modeazy Double Shoe Rack User manual

modeazy.com
Double Shoe Rack

Manual Guide Notes
Maintenance
•Please read the following instructions carefully and use the product properly.
•Keep this manual for future assemblies or hand over when you transfer the
product.
•Check the product upon receiving and make sure there are no manufacturing defects.
All products go through Quality Control before packaging and transport.
•Please use the specified tools required for assembly.
•Avoid using any adhesives or additional parts during assembly.
•Please contact us at [email protected] if further information is needed.
•Clean the product with a dry soft cloth. Avoid cleaning the product with a hard item or
chemically unsuitable product.
•Please make sure to keep your items and shoes clean before placing them.
•In case of using a mildly wet cloth, please make sure to dry the surfaces immediately
after cleaning.
•When disassembling the item, please make sure to use the same tools required for
assembly.
•In any case of rust on metal hardware, please use suitable rust-removers.
•If something is stuck on the surfaces, do not use abrasive tools to remove them, as
these could leave scratches or marks. Please use lint-free cloths or sponges instead.
Warning
•The product contains small parts and sharp objects, please be careful during
assembly and keep children away.
•Keep plastic bags away from children in case of suffocation.
•Please make sure to keep the item away from extreme conditions (such as
high humidity, high temperatures, intense sunlight, excess water, etc.)
•Do not place any sharp objects or corrosive materials on the product to avoid any
damage. In cases of placing sharp footwear like ice skates, please use blade guards.
•Please do not force large size shoes into the product in order to avoid deformation.
•The product has a tested loading capacity for regular objects and shoes, but in any
case, please do not place overweight objects, do not stand on the product and keep
children away from jumping on the product.
•The vendor does not take responsibility for any damage or injury caused by improper
assembly or use.

Approximate Dimensions: 28x26.5x108 cm / 11x10.5x42.5 inch (W x L x H),
Distance In Between Middle Shelves: 12.5 cm / 4.9 inch (H),
Distance In Between Bottom Shelves: 18.5 cm / 7.3 inch (H),
Weight Capacity Of Each Shelf: 5 kg / 11 lbs.
With seven tiers, organize your shoes and maximize your space. You can organize
different shoes on different racks, and due to it being light weight and portable, you can
easily carry and place the item anywhere that is most suitable for your usage, like
entrances, hallways, rooms, etc.
You can also place small miscellaneous items on top or in between the shelves like
CD’s, books and artworks.
Our shoe rack is made of durable MDF material and produced in accordance with
European E1 quality standards. It has non-harmful paint and used materials suitable for
environmental and child health.
Compliance Statement: California 93120 Phase 2 and TSCA Title VI Compliant for
Formaldehyde
“Product Description”
Before assembly, check all parts and accessories.
If any are missing or damaged, please do not
return the product and contact us at
[email protected].

1
•The product contains small parts and sharp objects, please be careful during
assembly and keep children away.
•Keep plastic bags away from children in case of suffocation.
•Please make sure to keep the item away from extreme conditions (such as
high humidity, high temperatures, intense sunlight, excess water, etc.)
•Do not place any sharp objects or corrosive materials on the product to avoid any
damage. In cases of placing sharp footwear like ice skates, please use blade guards.
•Please do not force large size shoes into the product in order to avoid deformation.
•The product has a tested loading capacity for regular objects and shoes, but in any
case, please do not place overweight objects, do not stand on the product and keep
children away from jumping on the product.
•The vendor does not take responsibility for any damage or injury caused by improper
assembly or use.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
PARTS LIST
A
B
C
D
E
Vertical Supports (Qty 3)
Top Piece (Qty 1)
Bottom Piece (Qty 1)
Shelves - With Dowel Opening (Qty 5)
Shelf - With Screw Opening (Qty 1)
FAllen Screws (Qty 9)
HDowel Pins (Qty 15)
GAllen Key (Qty 1)
İScrew Cover Stickers (Qty 6)
HF
A
D and E
INNER VIEW
1.1
1.2
Lay parts out on a protective surface to prevent damage.
Tip: Spread out the cardboard
packaging to use as a protective surface.
Make sure all parts are present before proceeding.
OUTER VIEW
G
IMPORTANT NOTE: The Allen Screws are 5mm in diameter, and the Dowel Pins are 8mm in
diameter. Their openings on the sides of the shelves have been done accordingly to these
measurements. Please do not force the Dowel Pins into the middle shelf that has the Allen
Screws’ opening.
BC
İ

2
2.1
•Before assembly, make sure to check all the parts and accessories. If any
parts are missing or damaged, please do not return the product. Instead,
please contact us within a week of receiving the product and share the item
name(s) that is missing or damaged and we will send you a replacement.
A
2.3
Place one of the Vertical Supports (A) on the floor. Make sure the inner view is facing
upwards. The ‘’y’’ measurement is greater than ‘’x’’, the ‘’y’’ side is the bottom section of the
product. Note: Place this part on a soft surface such as cardboard or a carpet to avoid any
damages from underneath.
A
2.2 Place the Dowel Pins (H) in the openings. Do this process for the other two Vertical Supports
(A) and place them carefully aside for later use. Do not place a pin in the Allen Screw (F)
opening.
H
F opening
Separate the Shelves with dowel openings (D) and the Shelf with screw openings (E) in order
to avoid any mix-up.
D E
Qty: 5 Qty: 1
x y

3
3.3
3.1 Start inserting the Shelves (D) onto the Dowel Pins (H) that you had placed into the Vertical
Support (A). Make sure the side with no openings of the Shelves (D) faces upwards. Leave
the Allen Screw opening (F) empty.
F opening
A
D H
Insert the Allen Screw (F) into the opening of the Shelf (E), rotate it using an Allen Key
(G) until it is firm. Do not rotate more than necessary.
F
A
E
TURN
CLOCKWISE F
3.2 Turn the Vertical Support (A) with the attached Shelves (D) to its side in order to easily attach
the Shelf with the screw opening (E).
DDDDD E
A
F opening

4
4.1 Lay the partially assembled product on it’s back with the Vertical Support (A) touching the
floor.
A
4.2
Bring the other two Vertical Supports (A) and place them next to the partially assembled
product on the floor.
A
A
A

5
5.1 Attach the Vertical Supports (A) to the partially assembled product by inserting the Dowel
Pins (H) existing on the Vertical Supports (A) into the openings on the Shelves (D).
5.2 After attaching the Vertical Supports (A) to the sides, insert the Allen Screws (F) with the
Allen Key (G) on both sides.
F opening
F opening
F
A
E
TURN
CLOCKWISE F
D
A
H

66
6.1 Bring the Top Piece (B) and Bottom Piece (C) and place them to the sides of the partially
assembled product.
B
F opening F opening
6.2 Attach the Top Piece (B) and Bottom Piece (C) corresponding to the openings, and use the
Allen Key (G) to fix the Allen Screws (F) into the holes.
F opening
TURN
CLOCKWISE F
C
BC

7.1 Bring your assembled product to an upright position, keeping the biggest shelf gap located at
the bottom.
7

8.1 Take out the Screw Cover Stickers (İ) and stick them onto the screw openings seen on the
Vertical Supports (A) and the Top Piece (B).
B
İ
TOP VIEW
A
İ
8.2 After sticking the Screw Cover Stickers (İ) onto the corresponding screw openings on the
Vertical Supports (A) and the Top Piece (B), you can start using your product.
TOP VIEW
B
İ
Aİ
OUTER VIEW
OUTER VIEW
8
İ

Thank you for your purchase.
Please contact us if you have any questions or difficulty with
assembly.
Email: [email protected]
Please make sure to share your full name and order details
so that we can assist you better.
modeazy.com
/modeazy /modeazycom