Arct SP-01 User manual

1
Operating Instructions
Staff pager
Model No. SP-01

2
Contents:
Read me first…..3
Warranty Policy…...3
Safety precautions….3
Precautions for use…..5
Confirmation of accessories…..6
Names of parts and their functions…..7
Usin the staff pa er…..8
Replace a battery pack….10
Troubleshoot….12
Specifications…..12

3
Read me first:
Thank you for purchasing the ARCT SP-01 staff pager.
These operating instructions describe the instructions for the SP-01 staff pager.
Before connecting, operating this product, p ease read these instructions comp ete y, and save this
manua for future use.
Here by, we dec are that this SP-01 is in comp iance with Part 15 of the FCC Ru es. Operation is
subject to the fo owing two conditions:
(1) This device may not cause harmfu interference, and (2) This device must accept any
interference received, inc uding interference that may cause undesired
operation.
Warranty Policy:
The warranty period and what is covered are according to app ications, contracts or distributors.
P ease ask our sa es representative.
Note:
The fo owing damages are not covered by the warranty.
-Any secondary damages, inc uding without imitation, business chances.
-Any damages by user inc uding dropping, water contact or any other wrong use, other than the
purpose designed for.
Safety precautions:
To prevent severe injury and oss of ife/property, read this section carefu y before using the unit to
ensure proper and safe operation of your unit.
 The section exp ains the graphic symbo s used in this manua .
Denotes a potential hazard that could result in serious injury or death.

4
Staff pager: SP-01
Do not throw the SP-01 into fire or heat the SP-01. The same applies to the used Ni-H battery.
There is the risk of heat generation, fire, or exp osion.
Do not short positive (+) and negative (-) contact of Ni-H battery.
Dispose of the Ni-H battery after insulating positive (+) and Negative (-) contacts by friction
tape.
There is the risk of heat generation, fire, or exp osion.
Do not charge, use, or leave the SP-01 where temperatures are high such as a place close to fire or
a place under the hot sun. The same applies to the used Ni-H battery.
There is the risk of heat generation, fire, or exp osion.
Do not splash water on the SP-01 or moisten the SP-01 with water.
There is the risk of heat generation, fire, or exp osion.
If the Ni-H battery of SP-01 leaks liquid or smells, do not charge the SP-01 or bring it close to
fire.
There is the risk of heat generation, fire, or exp osion.
Do not touch the electrolyte leaked from the Ni-H battery.
Entry of the e ectro yte into an eye may ead to b indness. In such a case, rinse the affected eye
thorough y with c ean water, and then seek medica attention immediate y.
Do no put the SP-01 into a microwave oven or pressurized chamber.
There is the risk of heat generation, fire, or exp osion.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYEP.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

5
Precautions for use:
Observe the following to use this product correctly.
Staff pager
 Do not open or modify the main unit case.
 The Ni-HM battery of S -01 is a consumable. The Ni-MH battery life, which varies with using
conditions, is approximately a year as a guideline, and after a year or approximately over 500
times of recharging, the recharging capability becomes weak. If the battery is exhausted in a
short time after full recharging, replace the Ni-MH battery with new one.
 Be sure to use the specified Ni-MH battery.
 Do not touch the contact portions of the Ni-MH. Failure to observe the may cause poor
contact.
 Recharge the battery pack at ambient temperatures from 5℃ to 35℃.
 Charging the S -01 before use.
 When the terminal of charging pin becomes dirty, use a dry soft cloth to clean the terminal pin.
Failure to observe this may cause poor contact with the device and cut power supply.
Operation environment and service place
 Do not leave this product in a place exposed to high temperature or excessive dust.
 Do not put this product where static is likely to be generated or where magnetism generating
devices such as a TV set and a radio are nearby.
 Do not leave this product under direct sunshine or at excessive high or low temperatures of
long time.
 rotect this product form rain or water
How to care:
 Use a dry soft cloth to remove dirt from this product. When stubborn stains are observed, use
a tightly twisted water soaked cloth to wipe the point softly and use dry another cloth to wipe
the point again.
 Do not use thinner, benzene, wax, kerosene, polish, hot water, chemical cloth and the like.
 The dirty connector may cause charging failure.

6
Confirmation of Accessories:
Before using, check the following accessories.
 In case some items are missing, contact your dealer.
 Main unit:
 Operating instructions(this document)

7
Names of parts and their functions
 Main unit(front side)
No Name Details
1 Indicator Blink Light green: Standby mode
Light red: charging is under way.
Light red and green: Battery is full charging.
Blink Green & Red alternately: programming mode.
2 Alarm Indicator Flashed red: get a paging signal.
3 Stop key ress this button to stop an alarming page
4 ager ID ager ID number

8
 Main unit(back side)
No Name Detai s
5 Charging
termina
Used for supp y power to this unit and charging it.
6 Back c ip C ip on a be t or vest.
Using the staff pager:
Remove the battery isolation film before using (as below)

9
Charging
The SP-01 can be p aced on the charger (SPC-01).
1. Insert the unit into the charger, a ow unit to charge fu y overnight (the staff page must be
charged at east 16 hours before use)
2. Remove form charger, and pager wi vibrate, beep and f ash.
3. Rep ace the pager in the charger at the end of each day.
Indicator During charging
Light red: Charging is under way
Light green: Battery is fu charging.
assages:
The pager can vibrate, beep, and f ash the a arm ights
Alarming
The staff pager SP-01 wi a arm a certain type and pattern depending on the a arm mode- A1,
A2, or A3 of the ATX-01. That is se ected from the ATX-01 keypad.
Programming
If a new staff pager number needs to be assigned to a pager, staff pager can be reprogrammed form
the ATX-01 transmitter.
 Program Staff pager’s ID number:
Be sure the staff pager is into programming mode -the pager’s indicator LED – Green and Red
LED wi a ternate b inking.
※1

10
The system support OTA to change Pager’s ID.
1. Press FN
2. Press A2/CHG-ID
3. Enter #(# = Pager ID number)
4. Press ENT
When Change ID over-the-air (OTA) command paging is received:
The Staff pager wi beep one time and return back to charging mode
※1： How does the staff pager into programming mode:
Press the “stop” button then put the staff pager into charger.
Re ease the stop key unti the pager into programming
mode--the pager’s indicator LED – Green and Red LED wi
a ternate b inking
Replace a Battery Pack
 How to replace Ni-MH battery
1. Screwed the back cover of the SP- 1 pager

11
2. Take out the Ni-HM battery
3. Replace a new Ni-HM battery
When inserting the Ni-HM battery into the unit, make sure that the terminals are correctly
directed.
4. Close the back co er of SP-01
ut back the back cover of the S -01, and fasten screws

12
Troubleshooting
Symptom Check items and so utions
Pager charger ights DO
NOT come on
 Make sure the pager are comp ete y inserted into the charging
s ot.
 Perhaps the power supp y prob em. Try p ugging transmitter’s
power supp y to the pager charger to figure this issue.
 If staff pager sti cannot be charged, p ease contact our distributor
or sa es representative for assistance
Pager does not receive
any page.
 Reset the SP-01, put the pager on the charger then take it out. It
wi be reset.
 Make sure the Ni-HM battery is good.
 If staff pager sti does not receive any page, p ease contact our
distributor or sa es representative for assistance
Specifications
SP-01 Transmitter
Item Specifications
Frequency 450~470MHz
aud rate: 1200 bps
Modulation type FSK
Channel Spacing 12.5K
Frequency stability 10ppm at -10℃~+60℃
Alert tone volume 85d a @10cm
Current consumption Standby: 3mA
Dimension 75mm x 56mm x 19mm
Weight Approx..XXXg
Power supply 1.2V Ni-HM AAA
attery Life 5 days (full charging)
Certification