Monogram ZGG420NBPSS User manual

monogram.com
69
Built-in grills
Dual-burner cooktopFree-standing grills
Built-in outdoor grills
General features
Heavy-duty, 304 stainless steel construction with Professional styling complements Monogram®
ranges and other cooking products, allowing a seamless transition between indoor and outdoor
spaces.
Double-wall design insulates the canopy to minimize heat loss and allow for cooler surfaces.
25,000-BTU stainless steel burners offer precise temperature control, and the Gourmet Radiant™
trays ensure even heat distribution and reduce flare-ups.
Ceramic-infrared rotisserie burner allows you to slow-roast meats to succulent perfection.
The rotisserie motor assembly plugs in and detaches easily for convenient cooking and storage.
23,000-BTU ceramic-infrared searing burner delivers the high radiant heat needed to sear the
outside of foods, locking in natural juices and flavors.
Integrated illumination sets the stage for nighttime grilling with red LED lights above the knob
controls, along with interior halogen lighting.
Grill liners are required for installation in a combustible enclosure. Order separately, ZX30JR for 30"
grills and ZX42JR for 42" grills.
42" built-in
outdoor grill
ZGG420NBPSS (natural gas)
Overall dimensions
(WxHxD in inches):
41-7/8 x 26 x 27
Approx. shipping wt. (lbs.) 334
• 23,000-BTU ceramic-infrared
sear burner
• 25,000-BTU stainless steel
burners
• Red LED lights above the
knob controls
• Halogen interior lighting
• Ceramic-infrared rotisserie
burner
30" built-in
outdoor grill
ZGG300NBPSS (natural gas)
Overall dimensions
(WxHxD in inches):
29-7/8 x 26 x 27
Approx. shipping wt. (lbs.) 253
• 23,000-BTU ceramic-infrared
sear burner
• 25,000-BTU stainless steel
burners
• Red LED lights above the
knob controls
• Halogen interior lighting
• Ceramic-infrared rotisserie
burner

70
Advance planning for built-in outdoor grills
These grills are factory set for natural gas operation.
A conversion kit is available if liquid propane is preferred;
order WB28X10117.
High-altitude kit WB28X10119 is available for operation above
2,000 feet. Order WB28X10118 to change the connection from
LP portable (20-lb. tank) to whole-house stationary tank or to
change a stationary tank to portable.
Conversion kit must be installed by a qualified service technician
at additional cost. Order this kit from your Monogram®supplier.
Side view, all built-in grill models
*The weight of the grill is fully supported by
the side trims. The back of the grill overlaps
the back edge of the cutout.
10-1/4" from
Bottom of
Support Flange
*25-1/2"
Countertop Depth
27" to Front
of Control Panel
28-1/2" to Front of Bullnose
42"-wide built-in grill
ZGG420NBPSS
41-7/8"
12" Min. to Combustibles
4" Min. Clearance for Lid
to Non-Combustibles
27"
26"
40-3/4"
36"
Min. 1-1/8" Min.
10-7/8"
24-1/2"
Grill Cutout
Gas and
Electrical
Locations
Opening
for Optional
Access Doors
30"-wide built-in grill
ZGG300NBPSS
29-7/8"
12" Min. to Combustibles
4" Min. Clearance for Lid
to Non-Combustibles
27"
26"
28-3/4"
36"
Min. 1-1/8" Min.
10-7/8"
24-1/2"
Grill Cutout
Gas and
Electrical
Locations
Opening
for Optional
Access Doors

monogram.com
71
Built-in grills
Dual-burner cooktopFree-standing grills
Advance planning for built-in outdoor grills
Installation in a combustible enclosure
To install into combustible enclosures, built-in outdoor grills must
use a grill liner accessory. Please refer to the grill liner installa-
tion instructions for details.
Dimensions and installation information (in inches)
Built-in grill cut-out dimensions to install into combustible
enclosures with grill liner accessory (not provided with built-in grill)
These grills are designed to be installed into a non-combustible
enclosure when not using grill liner accessories.
• The grill drops into the opening and hangs from the side flanges.
It does not require support from the bottom.
• The cutout must be completely covered with non-combustible
material such as stone, brick, ceramic tile, concrete board, etc.
The countertop surface and edges must be flat and level.
• If the countertop has an
overhang, it must be notched
or cut back flush with the front
face of the cabinet below.
• Allow at least 12" minimum
clearance at the back of the grill
when the exhaust is directed
to a window or surface that is
difficult to clean. Allow at least 4" clearance behind the grill to
allow the hood lid to open.
• Allow 12" minimum clearance on both sides and the back of
the grill to adjacent vertical combustible construction.
• These gas grills cannot be used below any type of overhead
construction.
• These grills are designed for outdoor use only. Do not locate
the grill or cooktop in a building, garage or other enclosed or
semi-enclosed area.
• Locate the back side of the grill away from prevailing winds
and avoid cooking in windy conditions.
Countertop Notch Detail
5/8" for Outdoor Grills
1-1/2" Depth
Depth to Cabinet Face
4" square holes for gas and
electrical connections both left
and right sides (rear or bottom
access). Make these holes
in the frame based on your
requirements.
Insulated
Liner
Combustible
Enclosure
ZGG420NBPSS (natural gas)
Description
Kit model
number
Dimensions with
insulated jacket installed
a b c d e f
30" grill liner ZX30JR 36" 5" 26-1/2" 4-1/2" 311-5/8"
42" grill liner ZX42JR 48" 5" 26-1/2" 4-1/2" 311-5/8"

72
Advance planning for built-in outdoor grills
ZX27AD, Double access doors
Double access doors may be installed directly below a grill. The
support frame fits into the opening and the doors hang from
side hinges.
When installing into an
enclosure and adjacent to
other accessories, measure
and cut the openings to
align them evenly across
the bottom. The access door
frame overlap at the bottom
of the cutout is 7/8". See
cutout dimensions below.