥
EX,**(3)PBC01,**(1)
****(2) ≥
**(1):Output port of playback picture
00:Output A
****(2):List number to be searched
0000-0999
**(3):Error type (Refer to page 4.)
Command code table (continued)

11
RS-232C [Direct operation specification] operation setting command form (7/7)
Command name Command Status Note
Bookmark search PB21,**(1)**(2) ≤RC ≥
EX,**(3)PB21,**(1)
**(2),**(4) ≥
**(1):Output port of playback picture
00:Output A
**(2):Bookmark number to be searched
00:1 01:2 02:3
03:4 04:5 05:6
06:7 07:8
**(3):Error type (Refer to page 4.)
**(4):
Playback mode number (Refer to Playback command)
Acquire data lock list
information LSTI03,****(1) ≤RC ≥ EX,**(2)LSTI03,
****(1),**(3)**(4)
**(5)**(6)**(7)**(8)
**(9)**(10)**(11)**(12)
**(13)**(14) ≥
****(1):List number to be acquired
0000-0999
**(2):Error type (Refer to page 4.)
**(3):Start year (01-37)
**(4):Start month (01-12)
**(5):Start day (01-31)
**(6):Start hour (00-23)
**(7):Start minute (00-59)
**(8):Start second (00-59)
**(9):End year (01-37)
**(10):End month (01-12)
**(11):End day (01-31)
**(12):End hour (00-23)
**(13):End minute (00-59)
**(14):End second (00-59)
Data lock search PBC03,**(1)****(2) ≤RC ≥
EX,**(3)PBC03,**(1)
****(2) ≥
**(1):Output port of playback picture
00:Output A
****(2):List number to be searched
0000-4095
**(3):Error type (Refer to page 4.)
Command code table (continued)

12
RS-232C [Direct operation specification] menu setting command form <Copy Menu> (1/3)
*: The commands marked with asterisk (*) are not available with DX-TL304E series.
Menu Menu item Command Status Note
Set the copy
conditions Copy from
<Menu setting>
DW,*****
(1)
*****
(2)
≤
<Inquiry for
setting information>
DR,*****
(1)
≤
<Writing of menu information>
RC ≥EX,**(3)DW,***
**(1)*****(2) ≥
<Reading of menu information>
RC ≥EX,**(3)DR,
*****(1),*****(2) ≥
*****(1):01000
*****(2):
00000:HDD (Normal)
00001:HDD (Alarm)
00002:HDD (Emergency)
00004:HDD (Archive)
**(3):Error type (Refer to page 4.)
Copy to ÷ ÷ *****(1):01001
*****(2):
00003:HDD (Copy) 00010:DVD/CD
00011:USB memory
**(3):Error type (Refer to page 4.)
Camera and
audio filter ÷ ÷ *****(1):
01010:
Camera 1 01011: Camera 2 01012: Camera 3
01013:
Camera 4 01014: Camera 5* 01015: Camera 6*
01016: Camera 7* 01017: Camera 8* 01026:Audio
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
Copied data ÷ ÷ *****(1):01028
*****(2):
00000:All 00001:Alarm
**(3):Error type (Refer to page 4.)
Auto eject ÷ ÷ *****(1):01029
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
Set the start
and end points Start point/year ÷ ÷ *****(1):01050
*****(2):00001-00037 (year 2001-2037)
**(3):Error type (Refer to page 4.)
Start point/month ÷ ÷ *****(1):01051
*****(2):00001-00012 (January-December)
**(3):Error type (Refer to page 4.)
Start point/day ÷ ÷ *****(1):01052
*****(2):00001-00031 (1st-31st)
**(3):Error type (Refer to page 4.)
Start point/hour ÷ ÷ *****(1):01053
*****(2):00000-00023 (hour 0-23)
**(3):Error type (Refer to page 4.)
Start point/
minute ÷ ÷ *****(1):01054
*****(2):00000-00059 (minute 0-59)
**(3):Error type (Refer to page 4.)
Start point/
second ÷ ÷ *****(1):01055
*****(2):00000-00059 (second 0-59)
**(3):Error type (Refer to page 4.)
End point/year ÷ ÷ *****(1):01056
*****(2):00001-00037 (year 2001-2037)
**(3):Error type (Refer to page 4.)
End point/month ÷ ÷ *****(1):01057
*****(2):00001-00012 (January-December)
**(3):Error type (Refer to page 4.)
End point/day ÷ ÷ *****(1):01058
*****(2):00001-00031 (1st-31st)
**(3):Error type (Refer to page 4.)
End point/hour ÷ ÷ *****(1):01059
*****(2):00000-00023 (hour 0-23)
**(3):Error type (Refer to page 4.)
End point/minute ÷ ÷ *****(1):01060
*****(2):00000-00059 (minute 0-59)
**(3):Error type (Refer to page 4.)
End point/
second ÷ ÷ *****(1):01061
*****(2):00000-00059 (second 0-59)
**(3):Error type (Refer to page 4.)
Command code table (continued)

13
RS-232C [Direct operation specification] menu setting command form <Copy Menu> (2/3)
Menu Menu item Command Status Note
Set the start
point and
capacity
Start point/year
<Menu setting>
DW,*****
(1)
*****
(2)
≤
<Inquiry for
setting information>
DR,*****
(1)
≤
<Writing of menu information>
RC ≥EX,**(3)DW,***
**(1)*****(2) ≥
<Reading of menu information>
RC ≥EX,**(3)DR,
*****(1),*****(2) ≥
*****(1):01070
*****(2):00001-00037 (year 2001-2037)
**(3):Error type (Refer to page 4.)
Start point/month ÷ ÷ *****(1):01071
*****(2):00001-00012 (January-December)
**(3):Error type (Refer to page 4.)
Start point/day ÷ ÷ *****(1):01072
*****(2):00001-00031 (1st-31st)
**(3):Error type (Refer to page 4.)
Start point/hour ÷ ÷ *****(1):01073
*****(2):00000-00023 (hour 0-23)
**(3):Error type (Refer to page 4.)
Start point/
minute ÷ ÷ *****(1):01074
*****(2):00000-00059 (minute 0-59)
**(3):Error type (Refer to page 4.)
Start point/
second ÷ ÷ *****(1):01075
*****(2):00000-00059 (second 0-59)
**(3):Error type (Refer to page 4.)
Set the capacity/
Capacity (value) ÷ ÷ *****(1):01076
*****(2):00001-00999 (1-999)
(2 MB-999 MB, 1 GB-100 GB)
**(3):Error type (Refer to page 4.)
Set the capacity/
Capacity (unit) ÷ ÷ *****(1):01077
*****(2):
00000:MB 00001:GB
**(3):Error type (Refer to page 4.)
Set the capacity/
Capacity or
media full
÷ ÷ *****(1):01079
*****(2):
00000:Capacity
00001:Media full (Available only when the copy
destination device is DVD/CD)
**(3):Error type (Refer to page 4.)
Set the end
point and
capacity
End point/year ÷ ÷ *****(1):01090
*****(2):00001-00037 (year 2001-2037)
**(3):Error type (Refer to page 4.)
End point/month ÷ ÷ *****(1):01091
*****(2):00001-00012 (January-December)
**(3):Error type (Refer to page 4.)
End point/day ÷ ÷ *****(1):01092
*****(2):00001-00031 (1st-31st)
**(3):Error type (Refer to page 4.)
End point/hour ÷ ÷ *****(1):01093
*****(2):00000-00023 (hour 0-23)
**(3):Error type (Refer to page 4.)
End point/minute ÷ ÷ *****(1):01094
*****(2):00000-00059 (minute 0-59)
**(3):Error type (Refer to page 4.)
End point/
second ÷ ÷ *****(1):01095
*****(2):00000-00059 (second 0-59)
**(3):Error type (Refer to page 4.)
Set the capacity/
Value ÷ ÷ *****(1):01096
*****(2):00001-00010 (1-10)
**(3):Error type (Refer to page 4.)
Set the capacity/
Unit ÷ ÷ *****(1):01097
*****(2):
00001:GB
**(3):Error type (Refer to page 4.)
Command code table (continued)

14
Command code table (continued)
RS-232C [Direct operation specification] menu setting command form <Copy Menu> (3/3)
*: The commands marked with asterisk (*) are not available with DX-TL304E series.
Menu Menu item Command Status Note
Define the
archiving
conditions
Start
<Menu setting>
DW,*****
(1)
*****
(2)
≤
<Inquiry for
setting information>
DR,*****
(1)
≤
<Writing of menu information>
RC ≥EX,**(3)DW,***
**(1)*****(2) ≥
<Reading of menu information>
RC ≥EX,**(3)DR,
*****(1),*****(2) ≥
*****(1):12038
*****(2):
00000:Read start time
00001:Read previous end point
**(3):Error type (Refer to page 4.)
Archive from ÷ ÷ *****(1):01100
*****(2):
00000:HDD (Normal)
00001:HDD (Alarm)
00002:HDD (Emergency)
**(3):Error type (Refer to page 4.)
Camera and
audio filter ÷ ÷ *****(1):
01109:
Camera 1 01110: Camera 2 01111: Camera 3
01112:
Camera 4 01113: Camera 5* 01114: Camera 6*
01115: Camera 7* 01116: Camera 8* 01125:Audio
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
FIFO overwrite ÷ ÷ *****(1):01127
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
Start point/year ÷ ÷ *****(1):01140
*****(2):00001-00037 (year 2001-2037)
**(3):Error type (Refer to page 4.)
Start point/month ÷ ÷ *****(1):01141
*****(2):00001-00012 (January-December)
**(3):Error type (Refer to page 4.)
Start point/day ÷ ÷ *****(1):01142
*****(2):00001-00031 (1st-31st)
**(3):Error type (Refer to page 4.)
Start point/hour ÷ ÷ *****(1):01143
*****(2):00000-00023 (hour 0-23)
**(3):Error type (Refer to page 4.)
Start point/
minute ÷ ÷ *****(1):01144
*****(2):00000-00059 (minute 0-59)
**(3):Error type (Refer to page 4.)
Start point/
second ÷ ÷ *****(1):01145
*****(2):00000-00059 (second 0-59)
**(3):Error type (Refer to page 4.)
One touch
copy Copied data ÷ ÷ *****(1):01240
*****(2):
00000:Moving image 00001:Still image
**(3):Error type (Refer to page 4.)
Duration ÷ ÷ *****(1):01241
*****(2):00001-00015 (1 minute-15 minutes)
**(3):Error type (Refer to page 4.)
RS-232C [Direct operation specification] menu setting command form <Search Menu>
Menu Menu item Command Status Note
Copy
conditions Copy to
<Menu setting>
DW,*****
(1)
*****
(2)
≤
<Inquiry for
setting information>
DR,*****
(1)
≤
<Writing of menu information>
RC ≥EX,**(3)DW,***
**(1)*****(2) ≥
<Reading of menu information>
RC ≥EX,**(3)DR,
*****(1),*****(2) ≥
*****(1):01250
*****(2):
00003:HDD (Copy) 00010:DVD/CD
00011:USB memory
**(3):Error type (Refer to page 4.)
Auto eject ÷ ÷ *****(1):01251
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)

15
Command code table (continued)
RS-232C [Direct operation specification] menu setting command form <Recording setting-Manual
setting (Recording A)> (1/2)
*: The commands marked with asterisk (*) are not available with DX-TL304E series.
Menu Menu item Command Status Note
Manual setting (Recording A)
Picture size Picture size <Menu setting>
DW,*****
(1)
*****
(2)
≤
<Inquiry for
setting information>
DR,*****
(1)
≤
<Writing of menu information>
RC≥EX,**(3)DW,***
**(1)*****(2) ≥
<Reading of menu information>
RC≥EX,**(3)DR,
*****(1),*****(2) ≥
*****(1):02000
*****(2):
00000:4CIF 00001:2CIF
00002:CIF
**(3):Error type (Refer to page 4.)
Long recording
mode ÷ ÷ *****(1):12043
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
Motion detection
recording ÷ ÷ *****(1):02001
*****(2):
00000:Normal recording 00001:Alarm recording
**(3):Error type (Refer to page 4.)
Alarm recording/
Pre-alarm time ÷ ÷ *****(1):02005
*****(2):00000-01800 (0 second-30 minutes)
**(3):Error type (Refer to page 4.)
Alarm recording/
Post-alarm time ÷ ÷ *****(1):02006
*****(2):
00000:Manual
00002-03600 (2 seconds-60 minutes)
**(3):Error type (Refer to page 4.)
Picture
quality and
FPS
Active ÷ ÷ *****(1):
02010:CH1 02011:CH2 02012:CH3
02013:CH4 02014:CH5* 02015:CH6*
02016:CH7* 02017:CH8*
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
Normal
recording/Quality ÷ ÷ *****(1):
02030:CH1 02031:CH2 02032:CH3
02033:CH4 02034:CH5* 02035:CH6*
02036:CH7* 02037:CH8*
*****(2):
00001:L1 00002:L2 00003:L3
00004:L4 00005:L5 00006:L6
00007:L7 00008:L8 00009:L9
**(3):Error type (Refer to page 4.)
Normal
recording/FPS ÷ ÷ *****(1):
02050:CH1 02051:CH2 02052:CH3
02053:CH4 02054:CH5* 02055:CH6*
02056:CH7* 02057:CH8*
*****(2):
00002:25 FPS 00004:12.5 FPS 00008:6.25 FPS
00016:3 FPS 00032:1.5 FPS 00064:0.8 FPS
00128:0.4 FPS 00256:0.2 FPS 65535:- - -
**(3):Error type (Refer to page 4.)
Alarm recording/
Quality ÷ ÷ *****(1):
02070:CH1 02071:CH2 02072:CH3
02073:CH4 02074:CH5* 02075:CH6*
02076:CH7* 02077:CH8*
*****(2):
00001:L1 00002:L2 00003:L3
00004:L4 00005:L5 00006:L6
00007:L7 00008:L8 00009:L9
**(3):Error type (Refer to page 4.)
Alarm recording/
FPS ÷ ÷ *****(1):
02090:CH1 02091:CH2 02092:CH3
02093:CH4 02094:CH5* 02095:CH6*
02096:CH7* 02097:CH8*
*****(2):
00002:25 FPS 00004:12.5 FPS 00008:6.25 FPS
00016:3 FPS 00032:1.5 FPS 00064:0.8 FPS
00128:0.4 FPS 00256:0.2 FPS 65535:- - -
**(3):Error type (Refer to page 4.)

16
Command code table (continued)
RS-232C [Direct operation specification] menu setting command form <Recording setting-Manual
setting (Recording A)> (2/2)
*: The commands marked with asterisk (*) are not available with DX-TL304E series.
Menu Menu item Command Status Note
Manual setting (Recording A) (continued)
Alarm
camera
setting
Recording
camera
<Menu setting>
DW,*****
(1)
*****
(2)
≤
<Inquiry for
setting information>
DR,*****
(1)
≤
<Writing of menu information>
RC≥EX,**(3)DW,***
**(1)*****(2) ≥
<Reading of menu information>
RC≥EX,**(3)DR,
*****(1),*****(2) ≥
*****(1):
(For DX-TL304E series, commands of CH 5 to 8 are not available.)
02110-02117:sensor number 1/camera number CH1-CH8
02130-02137:sensor number 2/camera number CH1-CH8
02150-02157:sensor number 3/camera number CH1-CH8
02170-02177:sensor number 4/camera number CH1-CH8
02190-02197:sensor number 5/camera number CH1-CH8*
02210-02217:sensor number 6/camera number CH1-CH8*
02230-02237:sensor number 7/camera number CH1-CH8*
02250-02257:sensor number 8/camera number CH1-CH8*
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
Alarm input/
output Input ÷ ÷ *****(1):
02430:Sensor 1 02440:Sensor 2 02450:Sensor 3
02460:Sensor 4 02470:Sensor 5* 02480:Sensor 6*
02490:Sensor 7* 02500:Sensor 8*
*****(2):
00000:EXTorMD-A 00001:EXTorMD-B
00002:EXT&MD-A 00003:EXT&MD-B
00004:EXT 00005:MD-A
00006:MD-B
**(3):Error type (Refer to page 4.)
Output 1/CAM ÷ ÷ *****(1):
02431:Sensor 1 02441:Sensor 2 02451:Sensor 3
02461:Sensor 4 02471:Sensor 5* 02481:Sensor 6*
02491:Sensor 7* 02501:Sensor 8*
*****(2):
<For DX-TL308E series> 00000-00007:1-8, 65535:-
<For DX-TL304E series> 00000-00003:1-4, 65535:-
**(3):Error type (Refer to page 4.)
Output 1/P.set ÷ ÷ *****(1):
02432:Sensor 1 02442:Sensor 2 02452:Sensor 3
02462:Sensor 4 02472:Sensor 5* 02482:Sensor 6*
02492:Sensor 7* 02502:Sensor 8*
*****(2):00000-00047:01-48, 65535:-
**(3):Error type (Refer to page 4.)
Output 2/CAM ÷ ÷ *****(1):
02433:Sensor 1 02443:Sensor 2 02453:Sensor 3
02463:Sensor 4 02473:Sensor 5* 02483:Sensor 6*
02493:Sensor 7* 02503:Sensor 8*
*****(2):
<For DX-TL308E series> 00000-00007:1-8, 65535:-
<For DX-TL304E series> 00000-00003:1-4, 65535:-
**(3):Error type (Refer to page 4.)
Output 2/P.set ÷ ÷ *****(1):
02434:Sensor 1 02444:Sensor 2 02454:Sensor 3
02464:Sensor 4 02474:Sensor 5* 02484:Sensor 6*
02494:Sensor 7* 02504:Sensor 8*
*****(2):00000-00047:01-48, 65535:-
**(3):Error type (Refer to page 4.)
Output 3/CAM ÷ ÷ *****(1):
02435:Sensor 1 02445:Sensor 2 02455:Sensor 3
02465:Sensor 4 02475:Sensor 5* 02485:Sensor 6*
02495:Sensor 7* 02505:Sensor 8*
*****(2):
<For DX-TL308E series> 00000-00007:1-8, 65535:-
<For DX-TL304E series> 00000-00003:1-4, 65535:-
**(3):Error type (Refer to page 4.)
Output 3/P.set ÷ ÷ *****(1):
02436:Sensor 1 02446:Sensor 2 02456:Sensor 3
02466:Sensor 4 02476:Sensor 5* 02486:Sensor 6*
02496:Sensor 7* 02506:Sensor 8*
*****(2):00000-00047:01-48, 65535:-
**(3):Error type (Refer to page 4.)

17
Command code table (continued)
RS-232C [Direct operation specification] menu setting command form <Recording setting-Manual
setting (Recording B)> (1/2)
*: The commands marked with asterisk (*) are not available with DX-TL304E series.
Menu Menu item Command Status Note
Manual setting (Recording B)
Picture size Picture size <Menu setting>
DW,*****
(1)
*****
(2)
≤
<Inquiry for
setting information>
DR,*****
(1)
≤
<Writing of menu information>
RC≥EX,**(3)DW,***
**(1)*****(2) ≥
<Reading of menu information>
RC≥EX,**(3)DR,
*****(1),*****(2) ≥
*****(1):03000
*****(2):
00000:4CIF 00001:2CIF
00002:CIF
**(3):Error type (Refer to page 4.)
Long recording
mode ÷ ÷ *****(1):12044
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
Motion detection
recording ÷ ÷ *****(1):03001
*****(2):
00000:Normal recording 00001:Alarm recording
**(3):Error type (Refer to page 4.)
Alarm recording/
Pre-alarm time ÷ ÷ *****(1):03005
*****(2):00000-01800 (0 second-30 minutes)
**(3):Error type (Refer to page 4.)
Alarm recording/
Post-alarm time ÷ ÷ *****(1):03006
*****(2):
00000:Manual
00002-03600 (2 seconds-60 minutes)
**(3):Error type (Refer to page 4.)
Picture
quality and
FPS
Active ÷ ÷ *****(1):
03010:CH1 03011:CH2 03012:CH3
03013:CH4 03014:CH5* 03015:CH6*
03016:CH7* 03017:CH8*
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
Normal
recording/Quality ÷ ÷ *****(1):
03030:CH1 03031:CH2 03032:CH3
03033:CH4 03034:CH5* 03035:CH6*
03036:CH7* 03037:CH8*
*****(2):
00001:L1 00002:L2 00003:L3
00004:L4 00005:L5 00006:L6
00007:L7 00008:L8 00009:L9
**(3):Error type (Refer to page 4.)
Normal
recording/FPS ÷ ÷ *****(1):
03050:CH1 03051:CH2 03052:CH3
03053:CH4 03054:CH5* 03055:CH6*
03056:CH7* 03057:CH8*
*****(2):
00002:25 FPS 00004:12.5 FPS 00008:6.25 FPS
00016:3 FPS 00032:1.5 FPS 00064:0.8 FPS
00128:0.4 FPS 00256:0.2 FPS 65535:- - -
**(3):Error type (Refer to page 4.)
Alarm recording/
Quality ÷ ÷ *****(1):
03070:CH1 03071:CH2 03072:CH3
03073:CH4 03074:CH5* 03075:CH6*
03076:CH7* 03077:CH8*
*****(2):
00001:L1 00002:L2 00003:L3
00004:L4 00005:L5 00006:L6
00007:L7 00008:L8 00009:L9
**(3):Error type (Refer to page 4.)
Alarm recording/
FPS ÷ ÷ *****(1):
03090:CH1 03091:CH2 03092:CH3
03093:CH4 03094:CH5* 03095:CH6*
03096:CH7* 03097:CH8*
*****(2):
00002:25 FPS 00004:12.5 FPS 00008:6.25 FPS
00016:3 FPS 00032:1.5 FPS 00064:0.8 FPS
00128:0.4 FPS 00256:0.2 FPS 65535:- - -
**(3):Error type (Refer to page 4.)

18
Command code table (continued)
RS-232C [Direct operation specification] menu setting command form <Recording setting-Manual
setting (Recording B)> (2/2)
*: The commands marked with asterisk (*) are not available with DX-TL304E series.
Menu Menu item Command Status Note
Manual setting (Recording B) (continued)
Alarm
camera
setting
Recording
camera
<Menu setting>
DW,*****
(1)
*****
(2)
≤
<Inquiry for
setting information>
DR,*****
(1)
≤
<Writing of menu information>
RC≥EX,**(3)DW,***
**(1)*****(2) ≥
<Reading of menu information>
RC≥EX,**(3)DR,
*****(1),*****(2) ≥
*****(1):
(For DX-TL304E series, commands of CH 5 to 8 are not available.)
03110-03117:sensor number 1/camera number CH1-CH8
03130-03137:sensor number 2/camera number CH1-CH8
03150-03157:sensor number 3/camera number CH1-CH8
03170-03177:sensor number 4/camera number CH1-CH8
03190-03197:sensor number 5/camera number CH1-CH8*
03210-03217:sensor number 6/camera number CH1-CH8*
03230-03237:sensor number 7/camera number CH1-CH8*
03250-03257:sensor number 8/camera number CH1-CH8*
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
Alarm input/
output Input ÷ ÷ *****(1):
03430:Sensor 1 03440:Sensor 2 03450:Sensor 3
03460:Sensor 4 03470:Sensor 5* 03480:Sensor 6*
03490:Sensor 7* 03500:Sensor 8*
*****(2):
00000:EXTorMD-A 00001:EXTorMD-B
00002:EXT&MD-A 00003:EXT&MD-B
00004:EXT 00005:MD-A
00006:MD-B
**(3):Error type (Refer to page 4.)
Output 1/CAM ÷ ÷ *****(1):
03431:Sensor 1 03441:Sensor 2 03451:Sensor 3
03461:Sensor 4 03471:Sensor 5* 03481:Sensor 6*
03491:Sensor 7* 03501:Sensor 8*
*****(2):
<For DX-TL308E series> 00000-00007:1-8, 65535:-
<For DX-TL304E series> 00000-00003:1-4, 65535:-
**(3):Error type (Refer to page 4.)
Output 1/P.set ÷ ÷ *****(1):
03432:Sensor 1 03442:Sensor 2 03452:Sensor 3
03462:Sensor 4 03472:Sensor 5* 03482:Sensor 6*
03492:Sensor 7* 03502:Sensor 8*
*****(2):00000-00047:01-48, 65535:-
**(3):Error type (Refer to page 4.)
Output 2/CAM ÷ ÷ *****(1):
03433:Sensor 1 03443:Sensor 2 03453:Sensor 3
03463:Sensor 4 03473:Sensor 5* 03483:Sensor 6*
03493:Sensor 7* 03503:Sensor 8*
*****(2):
<For DX-TL308E series> 00000-00007:1-8, 65535:-
<For DX-TL304E series> 00000-00003:1-4, 65535:-
**(3):Error type (Refer to page 4.)
Output 2/P.set ÷ ÷ *****(1):
03434:Sensor 1 03444:Sensor 2 03454:Sensor 3
03464:Sensor 4 03474:Sensor 5* 03484:Sensor 6*
03494:Sensor 7* 03504:Sensor 8*
*****(2):00000-00047:01-48, 65535:-
**(3):Error type (Refer to page 4.)
Output 3/CAM ÷ ÷ *****(1):
03435:Sensor 1 03445:Sensor 2 03455:Sensor 3
03465:Sensor 4 03475:Sensor 5* 03485:Sensor 6*
03495:Sensor 7* 03505:Sensor 8*
*****(2):
<For DX-TL308E series> 00000-00007:1-8, 65535:-
<For DX-TL304E series> 00000-00003:1-4, 65535:-
**(3):Error type (Refer to page 4.)
Output 3/P.set ÷ ÷ *****(1):
03436:Sensor 1 03446:Sensor 2 03456:Sensor 3
03466:Sensor 4 03476:Sensor 5* 03486:Sensor 6*
03496:Sensor 7* 03506:Sensor 8*
*****(2):00000-00047:01-48, 65535:-
**(3):Error type (Refer to page 4.)

19
Command code table (continued)
RS-232C [Direct operation specification] menu setting command form <Recording setting-Manual
setting (Recording C)> (1/2)
*: The commands marked with asterisk (*) are not available with DX-TL304E series.
Menu Menu item Command Status Note
Manual setting (Recording C)
Picture size Picture size <Menu setting>
DW,*****
(1)
*****
(2)
≤
<Inquiry for
setting information>
DR,*****
(1)
≤
<Writing of menu information>
RC≥EX,**(3)DW,***
**(1)*****(2) ≥
<Reading of menu information>
RC≥EX,**(3)DR,
*****(1),*****(2) ≥
*****(1):04000
*****(2):
00000:4CIF 00001:2CIF
00002:CIF
**(3):Error type (Refer to page 4.)
Long recording
mode ÷ ÷ *****(1):12045
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
Motion detection
recording ÷ ÷ *****(1):04001
*****(2):
00000:Normal recording 00001:Alarm recording
**(3):Error type (Refer to page 4.)
Alarm recording/
Pre-alarm time ÷ ÷ *****(1):04005
*****(2):00000-01800 (0 second-30 minutes)
**(3):Error type (Refer to page 4.)
Alarm recording/
Post-alarm time ÷ ÷ *****(1):04006
*****(2):
00000:Manual
00002-03600 (2 seconds-60 minutes)
**(3):Error type (Refer to page 4.)
Picture
quality and
FPS
Active ÷ ÷ *****(1):
04010:CH1 04011:CH2 04012:CH3
04013:CH4 04014:CH5* 04015:CH6*
04016:CH7* 04017:CH8*
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
Normal
recording/Quality ÷ ÷ *****(1):
04030:CH1 04031:CH2 04032:CH3
04033:CH4 04034:CH5* 04035:CH6*
04036:CH7* 04037:CH8*
*****(2):
00001:L1 00002:L2 00003:L3
00004:L4 00005:L5 00006:L6
00007:L7 00008:L8 00009:L9
**(3):Error type (Refer to page 4.)
Normal
recording/FPS ÷ ÷ *****(1):
04050:CH1 04051:CH2 04052:CH3
04053:CH4 04054:CH5* 04055:CH6*
04056:CH7* 04057:CH8*
*****(2):
00002:25 FPS 00004:12.5 FPS 00008:6.25 FPS
00016:3 FPS 00032:1.5 FPS 00064:0.8 FPS
00128:0.4 FPS 00256:0.2 FPS 65535:- - -
**(3):Error type (Refer to page 4.)
Alarm recording/
Quality ÷ ÷ *****(1):
04070:CH1 04071:CH2 04072:CH3
04073:CH4 04074:CH5* 04075:CH6*
04076:CH7* 04077:CH8*
*****(2):
00001:L1 00002:L2 00003:L3
00004:L4 00005:L5 00006:L6
00007:L7 00008:L8 00009:L9
**(3):Error type (Refer to page 4.)
Alarm recording/
FPS ÷ ÷ *****(1):
04090:CH1 04091:CH2 04092:CH3
04093:CH4 04094:CH5* 04095:CH6*
04096:CH7* 04097:CH8*
*****(2):
00002:25 FPS 00004:12.5 FPS 00008:6.25 FPS
00016:3 FPS 00032:1.5 FPS 00064:0.8 FPS
00128:0.4 FPS 00256:0.2 FPS 65535:- - -
**(3):Error type (Refer to page 4.)

20
Command code table (continued)
RS-232C [Direct operation specification] menu setting command form <Recording setting-Manual
setting (Recording C)> (2/2)
*: The commands marked with asterisk (*) are not available with DX-TL304E series.
Menu Menu item Command Status Note
Manual setting (Recording C) (continued)
Alarm
camera
setting
Recording
camera
<Menu setting>
DW,*****
(1)
*****
(2)
≤
<Inquiry for
setting information>
DR,*****
(1)
≤
<Writing of menu information>
RC≥EX,**(3)DW,***
**(1)*****(2) ≥
<Reading of menu information>
RC≥EX,**(3)DR,
*****(1),*****(2) ≥
*****(1):
(For DX-TL304E series, commands of CH 5 to 8 are not available.)
04110-04117:sensor number 1/camera number CH1-CH8
04130-04137:sensor number 2/camera number CH1-CH8
04150-04157:sensor number 3/camera number CH1-CH8
04170-04177:sensor number 4/camera number CH1-CH8
04190-04197:sensor number 5/camera number CH1-CH8*
04210-04217:sensor number 6/camera number CH1-CH8*
04230-04237:sensor number 7/camera number CH1-CH8*
04250-04257:sensor number 8/camera number CH1-CH8*
*****(2):
00000:Off 00001:On
**(3):Error type (Refer to page 4.)
Alarm input/
output Input ÷ ÷ *****(1):
04430:Sensor 1 04440:Sensor 2 04450:Sensor 3
04460:Sensor 4 04470:Sensor 5* 04480:Sensor 6*
04490:Sensor 7* 04500:Sensor 8*
*****(2):
00000:EXTorMD-A 00001:EXTorMD-B
00002:EXT&MD-A 00003:EXT&MD-B
00004:EXT 00005:MD-A
00006:MD-B
**(3):Error type (Refer to page 4.)
Output 1/CAM ÷ ÷ *****(1):
04431:Sensor 1 04441:Sensor 2 04451:Sensor 3
04461:Sensor 4 04471:Sensor 5* 04481:Sensor 6*
04491:Sensor 7* 04501:Sensor 8*
*****(2):
<For DX-TL308E series> 00000-00007:1-8, 65535:-
<For DX-TL304E series> 00000-00003:1-4, 65535:-
**(3):Error type (Refer to page 4.)
Output 1/P.set ÷ ÷ *****(1):
04432:Sensor 1 04442:Sensor 2 04452:Sensor 3
04462:Sensor 4 04472:Sensor 5* 04482:Sensor 6*
04492:Sensor 7* 04502:Sensor 8*
*****(2):00000-00047:01-48, 65535:-
**(3):Error type (Refer to page 4.)
Output 2/CAM ÷ ÷ *****(1):
04433:Sensor 1 04443:Sensor 2 04453:Sensor 3
04463:Sensor 4 04473:Sensor 5* 04483:Sensor 6*
04493:Sensor 7* 04503:Sensor 8*
*****(2):
<For DX-TL308E series> 00000-00007:1-8, 65535:-
<For DX-TL304E series> 00000-00003:1-4, 65535:-
**(3):Error type (Refer to page 4.)
Output 2/P.set ÷ ÷ *****(1):
04434:Sensor 1 04444:Sensor 2 04454:Sensor 3
04464:Sensor 4 04474:Sensor 5* 04484:Sensor 6*
04494:Sensor 7* 04504:Sensor 8*
*****(2):00000-00047:01-48, 65535:-
**(3):Error type (Refer to page 4.)
Output 3/CAM ÷ ÷ *****(1):
04435:Sensor 1 04445:Sensor 2 04455:Sensor 3
04465:Sensor 4 04475:Sensor 5* 04485:Sensor 6*
04495:Sensor 7* 04505:Sensor 8*
*****(2):
<For DX-TL308E series> 00000-00007:1-8, 65535:-
<For DX-TL304E series> 00000-00003:1-4, 65535:-
**(3):Error type (Refer to page 4.)
Output 3/P.set ÷ ÷ *****(1):
04436:Sensor 1 04446:Sensor 2 04456:Sensor 3
04466:Sensor 4 04476:Sensor 5* 04486:Sensor 6*
04496:Sensor 7* 04506:Sensor 8*
*****(2):00000-00047:01-48, 65535:-
**(3):Error type (Refer to page 4.)