MojoDesk ET223 User manual

F
4x4
275 lbs
22.8-48.4 inch
43.3-74.8 inch
3
1
2
3
4
6
5
5
F
A
A
C
D
4
B
E
4
F
16
61
3 1 4 1
71
1 2 2 2
52
4
D
F
2
12
8
C
F
7
A
5
1
2
4
MojoDesk 2020 Assembly Guide
Column Stage
Technical data
Max. Weight Capacity
Height Range
Width Range
Accessory list
No. Image Spec Qty
Attention: The drawings below are for guidance only and they may differ
slightly from the product and fittings received. Please contact our customer
service department should you have any queries.
Allen Key
4x4mm 1
M6
St4.2
M6
M6
M6
Component list
No. Part Qty No. Part Qty
No. Part Qty No. Part Qty
No. Part Qty No. Part Qty
No. Part Qty
Feet Lifting Column
Side Bracket
Control Panel
Power Plug
STEP 1 Install the Side Brackets
Attach the side brackets(5) to the ends of the supporting beam (4) using
screws(A) as show with the Allen Key(F).
Supporting Beam
(Control Box included)
Cable Management Tray
Install the Lifting Columns
Install the Feet
STEP 3
STEP 2
Insert the lifting columns (2) into the ends of the supporting beam(4).
Fix the lifting columns using screws(D) with the Allen Key(F).
Place the feet(1) on the bottom of the lifting column(2).
Fix the feet using screws(C) with Allen Key(F).
Ax4
Dx8
F
4x4
Cx8
F
4x4

F
4x
2
1
E
6
3
4
B
E3
4
D
12
3
A C
H S M 1 M 2
7
D C
B
STEP 4
STEP 5
STEP 6
Install the Tabletop
Install the Control Panel
Port for
control panel
Power
Port for cable
connected to the
lifting column
Install the Cable
Management Tray
Method 1 for 48" and 60" MojoDesks
Tighten
First, partially insert the screws (B) into the supporting beam (4) with
Allen Key (F), which means do not tighten them. Next, insert one
side of the cable management tray (3) under the screw heads (B),
then the other side. Finally, tighten the screws (B) with Allen Key (F).
Method 2 for 72" wide MojoDesk
When the supporting beam stretches over 67.7inch,
the cable management tray needs to be mounted on
the middle of the supporting beam.
Do not stretch the support
beam beyond this hole
Troubleshooting
The following tips help identify and eliminate common faults and errors.
If the fault is not listed below, please contact MojoDesk. Our customer
support team is here to assist.
Problem Solution
No response when pressing and
holding the DOWN button 1.Check if all cables are well connected
1.Check if all the cables are well connected
2.Contact MojoDesk support
2.Contact MojoDesk support
No response while pressing the
UP button and the DOWN
button at the same time
Lifting speed is slow 1.Check if overloaded, max load: 250 lbs
1.Check if overloaded, max load: 250 lbs
1.Check if overloaded, max load: 250 lbs
2.Contact MojoDesk support
2.Contact MojoDesk support
2.Contact MojoDesk support
Desk does not move as instructed 1. Contact MojoDesk support
1.Reset desk
2.Contact MojoDesk support
Desk goes down but not up
Desk moves down without
button press
Frequently needs to be reset
Overuse
（Duty cycle:Max 2min on/18min OFF）
1.Resume use after 18min rest
2.Contact MojoDesk support
1. Press "M"and "3" together for 3 seconds or more,
after hearing continuous beeping twice, it will restore
factory settings
Limited up & down range
2.Contact MojoDesk support
Attention
1. Power supply: AC100V-240V,50/60Hz
2. Service Environment: 0-40℃
3. Unplug the power plug before cleaning, wipe the dust on surface with damp cloth
when cleaning, be careful not to let water get into the internal parts.
4. The control box contains electronic components, metals, plastics, wires etc., so
dispose of it in accordance with your country's environmental legislation, not in the
general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Do not let children play on the MojoDesk
8. Do not use corrosive or abrasive materials to clean your MojoDesk. Use cleaners
that will not pollute the environment.
9. Cleaning and user maintenance shall not be made by children without supervision.
10. If the power cord is damaged, contact MojoDesk support for a replacement.
11. Please make sure there are no hazard sources in your operating environment.
e.g., do not litter the tools around. Properly dispose of packaging materials to avoid
any possible choking hazards to children.
12. Keep the original packaging in case of return to MojoDesk.

Waste disposal This marking indicates that this product should
not be disposed with other household wastes.
To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly. To return your used
device, please use the return and collection
systems or contact the retailer where the
product was purchased. They can take this
product for environmentally safe recycling.
Ex12
Bx4
F
4x4
Bx4
F
4x4
Dx4
Loosen all 4 support beam
set screws
Adjust base width to
match worksurface holes
Tighten
all 4 set screws
3
4
Use screw E to attach
base to worksurface - 12x
First, partially insert the screws (B and D) into the inner supporting
beam (4) with Allen Key (F), which means do not tighten them. Next,
insert one side of the cable management tray (3) under the screw
heads (D), then the other side. Finally, tighten the screws (B and D)
with Allen Key (F).
BD
Need Help?
Visit MojoDesk.com/help
Need more help? call 800-297-6656
Help online? @MojoDesk
Slide one side under
the screw heads
Squeeze tray and
slip other side under
screw heads