Modern Forms F-RC-WT User manual

OPERATION INSTRUCTIONS
SMART
F-RC-WT
COMPATIBLE WITH
Package Contents
Pairing
To pair your remote control:
1. Power cycle your fan by removing power to the circuit for
10 seconds and then re-enable power.
2. Press and hold and buttons on remote control
for 10-15 seconds.
3. The LED will blink green then remain solid green.
4. The green LED along with audible beeps will indicate
that pairing is successful.
5. Test remote control using the steps in section 2.
1button: Switch between Summer and Winter Mode.
SUMMER MODE (Counter-Clockwise):
A downward airow creates a cooling
eect (FIG. 3). This allows you to set
your air conditioner on a warmer
setting without aecting your comfort.
WINTER MODE (Clockwise):
An upward airow moves
warm air o the ceiling area and
re-distributes the warm air that hovers
around the ceiling to the living space.
This should allow for savings on
heating costs (FIG. 4).
NOTE: To operate the reverse button on your fan,
press the button while the fan is running
Remote Control Operation
Remote Control Button Functions
button: Turns the light ON or OFF.
Press or hold to increase the light level.
Press or hold to decrease the light level.
button: Turns the fan ON or OFF.
Press or hold the button to increase fan speed.
Press or hold the button to decrease fan speed.
NOTE: Your fan features 6 speeds. An audible tone will indicate
when the speed is increased or decreased. When the fan has
reached the minimum/maximum speed level the audible
indication will stop.
2
BatteriesRemote Wall Cradle
Screws
CR2032
CR2032
Unpairing
NOTE: Unpairing must be completed within 3 minutes
of turning the power on to the fan receiver.
1. When you re-engage power to the fans you
want to unpair, press and hold the and
buttons for 4 seconds.
2. The LED will alternate red/green, blink green, and the
receiver will beep to indicate that unpairing is successful.
3
Press and Hold
Press and Hold
NOTE: A maximum of 2 fans can be operated using the
remote control.
FIG.1
FIG.2
FIG.3
FIG.4
FIG.5

Fan Wi-Fi Reset
NOTE: This function only resets the Wi-Fi credentials.
1. Press and hold the and buttons for 6 sec.
2. The LED will light red blink green and return to solid
red, and the receiver will beep to indicate that Wi-Fi
reset is successful.
3. After the Wi-Fi resets, the fan will broadcast its service
set indicator (SSID).
NOTE: If you are updating your router the fan will still
appear in the Modern Forms app but will need to be
re-paired. You can change the name of your fan on the
Modern Forms app upon re-pairing.
45
Factory Reset
NOTE: This will remove remote control and app connections.
Remote Control Factory Reset:
1. Press and hold the , and buttons
for 10 seconds.
2. The LED will blink red and return to solid red,
and the receiver will beep to indicate that the
factory reset is successful.
Receiver Button Factory Reset
1. Press the reset button on the receiver until the
receiver control beeps.
NOTE: This will remove remote control and Modern Forms
app connections.
6
Modern Forms App
FIG.6
FIG.7
FIG.8
Press and Hold
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
CAUTION: The user is cautioned that changes or modications
not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Supplier’s Declaration of Conformity
Brand name / model number: Modern Forms / F-RC-WT
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Suppliers Name : WAC LIGHTING CO.
Suppliers Address (USA) : 44 Harbor Park Drive,
Port Washington, NY 11050
Suppliers phone number: 1-866-810-6615
Rules and Regulations