Molpir MTB200 User manual

NU
_
M
TB200
_
001_05112013_EN
Date: 05.11.2013 Page 1 / 14
G
GS SM M/ /G GP PR RS S/ /G GP PS S T Tr ra ac ck ke er r
1
1. . I In nt tr ro od du uc ct ti io on n
The MTB200 is a powerf l GPS locator which designed for vehicle, pets and assets
tracking. With s perior receiving sensitivity, fast TTFF (Time to First Fix) and GSM
freq encies 850/900/1800/1900. Its location can be real time or sched le tracked by
beckend server or other specified terminals. Based on the embedded @Track
protocol, MTB200 can comm nicate with a backend server thro gh the GPRS/GSM
network and transfer reports of Emergency, Geo-fence, device stat s and sched led
GPS position etc..... Service provider is easy to set p their tracking platform based
on the f nctional @Track protocol.
Ord.code.: MTB200

NU
_
MTB200
_
001_05112013_EN
Date
:
05
.
11
.20
13
Page
2
/
14
2
2. . P Pr ro od du uc ct t O Ov ve er rv vi ie ew w
2
2. .1 1. . A Ap pp pe ea ar ra an nc ce e
2
2. .2 2. . B Bu ut tt to on ns s/ /M Mi in ni i S SB B I In nt te er rf fa ac ce e D De es sc cr ri ip pt ti io on n
B tton/Mini USB Interface Description
Power Key T rn on MTB200
T rn off MTB200 when witho t charging. (If
power key is enabled)
F nction Key Geo-Fence mode
Long press the key to enable/disable Geo-
Fence ID0
Geo-Fence in c rrent position mode Long press
the key to enable/disable Geo-Fence ID0. If
enable Geo-Fence ID0, sing the c rrent
position as the centre of Geo-Fence 0
SOS mode (defa lt)
Long press the key to active SOS alarm
Mini USB
interface Connect a 5V DC adapter that can power MTB200 and charge the internal battery
Connect a 3.7V Li-Ion or Li-Polymer battery can
power MTB200
Backend server developer or administrator can
se the CA80189 to config re MTB200
SIM Card Slot
F nction Key
Mini-USB
&
Antenna
Interface
Power Key
GPS LED
PWR LED
GSM LED

NU
_
MTB200
_
001_05112013_EN
Date
:
05
.
11
.20
13
Page
3
/
14
2
2. .3 3. . L LE ED Ds s D De es sc cr ri ip pt ti io on n
There are three LED in MTB200, the description as following.
LED Event State
Searching network Fast flash
Network has been registered Slow flash
Power off Dark
SIM-PIN Locked Solid
Receives a valid protocol command T rn on for 3 seconds
GSM LED
<LED on> is 2 Dark
GPS has fixed Solid
GPS is in fixing Fast flash
GPS is on and GPS data wrong Slow flash
GPS is off Dark
If <LED on> is 0, 150 seconds later
after powers on Dark
GPS LED
<LED on> is 2 Dark
Power on and normal Dark
Charger inserted and charging
completed Solid
Charger inserted and charging Fast flash
Power key was pressed and prepare
to power off Fast flash
Abnormal Fast flash
Power low alert Slow flash
Power off or t rn off the power light
by command Dark
Power LED
<LED on> is 2 Dark

NU
_
MTB200
_
001_05112013_EN
Date
:
05
.
11
.20
13
Page
4
/
14
2
2. .4 4. . E Ex xt te er rn na al l P Po ow we er r I In nt te er rf fa ac ce e
2
2. .4 4. .1 1. . E Ex xt te er rn na al l D DC C C Ch ha ar rg ge er r I In nt te er rf fa ac ce e
The PIN2 on Mini-USB connector are sed for charging and named as VCHG
PIN, it can be connected to a 5V DC power s pply to power MTB200 and
charge the internal battery.
2
2. .4 4. .2 2 E Ex xt te er rn na al l B Ba at tt te er ry y I In nt te er rf fa ac ce e
The PIN8 on Mini-USB connector is for external battery and named as
EXTBAT PIN, it can be connected to 3.7V Li-Ion or Li-Polymer battery to
power MTB200.
2
2. .5 5. . I Ig gn ni it ti io on n D De et te ec ct ti io on n
The PIN7 on Mini-USB connector is for ignition detection when
MTB200 is sed in vehicle tracking application, it is named as
IGN_IND PIN.
GND
VCHG (4.75~5.25V)
MTB200
10PIN
Mini-USB
GND
EXTBAT (3.6~4.2V)
MTB200
10PIN
Mini-USB

NU
_
MT
B200
_
001_05112013_EN
Date: 05.11.2013 Page 5 / 14
Another easy way is to connect PIN7 to a power o tp t in the f se box of the
vehicle which is only enabled after the vehicle is ignition on. For example:
the power o tp t for radio FM.
2
2. .6 6. . E Ex xt te er rn na al l I In np pu ut t I In nt te er rf fa ac ce e
The older hardware version of the MTB200 whose IMEI code is between
35946403600001X (ignore the last one parity bit X) and 35946403607338X
do not s pport the inp t f nction, before sing the inp t f nction, yo sho ld
check if the MTB200 is a newer hardware version.
The PIN5 on Mini-USB connector is a negative trigger inp t in newer
hardware version, it is named as NSW PIN.
For negative trigger inp t the electrical conditions are:
Logical State Electrical State
Active 0V ~ 0.8V
Inactive 1.7V ~ 32V or Open
GND
IGN_IND (8~32V)
Vehicle ignition
switch
Start(4th position)
Accesories(2th position)
Off(1th position)
R n(3th position)
Vehicle
’s
battery line
MTB200
10PIN
Mini-USB

NU
_
MTB200
_
001_05112013_EN
Date
:
05
.
11
.20
13
Page
6
/
14
An inp t example is shown as following fig res:
2
2. .7 7. . E Ex xt te er rn na al l O Ou ut tp pu ut t I In nt te er rf fa ac ce e
The older version of the MTB200 whose IMEI code is between
35946403600001X (ignore the last one parity bit X) and 35946403607338X
do not s pport the o tp t f nction, before sing the o tp t f nction, yo
sho ld check if the MTB200 is a newer hardware version.
The PIN9 on Mini-USB connector is a negative trigger o tp t in newer
hardware version, it is named as OUT PIN.
The o tp t is Open-Drain type with no internal p ll- p resistor which also
can be sed to control a relay. It means that the ser has to connect a p ll-
p resistor or a relay coil between the o tp t PIN and any positive voltage
(32V max.) to generate a correct o tp t. It can drive a maxim contin o s
c rrent of 0.15A.
For negative trigger o tp t the electrical conditions are:
Logical State Electrical State
Enable <0.4V, max. c rrent is 0.15A
Disable Open or the p ll- p voltage (max. 32V)
Panic B tton
GND
MTB200
10PIN
Mini-USB
NSW
Example of NSW PIN connect to a panic b tton

NU
_
MTB200
_
001_05112013_EN
Date
:
05
.
11
.20
13
Page
7
/
14
The o tp t examples are show as following fig res:
If the digital o tp t is sed to drive a relay, a catch diode is showed across the
relay coil, this is necessary to prevent damage to the digital o tp t
when the relay is t rned off. Many modern relays come with this
POWER
REZISTOR
LED
GND
MTB200
10PIN
Mini-USB
OUT
Example of OUT PIN drive a LED
86
8
5
8
7
30
87A
MTB200
10PIN
Mini-USB
OUT
DIODE 1N4004
RELAY
Vehicle’s
battery line
Example of OUT PIN drive
a relay

NU
_
MTB200
_
001_05112013_EN
Date: 05.11.2013 Page 8 / 14
diode pre-installed internal to the relay itself. If the relay has this diode,
ins re the proper relay polarity connected is sed. If this diode is not
internal, it sho ld be externally. A common diode s ch as a 1N4004 will work
in most circ mstances.
2
2. .8 8. . E Ex xt te er rn na al l G GP PS S a an nt te en nn na a s sp pe ec ci if fi ic ca at ti io on n
There is a MMCX RF connector on MTB200 and it is for external GPS antenna.
The specification of the external GPS antenna is listed in following table.
GPS antenna Frequency: 1575.42MHz
Bandwidth >5MHz
Beamwidth >120°
S pply voltage 3.3V
Polarization RHCP or Linear
Passive 0dBi min.
Gain Active 15dB
Impedance 50Ω
VSWR <2
Noise fig re <3
Connector MMCX
3
3. .0 0. . G Ge et tt ti in ng g S St ta ar rt te ed d
3
3. .1 1. . P Pa ar rt t L Li is st t
Name Remark Pict re
MTB200
The GSM/GPRS/GPS
locator

NU
_
MTB200
_
001_05112013_EN
Date
:
05
.
11
.20
13
Page
9
/
14
AC-DC Power Adapter
(Standart accesory)
It is sed to charge
the internal battery of
MTB200
MTB200 Sheath
(Optional accesory)
It is sed to attach
the MTB200 to belt
Car Cigarette Charger
(Optional accesory)
It is sed to power the
MTB200 with the
cigarette power o tp t
on the vehicle
Car Kit Charger
(Optional accesory)
It is sed to power the
MTB200 with the
battery o tp t on the
vehicle
External Battery Kit
(Optional accesory)
It is a set of
accesories incl de an
external battery, a
power control nit and
a pelican waterproof
casing. It will greatly
improve the working
time of MTB200 and
also let the MTB200
can be sed for some
special application like
container tracking.

NU
_
MTB200
_
001_05112013_EN
Date: 05.11.2013 Page 10 / 14
MTB200 Data Cable
(Optional accessory)
„CA80189“
It is the USB data
cable which can be
sed for firmware
pgrading and
config ration.
MTB200 External Cable
(Optional accessory)
It is the extend cable
which incl de the
charger interface and
external battery
interface on MTB200.
It also incl des the
ignition detection
interface on the
MTB200
MTB200 External GPS
Active Antenna
(Optional accessory)
External GPS active
antenna is optional
according to
application scenarios
MTB200 Holder Witho t
Magnet
(Optional accessory)
It is sed to hold the
MTB200, mo nt to
somewhere with the
screw
MTB200 Holder With
Magnet
(Optional accessory)
It is sed to hold the
MTB200, attached to
metal with the magnet
on it