Mobinil MF29A User manual

Connecting Your Device
Follow the numbers to connect your device.
NOTE:
• If you want to use the mobile network to connect to the Internet, you
needtoinsertyourSIMcardrst.
• Voice Calls Are Not Activated.
Normal states of the indicators are shown below.
Indicator State Description
WAN signal strength ON Signal strength is very good.
Network mode ON Blue: Registered to 3G network.
Red: Registered to 2G network.
WAN connection status OFF WAN connection not established
(PDP not activated).
Phone status 2 ( Voice
calls are not available in Egypt )
ON PSTN connected.
Phone status 1 ( Voice
calls are not available in Egypt )
OFF Local phone is on hook.
Wi-Fi ON WLAN works normal.
Power ON Switch on your device and the
power is normal.
External antenna area:
ANT The external antenna connectors.
PRESS
ANT ON
This button is only used for external antenna. If
you connect the external antenna, please press
it. Otherwise the RSSI signal of the router will be
poor, and your device may not access the Internet.
Conguring Your PC
Followthe followingsteps andgures forWindows XPtoconguretheIn-
ternet Protocol for your connection.
NOTES:
• WirelessNetworkConnectionisusedforWi-Ficonnection.
• LocalAreaConnectionisusedforNetworkCableconnection.
1. Right-click My Network Places, and then select Properties.
2. Right-click the icon for Connection, and then select Properties.
3. Select Internet Protocol(TCP/IP), and then click Properties.
4. Select these two items, and then click OKtonishtheconguration.
Accessing the Internet
Before accessing the Internet, please make sure:
• YourdeviceisconnectedvianetworkcableorWi-Fi.
• YourPCiscongured.
To access the Internet:
1. LogintheWebGUICongurationPage.
1) Launch the Internet browser and enter http://192.168.1.1 in the
address bar. The login page appears.
2) Input the password (the default password is admin), and then click
Login.
2. Select the Operation Mode.
NOTE: If you select the Bridge mode, you need to connect your clients to
the LAN ports via Ethernet cable, and use normal methods to surf directly
on your clients. If you want to use other operation mode after Bridge, you
need to restore your device.
3. ConguretheWAN Connection.
NOTE: This step is used for Cable Broadband mode and 3G Gateway
mode.
• For Cable Broadband
u Please select PPPoE, and input them.
NOTE: YourserviceprovidergivesyoutheUserNameandPassword.
u Please select Static and input all the parameters.
NOTE: Yourserviceprovidergivesyouthestaticaddressinformation.
u Please select DHCP.
NOTE: Yourserviceproviderdoesnotgiveyouanyparameters.
• For 3G Gateway
4. Begin to enjoy your Internet service.
Wireless Connection
If you want to use Wi-Fi to connect your router, please refer to the following
steps.
1. Make sure that the WLAN works normal. Please check the Wi-Fi Setting
ontheWebGUICongurationpageorchecktheWi-Fiindicator .

Others
Symptoms Possible Problems/ Solutions
The RSSI signal
indicator is al-
ways blinking or
does not light.
• This indicates poor reception. Try moving the router
to another location near the window.
• Check the ANT button to see if you have press the
ANT on but without connecting the external antenna.
About the pass-
word
• For the Wi-Fi connection password, please check
the label on the device.
• ThedefaultpasswordofthewebGUIconguration
page is admin.
• If you changed the password and forgot the new
password, you need to restore the device to the fac-
tory default settings.
For more assistance, please:
• SendE-mailto[email protected]
• Visithttp://www.zte.com.cn
• CallServiceHotline:[phone]
Warning and Notice
Safety Precautions
• Some electronic devices may be susceptible to electromagnetic
interference. Locate the router away from TV set, radio and other
electronic equipment to avoid electromagnetic interference.
• The router may interfere with medical devices like hearing aids and
pacemakers. Consult a physician or the manufacturer of the medical
device before using the router.
• Please keep yourself at least 20 centimeters away from router.
• Do not use your router in dangerous environments such as oil terminals
or chemical factories where there are explosive gases or explosive
products being processed.
• Please use original accessories or accessories that are authorized by
ZTE. Unauthorized accessories may affect the router performance,
damage the router or cause danger to you.
• Do not attempt to dismantle the router. There are no user serviceable
parts.
• Do not allow the router or accessories to come into contact with liquid or
moisture at any time. Do not immerse the router in any liquid.
• Do not place objects on top of the router. This may lead to overheating
of the device.
• The device must be placed in ventilation environment for use.
• Donotexposetheroutertodirectsunlight orstoreitinhotareas.High
temperature can shorten the life of electronic devices.
• Do not allow children to play with the router or charger.
• Keep the length of the cable between the router and the phone less
than 10 meters. ( Voice calls are not available in Egypt )
• The router is for indoor use only. Do not use the router outside. Do
not connect telephone extensions which run outside of the building.
These can result in lightning damage to your unit. ( Voice calls are not
available in Egypt )
Cleaning and Maintaining
• Use an antistatic cloth to clean the router. Do not use chemical or
abrasive cleanser as these could damage the plastic case. Turn off your
router before you clean it.
• Use the router within the temperature range of -10°C ~ +55°C, and the
storage temperature range is -20°C ~ +65°C. The humidity range is
5%~95%.
• Do not use your router during a thunderstorm. Remove the mains power
pack from the wall socket.
• Do not take out your (U)SIM card unnecessarily. The (U)SIM card may
be easily lost or it can be damaged by static electricity.
Limited Warranty
• This warranty does not apply to defects or errors in the Product caused
by:
i. Reasonable abrasion.
ii. End User’s failure to follow ZTE’s installation, operation or
maintenance instructions or procedures.
iii. End User ’s mishandling, misuse, negligence, or improper
installation, disassembly, storage, servicing or operation of the
Product.
iv. Modifications or repairs not made by ZTE or a ZTE-certified
individual.
v. Powerfailures,surges,re,ood,accidents,actionsofthirdparties
or other events outside ZTE’s reasonable control.
vi. Usage of third-party products, or usage in conjunction with third-
party products provided that such defects are due to the combined
usage.
vii. Any other cause beyond the range of normal usage intended for the
Product.
End User shall have no right to reject or return the Product, or receive a re-
fund for the Product from ZTE under the above-mentioned situations.
• This warranty is End User’s sole remedy and ZTE’s sole liability for
defective or nonconforming items, and is in lieu of all other warranties,
expressed, implied or statutory, including but not limited to the implied
warrantiesofmerchantabilityandtnessforaparticularpurpose,unless
otherwise required under the mandatory provisions of the law.
Limitation of Liability
ZTEshall notbe liablefor anyloss ofprots orindirect, special,incidental
or consequential damages resulting from or arising out of or in connection
with using of this product, whether or not ZTE had been advised, knew or
should have known of the possibility of such damages, including, but not
limitedtolostprots,interruptionofbusiness,costofcapital,costofsubsti-
tute facilities or product, or any downtime cost.
I hear a rapid engaged
tone as soon as I lift the
phone off the hook. ( Voice
calls are not available in
Egypt )
Put the phone on hook and try again. If you
are connected to the Internet using the 2G
(GSM)network,pleasedisconnectthisrst.
After dialing the last digit I
hear nothing /silence.
Whenyouhavenisheddialingyoucan
press the # key or wait 4-8 seconds to con-
nect the call.
I can’t make or receive a
callwhenIamsurngon
the net. ( Voice calls are
not available in Egypt )
If you are connected using the 2G (GSM)
network then you cannot surf the net and
make a phone call simultaneously. Please
disconnect the Internet and wait 30 seconds
to 1 minute before making a call.
Internet Related Problems
Symptoms Possible Problems/ Solutions
Can not access
the Internet at all.
• Pleasecheckyourcongurationsettings.
• Please wait 1~ 2 minutes for the router to initialize.
• Check your service indicator LED’s.
The download or
upload speeds
are very slow.
The speed is dependent on signal strength. Check
your signal strength and network type.
Can not visit the
webGUIcongu-
ration page
• Enter the correct address. The default address is
http://192.168.0.1.
• Only use one network adapter in your PC.
• Do not use any proxy server.
Can not establish
the Wi-Fi connec-
tion between your
device and client
• Make sure the Wi-Fi function is active. Press the
WPS button to enable Wi-Fi function.
• Refresh network list and select the correct SSID.
• Check the IP address to make sure your client can
obtain an IP address automatically in the Internet
protocol (TCP/IP) properties.
• Type the correct network key (Wi-Fi password)
when you connect to the device.
2. Use your normal Wi-Fi application on the client to search for the
available wireless networks.
NOTE: Please set the client to obtain an IP address automatically, and the
client will get an IP address like “192.168.0.101”.
3. Select the SSID of your device, and then click Connect.
NOTE: Please check the label on your device to get the default SSID and
Wi-Fi password.
4. Input the password, and then click Connect.
NOTE:
You may need to input the password for Wi-Fi connection. Please check
the label on your device to get the default.
5. Wait a moment, and then the client will connect to your device
successfully.
If you want to use WPS function to get the Wi-Fi connection, please:
1. Power on your device, and enable the Wi-Fi function on your device.
2. Enable WPS function. Please check the WPS Setting on the WebGUI
Congurationpage.
3. Press the WPS button on your device to start Wi-Fi Protected Setup
authentication process.
4. Enable the WPS function on your client to respond this authentication
process.
5. Followthesystempromptsonyourclienttonishtheconnection.
Troubleshooting
Voice Related Problems
Symptoms Possible Problems/ Solutions
No Dial Tone.
• Please wait for 1~2 minutes after the
router is turned on.
• If 3G LED light is blinking, you have no
good RF reception. Change the location
of the router.
There is a prompt/ phone
alert/ announcement as
soon as I lift the phone off
the hook. ( Voice calls are
not available in Egypt )
Make sure your (U)SIM card is inserted cor-
rectly and the PIN number has been entered.
If the PIN number has been entered incor-
rectly then you will need to enter the PUK
code when prompted.
The line is noisy/ distorted
when I lift the phone off the
hook. ( Voice calls are not
available in Egypt )
• Remove any electrical appliance which is
too close to the phone or router.
• The cable or phone set might be faulty.
ZTE CORPORATION
NO.55,Hi-techRoadSouth,ShenZhen,P.R.China
Postcode: 518057