MobileDemand xTablet C1200 User manual

MobileDemand xTablet C1200
USER MANUAL

Table of Contents
C OPYRIGHT ................................................................................................ 4
REGULATORY S TATEMENT ................................................................................ 4
Federal Communications Commission Statement..........................................................................................................4
Declaration of Conformity ...............................................................................................................................................4
RF exposure warning........................................................................................................................................................5
European Notice ...............................................................................................................................................................5
R&TTE (CE) MANUAL REGULATORY REQUIREMENT (WLAN - IEEE 802.11b/g)..............................................5
Canadian Department of Communications.....................................................................................................................6
Battery Disposal................................................................................................................................................................6
CLASS 1 LASER PRODUCT...........................................................................................................................................6
SAFETY I NSTRUCTIONS .................................................................................. 7
BEFORE YOU START ................................................................ 9
PACKAGE C ONTENTS ..................................................................................... 9
FEATURES ............................................................................................... 10
C OMPONENTS ........................................................................................... 11
Front View.......................................................................................................................................................................11
Left View..........................................................................................................................................................................13
Right View........................................................................................................................................................................13
Back View........................................................................................................................................................................14
BottomView.....................................................................................................................................................................15
Status Indicators..............................................................................................................................................................16
GETTING STARTED ................................................................ 17
POWERING UP YOUR XTABLET
CONVERTIBLE..................................................................... 17
Connecting the AC Adapter............................................................................................................................................17
Using Battery Power.......................................................................................................................................................17
INSTALLING THE BATTERY ............................................................................. 18
Charging the Battery.......................................................................................................................................................18
Checking the Battery Level.............................................................................................................................................18
Removing the Battery......................................................................................................................................................19
STARTING YOUR XTABLET
CONVERTIBLE .......................................................................... 19
Using the Display Panel.................................................................................................................................................19
Turning On Your xTablet
Convertible.............................................................................................................................................20
Adjusting the LCD Panel Brightness.............................................................................................................................20
Changing the Display Orientation.................................................................................................................................21
Shutting DownYour xTablet
Convertible.......................................................................................................................................21
USING THE KEYBOARD................................................................................. 22
USING THE TOUCH PAD................................................................................ 23
USING THE STYLUS .................................................................................... 24
Calibrate the Screen........................................................................................................................................................24
USING THE QUICK MENU.............................................................................. 25

USING THE MEMORY C ARDS .......................................................................... 26
Inserting a Memory Card...............................................................................................................................................26
Removing a Memory Card.............................................................................................................................................26
USING THE 3G ANTENNAS ........................................................................... 27
MAKING CONNECTIONS ........................................................ 28
CONNECTING EXTERNAL DISPLAY D EVICES ......................................................... 28
Connecting a Projector or Display Monitor.................................................................................................................28
Connecting a TV .............................................................................................................................................................28
CONNECTING USB DEVICES.......................................................................... 29
CONNECTING H EADPHONES ........................................................................... 30
CONNECTING EXTERNAL M ICROPHONE .............................................................. 30
CONNECTING TO A LOCAL AREA NETWORK (LAN)................................................. 31
CONNECTING AN EXTERNAL SATA HDD............................................................ 31
CONNECTING TO WIRELESS C ONNECTIONS ......................................................... 32
Connecting to a Wireless Local Area Network..............................................................................................................32
Connecting to a Bluetooth Device .................................................................................................................................33
POWER MANAGEMENT .......................................................... 34
USING THE POWER P LAN .............................................................................. 34
USING THE POWER SAVING M ODE ................................................................... 35
USING THE BIOS SETUP UTILITY.......................................... 36
BIOS SETUP MENU.................................................................................... 36
STARTING THE BIOS SETUP U TILITY ................................................................ 36
NAVIGATING AND ENTERING INFORMATION IN BIOS.............................................. 36
MAIN M ENU ............................................................................................. 37
ADVANCED MENU ...................................................................................... 37
BOOT MENU............................................................................................. 38
SECURITY MENU........................................................................................ 38
SAVE & EXIT M ENU .................................................................................... 39
MOBILEDEMAND XTABLET C1200 DATAGUARD
SOFTWARE.................................... 40
USING MOBILEDEMAND XTABLET C1200
D ATA G UARD ...................................................................... 40
Creating NewTasks.........................................................................................................................................................44
Running the Mirror Backup ...........................................................................................................................................45
Deleting Tasks.................................................................................................................................................................45
Using Tools......................................................................................................................................................................47
TROUBLESHOOTING.............................................................. 48
SPECIFICATIONS .................................................................. 49

Preface
4
Copyright
Copyright© 2011. All rights reserved.
No part of this user manual may be transmitted, stored in a retrieval system, or
translated into any language or computer language, in any form or by any
means, without the prior written permission of the manufacturer. Information is
subject to change without prior notice.
Regulatory Statement
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and shielded AC power cable must be
employed
with this equipment to insure compliance with the pertinent RF emission limits
governing this device. Changes or modifications not expressly approved by the
system's manufacturer could void the user's authority to operate the equipment.
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the
following conditions:
This device may not cause harmful interference
This device must accept any interference received, including
interference that may cause undesired operation.

Preface
5
RF exposure warning
This equipment must be installed and operated in accordance with provided
instructions and must not be co-located or operating in conjunction with any
other antenna or transmitter. End-users and installers must be provided with
antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance.
SAR Value: 0.150 W/kg
European Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC)
and the Low Voltage Directive (73/23/EEC) issued by the Commission of the
European Community.
Compliance with these directives implies conformity to the following European
Norms:
EN 55022 ( CISPR 22 ) Radio Frequency Interference
EN 55024 ( EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-
5, EN61000-4-6, EN61000-4-8,EN61000-4-11, EN61000-3-2,
EN61000-3-3 )
Generic Immunity Standard
EN 60950-1 ( IEC 60950-1 ) Product Safety
R&TTE (CE) MANUAL REGULATORY REQUIREMENT (WLAN - IEEE
802.11b/g)
802.11b Restrictions:
European standards dictate maximum radiated transmit power of
100mW EIRP and frequency range 2.400-2.4835GHz.
In France, the equipment must be restricted to the 2.4465-
2.4835GHz frequency range and must be restricted to indoor use.
CE Declaration of Conformity
CE!
Is herewith confirmed to comply with the requirements set out in the Council
Directive on the Approximation of the Laws of the Member States relating to
Electromagnetic Compatibility (89/336/EEC), Low-voltage Directive
(73/23/EEC) and the Amendment Directive (93/68/EEC), the procedures
given in European Council Directive 99/5/EC and 89/3360EEC.
The equipment was passed. The test was performed according to the
following European standards.
EN 300 328 V1.7.1 (2006-05)
EN 301 489-1 V.1.4.1 (2005-09) / EN 301 489-17 V.1.2.1 (2002-04)
EN 60950-1:2006

Preface
6
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian
Interference-causing Equipment Regulations.
Battery Disposal
THIS PRODUCT CONTAINS A LITHIUM-ION OR NICKEL-METAL HYDRIDE
BATTERY. IT MUST BE DISPOSED OF PROPERLY. CONTACT LOCAL
ENVIRONMENTAL AGENCIES FOR INFORMATION ON RECYCLING AND
DISPOSAL PLANS IN YOUR AREA.
CLASS 1 LASER PRODUCT
LASERSCHUTZKLASSE 1 PRODUKT TO EN60825
CAUTION: THIS APPLIANCE CONTAINS A LASER SYSTEM AND IS
CLASSIFIED AS A "CLASS 1 LASER PRODUCT.”TO USE THIS
MODEL PROPERLY, READ THE INSTRUCTION MANUAL
CAREFULLY AND KEEP THIS MANUAL FOR FUTURE REFERENCE.
IN CASE OF ANY TROUBLE WITH THIS MODEL, PLEASE CONTACT
YOUR NEAREST "AUTHORIZED SERVICE STATION.”TO PREVENT
DIRECT EXPOSURE TO THE LASER BEAM, DO NOT TRY TO OPEN
THIS ENCLOSURE.
ANNEX IV
Symbol for the marking of electrical and electronic equipment
The symbol indicating separate collection for electrical and electronic equipment
consists of the crossed-out wheeled bin, as shown below. The symbol must be
printed visibly, legibly and indelibly.

Preface
7
Safety Instructions
DO NOT block the opening vents provided for ventilation.
Blocking these vents may cause the xTablet Convertible
processor to overheat.
Always keep strong magnetic or electrical objects away from your
xTablet Convertible.
DO NOT use or store your xTablet Convertible in extreme
temperatures. DO NOT place your xTablet Convertible near fire
or other sources of heat. DO NOT expose to dust or corrosive
materials.
DO NOT tamper the battery. Keep it away from children.
Never pick up or hold your xTablet Convertible by
the display.
DO NOT expose your xTablet Convertible to sudden changes in
temperature or humidity. Keep your xTablet Convertible away
from air conditioners or heating vents.

Preface
8
DO NOT attempt to service your xTablet Convertible yourself.
Any attempt to do so will make the warranty invalid.
When servicing, refer to qualified service personnel.
For better environmental protection, waste batteries should be
collected separately for recycling or special disposal.
CAUTION FOR ADAPTER
THIS XTABLET CONVERTIBLE IS FOR USE WITH DEDICATED AC ADAPTER.
BATTERY SAFETY
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE
MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE
MANUFACTURER'S INSTRUCTIONS.

9
Before You Start
Before You Start
Congratulations on your purchase of this xTablet Convertible.
This business xTablet Convertible is portable and suits a wide-range of user
requirements, providing users with maximum computing experience. Before you
begin using your xTablet Convertible, read this chapter to familiarize yourself
with the main components installed in the system.
Package Contents
The following items come with your package. If any of them is damaged or
missing, please contact your retailer.
xTablet Convertible Power adapter
Utility DVD Power cord
NOTE
• The pictures are for reference only, actual items may slightly differ.

10
Before You Start
Features
• Intel HM55 platform
• Operating system supports Microsoft® Windows 7
• 12.1”convertible LCD display
• High capacity hard disk drive
• Light weight
• Spill Proof
• Intel WLAN capability
• Bluetooth connectivity
• WWAN
• Express card slot
• Optional Solid State Primary Drive (SSD)
• Optional GobiTM 2000 3G and GPS

11
Before You Start
Components
Front View
No.
Item
Description
1
Camera
Use to take picture, record videos, or video
conference.
2
Display panel
Provides visual output.
3
Fingerprint scanner
Scans fingerprints for biometric identification.

12
Before You Start
No.
Item
Description
4
Brightness control
button
Press to increase the LCD panel brightness by one
level.
5
Brightness control
button
Press to decrease the LCD panel brightness by one
level.
6
SAS button
Press to exit Windows and switch to Standby
mode.
7
Power button
Press to turn your xTablet Convertible on or off.
8
Quick menu button
Press to access the quick menu.
9
LCD direction button
Press to rotate the screen orientation.
10
Program button
Press to start playback of chosen program.
11
Stealth mode button
Press to disable all emitting lights and sound.
12
Status Indicators
(Power, Wireless,
HDD, Caps Lock,
Num lock, Battery)
Indicates the corresponding function status.
13
Keyboard
Press the keys to input information.
14
Touch pad
Use to point, select, drag, or scroll objects on the
screen.
15
Touch pad button
Press to select objects or display a shortcut menu.
16
Chassis latch
Locks the xTablet Convertible chassis.
17
Handle
Use for carrying the xTablet Convertible around on-
the-go.

13
Before You Start
Left View
No.
Item
Description
1
USB port
Connects USB peripheral devices.
2
Card reader
Use to insert memory cards to transfer pictures,
music, and data between your xTablet Convertible
and flash compatible devices. The card reader
supports SD (Secure Digital), SDHC, Mini-SD
(with adapter), cards.
3
eSATA/USB Combo
port
Connects an external hard disc drive using an
eSATA cable for faster data transfer, or a USB cable
for USB peripheral devices.
4
ExpressCard slot and
PC Card slot
Use to insert one 34/54 ExpressCard or Type II PC
Card.
5
Microphone jack
Connects an external microphone.
6
Headphone jack
Connects headphones or external speakers.
Right View
No.
Item
Description
1
USB port
Connects USB peripheral devices.
2
Serial port (RS232)
Connects a peripheral device, such as a printer or
other device with serial port.
3
USB port
Connects USB peripheral devices.

14
Before You Start
Back View
No.
Item
Description
1
Kensington lock slot
Connects to a Kensington-compatible xTablet
Convertible security lock.
2
VGA port
Connects to a display device. (e.g. external
monitor, LCD projector).
3
LAN (RJ-45) port
Connects to a local area network (LAN) using an
Ethernet cable.
4
DC-in jack
Connects the power adapter.

15
Before You Start
Bottom View
No.
Item
Description
1
Docking station port*
Connects the xTablet Convertible to a docking
station.
2
Modular I/O port
bays
Use for user changeable modular I/O bay to
accommodate various devices applications.
3
Cooling vents
Use for air convection. Do not cover the cooling
vents to protect your xTablet Convertible from
overheating.
4
Stylus
Use for accurate control input to the LCD touch
panel and digitizer.
5
Battery compartment
Contains the battery.
6
Battery latch
Locks the battery in place.
7
Hard disk drive
(HDD) compartment
Contains the hard disk drive.
8
HDD latches
Locks the HDD in place.
*Docking station port function might not work on your system. Please check
with your dealer for more details.

16
Before You Start
Status Indicators
The status indicators in the upper left corner of the keyboard light up when a
particular function of the xTablet Convertible is active. Each indicator is
marked with a symbol.
Icon
Item
Description
Power indicator
The LED always lights on (blue) when the
system is running. When the system is in sleep
mode, the LED will blink.
WLAN
Indicates the status of wireless LAN
communication.
HDD
A blinking HDD LED indicates HDD activity (data
is being read or written).
Num Lock
Lights on when Num Lock is activated.
Caps Lock
Lights on when Caps Lock is activated.
Battery
Indicates the battery status:
• Green light means the battery is fully charged.
• Orange light means the battery is being
charged.
• Blinking red light means the battery power is
low.

17
Getting Started
Getting Started
This chapter will guide you on how to use your xTablet Convertible.
Powering Up Your xTablet
Convertible
Your xTablet Convertible can be powered up using the AC adapter or the
Lithium-ion battery.
Connecting the AC Adapter
The AC adapter powers up your xTablet Convertible and charges the battery.
1. Connect the AC adapter to the DC-in jack of your xTablet Convertible.
2. Connect the AC adapter to the power cord.
3. Plug the power cord to an electrical outlet.
Using Battery Power
1. Install a charged battery in the battery compartment.
2. Remove the AC adapter (if plugged). Your xTablet Convertible will
automatically use the battery power.
NOTE
• If your xTablet Convertible is connected to an electrical outlet and the

18
Getting Started
battery is installed, your xTablet Convertible uses power from the
electrical outlet.

19
Getting Started
Installing the Battery
To install the battery, follow the steps below:
1. Slide and hold the battery latch to the unlock
position.
2. Align and insert the battery to the battery
compartment.
3. Push completely until the battery locks into place.
4. Release the latch to the lock position to secure the
battery.
Charging the Battery
The Lithium-ion battery is not fully-charged upon purchase.
To charge the battery, follow the steps below:
1. Install the battery to your xTablet Convertible. See procedures above.
2. Connect the AC adapter to the DC-in jack of your xTablet Convertible.
3. Connect the AC adapter to the power cord.
4. Plug the power cord to an electrical outlet.
NOTE
• The charging time may be longer if you are using your xTablet
Convertible while charging the battery.
CAUTION
• DO NOT charge the battery if the temperature is below 0ºC or higher than
50ºC.
• Use only the supplied AC adapter. Using other AC adapters may damage the
battery or your xTablet Convertible.
Checking the Battery Level
The Battery LED flashes red when the battery is nearly depleted.
When this happens, save your work and plug the AC adapter to charge the
battery or replace the battery with a fully charged one.
NOTE
• Make sure the system has shut down before you change the battery.

20
Getting Started
Removing the Battery
To remove the battery, follow the steps below:
1. Slide and hold the battery latch to the unlock
position.
2. Remove the battery out of the battery compartment.
Starting Your xTablet Convertible
Using the Display Panel
•To open the display panel, unlock the chassis
latch to open the xTablet Convertible chassis.
Lift the cover lid up to upright position.
•To adjust the LCD panel, twist the LCD panel
according to your preference.