Mobotix MX-Overvoltage-Protection-Box Instructions for use

EN
www.mobotix.com
Innovations – Made in Germany
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its
decentralized concept has made high-resolution video systems cost-ecient.
MOBOTIX AG • D-67722 Langmeil • Phone: [phone] • Fax: [phone] • [email protected]
Quick Install MX-Overvoltage-Protection-Box
Security-Vision-Systems
31.684-006_EN_07/2015
Surge Protection for
MOBOTIX IP Cameras
• Protects MOBOTIX cameras against surges of up to
4kV on the PoE network cabling
• For patch cable to patch cable or patch cable to
installation cable (MX-Overvoltage-Protection-Box-LSA)
• Complete set including mounting supplies
Weatherproof network connector (IP65) with surge
protection of up to 4 kV for MOBOTIX IP cameras;
ideal for replacing MX-Patch-Box
Surge Protection for MOBOTIX IP Cameras
Surges are voltages that exceed the allowed voltage range for MOBOTIX IP cameras. The max. voltage for
PoE, for example, is 57V. Surges do not necessarily result in irreparable damages to MOBOTIX IP cameras.
Only if the voltage is exceeded by a multiple of the allowed value, or if the surge is present for a longer
period of time or even permanently, damages are unavoidable.
Examples for Causes of Surges
• Direct lightning strike into the installation itself or the network cable
• Lightning strike into the power supply or the ground in the vicinity (within a radius of 100km/62mi)
• Switching of high loads, especially if network and power lines run side-by-side
Surge Protection
In order to reduce the danger of damages resulting from surges, a specialist should establish a surge
protection concept and implement such a system. Such a system consists of several surge protection zones,
where each zone contains specific and generally applicable countermeasures. These range from lightning
capture devices and double-shielded network cables to fine-level surge protection for end devices. When
selecting the countermeasures, not only technical, but also economical aspects need to be considered in
order to find the proper balance between protection and costs.
The MX-Overvoltage-Protection-Box-RJ45 and MX-Overvoltage-Protection-Box-LSA can be used in most
of the protection zones and provide a cost-ecient protection against surges. It is generally recommended
to install an MX-Overvoltage-Protection-Box if MOBOTIX cameras are installed outside of buildings. These
devices protect MOBOTIX cameras against short surges of up to 4kV.
Caution
• The cable between the MX-Overvoltage-Protection-Box and the MOBOTIX camera must not be
longer than 50cm/19.7in.
• An MX-Overvoltage-Protection-Box protects against surges of up to 4kV on a network patch or
installation cable, but not against direct lightning strikes.
MX-Overvoltage-Protection-Box-RJ45
MX-Overvoltage-Protection-Box-RJ45:
Patch Cable/Patch Cable
The patch cables with integrated sealing rings (available from MOBOTIX in dierent lengths) are
simply inserted into the RJ45 connectors and fastened using the bayonet catch (1 patch cable to
end device, 1 patch cable to PoE switch/injector). The ground wire is attached at the center (only
qualified electricians are allowed to do this!).
MOBOTIX patch cable
(network)
MOBOTIX Camera
MOBOTIX patch cable
max. 50cm
Ground wire
1,5to 2,5mm2
MX-Overvoltage-Protection-Box-LSA
MX-Overvoltage-Protection-Box-LSA:
Patch Cable/Installation Cable
Installation cable
(network)
MOBOTIX Camera
MOBOTIX patch cable
max. 50cm
This variant allows using a network installation cable to the PoE switch. The wires are inserted
into the LSA terminal in the center, while the MOBOTIX patch cable connects to the camera. The
ground wire is attached at the left (only qualified electricians are allowed to do this!).
MX-Overvoltage-Protection-Box-RJ45:
MOBOTIX patch cable to MOBOTIX patch cable
MX-Overvoltage-Protection-Box-LSA:
MOBOTIX patch cable to network installation cable
Ground wire
1,5to 2,5mm2
Weatherproof (IP65)
–30 to +60 °C/–22 to 140 °F

EN
www.mobotix.com
Innovations – Made in Germany
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its
decentralized concept has made high-resolution video systems cost-ecient.
MOBOTIX AG • D-67722 Langmeil • Phone: [phone] • Fax: [phone] • [email protected]
Quick Install MX-Overvoltage-Protection-Box
Security-Vision-Systems
 2013 • Declaration of Conformity: www.mobotix.com> Support> MX Media Library> Certificates
Copyright © MOBOTIX AG 2013 • Made in Germany • Technical information subject to change without notice.
80mm/3.2in
80mm/3.2in
75mm/3in
15mm/
0.6in
MX-Overvoltage-Protection-Box
VarioFlex Wall Mount
Drilling templates for other MOBOTIX wall mounts: www.mobotix.com> Support> Manuals
Drilling Template for VarioFlex Wall Mount
with MX-Overvoltage-Protection-Box
1. Attach the box
Attach the MX-Overvoltage-Protection-Box-LSA at the
mounting position with the cable ports pointing down-
wards and open the lid of the box (three screws).
2. Connect ground wire
Open the terminal screw (red circle in figure) using a
regular screw driver. Strip the insulation of the supplied
or existing ground wire for approx. 5mm/0.2in and
push the wire through the eight-wire plug at the left.
Insert wire into terminal and fasten terminal screw.
3. Prepare the installation cable
Cut the installation cable to size, push it through the
cable plug 5to 7mm in the center, strip the cable for
at least 35mm and separate the individual wires of the
cable into twisted pairs with 20mm shielding. Wrap
the shield mesh around the cable sheath 10mm wide
so that it can rest on the contact plate of the board.
The cable will be fastened with a cable tie later on.
4. Feed the cable into the box
In order to prevent humidity entering the box, the rub-
ber sleeve needs to be tight against the cable. Guide
the supplied cable tie through the two cable slots as
shown and pull the cable tie tight around the cable
shield to provide proper strain relief.
5. Connect the cable wires
Use an LSA PLUS wire insertion tool to insert the in-
dividual wires into the LSA terminal. Decide on using
either the EIA/TIA-568A or B wiring standard as in the
rest of the building. The color code sticker in front of
the LSA terminal shows both standards.
If no LSA PLUS tool is available, you can use a tool with
interchangeable blades (LSA/Krone blade with setting
"Low Impact").
6. Attach the patch cable, close box
Remove right-hand bayonet catch and sealing plug,
insert MOBOTIX patch cable into the cable port and
secure it using the bayonet catch as shown. Only use
MOBOTIX patch cables with integrated sealing ring!
Mount the cover back onto the box (torque 0.4Nm).
MX-Overvoltage-Protection-Box-LSA
Installing the MX-Overvoltage-Protection-Box-LSA
~20mm
~35 mm
~15 mm
~10 mm
Shield meshCable sheath Pair shield
Important Notes
• The cable from the MOBOTIX device to this product must not be longer than 50cm/19.7in.
• When using an installation cable, pay attention to the correct twisting and shielding of the cable.
• Position of holes in combination with VarioFlex wall mount: see drilling template below.
• All unused ports must be closed with the supplied rubber seals.
• Maximum torque for all box cover screws: 0.4Nm.
• The ground wire may only be connected by qualified electricians.
• This product must not be used in locations exposed to the dangers of explosion.
• It is only allowed to connect one MOBOTIX device to this product.
• Make sure that you are installing this product on a solid surface.
• Make sure that you are installing this product with the connectors point-
ing downwards.
• If the surcharge is higher than 4kV, internal parts may get destroyed in
order to prevent damage to the attached device. In this case, you will
have to exchange the MX-Overvoltage-Protection-Box at your own cost;
any warranty is excluded.
Technical Specifications
Normal Usage Surge protection for MOBOTIX cameras with PoE power supply
(PoE+ according to IEEE 802.3at up to 57V)
Protection Against Surges Tested up to 4kV on all wires of an attached cable according to test standard
EN61000-4-5
Protection class IP65 (DIN EN 60529)
Operating temperature –30 to +60 °C/–22 to 140 °F (DIN EN 50125)
Strength of the Ground Wire 1.5to 2.5mm2
1. Attach the box
Attach the MX-Overvoltage-Protection-Box-RJ45 at
the mounting position with the cable ports pointing
downwards and open the lid of the box (three screws).
2. Connect ground wire
Open the terminal screw (red circle in figure) using a
regular screw driver. Strip the insulation of the supplied
or existing ground wire for approx. 5mm/0.2in and
push the wire through the eight-wire plug in the center.
Insert wire into terminal and fasten terminal screw.
3. Attach the patch cable, close box
Remove both bayonet catches and the sealing plugs,
insert MOBOTIX patch cables into the cable ports and
secure them using the bayonet catches as shown. Only
use MOBOTIX patch cables with integrated sealing ring!
Mount the cover back onto the box (torque 0.4Nm).
MX-Overvoltage-Protection-Box-RJ45
Installing the MX-Overvoltage-Protection-Box-RJ45
80
80
15
75