Mitsuki CTF-901A User manual

THE USER
THE USERTHE USER
THE USER’
’’
’S GUIDE MANUAL.
S GUIDE MANUAL.S GUIDE MANUAL.
S GUIDE MANUAL.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Caution : Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority to operate the
equipment.
USER
USERUSER
USER’
’’
’S GUIDE MANUAL.
S GUIDE MANUAL.S GUIDE MANUAL.
S GUIDE MANUAL.
✻
✻✻
✻FEATURES
!User selectable alphanumeric display (character zooming)
- 8 line : 20 characters per line(6x8 dots font)
- 4 line : 20 characters per line(6x16 dots font)
- 4 line : 15 characters per line(8x16 dots font)
!Memory Capacity (total 60,000 characters)
- Private 1,000 characters x 20 slot
- Mail drop 1,000 characters x 4 slot x 8 Item

- Notebook 1,000 characters x 8 slot
!Shows Time of Day and Date
!Message Time and Date Stamping
!Message Lock up to 10 Messages
!Reminder Alert for Message(s) Unread (Every 3 minutes)
!Duplicate Message Indication
!Message Slot Scrolling and Page Scrolling
!Individual Message Delete and Erase All
!Memory Full Indication
!Erred message indication
!3 Selectable Alert Mode (Beep, Vibration and Silent)
!10 Selectable Alerts (4 Tones, 6 Musical Alerts)
!4 Selectable Auto Reset Time (12sec, 20sec, 28sec, 36sec)
!Built in Audible Alarm Clock
!Service Area Indication
!LCD brightness controllable
!LCD Back Lighting
!Automatic power On/Off (On/Off time programmable)
!Backup battery for memory Retention during battery replacement
!Battery Level display
!Low Battery Warning for Battery Replacement
Control Buttons
Control ButtonsControl Buttons
Control Buttons
Escape/Power On/
Function Button
Read/Select
Button
Left, Right Directional/
Backlight On Buttons
Escape/Power On/ - Used to display the Function/Message Read Menu, to turn the pager on,
Function Button and to Escape current state.
Left, Right Directional/ - Used to navigate through the Function/Message Read Menu, to preview
Backlight On Buttons your messages, to navigate through time/alarm/auto power on/off
setting functions, and to turn the backlight on(press and hold for two seconds).
Read/Select Button - Used to select a pager function, to activate your selection, to navigate
through time/alarm/auto power on/off setting function, and to display
message manipulate screen(press for two seconds while reading message).
4. Operation
4. Operation4. Operation
4. Operation

Turning Your Pager On
Turning Your Pager OnTurning Your Pager On
Turning Your Pager On
Press and hold "for two seconds. A start-up screen is displayed and your pager activates the initial alert.
Turning Your Pager Off
Turning Your Pager OffTurning Your Pager Off
Turning Your Pager Off
❶Press "to display the function menu.
❷Press #to move the cursor to.
❸Press to turn Pager off.
Your pager is now off and the screen is blank. The buttons are not functioned except "button.
If you press "shortly, “-POWER OFF-“ is displayed with current time and date.
Backlight
BacklightBacklight
Backlight
The Backlight is on at any time by pressing and holding #or!for two seconds.
Using the Function Menu
Using the Function MenuUsing the Function Menu
Using the Function Menu
The Function Menu provides access to the many features of your pager through the use of symbols.
❶Press "to display the function menu.
The location of the cursor is indicated by inverted symbol.
❷Press #or !to move the cursor within the function menu.
As you move through the Function Menu, the function symbols
Inverted to indicate the present location of the cursor.
❸Press to activate function.
To exit from the Function Menu without making Example of Function Menu Screen
any changes or go back to the Message Menu, press ".
Using the Message Read Menu
Using the Message Read MenuUsing the Message Read Menu
Using the Message Read Menu
❶Press #,!or to display the message menu.
❷Press #or!to move within the message menu
(Private, Notebook and Maildrop).
❸Press to read message.
Note: Number of unread message(s). Example of Message Read Menu Screen
Number of stored messages(s).
When the memory is full (20 messages), “FULL” is displayed instead of message number.
Receiving/Reading/Manipulating Personal Messages
Receiving/Reading/Manipulating Personal MessagesReceiving/Reading/Manipulating Personal Messages
Receiving/Reading/Manipulating Personal Messages
Your pager can receive up to 20 personal messages. When a message is received, your pager alerts
according to the current alert setting (audible, vibrate, or no alert).
-Reading an Incoming Message
❶Press to display your message. Press again to read the next screen.
❷Press #or!to go back to the first screen of the message.
-Previewing/Reading/Deleting/locking/unlocking/Moving to Notebook a Stored Message
❶Press #or to display the message menu.
❷Press to display message preview screen. Press #or!to preview the message you want to read.
❸Press to read the detailed message. Press again to read the next screen.
If you want to delete/lock/unlock or move to Notebook the message while reading it, press and hold
for two seconds to display Message Manipulate Screen. Press #or!to move the cursor to the desired
function, and press to activate it.

❹If you want to go back to the preview screen, press ".
Note: When an unread message exists, your pager gives a periodic reminder alert (every 3 minutes)
until all unread messages are read. A on the pager status line indicates that you have unread messages.
Reminder alert is enabled or disabled through the Function Menu. Reminder alerts on, off.
Example of Message Preview Screen Example of Message Read Screen Example of Message Manipulate Screen
Display Zoom
When this feature is activated, the standard 4-line ( 20 characters per line) display is converted
to a 4-line ( 15 characters per line) or 8-line ( 20 characters per line) display.
-To select Display Zoom
❶Press "to display the Function Menu.
❷Press #to move the cursor to , or (current setting).
❸Press to select desired zooming step ( ).
Deleting Messages
-To Delete Single Message while Reading It
❶From the Message Manipulate Screen, press!to move the cursor to .
❷Press to delete the message.
-To Delete All Unlocked Messages
❶From the Function Menu, press #to move the cursor to .
❷Press . “Delete All ?” screen is displayed.
❸Press!to move the cursor to Y.
❹Press . All unlocked messages are deleted.
Note: Notebook messages are not deleted with this feature.
Locking and Unlocking Messages
Up to 10 messages can be locked to prevent them from being deleted
or from being replaced when memory is full. When a message is locked,
the symbol displayed on the Time Stamp line while reading the message.
-To Lock or Unlock a Message while Reading it
❶From the Message Manipulate Screen, press!to move
the cursor to or .
❷Press to lock or unlock the message.
Notebooks
Your pager has eight notebook areas for storing personal messages.
-Storing Personal Messages in Your Notebooks
❶From the Message Manipulate Screen, press#or!to move the cursor to .
❷Press . The message is now in the Notebook.
-Reading/Deleting Messages in Your Notebooks
❶From the Message Read Menu Screen, press!to move the cursor to .
❷Notebook messagesare readand deleted the same way as personal messages.

Note: Notebook messages are deleted one at a time. Storing to notebook is not activated when it is full.
Maildrop/Information Service
Your pager has eight Maildrop areas (Each area has four rooms for storing maildrop messages).
-Reading Messages in Your Maildrop
❶From the Message Read Menu Screen, press#or!to move the cursor to .
❷Maildrop messages are read the same way as personal messages.
-Turning Maildrop Alerts On and Off
❶From the Function Menu Screen, press#or!to move the cursor to alert on
or alert off.
❷Press to turn the maildrop alert on or off.
Setting the Incoming Message Alert
❶From the Function Menu, press #or!to move the cursor to , or (current setting).
❷Press to change the type of alert (audible, vibrate or silent).
Note: The current Alert setting ( , , ) is also displayed on the pager status line.
-Setting the Alert Pattern (Tone or Melody)
❶From the Function Menu, press #to move the cursor to .
❷Press to display the Select Melody screen.
❸Press #or !to move the cursor to desired number.
❹Press to listen the melody or tone.
❺Repeat steps 3 and 4 to select another pattern.
Setting the Time and Date
❶From the Function Menu, press!to move the cursor to .
❷Press to display the Set Time/Date screen.
❸Press #or !to adjust the hour.
❹Press to move the cursor to next set of digits.
❺Repeat steps 3 and 4 to adjust minutes, day/month(or month/day)/year/week.
❻Press "to activate the time and date setting.
Setting the Alarm
❶From the Function Menu, press!to move the cursor to or .
❷Press to display the Set Alarm screen.
❸Press #or !to enable or disable alarm.
❹Press to move the cursor to alarm hour.
❺Press #or !to adjust the hour.
❻Repeat for minutes.
❼Press "to activate the alarm setting.
Note: If alarm is on, the symbol is displayed on the pager status line.
Setting the Auto Power On/Off
❶From the Function Menu, press!to move the cursor to or .
❷Press to display the Set Auto Power On/Off screen.
❸Press #or !to enable or disable auto-power-on/off.
❹Press to move the cursor to auto-off hour digits.
❺Press #or !to adjust the hour of auto-off time.
❻Repeat steps 4 and 5 to adjust the minutes and auto-on time .
❼Press "to activate the auto-power-on/off setting.

Setting the Time Mode
❶From the Function Menu, press!to move the cursor to or (current setting).
❷Press to change the Time Mode to 12 hour time or 24 hour time.
Setting the Date Mode
❶From the Function Menu, press#or !to move the cursor to or (current setting).
❷Press to change the Date Mode to Day/Month/Year or Month/Day/Year.
Adjusting LCD Brightness
❶From the Function Menu, press #or !to move the cursor to .
❷Press to display the LCD Brightness screen.
❸Press #or !to adjust brightness of LCD display.
❹Press "to exit.
Setting the Auto Reset Time (Duration of Display off Time)
❶From the Function Menu, press #or!to move the cursor to , , or (current setting).
❷Press to change the Auto Reset Time.
Battery Information
Your pager is designed to operate with a single AAA-size alkaline battery.
-Low Battery Indication
When the battery is low, “LOW BATTERY !” is displayed with beeping at every 4 minutes.
-Replacing the Battery
To replace the battery, proceed as follows:
❶Unlock the battery door by sliding the door latch away from the battery door.
❷Slide the battery door away from the housing to remove it.
❸Remove the old battery and insert new one in the direction shown on the battery compartment.
-Battery Back-up
Your pager has a backup battery for memory retention during battery replacement.
Note: To protect all the memory when you replace the battery, please change old battery to new one
quickly. And avoid too much key operation during replacing battery.
Linkus Flex Pager Quick Reference
Pager Symbols
Pager Status Symbols: (Top rows of display)
In Range
Unread Message

Alarm On
Audible Alert Mode
Vibrate Alert Mode
Silent Alert Mode
Full Battery Gauge
Low Battery Gauge
AAMTime
PPMTime
24 Hour Time
Message Status Symbols: (Message time-stamp display)
Locked Message
Duplicated Message
Erred Message
Message Manipulate Menu Symbols: (Display while reading message)
Read Next Message
Read Previous Message
Delete Message
Lock Message
Unlock Message
Move to Notebook
Message Menu Symbols
Read Private Message(s)
Read Note Book Message(s)
Read Mail drop Message(s)
Function Menu Symbols
Delete All Messages
Set Display Zooming (20Char 8Line/20Char 4Line/15Char 4Line)
Turn Pager Off
Set Audible/Vibrate/Silent (no audible & vibrate) Alert
Set 12/24 Hour Time mode
Set Alarm
Set Time & Date
Set LCD Brightness
Set Auto On/Off
On/Off Mail drop Alert
On/Off Unread Reminder
Set Date order to “Day/Month/Year” or “Month/Day/Year”
Set Auto Reset Time (Display Time) to 12sec, 20sec, 28sec or 36sec
Choose Alert(tone or melody)

(Function Menu) (Message Menu) (Scan Message) (Read Message) (Manipulate
Message)
Press ", press #or!Press ,#or!Press twice Press while Press for 2 seconds
to move cursor and and #or!for scan scan message while reading message press to activate
Turning Your Pager Off
❶Press "to display the function menu.
❷Press #to move the cursor to .
❸Press to turn Pager off.
Turning Your Pager On
❶Press "for two seconds until the Pager turns on.
Using the Function Menu
❶Press "to display the function menu.
❷Press #or !to move the cursor within the function menu.
❸Press to activate function.
Backlighting
Press #or !for two seconds to activate the backlight.
Setting the Time and Date
❶Press "to display the function menu.
❷Press !to move the cursor to .
❸Press to display the Set-time-and-date screen.
❹Press #or !to adjust the hour.
❺Press to select next set of digits.
❻Repeat for minutes, day/month(or month/day)/year/week.
❼Press "to activate the time and date setting.
Setting the Alarm
❶Press "to display the function menu.
❷Press !to move the cursor to or .
❸Press to display the set-alarm screen.
❹Press #or !to enable or disable the alarm.
❺Press to select alarm hour.
❻Repeat for minutes.
❼Press "to activate the alarm setting.
Note: - alarm disabled, - alarm enabled.
Using the Message Read Menu
❶Press #,!or to display the message menu.
❷Press #or !to move within the message menu (private, notebook and maildrop).
❸Press to read message.
Receiving and Reading Your Messages
❶Press any button to stop the alert.
❷Press to display your message.
❸Press #or !to scan (preview) messages.
❹Press to view detailed message.
❺Press again to advance message screen by screen.
❻Press #or !to go back to the first screen of the message.

❼Press "to go back to the preview (scan) screen.
Deleting/Locking/Unlocking Messages or Adding to Notebook
❶Press for two seconds in the message display screen(not preview screen).
❷Press #or !to move the cursor to desired function.
❸Press to activate the function.