Modern Forms F-RCUV-WT User manual

OPERATION INSTRUCTIONS
F-RCUV-WT
Package Contents
Pairing
To pair your remote control:
1. Power cycle your fan by removing power from the circuit
breaker for 10 seconds and then re-enable power.
2. Press and hold and buttons on remote control
for 4-5 seconds.
3. The LED will blink green.
4. The green LED along with audible beeps will indicate that
pairing is successful.
5. Test remote control using the steps in section 2.
1button: Switch between Summer and Winter Mode.
SUMMER MODE (Counter-Clockwise):
A downward airow creates a cooling
eect (FIG. 3). This allows you to set
your air conditioner on a warmer
setting without aecting your comfort.
WINTER MODE (Clockwise):
An upward airow moves
warm air o the ceiling area and
re-distributes the warm air that hovers
around the ceiling to the living space.
This should allow for savings on
heating costs (FIG. 4).
NOTE: On your fan, press the button while the fan is running
Remote Control Operation
Remote Control Button Functions
button: Turns the light ON or OFF.
button: Turns the fan ON or OFF.
Press or hold the button to increase fan speed.
Press or hold the button to decrease fan speed.
2
BatteriesRemote Wall Cradle
Screws
CR2032
CR2032
Press and Hold
NOTE: A maximum of 10 remote controls or wall
controls can be used with a fan.
NOTE: Pairing must be completed within three (3) minutes of
turning the power ON to the fan receiever.
FIG.1
FIG.2
FIG.3
FIG.4
4
3
Breeze Mode
1. Breeze Mode mimics the natural ebb and ow
of winds in nature by varying the fan speed.
NOTE: Breeze Mode always rotates your fan
in the Summer (CCW) direction
2. To start Breeze Mode, press and
for 4 seconds. The LED will blink green
and the fan will beep.
3. To exit Breeze Mode and return to standard
fan mode, press and for 4 seconds.
The led will blink green and the fan will beep.
Your fan will return to the direction and speed
it was set to prior to entering Breeze Mode.
NOTE: Your fan features 6 speeds. An audible tone will
indicate when the speed is increased or decreased. When
the fan has reached the minimum/maximum speed level
the fan will beep twice.
UV Auto-O feature:
This feature will automatically turn o the UV light after a xed
period of time. Feature is o by default. To enable/disable, Press
and hold Light Toggle and Fan up for 4 seconds fan will beep
indicating change. Default time: 45 minutes. Duration can be
changed using the App.
Germicidal Smart Fan

Fan Wi-Fi Reset
NOTE: This function only resets the Wi-Fi settings.
1. Press and hold the and buttons for 10 sec.
2. The LED will blink green and the receiver will beep to
indicate that Wi-Fi reset is successful.
3. After the Wi-Fi resets, the fan will broadcast its factory
set network name beginning with “ModernFormsFan.”
NOTE: Changes to your Wi-Fi network settings
(SSID or Security Passphrase) will prevent your fan from
connecting to the cloud. You can re-establish connectivity
by performing a Wi-Fi Reset and using the Modern Forms
app to recongure the fan to connect to the network with
the new settings.
7
8
Factory Reset
Using remote control
Remote Control Factory Reset:
1. Press and hold the , and buttons
for 10 seconds.
2. The LED will blink green and the receiver will beep
to indicate that the factory reset is successful.
CAUTION: The user is cautioned that changes or modications
not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
WARNING: This product emits ultraviolet (UV) radiation.
Exposure to UV radiation can cause serious personal injuries,
including damage to eyes and skin. Do not operate the product
while anyone could be directly exposed to the UV light. For more
safety instructions, please refer to the instruction manual.
FCC Supplier’s Declaration of Conformity
Brand name: Modern Forms
Model number: F-RCUV-WT
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
WAC LIGHTING
44 Harbor Park Drive, Port Washington, NY 11050
Tel: [phone]
Rules and Regulations
Unpairing
NOTE: Unpairing must be completed
within 3 minutes of turning the power
on to the fan receiver.
1. When you re-engage power to the
fans you want to unpair, press and
hold the and buttons
for 4 seconds.
2. The LED will blink green, and the
receiver willbeep to indicate that
unpairing is successful.
5
FIG.5
Press and Hold
“The bluetooth® word mark and logos are registered trademarks owned
by Bluetooth SIG, Inc. and any use of such marks by Wangs Alliance
Corporation is under license. Other trademarks and trade names are those
of their respective owners.”
NOTE: This will remove remote control(s), wall control(s)
and Modern Forms app connections
UV end-of-life notication and
reset procedure:
The UV module will lose ecacy beyond 9000 hours of use.
The fan automatically tracks module usage. When there is
approx 10% life remaining the user will be notied by the
light module blinking in an on/o patern for the rst 10
seconds after turning it on.
This is an indication the user should replace the module.
To reset the fan’s internal counter, press and hold the
and for 4 seconds. the fan receiver will beep
short-long-short to indicate the reset was successful.
6
WARNING: Chemical Burn Hazard. Keep batteries
away from children. This product contains a lithium
button/coin cell battery. If a new or used lithum button/
coin cell batter is swallowed or enters the body, it can
cause severe internal burns and can lead to death in as
little as 2 hours. Always completely secure the battery
compartment. If the battery compartament does not
close securely, stop using the product, remove the
batteries, and keep it away from children. If you think
batteries might have been swallowed or placed inside any
part of the body, seek immediate medical attention.