Mizerak P5223W User manual

1-866-556-2757
FAX: [phone]
We strive to ensure that our products are of the highest quality
and free of manufacturing defects or missing parts. However, if
you have any problems with your new product,
DO NOT RETURN IT TO THE STORE,
please contact us toll free @:
Or write to:
Escalade Sports
Customer Service Department
P.O. Box 889
Evansville IN 47706
Your Model Number _____________________
P5223W
have your model number when inquiring about parts.
[email protected]
Please
Date Code ________________________
2-P5223W-0910-WJ
© 2012 Escalade Sports For Customer Service Call 1-866-556-2757
When contacting Escalade Sports please provide your model number, date
code (if applicable) and part number if requesting a replacement part. These
numbers are located on the product, packaging, and this owners manual.
1
All Right Reserved.
Purchase Date ________________________
PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

©2012 Escalade Sports For Customer Service Call 1-866-556-2757
2
CAUTION
THE SPRAY ADHESIVE USED FOR APPLYING PLAYFIELD CLOTH IS EXTREMELY FLAMMABLE AND UNDER
PRESSURE
!CAREFULLY READ CAUTIONS ON SPRAY ADHESIVE CONTAINER !KEEP OUT OF THE REACH OF
CHILDREN !DO NOT USE OR STORE NEAR HEAT SOURCE ,FLAMES ,SPARKS OR WHEN SMOKING !WORK
AREA MUST BE WELL VENTILATED
.OPEN DOORS AND WINDOWS WHEN USING SPRAY ADHESIVE .
To ensure safety, do not attempt to assemble system without followinginstruc-
tions carefully. Proper and complete assembly, use, and supervision isessential for
proper operation and to reduce the risk of accident or injury. A high prob-
ability of serious injury exists if this system is not installed, maintained, and
operated properly.
NOTE: This table adds weight to any floor. Be sure floor can withstand this kind of weight. If floor sags,
table will be impossible to level.
•Philips Screwdriver
•Putty Knife
•Needle Nose Plyers
•Adjustable Wrench
•Small Hammer
•Carpenters Level
•Ratchet with socket
•Tape Measure
•Sanding Block
•Scissors or Sharp Knife
Tools Needed: (Not Included)
READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO
ADULTS ARE NEEDED TO PUT THIS TABLE
TOGETHER.
All Right Reserved.

Part List
H14 - Pocket Nail
24 Pcs
T1-Grout Kit
1 Pc 1 Pc 1 Pc
T2-Spray Adhesive T3-Sand Paper
H5 - 3/8” x 3” Bolt
8 Pcs
H7 - F5 x 1-3/4”
Flat Head Screw
16 Pcs
8 Pcs
H1 - 3/8” x 2-1/4” Bolt
Washer 16 Pcs
H2 - 3/8” Spring
32 Pcs
H3 - 3/8” x 25mm Washer
H12 - 5/16” x 1-1/2” Bolt
18 Pcs
H13 - 5/16” x 32 Washer
18 Pcs
H8 - WP/3 x 18mm
Round Washer Head Screw
24 Pcs
H11 - T4 x 15mm
Round Head Screw
24 Pcs
H9 - 5/16” x 1-3/4” Bolt
12 Pcs
H10 - 5/16” x 23mm
Washer 12 pcs
16 Pcs
H4 - 3/8” Hex Nut
H6 - WP/4 x 1”
Round Washer Head Screw
8 Pcs
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
3
All Right Reserved.
T4-Wrench
1 Set
(To Scale)

P1
P2 P3 P4 P5
P6-Slatron
P6S-Slate
P7-Slatron
P7S-Slate
P8 P9
P10 P11 P12 P13
P14
A1 A2 A3 A4
A5 A6
Cue Stick
2 Pcs
Triangle
1 Pc
Brush
1 Pc
Table Cloth
1 Pc
Billiard Ball
1 Set
Chalk
2 Pcs
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
4
2 Pcs
Leg
Main Metal Beam
2 Pcs 2 Pcs
End Slat
2 Pcs
Middle Slat
2 Pcs
End Play Bed Middle Play Bed
1 Pc 2 Pcs
Side Top Rail
2 Pcs
End Top Rail
2 Pcs
Side Apron
2 Pcs
End Apron
4 Pcs
Corner Post
4 Pcs
Main Beam End Board
8 Pcs
Shim
4 Pcs
Corner Cap
P15 P16
2 Pcs
Side Pocket
4 Pcs
Corner Pocket
All Right Reserved.
4 Pcs
Leg Leveler
P17
use deck of cards for shimming
(not included)

STEP 1:
5
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
Thread P17 Leg Levelers into P1 Leg as shown in Figure 1.
P17
P1
P17
Figure 1
All Right Reserved.
PARTS REQUIRED:
2 pcs - P1 Leg
4 pcs - P17 Leg Leveler
Note: Remove Parts Box, Leg Levelers
and Plastic Pockets from inside
Legs.

SAME
DIMENSION
P4
P4
6
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
STEP 2:
Attach each P2 Main Metal Beam to P1 Leg assembly as shown Figure 2 using H1 Bolts,H3 Washers,
H2 Spring Washers and H4 Hex Nuts. Use the T4 Wrench to assemble the hardware. Do not tighten
hardware at this time. Place P3 End Slats and P4 Middle Slats across P2 Main Beams and attach
using an H5 Bolts, H3 washers, H2 Spring Washers and H4 Hex Nuts. Attach the P5 Metal Beam End
Boards using H6 Screws.
H6
H2
P3 H1
H3
H4
P4
P4
P2
H4 H2
H1
H3
STEP 3:
Square up P4 Slats by measuring diagonally as show in Figure 3. Diagonal measurements should be
the same within 1/8". If the frame is not square, adjustment can be made by moving table beams P2 in
opposite directions. Once the frame is square, tighten all hardware.
Figure 2
Figure 3
All Right Reserved.
H3
H3
PARTS REQUIRED:
8 pcs - H1 Bolt
16 pcs - H2 Spring Washer
32 pcs - H3 Washer
16 pcs - H4 Hex Nut
8 pcs - H5 Bolt
8 pcs - H6 Screw
2 pcs - P2 Main Metal Beam
2 pcs - P3 End Slat
2 pcs - P4 Middle Slat
4 pcs - P5 Main Beam End Board
1 set - T4 Wrench
P2
P2
H5
H3
H4
H3
H2
P3
IMPORTANT NOTE:
Make sure holes are located on the
top of both P2 Main Metal Beams.
P5
Note: P5 Main Beam End Boards must be flush
or slightly lower than top of P3 End Slats.

STEP 4:
Use a carpenter’s level to level table as close as possible. It is easier to do it now rather than
after the Play Bed is on the frame.To determine the highest corner of the frame place the
level in following two positions.First check the table from end to end as shown in Figure 4.
Then check the table at an angle as shown in Figure 5.
7
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
Figure 4
Figure 5
All Right Reserved.

8
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
Figure 8
All Right Reserved.
UNBOXING THE SLATE (Slate tables only:)
! !
CAUTION AFTER CRATE PARTS ARE REMOVED, BEND NAILS OR STAPLES OVER WITH A
HAMMER AT ONCE! USE CAUTION WHEN HANDLING CRATE PARTS!
It is now time to uncrate the slate pieces.
With a claw hammer or crow bar, pry off crate
top at the notched corner. (See )
Remove the front rail of the crate. Slide the slate
out the front of the crate.
FIGURE 6
BE CAREFUL NOT TO DAMAGE SLATE
INSIDE! SLATE IS BRITTLE AND CAN
BE EASILY DAMAGED IF HIT OR PRIED
AGAINST!
(FIGURE 7)
UNBOXING THE SLATRON (Slatron tables only:)
It is now time to unbox the slatron pieces.
BE CAREFUL NOT TO DAMAGE SLATRON
INSIDE! SLATRON CAN BE EASILY DAMA-
GED IF HIT OR PRIED AGAINST!
(See FIGURE 8)
If the edges of your Slatron has “fuzz” on it,
lightly sand to remove with sandpaper
provided in the playbed kit.
IMPORTANT!
The sheets of slatron may not be completely flat when
removed from the shipping carton. This is normal. Once
they have been placed on the table frame and securely
fastened down, they will become straight and flat.
Figure 6
Figure 7

THE FOLLOWING STEP REQUIRES
THE HELP OF ANOTHER ADULT!
STEP 5:
You can tell the top side of the playfield sections by the beveled edge of the pocket openings
and the countersunk mounting holes. The beveled edges and the countersunk holes must
face up. (See Detail A)
much as you can. The playfield sections are 51 inches wide. The P4 Middle Slats are 51 inches
long, The play bed sections should be flush with the P4 Middle Slats on both sides of
table.
This step requires two adults!WARNING:
REMEMBER: Be sure countersunk holes in the playfield face up!
B) Secure center section P7 to long slats P4 with screws H7 into countersunk holes.
important that the edges of the three pieces ofplayfield are flush and square.
DO NOT OVER TIGHTEN SCREWS!
Place end Play Bed section P6 onto slats.Besure they are square,in line and butted up
tight
against center section P7.Secure end section P6 to beams using screws H7 into
countersunk holes.DO NOT OVER TIGHTEN SCREWS. NOTE:If necessary,shim underneath
TOP OF PLAY BED MUST BE PRECISELY LEVEL! EDGES MUST BE EVEN WITH ONE
ANOTHER!
Be sure that the side
of the table top
sections with the
countersink around
each hole face up
Detail A
9
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
H7
H7
H7
H7
H7
H7
P6
P7
P6
P4
P4
A) Place center section P7 on the two long slats P4.If edges do not align exactly,center playfield as
Note:It is
Play Bed where they join together to obtain a smooth,even surface.Shims are provided in the slate
bed kit.
Figure 9
H7
H7
PARTS REQUIRED:
16 pcs - H7 Screw
2 pcs - P6 End Play Bed
1 pcs - P7 Middle Play Bed
All Right Reserved.
Playbed sections must be flush with
P4 Middle Slats on both side of table.

SHIMMING INSTRUCTIONS
General Rules
Accomplish the leveling of the playing surface with
as few shims as possible.
Do not tap with a hammer or tighten screws
unreasonably tight. You will not be able to compress
the playing surface. You must shim up the playing
surface to level. Shims are meant only to raise the
low places at the seams and ends. Very short and
low places should be grouted. Do not assume the
floor is level. Most leveling can be accomplished by
working with the frame.
If using power tools be sure to use only enough
torque to reasonably tighten screws.
Seams can best be checked by passing your finger
over the seam and feeling if it is flush.
All screws must be tightened after shimming.
No two sets of Play Bed are exactly alike. Some
sets require more or less shimming than others.
Shim
Top of playing surface
must be flush at seams!
STEP BY STEP SHIMMING
A) Be sure table is set in its final location.
B) Table must be as level as possible before shimming. Large differences in levelness must
be corrected by raising or lowering frame with included leg levelers or shim stock
C) Tighten down all the playing surface mounting screws.
D) Check with a carpenter’s level to determine where playfield is low on ends, and use finger
tips to locate uneven spots at the seams. Loosen screws at these points and see if
playfield comes up to flush. If so, detach individual shims from the sheet shipped with this
table and place under these areas.
E) Lay a straight edge across seams to be sure playfield pieces are at the same height.
F) After top surface of playfield is flat and level, all screws must be snugged down in tight
position. Check these screws before proceeding to
the next step.
.
DO NOT ASSUME FLOOR IS LEVEL!
Place shims next to screws.
DO NOT OVER-TIGHTEN SCREWS!
GROUTING INSTRUCTIONS FOR PLAY BED
-
-
-
-
-
Clean top of playfield with a damp cloth. Allow enough time for
top sections to dry thoroughly before starting the next step.
Asmall container of grout has been provided for filling countersinks and small imperfections in the
table seams. Empty 1/3 of grout into a mixing container. Add 1 teaspoon of water and stir-add very
small quantities of grout or water to achieve a thick paste. When mixed, grout should be a thick
paste that will not drip off putty knife. If you do get grout too thin, slowly add more powder.
Using a putty knife, fill both seams and the four countersunk holes in the center playfield area.
(Only the four countersunk holes in the center of the table need to be filled since the other holes
will be covered by the rails.) Do not use more grout than you need.
Let grout dry. Read the rest of this manual while you wait!
Using a medium grit sandpaper and sanding block, sand the filled areas smooth and flat.
Re-grout if you still find low places
at countersunk holes or seams.
DO NOT USE TOO MUCH WATER!
RECHECK THESE AREAS TO MAKE SURE THEY ARE FLAT.
10
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
P8
All Right Reserved.
( use deck of cards for shimming, not included )
( use deck of cards for shimming, not included )

!!
WARNING
DO NOT SMOKE WHILE WORKING
WITH CONTACT CEMENT! READ LABEL
ON CEMENT CONTAINER CAREFULLY!
Applying the cloth:
1. Make sure Play Bed is dry and free of dust.
Before spraying adhesive, cut a portion of the shipping
carton to use as a shield to prevent cement over spray.
2. Place cloth over Play Bed with equal overhang on all sides.
3. Fold cloth away from end to expose Play Bed for your first
glue application. Apply contact cement to top surface in a band
4inches wide on this end. (See
Spray cement smoothly and evenly. Allow cement to become
tacky, wait at least one minute.
4. Fold cloth back over the table. With firm even pressure, press
cloth onto the area that has been coated with cement. Smooth
cloth down and over edges.
5. Fold cloth away from side to expose Play Bed for your se-
cond glue application. (See ). Apply cement to the
side in the same manner as your first glue application. Allow
cement to become tacky, wait at least one minute.
6. Fold cloth back over table. With firm even pressure, press
cloth onto the area that has been coated with cement. Smooth
cloth down and over edges.
7. Fold cloth away from other side to expose Play Bed for your
third glue application. (See ). Apply cement to this
side in the same manner. Allow cement to become tacky, wait
at least one minute.
8. Stretch the cloth across the width and over the edge of the table.
9. Fold cloth away from other end to expose Play Bed for your
fourth glue application. (See ) Apply cement to this
end in the same manner. Allow cement to become tacky, wait at
least one minute.
10. Make a final stretch along the length of and over the edge of
the table, stretch hard enough to work out all wrinkles. (See
) If cloth is not smooth, lift and re-apply.
Rubbing fingers lightly across cloth should not make
cloth move.
11. Locate center of pocket opening. (See and ) Using
sharp scissors, make a straight cut. Next, cut to pocket edge
to form pie shapes. (See ) Divide these pie shapes in
half. As you do, the pie shapes begin to relax to allow for
placement. You may need to make additional cuts.
12. Spray adhesive on the underneath side of the play-bed around
pocket face to adhere the cloth. Make sure not to get over spray
of glue on table. Allow cement to become tacky, wait at least
one minute. Stretch the pie shapes down and under the pocket
opening. Press the cloth against the cement on the underside
of the Play Bed. Be sure entire pie shape is fully attached
to underneath side of table.
NOTE:
NOTE: Cloth may seem small but it will stretch a great deal.
FIGURE 10) Coat edge also.
FIGURE 11
FIGURE 12
STRETCH HARD ENOUGH TO TAKE OUT WRINKLES, BUT
NOT SO HARD THAT THE CLOTH SLIPS.
FIGURE 13
FIGURE 14
NOTE:
Detail A B
detail B
First Glue
Application
Spray glue on
edge of slate too.
Second Glue
Application
Third Glue
Application FIRST
STRETCH
Fourth Glue
Application
FINAL
STRETCH
Cut with scissors.
Cloth should cover
pocket edges.
CENTER
CUT
DIVIDE
IN HALF DIVIDE
IN HALF
CUT TO
POCKET
EDGES CU T TO
POCKET
EDGES
Detail B
Detail A
DO NOT
CUT ANY
CLOSER
THAN 3/4”
11
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
All Right Reserved.

STEP 6:
P9
P10
NOTE:
All parts are
upside down
H8
P11
NOTE:
Edge of Rail and
Edge of Corner Cap
must be flush.
On a clean level surface, lay each P9 Side Top Rail and P10 End Top Rail face down as shown in
Figure 15.Next,lay each P11 Corner Cap face down and attach using H8 Screws (see inset) .
12
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
PARTS REQUIRED:
24 pcs - H8 Screw
2 pcs - P9 Side Top Rail
2 pcs - P10 End Top Rail
4 pcs - P11 Corner Cap
Figure 15
All Right Reserved.

13
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
All Right Reserved.
STEP 7:
With the rail assembly face down, place a P13 End Apron flush against the bottom of the P10 End
Top Rail and align using threaded inserts on the underside of each rail. Attach the end apron as
shown using H9 Bolts with H10 washers (see inset). Do not tighten yet. Attach opposite P13 End
Apron. Do not tighten yet.
Next, slide each P14 Corner Post over the edge of each P13 End Apron. Do not attach the Corner
Post yet. Next, slide one P12 Side Apron into the Corner Post, hold flush against the rail and attach
all aprons to top rails using H9 Bolts with H10 Washers. Do not tighten yet. Be sure each P14 Corner
Post is flush with each apron, then attach using H11 Screws. Lastly, tighten all H9 Apron Bolts.
Figure 16
H9
H10
H11 P13
P12
P14
P13
P12
PARTS REQUIRED:
12 pcs - H9 Bolt
12 pcs - H10 Washer
24 pcs - H11 Screw
2 pcs - P12 Side Apron
2 pcs - P13 End Apron
4 pcs - P14 Corner Post
Note:
Be sure each corner
post is flush with each
apron.

STEP 9:
14
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
With the help of three other adults, carefully rotate the rail and apron assembly and then place over the
play bed as shown. From the underside of the table, insert each H12 Bolts with H13 Washers up through
the play bed and into the threaded inserts of each rail. Be sure the rail assembly is aligned with the
play bed and pockets, then tighten all bolts.
H13
H12
H13
H12
Figure 17
PARTS REQUIRED:
18 pcs - H12 Bolt
18 pcs - H13 Washer
All Right Reserved.

STEP 10:
Insert the Corner and Side pockets into the drop pocket openings from the underside of the
table. Fasten pockets using four nails per pocket. Hold the nails with needle nose pliers and tap
them in with a small hammer. Once the nails have started into plastic pocket, hammer them completely
into the rails until heads are flush with plastic pockets. (See )
P15 P16
H14
Figure 18
15
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
H14
P15
P16
A5
A3
A6
A1
A2
Figure 18
All Right Reserved.
PARTS REQUIRED:
24 pcs - H14 Pocket Nail
4 pcs - P15 Corner Pocket
2 pcs - P16 Side Pocket
2 pcs - A1 Cue Stick
1 pcs - A2 Triangle
1 pcs - A3 Brush
1 set - A5 Billiard Ball
2 pcs - A6 Chalk

This customer warranty extends to the original owner, on the purchase of any ESCALADE SPORTS
Product (hereinafter referred as the "Product").
This Product is warranted to the original owner, for a period of 90 days from the
original purchase.
ESCALADE SPORTS warrants to the original owner, this product to be free
from defects in material and workmanship when used for the intended purpose under normal use and
conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED BY ACCIDENT,
UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS
PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL
AND WORKMANSHIP.
During the above 90 day warranty period, ESCALADE SPORTS shall
provide replacement components or replace with a comparable product at our choosing. If product is
defective under normal use and proper care, please contact our Customer Service Dept.
Other than shipping requirements no charge will be made for such replacement of in-warranty Products.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental
damages, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which
may vary from state to state.
WARRANTY DURATION:
WARRANTY COVERAGE:
WARRANTY REPLACEMENT:
LEGAL REMEDIES:
1-866-556-2757 / Customer Service Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706
Attn: Customer Service Dept.
Or E-mail us at:
[email protected]
ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE
ABOVE 90 DAY PERIOD. ESCALADE SPORTS SHALL NOT BE LIABLE FOR LOSS OF
USE OF THE PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS,
EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.
WARRANTY DISCLAIMERS:
90 DAY LIMITED WARRANTY
16
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
All Right Reserved.
Manufacturer warrants for five (5) years from the date of purchase for the Slatron™ and ten (10) years for
slate, Escalade Sports will repair the playing surface of this table, free of charge, if it fails to remain flat,
within a tolerance of + or – 30/1000 of an inch, measuring from any flat plane within the playing
surface. NOTE: Cloth not included in warranty. Should this product become defective due to material or
workmanship within period, contact the Customer Service Department. This warranty is not transferable
and does not cover normal wear and tear, or damage caused by improper handling, installation or use of
this product. This warranty is also void if product is in any way abused, damaged, or modified from its
original state, or if used for other than indoor residential use. This warranty gives the consumer specific
legal rights, and may have other rights which may vary from state to state.
WARRANTY ON SLATE/SLATRON™ SURFACE

P5223WWJH1
P5223WWJH2
P5223WWJH3
P5223WWJH4
P5223WWJH5
P5223WWJH6
P5223WWJH7
P5223WWJH8
P5223WWJH9
P5223WWJH10
P5223WWJH 11
P5223WWJH12
P5223WWJH13
P5223WWJH14
P5223WWJT 1
P5223WWJT2
P5223WWJT3
P5223WWJA1
P5223WWJA2
P5223WWJA3
P5223WWJA4
P5223WWJA5
P5223WWJA6
P5223WWJP1
P5223WWJP2
P5223WWJP3
P5223WWJP4
P5223WWJP5
P5223WWJP6
P5223WWJP7
P5223WWJP8
8
16
32
16
8
8
12
24
12
12
24
18
18
24
1
1
1
1
1
1
1
1
2
2
2
2
2
4
2
1
PART # KEY # DESCRIPTION QTY.
H1
H2
H3
H4
H5
H6
H7
H8
H9
H10
H11
H12
H13
H14
T1
T2
T3
A1
A2
A3
A4
A5
A6
P1
P2
P3
P4
P5
P6
P7
P8
PARTS LIST FOR MODEL # P5223W
17
©2012 Escalade Sports For Customer Service Call 1-866-556-2757
3/8"x2-1/4" Bolt
3/8" Spring Washer
3/8"x25mm Washer
3/8" Hex Nut
3/8"x3" Bolt
WP/4x1" Round Washer Head Screw
F5x1-3/4" Flat Head Screw
WP/3x18mm Round Washer Head Screw
5/16"x1-3/4" Bolt
5/16"x23 mm Washer
T4x15mm Round Head Screw
5/16"x1-1/2" Bolt
5/16"x32 mm Washer
Pocket Nail
Grout Kit
Spray Adhesive
Sand Paper
Cue Stick
Triangle
Brush
Table Cloth
Billiard Ball
Chalk
P5223WWJP9
P5223WWJP10
P5223WWJP11
P5223WWJP12
P5223WWJP13
P5223WWJP14
Hardware Kit
8
2
2
4
2
2
4
P9
P10
P11
P12
P13
P14
P5223WWJP15
P5223WWJP16
4
2
P15
P16
Leg
Main Metal Beam
End Slat
Middle Slat
Main Beam End Board
End Play Bed Slatron (P2000W)
Middle Play Bed Slatron (P2000W)
Shim
Side Top Rail
End Top Rail
Corner Cap
Side Apron
End Apron
Corner Post
Corner Pocket
Side Pocket
P5223WWJK1 1 K1
All Right Reserved.
Manual
P5223WWJM1 1 M1
P5223WWJP17 4 P17
Leg Leveler
P5223WWJT4 1 T4 Wrench
P5223WWJP6S 2 P6S
End Play Bed Slate (809-551)
P5223WWJP7S 1 P7S
Middle Play Bed Slate (809-551)