MobileDemand xTablet T1175 User manual

1
User Manual
xTablet T1175
1501 Boyson Square Drive – Suite 101 Hiawatha, Iowa 52233 | PH: 319.363.4121 | RuggedTabletPC.com

xTablet T1110
2
User Manual
xTablet T1175
Contents
Copyright and Trademark Notice 3
FCC Information 4
IC Statements 5
Safety Instructions 6
Introduction 8
Product Overview 9
Specications 13
Power Supply 14
Battery 15

xTablet T1175
3
Copyright and Trademarks Notice
All marks and names mentioned may be trademarks of their respective owners. No warranty as to
accuracy or completeness is expressed or implied. We reserve the right to make changes to this
document without prior notice.
Revision History
►Version: 1.0
►Date: 10, 2023

xTablet T1175
4
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and radiates radio frequency energy, and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
►Reorient or relocate the receiving antenna.
►Increase the separation between the equipment and receiver.
►Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
►Consult the dealer or an experienced radio TV technician for help.
NOTE
►The changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
►Shield interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
►This device may not cause harmful interference.
►This device must accept any interference received, including interference that may cause undesired operation.
FCC/IC RF Radiation Exposure and SAR Statements
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device was
tested for typical lap held operations with the device contacted directly to the human body to the back side of the notebook
computer. To maintain compliance with FCC RF exposure compliance requirements, avoid direct contact to the transmitting
antenna during transmitting SAR information 1.318W/Kg@1g (body).
Prohibit operating transmitters in the 5.925-7.125 GHz frequency band to control or communicate with unmanned aerial
vehicle systems.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme aux CNR exempts de licence d’Industrie Canada. Le fonctionnement est soumis aux deux
conditions suivantes:
(1) Cet dispositif ne peut causer des interférences; et
(2) Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement
de l’appareil.

5
CE Conformity
This device is in compliance with the essential safety requirements and other relevant provisions
set out in the European Directive.
Battery Regulations
European Union: Batteries, battery packs, and accumulators should not be disposed of as unsorted
household waste. Please use the public collection system to return, recycle, or treat them in compli-
ance with the local regulations.
BSMI: For better environmental protection, waste batteries should be collected separately for
recycling or special disposal.
California, USA: The button cell battery may contain perchlorate material and requires special
handling when recycled or disposed of in California.
For further information please visit: http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
Safety Guideline for Using Lithium Battery
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type
recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s
instructions.
WEEE Statement
European Union: Under the European Union (“EU”) Directive on Waste Electrical and Electronic
Equipment, Directive 2002/96/EC, which takes effect on August 13, 2005, products of “electrical and
electronic equipment” cannot be discarded as municipal waste anymore and manufacturers of cov-
ered electronic equipment will be obligated to take back such products at the end of their useful life.
This equipment complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment. End user
must follow the specic operating instructions for satisfying RF exposure compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The device is
designed to meet the requirements for exposure to radio waves established by the Industry Canada. These requirements
set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during
product certication for using at the body is 1.318 W/kg.
Cet équipement est conforme aux limites d’exposition aux rayonnements d’industrie Canada établies pour un environnement
non contrôlé. L’utilisateur nal doit suivre les instructions d’utilisation spéciques pour satisfaire à la conformité à l’exposi-
tion aux RF.
Cet émetteur ne doit pas être co-implanté ou exploité conjointement avec toute autre antenne ou émetteur. L’appareil est
conçu pour répondre aux exigences d’exposition aux ondes radio établies par industrie Canada. Ces exigences xent une
limite de DAS de 1,6 W / kg en moyenne sur un gramme de tissu. La valeur DAS la plus élevée déclarée en vertu de cette
norme lors de la certication du produit pour une utilisation à la caisse est de 1.318 W / kg.

xTablet T1175
6
Read the safety instructions carefully and thoroughly. All cautions and warnings on the equipment or
user’s manual should be noted.
Keep this equipment away from humidity and high temperature.
The openings on the enclosure are used for air convection to prevent the equipment from overheating.
Do not cover the openings.
• Do not leave the equipment in an unconditioned environment with a storage temperature
above 60ºC (140ºF) or below -20ºC (-4ºF), which may damage the equipment.
• This unit should be operated under maximum ambient temperature of 50ºC (120ºF)
or under 60ºC (140ºF) for light loading applications..
Followings are requirements of battery storage:
1. Storage temperature up to 3 months should remain between -20º ~45ºC ;
Storage temperature of 3 months to 1 year should remain between 23º± 2ºC.
2. The battery capacity should remain at 30 ± 5%.
3. The storage humidity should remain at 65 ± 25%RH.
4. The battery charging temperature 10º ~45ºC , discharging temperature -20º ~60ºC.
5. For the maximum battery discharging performance, storage temperature = 25ºC.
6. Do not charge the battery while the room temperature is over 40ºC.
• Make sure the power voltage is within safety range and has been adjusted properly to the
value of 100~240V before connecting the equipment to the power outlet.
• Always unplug the AC power cord before installing any add-on card or module to the equipment.
• Always disconnect the AC power cord or uninstall the battery pack or switch off the wall socket
if the equipment would be left unused for a certain time to achieve zero energy consumption.
Safety Instructions

7
Place the power cord in a way that people are unlikely to step on it. Do not place anything on top of
the power cord.
Always keep strong magnetics or electrical objects away from the tablet.
To avoid damage or electrical shock never pour liquid into any opening.
If any of the following situations arise, have the equipment checked by a service personnel:
• The power cord or plug is damaged.
• Liquid has penetrated into the equipment.
• The equipment has been exposed to moisture.
• The equipment is no longer working properly.
• The equipment was dropped and damaged.
• The equipment has obvious signs of breakage.
Green Product Features
• Reduced energy consumption during use and stand-by
• Limited use of substances harmful to the environment and health
• Easily dismantled and recycled
• Reduced use of natural resources by encouraging recycling
• Extended product lifetime through easy upgrades
• Reduced solid waste production through take-back policy
Environmental Policy
• The product has been designed to enable proper reuse of parts and recycling and should not
be thrown away at its end of life.
• Users should contact the local authorized point of collection for recycling and disposing of
their end-of-life products.

xTablet T1175
8
Introduction
Congratulations on the purchase of MobileDemand’s rugged xTablet®T1175. Designed and tested to
meet our exacting standards ensures dependability and customer satisfaction.
Refer to this manual to guide you through the basic functions and features.
Unpacking
Unpack the shipping carton and check all items carefully. If any item is damaged or missing contact MobileDemand. Please
keep the box and packing materials in the event you need to ship the unit. The package should contain the following items:
• xTablet T1175
• Type-C/Power Delivery adapter and AC power cord
• Hand strap
• Brief case handle
• Stylus (optional)
• Stylus holder (optional)
• Quick Guide

9
Product Overview
Front View
2
1
1. Front Camera
2. Internal Microphone
3. Status LEDS
Power
• Green OFF: Power off /Hibernation
• Green ON: Power on
• Breathing Green: Standby /Sleep
Battery Status
• OFF: Battery is not charging
• Green ON: Battery is fully charged
• Orange ON: Battery is charging while system ON & OFF
• Blinking Orange (4Hz): Battery error.
• Blinking Orange (1Hz): Battery capacity is lower than 7%
4. Speaker
Support high quality sound.
3
4

xTablet T1175
10
1. Barcode Scanner (optional)
2. Power Button
►Before powering on the tablet PC for the very rst time, you must connect it with AC power.
►Press and hold the power button for 2 seconds to power on the tablet PC.
►Press and hold the power button for 8 seconds can shut down the tablet PC.
3. Volume
Top View
1. Dock Connector
Connect with external Docking station to increase more I/O functions.
Bottom View
1. USB 2.0 Type-C PD-IN Port
The USB 2.0 Type-C PD-IN port allows you to connect USB-interface peripheral devices, such as the
mouse, keyboard, modem, portable hard disk module, printer, etc, and optionally supports PowerDelivery
function with variable up to 100W power input and maximum 5V/3A or 5V/1.5A power output when AC
power is connected.
1
Right Side View
1
1 2 3

11
1. USB 3.1 Gen 2 Port (with DisplayPort function)
USB 3.1 Gen 2, the SuperSpeed USB 10Gbps, supports high-speed data transfer for the connected devices,
such as storage devices, hard drives, or video cameras.
The DisplayPort function supports external display connection.
2. USB 3.1 Gen 2 Port
USB 3.1 Gen 2, the SuperSpeed USB 10Gbps, supports high-speed data transfer for the connected devices,
such as storage devices, hard drives, or video cameras.
3. Headphone Jack
Used for connecting the speakers or headphones.
4. RJ-45 Connector
The Ethernet connector, with optionally supported transmitting rate of 10/100/1000 megabits per second, is
used to connect a LAN cable for network connection.
5. Kensington Lock
This tablet provides a Kensington lock hole, which allows users to secure the tablet in place.
21 3 4 5
Left Side View

xTablet T1175
12
6
1
2
5
3 4
1. F1 Button - Barcode Scanner Trigger
2. Battery Latch
This built-in rear camera can be used for photos, video recording, conferencing, and other interactive
applications.
3. Micro SD Card Slot
To access remove battery.
4. Nano Sim Card Slot
To access remove battery.
5. F2 Button - User Dened
6. Rear Camera
Back View

13
Specications
The specications listed here are for reference only, and may change without notice.
¹Battery life varies signicantly depending on settings, app usage, and other factors
I/O PORTS USB 3.1 Gen1 (Type A )
USB 3.1 Gen1 (Type C )
USB 2 Gen1 (Type C )
MicroSD Reader (micro)
SIM card slot (nano)
Headphone (3.5mm)
LAN Port
19 pin pogo
BUTTONS Power Button
Vol Up Button
Vol Down Button
Reset
Function (Fn) Keys - x2
SENSORS Accelerometer
Gyroscope
E-Compass
Proximity
Ambient Light
BATTERY
SYSTEM
7.6V, 8,340 mAH, 64Wh
Up to 10Hr battery life1
Hot swappable
WIRELESS/NETWORK
WLAN Intel AX211 802.11 a/b/g/n/ac/ax
Wi-Fi 6E
Bluetooth 5.3
GPS uBlox-M9N
LT E Optional 4G
RFID/NFC Optional 13.56MHz/125kHz
SECURITY
TPM 2.0
AGENCY APPR FCC, CE, IC, WEEE, RoHS
DIMENSIONS 11.54 in. L x 7.56 in. H x .67 in. D
293mm L x 192mm H x 17mm D
Weight - 1350g | 2.97lbs
DISPLAY 10.1” sunlight viewable
WUXGA 1920W x 1200H IPS; 800 NITS
10-point multi-touch capacitive screen.
Digitizer support MPP2.0/EETI
CPU Intel® 13th Gen i5-1335U
Optional i7 upgrade
MEMORY 16GB
STORAGE 256GB Standard, 512Gb/1TB Optional
PCIe SSD
O/S Windows 11 Pro
Optional: Windows 10 Pro Downgrade; LTSC
RUGGEDIZED MIL-STD-810G (5’ drop)
Sealing IP65 (dust and water)
Screen Protector Oleophobic, scratch-resistant glass
Operating Temp 14°F to +122°F / -10°C to +50°C
Storage Temp -4°F to +140°F / -20°C to +60°C)
Operating Humidity 5% to 95% RH, non-condensing
CAMERA Front - 2MP FF - Windows Hello support
Rear - 8MP AF with flash
AUDIO High Denition Audio
SCANNER Optional High performance
Honeywell N6703 2D barcode scanner
Honeywell N6803 2D barcode scanner

xTablet T1175
14
Getting Started
Power Supply
This section provides basic safety precautions when using an AC/DC adapter and battery.
AC/DC Adapter
Ensure the xTablet T1175 is connected to an AC power source via the AC adapter before turning it on
for the rst time. If the xTablet automatically shuts down due to low battery power, it is likely to cause
system failure. Below are some Dos and Don’ts for an AC/DC adapter.
►Dos
• Use the adapter that shipped with xTablet T1175 only.
• Always be aware of heat coming from the AC/DC adapter while in use.
• Unplug the AC power cord before disassembling the tablet.
►Don’ts
• Never cover an adapter that is in use as it can generate heat.
• Have the AC power cord plugged in after powering off the system when the tablet is going to be left unused for
a longer time.
Plug the AC/DC Adapter
• Plug the DC end into the USB-C Power Delivery (PD) port of the xTablet T1175.
• Plug the AC/DC adapter into the power outlet.
• When removing, follow steps in reverse order.
(NOTE: The interchangeable plug may vary depending on countries or regions.)

15
Battery
This Tablet is equipped with a built-in Lithium-ion Polymer battery pack.
The rechargeable Lithium-ion Polymer battery pack is an internal power source.
The battery pack may be damaged if users attempt to disassemble it. The limited warranty will be
voided if the battery pack is disassembled by non-authorized technicians. Please follow your local
laws and regulations to recycle the Tablet and the built-in battery pack.
►Conserving Battery Power
Efcient battery power is critical to maintain normal operation. If battery power is not managed well, the saved data
and customized settings may be lost.
To optimize battery life and avoid sudden power loss, read the tips below:
• Suspend system operation if the system will be idle for a period of time.
• Disable unnecessary settings or remove idle peripherals.
• Connect an AC/DC adapter to the system whenever possible.
►Charging the Battery Pack
The built-in battery pack can be recharged when the Tablet is connected to the AC power. Please pay attention to the
following tips before recharging the battery:
• You can use the system, suspend system operation or shut down and turn off the system without interrupting the
charging process.
• The built-in battery pack uses Lithium-ion Polymer battery cells that have no “memory effect.” It is unnecessary
to discharge the battery before recharging. However, to optimize the life of battery, we suggest that consuming the
battery power completely once a month is necessary.
• The actual charging time will be determined by the applications in use.

Contact our sales team today | [email protected] | 319.363.4121
1501 Boyson Square Drive | Suite 101 | Hiawatha, Iowa 52233 | RuggedTabletPC.com
©2023 MobileDemand, LC | All trademarks are property of their respective owners.
VERSION 12.11.23