Mobius M9 SORTER User manual

©2021 ETEROS TECHNOLOGIES INC. ALL RIGHTS RESERVED. | MOBIUSTRIMMER.COM
USER GUIDE
MOBIUS M9 AUTOFEED CONVEYOR

CONTENTS

This User Guide is a comprehensive manual covering the operation and maintenance of the Infeed
and Outfeed Conveyor machines as of the date of publication. ETEROS TECHNOLOGIES reserves the
right to make updates to the machine from time to time. In the event of an update, this User Guide
will remain appropriate for the safe operation and maintenance of your unit. This User Guide, as well
as any documentation supplied by component manufacturers, are to be considered the information
package associated with this device. Every operator must read and understand the User Guide. The
manual should be located within easy access for periodic review.
SAFETY INSTRUCTIONS
DISCLAIMER
WARNING LABELS
SERVICE & REPAIRS
GENERAL SAFETY PRECAUTIONS
5
5
6
6
7
SAFETY 4
GET TO KNOW YOUR CONVEYORS
WHAT'S IN THE CRATE
INITIAL ASSEMBLY & INSPECTION
9
10
11
INITIAL SETUP 8
GENERAL OPERATION
BEARING REPLACEMENTS
19
21
OPERATIONS 18
CLEANING THE CONVEYORS
PREVENTATIVE MAINTENANCE
SPECIFICATIONS
28
28
29
CLEANING & MAINTENANCE 27
NOTES:

SAFETY

5
SAFETY INSTRUCTIONS
To ensure operator safety while in use, this device includes decaling, guarding, and other safety features.
Operators are encouraged to use caution and best judgment when using equipment. Equipment
should be serviced when required.
To avoid possible damage to the machine and risk of injury to the operator, consult with an ETEROS
TECHNOLOGIES representative to answer any questions.
All operators must read and understand this User Guide and be trained in safe operation and use of the
M9 Autofeed Conveyor. We recommend the owner of this equipment develop a standard operating
procedure specic to each worksite to address any local hazards or other conditions not outlined in
this User Guide. The conveyor must be inspected regularly for damage, component failure and wear.
Results of inspection activity should be documented.
ETEROS TECHNOLOGIES makes every effort to ensure the M9 Autofeed is compliant with all current
safety standards. It is the responsibility of the owner to ensure all municipal, provincial, state, county,
territorial, and federal codes, regulations and standards have been met in each working location.
Do not lend or rent your machine without providing the User Guide. A rst-time operator should receive
practical instruction before using the machine.
This machine is not to be used for any purpose other than those expressly stated in the User Guide,
advertising literature, or other ETEROS TECHNOLOGIES written material pertaining to the conveyors.
DISCLAIMER
ETEROS TECHNOLOGIES recognizes that the Infeed and Outfeed Conveyors are purpose-built
machines for processing cannabis by licensed producers. Please check all municipal, provincial/
state, and federal laws and regulations before using the Infeed and Outfeed Conveyors. ETEROS
TECHNOLOGIES does not promote or condone the use of processing equipment in any way that may
be deemed illegal.
ETEROS TECHNOLOGIES recognizes that our equipment can be used for processing herbs, hops, owers
and many other products. It is not the responsibility of ETEROS TECHNOLOGIES to conrm alternative
applications for our equipment.
©2021 ETEROS TECHNOLOGIES INC. ALL RIGHTS RESERVED. | MOBIUSTRIMMER.COM

MOBIUS CONVEYOR USER GUIDE
6
WARNING LABELS
SERVICE & REPAIRS
Indicates a hazardous situation that, if not avoided, will result in serious
injury and / or death. This signal word is to be limited to the most extreme
situations; typically for machine components that, for functional
purposes, cannot be guarded.
Indicates a potentially hazardous situation that, if not avoided, could
result in serious injury and / or death. It includes hazards that are exposed
when guards are removed. It may also be used to alert against unsafe
practices.
Indicates a potentially hazardous situation that, if not avoided, may
result in minor or moderate injury. It may also be used to alert against
unsafe practices.
Repairs may only be carried out by Eteros Technologies or a designated authorized agent (service
technician).
Should the need arise, please notify us:
ETEROS TECHNOLOGIES
26 Industrial Ave.
Carleton Place, Ontario, Canada
K7C 3T2
www.eteros.com
Improper interfacing, improper repair, or unauthorized modication could result in void warranty claims.
CAUTION:
WARNING:
DANGER:

7
GENERAL SAFETY PRECAUTIONS
1. READ and become familiar with the entire User Guide. LEARN the equipment applications, limitations,
and possible hazards.
2. DO NOT USE THE DEVICE IN A DANGEROUS ENVIRONMENT or damp or wet locations. Never expose
the control panel directly to rain or water. Keep the work area well illuminated.
3. DO NOT use the device in the presence of ammable liquids or gases.
4. KEEP WORK AREA CLEAN. Cluttered areas and workspaces invite accidents.
5. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective
hair covering to contain long hair.
6. POWER DOWN AND DISCONNECT EQUIPMENT before washing, servicing and when changing
accessories.
7. CHECK FOR DAMAGED PARTS PRIOR TO OPERATION. The equipment should be inspected prior to
use to ensure proper operation in performing its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may
affect its operation. Any damaged part including guards should be properly repaired or replaced.
8. ALWAYS WEAR EYE PROTECTION.
©2021 ETEROS TECHNOLOGIES INC. ALL RIGHTS RESERVED. | MOBIUSTRIMMER.COM

INITIAL SETUP

9
GET TO KNOW YOUR CONVEYORS
©2021 ETEROS TECHNOLOGIES INC. ALL RIGHTS RESERVED. | MOBIUSTRIMMER.COM

MOBIUS CONVEYOR USER GUIDE
10
WHAT’S IN THE CRATE
1 x H-BASE
1 x TALL H-BASE
1 x SHORT H-BASE
2 x THROUGH STOPS
1 x CONTROL PANEL WITH TOOL STORAGE
4 x 2" HEX BOLTS
4 x NUTS
4 x WASHERS FOR HEX BOLTS
2 x 1" BUTTON HEAD SCREWS
6 x 3/8" BUTTON HEAD SCREWS
4 x 5/8" BUTTON HEAD SCREWS
2 x SIDE PANELS
2 x HOPPER HANDLES
6 x ACORN NUTS
1 x TENSIONING TOOL
2 x SUPPORT BAR
YOUR AUTOFEED CONVEYOR COMES WITH THE FOLLOWING ITEMS:

11
INITIAL ASSEMBLY & INSPECTION
1. Inspect the crate and crate contents to ensure no damage occurred during shipping.
2. Remove components from the crate.
3. Begin by installing the SHORT H-BASE UPRIGHT to the H-BASE by using 2 x 2” HEX BOLTS, 2 x WASHERS
and 2 x NUTS. The head of the bolts should sit within The head of the bolts should sit within The head
of the bolts should sit within the hexagonal cutouts on the H-BASE UPRIGHTS. Ensure that both pieces
are installed facing the same direction.
©2021 ETEROS TECHNOLOGIES INC. ALL RIGHTS RESERVED. | MOBIUSTRIMMER.COM

4. Install the TALL H-BASE UPRIGHT to the H-BASE using the same hardware in the last step.

13
©2021 ETEROS TECHNOLOGIES INC. ALL RIGHTS RESERVED. | MOBIUSTRIMMER.COM
5. Slide 2 x THROUGH SUPPORT BARS through the conveyor body. Then, slide 2 x THROUGH STOPS on
to the protruding ends of the THROUGH SUPPORT BARS. Ensure the lip on the THROUGH STOPS is ush
with the sheet metal. With the THROUGH STOPS installed, and with the help of another person, slide
the protruding bars into the SHORT H-BASE UPRIGHT and TALL H-BASE UPRIGHT and fasten with 2 x 1”
BUTTON HEAD SCREWS.

MOBIUS CONVEYOR USER GUIDE
14
©2021 ETEROS TECHNOLOGIES INC. ALL RIGHTS RESERVED. | MOBIUSTRIMMER.COM
6. Install the BELT onto the conveyor body by simply sliding it on to each end. Ensure the groove along
the underside of the BELT is aligned in the grooves on the rollers at each end of the conveyor.
Operation section. The CONTROL PANEL can also be placed on the mounting bar as shown.

7. Install a SIDE PANEL on each side of the conveyor by aligning the circular cutouts with the THROUGH
STOPS and THROUGH BARS. Simply slide each panel down onto the pucks to install it on the conveyor.

MOBIUS CONVEYOR USER GUIDE
16
©2021 ETEROS TECHNOLOGIES INC. ALL RIGHTS RESERVED. | MOBIUSTRIMMER.COM
8. Join the side panels to each other by installing the HOPPER HANDLES. Align a handle with the screw
hole cutouts on the side panels, and secure using 2 x ⅝” BUTTON HEAD SCREWS.

• Conrm the power cord is in good condition
• Ensure the belt is properly aligned on the rollers on each end
• Ensure the belt is properly tensioned
• Ensure all fasteners are tight and that there is no wobble in the frame
10. Using the TENSIONING TOOL, turn the BELT TENSIONING STUB to ensure that the belt is properly
tensioned. DO NOT OVER TORQUE THE BELT TENSIONING STUB, PERMANENT DAMAGE MAY RESULT.
The TENSIONING TOOL can be stored in the keyhole cutout on the CONTROL BOX.
11. Once initial assembly is complete, inspect the conveyors to conrm that they are ready to operate:
9. Finally, to complete the hopper assembly, install the BACK PLATE on to the outside of the side panels
by aligning the screw holes and securing with 6 x ⅜” BUTTON HEAD SCREWS. The screw heads should
go on the inside of the hopper, and the 6 x ACORN NUTS can be used on the outside to rmly secure
the BACK PLATE.

OPERATIONS

19
©2021 ETEROS TECHNOLOGIES INC. ALL RIGHTS RESERVED. | MOBIUSTRIMMER.COM
To remove the belt:
To re-install the belt:
For ease of use with other Mobius equipment, the orientation of the control panel can be reversed so
that it can be accessed from either side of the equipment. To switch the control panel:
1. Grab the handles on the HOPPER, and lift it off the conveyor.
2. While standing on the opposite side of the motor, use the TENSIONING TOOL to turn the BELT
TENSIONING STUB clockwise until signicant resistance is felt. DO NOT KEEP TURNING PAST THIS POINT.
3. Once there is enough slack in the belt, simply slide it off the side of the conveyor.
1. Slide the conveyor belt on to the metal body from the side of the machine.
2. Ensure the groove on the underside of the belt is positioned in the slots of the rollers at each end.
You’ll feel the belt “click” into place once positioned correctly.
3. Using the TENSIONING TOOL, turn the BELT TENSIONING STUB counterclockwise until the belt is
tensioned. When the belt is adequately tensioned, the BELT TENSIONING STUB will provide signicant
resistance against further turning. DO NOT TENSION THE BELT PAST THIS POINT. DO NOT USE A POWER
TOOL TO TENSION THE BELT. PERMANENT DAMAGE WILL RESULT.
1. Lift the CONTROL BOX off the CONTROL BOX MOUNTING BAR. No tools or fastener removal is required.
2. Rotate the CONTROL BOX so that it is facing the other side of the equipment, and place it down on
the CONTROL BOX MOUNTING BAR.
REMOVING AND INSTALLING CONVEYOR BELT
CONTROL PANEL ADJUSTMENT
GENERAL OPERATIONS

MOBIUS CONVEYOR USER GUIDE
20
LEFT = ON/OFF: turns the conveyor on or off. In the on position, the conveyor will immediately begin
running at the set speed and direction. In the off position, no power is delivered to the machine.
MIDDLE = SPEED CONTROL: rotate the knob clockwise to increase the belt speed, and rotate the knob
counterclockwise to reduce belt speed.
RIGHT = DIRECTION CONTROL: ipping the direction switch will change the travel direction of the belt
CONTROL PANEL OVERVIEW
MACHINE START UP SEQUENCE
1. Plug the power cord into an outlet.
2. Ensure belt is tensioned.
3. Ensure hopper is installed.
4. Flip the power switch to the ON position.
5. Flip the direction switch to set the conveyor to the correct travel direction.
6. Turn the speed adjustment knob clockwise to increase the belt speed, or counterclockwise to
reduce the belt speed.