Molpir KL30944 User manual

V
Vi id de eo o P Pa ar rk ki in ng g S Se en ns so or r
Dear User, Thank you for choosing and using our Parking sensor. We are going to
provide the best products and the best services to you.
To insure the best performance and avoid any false alarm or function failure, please
kindly read this manual carefully and install accordingly.
We reserve all rights for our parking sensor, including the designs and the software.
Any unauthori ed copy or translation is prohibited. And the products’ specification and
information related in the Manual provide the references only, and the content of the
Manual will be renewed according to the process of the products without advance
information, and the final explaination rights of the Manual is reserved by us.
Please note that this system is designed to be a driver’s aid and should not replace
the need to drive carefully, we accept no liability for damage or loss resulting from
importer installation or use of this product, infringement of the vehicle manufacturer’s
warranty or injury or loss resulting from any accidents however caused. If in doubt
please consult aqualified auto electrician.
Ord.code
:
KL30944
Date:
15
/0
4
/2014 Page 1/7
NM_
KL30944
_
00
0
_
1504
2014_EN

Packaging list
Display x1
Sensors x4
Cables x5
Drill bit x1
Control unit x1
Camera x1
Manual x1
Function
4.3“ TFT monitor can display the back image
2 ways video input, one is connect to the back camera, the other is connect to the
DVD/VCD
The 4 sensors can detect obstacles when reversing, and show the obstacle
distance colorfully in monitor, step-up bu er alarm.
Specifications
Rated voltage: 12V DC
Operating voltage: 9V ~ 16V DC
Rated current: 20mA ~ 300mA
Display distance: 0.3 ~ 1.8m
Ultrasonic frequency: 40kH
Monitor resolution: 320 x 240 pxl
Camera resolution: 659 x 492 pxl
Alarm MO E
Model Awareness Distance Sound Digital display Indicator
Safe mode 120 ~ 180cm Bi ...Bi... 1.2 ~ 1.8m Green
Safe mode 100 ~ 120cm Bi..Bi.. 1.0 ~ 1.1m Yellow
Alarm mode 60 ~ 100cm Bi.Bi. 0.6 ~ 0.9m Yellow
Alarm mode 40 ~ 60cm BiBi 0.4 ~ 0.5m Red
Display bu er
alarm
Dange mode 0 ~ 40cm Biiii 0.0 ~ 0.3m Red
Installation Instruction
Note: Before installing system let the components of the exhaust system cool down. This
will make the installation safer and preclude head damage to the backup sensor wiring or
components.
The following illustration shows the general location of the components of the
backup system.
Date: 15/04/2014 Page 2/7
NM_
KL30944
_
00
0
_
1504
2014_EN

Option A
Option B
Display
Control Box
Sensors
Camera
Back
-
up Light
Drill
Pliers
File
Tape Measure
Drill Bit
Masking Tape
Small flat
-
tip Screwdriver
#
2 Phillips Screwdriver
Multimeter
Black Electrical Tape
Wire
-
Snake
Pencil/Marker
Tools
Monitor
Red to back-up light +12V
Black to GND
Parking Sensor
Camera
Red to ACC +12V
Black to GND
Red to back
-
up Light +12V
Black to GND
Sensor
Control
Box
Date: 15/04/2014 Page 3/7
NM_
KL30944
_
00
0
_
1504
2014_EN

Masking Tape
50~80cm
idealy:55cm
Mark
30~40cm
Nothing
Blocking
Make sure that there is
nothing blocking the
area
behind the bumper,
where the sensors go.
Drilling position must be
perpendicular to the
surface of the bumper.
As you push, wiggle the
sensor and make sure it
goes all the way in and
flush against the bumper,
leaving no gap.
Sensor Installation
First locate where you are goingto intall the sensors and place a piece of masking tape.
Measure and mark the position of the holes.
Install the sensors vertically; the „UP“ sign must be on upside.
Limitation
The sensors may not work if an object does not reflect the ultrasonic waves or it has
an unusual shape, pole cardboard carton, tire of bicycle, small or slender tree,
rectangular lumberor curbs tone. The sensor may not detect another vehicle bumper if it
is too high.
Also note: This system has different detection distance to the different object.
To the wall, the max. detection distance is 1.8m
To the human body, the max. distance is 1.0m
To the column is Ø40cm, the max. detection distance is 1.2m
Date: 15/04/2014 Page 4/7
NM_
KL30944
_
00
0
_
1504
2014_EN

If the vehicle is equip
ped with
high-power radio antenna.
If another vehicle bumper is too
high.
When backing up downhill
.
If there is a very small object
.
If there is a wire fence
.
Backing up in heavy rain or snow
.
If is smooth slope
.
If is smooth round object
.
Object a
bsorbing wave, e.g.
Cotton.
In some special cases, the display may not be the same as the real condition due to the
sensor position, obstacle shape, reflection condition and so on. Some examples are given
below
Date: 15/04/2014 Page 5/7
NM_
KL30944
_
00
0
_
1504
2014_EN

Prepare for installing
Installing
Installed
Camera
Remove the necessary back
panels to mount the control
box in a safe place, away
from rain, heat or humidity
Pls adjust the available
angle for the camera once
finish installing
Rearviev mirror Installation
Please put this product is properly installed in your car on the original rearview mirror.
Control Box Installation
After Installation Test
Use the following to test and verify the operation of the backup system:
Warning:
Do not stand behind a moving vehicle death or injury could occur. Prior to testing, set the
parking brake On, ignition key On (do not start), step foot on brake and shiftthe vehicle
into reverse. Ensure that the engine is not running while proceeding with the following
tests.
Test the system operation with a piece of wood (60x30x1cm) or other object (not too
small) after the installation. Start with the wood more than 1m away from the vehicle.
Then move the wood closer the vehicle and ensure that the bu er, LED and distance
indicators display correctly.
Trouble shooting
No bu er or display at power up.
1. Is power wire connected to control unit correctly ?
2. Verify (+) 12V at control unit when vehicle is in reverse.
3. Verify the ground connection.
4. Have you connected to the correct reversing indicator wire ?
Date: 15/04/2014 Page 6/7
NM_
KL30944
_
00
0
_
1504
2014_EN

Note ! Specifications subject to change without notice.
5. Do you have a minimum of (+) 12V and ground at the display?
False warning tone or false display.
1. Is the sensor mounted too low or pointing to the ground?
Sensor do not detect any objects.
1. Is the vehicles exhaust smoking? Correct or allow it to clear before procedding with
testing.
2. Are sensors properly plugged into the correct sockets?
No reverse image.
1. Is the connection of camera power cable and AV cable are right or not?
2. Is AV cable connected to AV2?
Date: 15/04/2014 Page 7/7
NM_
KL30944
_
00
0
_
1504
2014_EN