Mojave LUNCHBOX User manual

M
o
j
a
v
e

M
o
j
a
v
e
M
o
j
a
v
e
“LUNCHBOX”
Operating Instructions

M
o
j
a
v
e
1.0 Quick Setup
The first step to getting started with your new “LUNCHBOX” repeater, is to
plug in the USB charging cable on the side of the radio. It can be identified by
the yellow tip and should be plugged into the port beneath the audio jack.
In order to start the repeater, press the black button on the right side of the
shelf. Release the button when the lights flash. A flashing red light indicates
that the repeater is on and ready.
Next, use the volume knob to turn the radio on. It is best to use the radio at
approximately 50% volume, for clear transmissions over the net.
The radio has the MURS, FRS, and GMRS frequencies pre-programmed.
Tune your personal radio to the same frequency as the repeater. Test a
transmission. If you hear your transmission back, this indicates that the
repeater is fully functional.
Once the USB charging cable is
plugged in, you are able to use the
two USB bulkheads on the side of
the radio to charge the repeater
controller and the radio.
The USB port on the left side is for
the controller and the right side is
for the radio.
Controller Radio

M
o
j
a
v
e
2.0 Repeater Controller Operation
2.1 DTMF Tones
The “LUNCHBOX” utilizes a simplex repeater controller to relay transmissions
over a set frequency. All operation of the repeater controller can be achieved
through utilizing the black button inside the case or DTMF tones from your
radio, with feedback from tones and four LED indicator lights inside the case.
To power the controller ON, press the black button inside the case one time.
For power OFF, hold down the black button until three red lights indicate that
the power has been turned off.
The first step in utilizing DTMF tones for your “LUNCHBOX” repeater is to
setup a new password. Once the radio and controller are powered on and
you have verified their operation using the quick setup guide on page 1, you
can set the password. On your personal radio, key out using the PTT button,
and use the following keypad button combo on your radio:
After you complete this step, you must enter your new password again with
the following combination to confirm the new password.
#
#
#
#
3
4
8
1
8
2
8
3
8
4
1234
Mode
Mode
Default Password
New Password
New Password

M
o
j
a
v
e
2.0 Repeater Controller Operation
2.1 DTMF Tones (Continued)
Once you have set your new password, you can utilize it in conjunction with
some of the following supported DTMF tones in this table:
# # 1 + 8 8 8 8
# # 2 + 8 8 8 8
# # 5 1 + X
# # 5 2 + X
# # 5 3 + X
# # 5 4 + X
# # 5 9 + X
# # 6 1 + X
# # 7 1 + X
# # 8 1 + X
# # 8 3 + X
# # 8 5 + X
# # 8 2 + X
# # 8 4 + X
# # 8 6 + X
Enable recording function (wake up repeater)
Disable recording function (sleep repeater)
Delay time after releasing PTT (X = 1-9) in units of 0.1s
Delay time after message playback (X = 1-9) in units of 0.1s
Message Record Level (X = 1-9) Default Value is 5
Message Playback Level (X = 1-9) Default Value is 5
Enable/Disable Roger Beep (X=1 to Enable, X=0 to Disable)
Replay last transmission sent over the repeater
Record Message #1. Max message length is 60s
Record Message #2. Max message length is 60s
Record Message #3. Max message length is 60s
Playback Message #1
Playback Message #2
Playback Message #3
Message Repeat
X = 0 Disable Repeat Messages
X = 1 Repeat message once every 15 minutes
X = 2 Repeat message once every 30 minutes
X = 3 Repeat message once every 45 minutes
X = 4 Repeat message once every 60 minutes
Tone Action

M
o
j
a
v
e
2.0 Repeater Controller Operation
2.2 Factory Reset
2.3 Indicator LEDs
In order to reset your repeater controller to factory settings, press and hold
the black button inside the case for approximately three seconds until you see
three red LED lights come on sequentially.
Several LEDs indicate the status and operation of the repeater controller.
They show the following status/actions:
Blue - Battery
Fully Charged
Red - Battery
Charging
Battery / Audio
Level (Red and
Blue LED)
Red Blinking -
Repeater ON
and recording
Solid Red -
Repeater RX
Solid Blue -
Repeater TX
Blue Blinking -
Repeater
Sleeping