Mitsubishi NR-261UM-07LAN4 User manual

SERVICE MANUAL
MITSUBISHI ELECTRIC CORP. SANDA WORKS
Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
SE036711083E Ver.ppt11E NR-261UM-07LAN4,-07-5WS
MITSUBISHI MOTORS
HDD/DVD CAR NAVIGATION SYSTEM
2012 Jun.
Model No. : NR-261UM-07LAN4,-07-5WS
MELCO Model Code : 3AP211,213
CONTENTS
● FEATURES and SPECIFICATIONS..................................................2
● OPERATION .....................................................................................3
● CONNECTORS .......................................................................... 4～5
● COMPOSITION ................................................................................6
● SYSTEM CONFIGURATION .........................................................7,8
● BLOCK DIAGRAM ............................................................................9
● DISASSEMBLING PROCEDURES ........................................ 10～31
● PARTS LIST....................................................................................32
● ELECTRICAL PARTS LIST..................................................... 33～56
● PARTS LAYOUT ON PRINTED CIRCUIT BOARD ................. 57～72
● SCHEMATIC DIAGRAM ....................................................... 73～106
● VOLTAGE .....................................................................................107
● WAVEFORM .................................................................................108
PART No. : 8750A238,MZ360390EX
*This service manual is for model revision E(NR-261UM-07LAN4), and
F(NR-261UM-07-5WS) and later revision.

2Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
FEATURES and SPECIFICATIONS
< Navi Part >
●HDD (Hard Disk Drive) navigation.
●Detecting the car position by GPS (Global Positioning System) signal, gyro
sensor and speed pulse signal.
●Calculating the route.
●Navigating the route by voice and display guidance.
< Audio Part >
●Receiving AM / FM.
●Supporting CD, CD-R / RW, DVD Video, MP3, WMA.
●CD recording / play.
●4ch Amplifier / Fixed EQ (6 bands x 4 ch).
< Monitor Part >
●6.95" wide TFT LCD.
●Brightness adjustment function.
●Supporting Touch Panel.
●Supporting Tactile Switch.
●Illumination function for Tactile Switch.
< Others >
●External VTR connectable.
●Supporting RSES connection.
●Supporting Premium Amplifier connection.
●Steering Remote Control function.
●CAN-BOX operating function.
●Hands-free module operating function.
●Sirius tuner operating function.
●Supported iPod / Bluetooth Audio Hands-free Module connection.
●Supported USB-BOX connection.
FEATURES
●Power supply : DC 13.2V
●Operating voltage : 10 ~ 16V (BATTERY, ACCESSORY Line)
●Ground polarity : Negative ground
●Dark current : Max. 2.5mA (*1)
●Consumption current : Max. 13A / Typ. 5A (*2)
●Output : 45W x 4 (max.) (14.4V)
●Storage temperature range : -30 ~ +85℃
●Working temperature range : -20 ~ +65℃
●Dimensions (W ×D ×H) : 207.8mm ×191.1mm ×106.3mm
●Weight : 3650g
(*1)...Measured 90 sec. after from ACC-OFF, at normal temperature, option
unconnected, CD uninserted, power supply voltage 13.2V.
(*2)...At normal temperature, CD 1kHz, 0dB, output 1W, monitor brightness MAX,
power supply 13.2V.
SPECIFICATIONS

3Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
OPERATION
PANEL CLOSE
PANEL OPEN
MODE Button
AUDIO Button
VOL Button
PWR Button
SET Button
OPEN Button
INFO Button
NAVI Button
SCALE Button
MENU Button
JOY Key
(ENT Button)
Disc Insertion Slot
J1001
Version Up Key Terminal 4P
Disc In Indicator
Disc Eject Button
Guide LED

4Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
CONNECTORS
ANT001
Radio Antenna
Connector 1P
P708
Navi Power Supply
Connector 5P
P705
Rear Camera
Connector 12P
P707
RSES Connector 3P
P20C
Digital Sound Output Connector 4P
P703
VTR & Remote Control
Connector P32
P1G1
External Equipment
Connector 7P
P2A1
Audio Power Supply
Connector 17P
P2Z0
GPS Antenna Connector 2P
J1001 PinNo. Signal Name
1I2C-SDA
2GND
3I2C-SCL
4I2C-VCC
Version Up Key Terminal 4P
P708 PinNo. Signal Name
1GND
2PS-R
3 -
4 -
5BATTERY(+)
Navi Power Supply Connector 5P
*Connector figures are view where it faced the unit.
*Attention of pin numbering different from schematic diagram.
RSES Connector 3P
P707 PinNo. Signal Name
1 SHIELD (REAR)
2 REAR SIGNAL
3 -
P20C PinNo. Signal Name
1-
2-
3-
4-
SH SHIELD
Digital Sound Output Connector 4P
P2A1 PinNo. Signal Name PinNo. Signal Name
1 MAIN GN D 10 BATTERY (+)
2 SPEAKER RR- 11 SPEAKER RR+
3 SPEAKER FR- 12 SPEAKER FR+
4 AMP DATA 13 ACCESSORY (+)
5 - 14VSS
6 SHIELD (AMP DATA) 15 SPEAKER FL+
7 SPEAKER FL- 16 SPEAKER RL+
8 SPEAKER RL- 17 ILL+
9 ILL CONTROL
Audio Power Supply Connector 17P
ANT001 PinNo. Signal Name
1 R AD IO AN TE N NA SIGN AL
SH SHIELD
Radio Antenna Connector 1P
P001
TMC Antenna Distribution
Output Connector 3P
P603
TMC Antenna
Connector 3P

5Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
CONNECTORS
*Connector figures are view where it faced the unit.
*Attention of pin numbering different from schematic diagram.
P703 PinNo. Signal Name PinNo. Signal Name
1 - 17-
2 - 18-
3TELMUTE 19-
4 STEERING REMOTE 20 SHIELD (STEERING REMOTE)
5 - 21 SHIELD (CAN-BOX DATA)
6 - 22-
7 - 23-
8 SHIELD (VIDEO-2L/R) 24 VIDEO2 DETECT
9 VIDEO2-R 25 VIDEO2-L
10 VIDEO2-IN 26 SHIELD (VIDEO2-IN)
11 HFM SIGNAL (-)-GND 27 -
12 HFM SIGNAL (+)-R 28 HFM SIGNAL(+)-L
13 - 29 -
14 CAN-BOX DATA RX 30 CAN-BOX DATA TX
15 - 31 CAN-BOX DATA CLK
16 - 32 -
VTR & Remote Control Connector P32
P705 PinNo. Signal Name PinNo. Signal Name
1CAMERADETECT 7 -
2 SHIELD (CAMERA) 8 -
3 - 9 -
4 C AME R A SIGN AL 1 0 -
5GND(RC) 11-
6VCC(RC6.5V) 12-
Rear Camera Connector 12P
P1G1 PinNo. Signal Name
1SIRIUS-R
2 S-GND (SIRIUS-L/R)
3SIRIUS-L
4BUS(-)
5BUS(+)
6AMPPOWERON
7 ANTENNA-POWER
External Equipment Connector 7P
P2Z0 PinNo. Signal Name
1 GND-GPS
2 GPS ANTENNA SIGNAL
GPS Antenna Connector 2P
P603 PinNo. Signal Name
1 TMC DETECT IN
2 TMC ANTENNA GND
3 TMC ANTENNA SIGNAL
TMC Antenna Connector 3P
P001 PinNo. Signal Name
1 TMC DETECT OUT
2 ANTENNA OUT GND
3ANTENNAOUT
TMC Antenna Distribution Output Connector 3P

6Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
COMPOSITION

7Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
SYSTEM CONFIGURATION
CAN Unsupported
10MY-NAS
2DIN
Audio Navi
All-in-one
GPS Antenna Connector
GPS Antenna
Radio Antenna
Radio Antenna Connector
Navi Power Supply Connector
Audio Power Supply
Connector
Speaker Output
(Premium AMP Connected : FL,FR / Unconnected : FL,FR,RL,RR)
UART Connection (half duplex )
External Equipment Connector
POWER ON
ANT+B
RSES Connector
NTSC (DVD Video)
VTR & Remote Control Connector
VIDEO2 (NTSC, Lch / Rch)
VIDEO2 (Lch / Rch)
VIDEO2 DETECT
HFM SIGNAL (-) : GND
HFT MUTE
VIDEO1 DETECT
Rear Camera Connector
NTSC
Power Supply (+B, GND, BACK)
Vehicle Power Supply, Signal (+B, ACC, ILL+ / -, VSS, GND)
External
AMP
(5.1ch
Unsupported)
(option)
RSES
[Backseat
Display]
(option)
External Voice
Device (option)
Connect either
Steering Remote Control
Hands-free Module
(IE-Bus Supported option)
Rear Camera
(option)
Connect either
Antenna Distribution Output Connector
TMC Antenna Connector Antenna Distribution Cable
Digital Voice Output Connector
BUS(+), BUS(-)
Hands-free Module
(Current after option)
USB-BOX
(IE-Bus Supported option)
HFM SIGNAL (+) : Rch
HFM SIGNAL (+) : Lch
HFM SIGNAL (-) : GND
HFM SIGNAL (+) : Rch
HFM SIGNAL (+) : Lch
HFM SIGNAL (-) : GND
HFM SIGNAL (+) : Rch

8Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
SYSTEM CONFIGURATION
Lch/Rch/SHIELD
Connection
CAN-BOX
Connect
either
Sirius Tuner
(option)
Antenna
CAN-B
ECU
ECU
10MY-NAS
2DIN
Audio Navi
All-in-one
GPS Antenna Connector
GPS Antenna
Radio Antenna
Radio Antenna Connector
Navi Power Supply Connector
Audio Power Supply
Connector
Speaker Output
(Premium AMP Connected : FL,FR / Unconnected : FL,FR,RL,RR)
UART Connection (half duplex )
External Equipment Connector
POWER ON
ANT+B
Power Supply (+B, GND, BACK)
Vehicle Power Supply, Signal (+B, ACC, ILL+, VSS, GND)
External
AMP
(5.1ch
Unsupported)
(option)
Antenna Distribution Output Connector
TMC Antenna Connector Antenna Distribution Cable
Digital Voice Output Connector
BUS(+), BUS(-)
RSES
[Backseat
Display]
(option)
External Voice
Device (option)
RSES Connector
NTSC (DVD Video)
VTR & Remote Control Connector
VIDEO2 (NTSC, Lch / Rch)
VIDEO2 (Lch / Rch)
VIDEO2 DETECT
Steering Remote Control
Connect either
Rear Camera
(option)
Hands-free Module
(IE-Bus Supported option)
Hands-free Module
(Current after option)
USB-BOX
(IE-Bus Supported option)
HFM SIGNAL (-) : GND
HFT MUTE
VIDEO1 DETECT
Rear Camera Connector
NTSC
HFM SIGNAL (+) : Rch
HFM SIGNAL (+) : Lch
HFM SIGNAL (-) : GND
HFM SIGNAL (+) : Rch
HFM SIGNAL (+) : Lch
HFM SIGNAL (-) : GND
HFM SIGNAL (+) : Rch
CAN Supported

9Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
BLOCK DIAGRAM
The machine for CAN is
controlled by CAN-BOX.
Hands-free
Module
VIDEO2
(RSES / AUX)
Navi part
(PCB-DIGITAL)
GPS Antenna
GPS
RF
HDD
40GB
DDR-
SDRAM
128MB
Gyro
Sensor
A/ D
Converter
Navi
μ-com
(Navi
core)
SDRAM
8MB
DSP
CD/
DVD
Flash
ROM
2MB
POWER
SUPPLY
Rear
Camera
Display part
(PCB-MONITOR)
LCD
Module
(6.95
inch)
Touch Panel
Timing
Controller
Image
Signal
Processing
RGB
VIDEO
Monitor
μ-com Operation Key
(AUDIO,SET,INFO,NAVI,SCALE,MENU,JOY)
Operation Key
(MODE,VOL,POWER,OPEN)
VERSION UP KEY
Steering Remote Control
Navi
Sub
μ-com
D/A
Converter
D/A
Converter
Volume
Adjustment
Video
Switch
DVD-
VIDEO
VIDEO2
CAMERA
TMC
Decoder
TMC
Tuner
Detect IE-Bus I/F
Audio part
(PCB-AUDIO)
Navi part
(PCB-ANALOG)
VIDEO
AMP
I / F
VIDEO SIGNAL
Open / Close
Mecha
Drive
Open /
Close
Mecha
A/D
Audio
μ-com
EEPROM
0.25kB
AM/
FM
Tuner
FM
FM
AM
Distri-
bute
Circuit
AM
NK
VIDEO2
Hands-free
Voice
Play Music (HDD)
CD / DVD
Guide Voice
DSP
M
U
T
E
POWER
SUPPLY
POWER
IC
Operation Sound
Sirius
Tuner
Premium
AMP
FL
FR
RL
RR
RSES
CAN
-BOX
CAN-B
IE-Bus supported. Additional connection
with USB-BOX, JCI Hands-free module.
AM

10 Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
DISASSEMBLING PROCEDURES
M084(1): NAME-CARD(NR-261UM-07LAN4)/
M085(2): NAME-CARD(NR-261UM-07-5WS)
Ⓑx 4
M024: PIN-MONI
M024: PIN-MONI
M068: ASSY-COVER-F
M051: PANEL-HDD
0.4 +0.15/-0.05PIN-MONIM024
Tighten torque(N・ｍ）Screw/NameNo.
Ⓑ0.7 +0.2/-0.1M3X6
●Disassembling procedures
In reverse of assembling procedures.
●Assembling procedures
1.Insert the S7-HDD to the S2-CHASSIS, and screw the two screws.
2.Set M051.
3.Pull out the slide part of the S2-CHASSIS, and screw M086 with
the four screws (Ⓑ), and M024.
4.Insert the FPC of M086 to the S2-CHASSIS.
5.Set back the slide after M068 set.
S2-CHASSIS
S7-HDD
Two screws
Fold and set.
Set this hook at first.
Slide
Continuity side
Lock after FPC inserted.
Do not break hexagon socket.
Top
M086: S2-MONI
(1) NR-261UM-07LAN4
(2) NR-261UM-07-5WS
Mod e l
Latch the hook at right and left,
then push the top. (After
assembling, check if M068
and the panel is seamless.)

11 Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
DISASSEMBLING PROCEDURES
●Disassembling procedures
In reverse of assembling procedures.
●Assembling procedures
1.Screw M016 with the two screws(Ⓐ) and the three screws(Ⓒ).
2.Screw the nine screws(Ⓒ) and the two screws(Ⓚ).
Ⓒx 9
Ⓚx 2
Ⓐx 2
Ⓒx 3
M016: COVER-TOP
M3X6 0.4 +0.2/-0.1Ⓐ
Refer in the fig.2.6X4Ⓒ
Tighten torque(N・ｍ）ScrewNo.
Ⓚ0.7 +0.2/-0.1M3X10
Tighten torque(N ・m) : 0.3 +0.05/-0.05
Tighten torque(N ・m) : 0.4 +0.2/-0.1
Latch the two hooks.

12 Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
DISASSEMBLING PROCEDURES
●Disassembling procedures
In reverse of assembling procedures.
●Assembling procedures
1.Hook M076 to M070, and screw the five screws(Ⓙ).
2.Pull out the slide part of the S3-CHASSIS, and pass the arm through
to the hole of the S3-PANEL-SUB.<Step1~3>
3.Screw the three screws(Ⓐ).
Ⓐx 3
Ⓙx 5
M076: ASSY-PCB-PANEL M070: ASSY-PANEL-SUB
M3X6 0.7 +0.2/-0.1Ⓐ
0.12 +0.01/-0.012X4Ⓙ
Tighten torque(N・ｍ）ScrewNo.
S3-CHASSIS
S3-PANEL-SUB
Remove the arm protector.
Remove the arm protector.
(1)After pull out the slide chassis till it stops, pass the
tip through to panel each one side. <Step1>
<Step1> Pass the tip of slide chassis
through to panel by each.
Slide chassis
S3-PANEL-SUB
Arm
Arm
<Step2> After passed the arm of one
side, pass the another side of arms.
<Step3> Push the front of panel.
(2)After passed the one arm, pass another
arm with bending it internally. <Step2>
Do not give scratch to panel by arms.
(3)Push the front of panel to
connector mating. <Step3>
(4) Push the square holes at side(two places) and
downside(three places), till the hooks set.<Step3>
Latch M076 to the hooks.

13 Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
DISASSEMBLING PROCEDURES
●Disassembling procedures
In reverse of assembling procedures.
●Assembling procedures
1.Screw M010 to M025 with two screws(Ⓚ).
2.Connect LEAD-CONNECTOR of the S4-HEAT SINK to the S4-CHASSIS.
3.Screw the S4-HEAT-SINK with four screws(Ⓐ).
M3X6 0.7 +0.2/-0.1Ⓐ
0.7 +0.2/-0.1M3X10Ⓚ
Tighten torque(N・ｍ）ScrewNo.
Ⓐx 4
Ⓚx 2
M025: HEAT-SINK
M010: MOTOR-FAN
S4-HEAT-SINK
S4-CHASSIS
LEAD-CONNECTOR

14 Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
DISASSEMBLING PROCEDURES
●Disassembling procedures
In reverse of assembling procedures.
●Assembling procedures
1.Screw M082 with the two screws(Ⓐ).
2.Screw the COVER-DV3 with the one screw(Ⓐ).
3.Connect the FPC to M082.
M3X6 0.7 +0.2/-0.1Ⓐ
Tighten torque(N・ｍ）ScrewNo.
Ⓐx 2
Ⓐ
M082: ASSY-PCB-CONN
Pass salient to the square hole
on the circuit board.
Fit reentrant on the circuit board
to salient.
Set FPC to COVER-DV3.
Lock after FPC connected.
FPC

15 Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
DISASSEMBLING PROCEDURES
●Disassembling procedures
In reverse of assembling procedures.
●Assembling procedures
1.Connect FFC from S5-CHASSSIS to S5-DECK.
2.Fit the salients and put S5-DECK to S5-CHASSIS.
3.Set FPC-1 at the hooks of S5-DECK.
4.Insert the FFC to the cover of the S5-DECK. (View J)
5.Set M012, and screw the five screws(Ⓐ) and two screws(Ⓒ).
6.Connect FPC-2 from S5-DECK to S5-CHASSIS. Ⓐx 3
Ⓐx 2
Ⓒx 2
M012: CHASSIS-L
S5-DECK
S5-CHASSIS
FPC-2 FPC-1
FFC
Lock after FPC connected.
Set FPC-1 at these hooks.
Fit the dowels.
Insert M012 from downside surely.
Latch the hooks to the
square holes.
Fit the dowels.
Fit the square holes
to the salients.
Lock after FFC connected.
Continuity side
M3X6 0.7 +0.2/-0.1Ⓐ
0.4 +0.2/-0.12.6X4Ⓒ
Tighten torque(N・ｍ）ScrewNo.
FFC
View J
View J
FFC
Insert

16 Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
DISASSEMBLING PROCEDURES
●Disassembling procedures
In reverse of assembling procedures.
●Assembling procedures
1.Set M015 and screw the five screws(Ⓒ).
2.Remve the separator and stick M035 to M015.
3.Set M077 to S5-CHASSIS while matching the two salients.
4.Connect FFC from HDD circuit on S5-CHASSIS to M077.(View F)
5.Stick M029 to Navicore of M077.
6.Set M067, and screw the one screw(Ⓓ) and the four screws(Ⓔ).
0.4 +0.2/-0.1M2.6X3Ⓓ
2.6X4 0.4 +0.2/-0.1Ⓒ
0.4 +0.2/-0.1M2.6X6Ⓔ
Tighten torque(N・ｍ）ScrewNo.
Ⓔx 4
Ⓓ
Ⓒx 5
M067: ASSY-SHIELD
M029: SHEET-HS
M077: ASSY-PCB-DIGITAL
M035: SHEET-DI
M015: CASE-DIGITAL
Put on the Navicore.
Lock after FFC
connected.
FFC from HDD.
View F
Engage the connectors.
(Push “PUSH” on circuit board)
Fold
Remove the connector covers.
Fit the dowel to the hole.
Fit the salient of post to
the hole.
S5-CHASSIS
Be careful to not change
the shape when
assembling.

17 Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
DISASSEMBLING PROCEDURES
●Disassembling procedures
In reverse of assembling procedures.
●Assembling procedures
1.Connect M007 to M083. (Either direction of the connector can be connected.)
2.Screw the M083 with the one screw(Ⓐ).
3.Latch the hook of M007 to the hook.
4.Connect M007 to M081.
M3X6 0.7 +0.2/-0.1Ⓐ
Tighten torque(N・ｍ）ScrewNo.
M007: LEAD-CONNECTOR 4P
M083: ASSY-PCB-SENSOR
Ⓐ
M081: ASSY-PCB-ANALOG
Fig. A
Pass the Lead-Connector
to area A of Fig. A.
Latch the Lead-Connector
to the hook.
Hook latch position.
Assembling Angle of M083
Remove the adsorption sheet
of P604.

18 Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
DISASSEMBLING PROCEDURES
●Disassembling procedures
In reverse of assembling procedures.
●Assembling procedures
1.Screw M081 with the five screws(Ⓐ).
2.Screw the S5-HOLDER with the four screws(Ⓐ) from a→b→c→d.
3.Latch the square hole of M021 to the hook, and set the dowel to the hole. (Fig. B)
4.Screw M021 with the one screw(Ⓐ).
M3X6 0.7 +0.2/-0.1Ⓐ
Tighten torque(N・ｍ）ScrewNo.
Ⓐ
M021: BRACKET-NAVI
Ⓐx 9
S5-HOLDER
Fig. B
There must be no space after
tightening of the screw.
Dowel Hook
a
b
c
d
M081: ASSY-PCB-ANALOG

19 Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
DISASSEMBLING PROCEDURES
●Disassembling procedures
In reverse of assembling procedures.
●Assembling procedures
1.Set the hook of chassis to M081. (View A)
2.Connect M001, M004, M006 to the connectors.
M081: ASSY-PCB-ANALOG
M001: FPC-CON
M004: FLAT-CABLE 30P
M006: FLAT-CABLE 50P
View A
Set M081 from left to right.
Pin 1 (white marking)
Continuity side
Himeron

20 Your company internal use only.Copyright (C) Mitsubishi Electric Corporation.
NR-261UM-07LAN4,-07-5WS
DISASSEMBLING PROCEDURES
●Disassembling procedures
In reverse of assembling procedures.
●Assembling procedures
1.Connect M006 and pull it forward.
2.Remove the separator and stick M032 to M011(revers side).
3.Remove the separator and stick M031 to M011(face side).
4.Set M011 to guide salient, and assemble.
M006: FLAT-CABLE 50P
M032: SHEET-COIL
M011: CHASSIS-ANALOG
M031: SHEET-ANALOG
Lock after FFC connected.
Continuity side
(reverse side)
Pin 1 (white marking)
Pull forward
S5-CHASSIS