Montigo DelRay DRL3613NI Instruction Manual

XG0226 - 180904
Installation & Maintenance Manual
• Theinstallationofthisreplacemustbedonebya
qualiedandcertiedgasapplianceinstaller.
• Checklocalcodesandreadallinstructionspriorto
installation.
®
C
US
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury,
death, or property damage.
—Donotstoreorusegasolineorotherammablevaporsand
liquidsinthevicinityofthisoranyotherappliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phoneinyourbuilding.
• Leavethebuildingimmediately.
• Immediatelycallyourgassupplierfromaneighbour's
phone. Follow the gas supplier’s instructions.
• Ifyoucannotreachyourgassupplier,callthere
department.
—Installationandservicemustbeperformedbyaqualied
installer,serviceagencyorthegastter.
DelRay INDOOR DIRECT VENT GAS FIREPLACE
DRL3613NI 16,000 BTU/hr Natural Gas or Propane Gas
DR3613NI-2 16,000 BTU/hr Natural Gas or Propane Gas
Read and understand this manual. Improper installation, adjustment,
alteration, service or maintenance can cause serious injury, property
damage or even death. For assistance or additional information
consult a qualied installer, service agency or the gas supplier.
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and
shall be installed for the protection of children and other
at-risk individuals.
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
Installation and service must be performed by a qualied installer,
service agency or the gas tter.
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for suture reference.
NOTICE
CAUTION
DANGER
WARNING
DANGER

XG0226 - 1809042
General
Congratulations on your purchase of a Montigo Fireplace.
With over 30 years of experience, Montigo is committed to providing
you with a gas fireplace that is not only a beautiful addition to your
space, but that is also designed and manufactured to the highest
safety, reliability and engineering standards.
We strongly encourage you to read and carefully follow the
instructions laid out in this Installation, Operation and Maintenance
Manual and retain it for your future reference. Pay special attention
to all cautions, warnings, and notices throughout this manual
intended to ensure your safety.
This manual covers installation, operation and maintenance. Lighting,
operation and care of this replace can be easily performed by the
homeowner. All installation and service work should be performed
by a qualied or licensed installer, plumber or gas tter as certied
by the state, province, region or governing body where the replace
is being installed.
This installation, operation and maintenance manual is applicable
to the models described in Table 1. Refer to your rating plate to
verify included options.
Warranty and Installation Information: (See Appendix B)
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
• Modication of the replace and/or components including Direct-
Vent assembly or glass doors.
• Use of any component part not manufactured or approved by
Montigo in combination with this Montigo replace system.
• Installation other than as instructed in this manual.
• Consult your local Gas Inspection Branch on installation
requirements for factory-built gas replaces. Installation & repairs
should be done by a qualied contractor.
MODEL Natural Gas Propane (with conv. kit) Gas Rating (BTU hr) Linear Burner w/ Glass Accessories SIT Electronic Ignition
DRL3613NI X 16,000 X X
DR3613NI-2 X 16,000 X X
DRL3613LI X 16,000 X X
DR3613LI-2 X 16,000 X X
Introduction
Safety Alert Key
Indicates a hazardous situation which, if
not avoided, WILL result in death or serious
injury or property damage.
Indicates a hazardous situation which, if not
avoided, WILL result in minor or moderate
injury.
Indicates a hazardous situation which, if not
avoided, COULD result in death or serious
injury or property damage.
Indicates practices that are important, but
not related to personal injury.
DANGER
CAUTION
WARNING
NOTICE
Figure 1 DR and DR Builders Specications

XG0226 - 180904 3
General
Contents
Safety Alert Key.................................................................................. 2
Introduction ....................................................................................... 2
Section A: Before You Begin .......................................................................4
Installation Checklist ......................................................................................4
Standard Installation Checklist....................................................................5
Rating Plate Sample .......................................................................................6
Section 1: Dimensions ....................................................................... 6
DelRay Dimensions ........................................................................................6
Section 2: Framing ............................................................................ 7
In Wall and Corner Dimensions..................................................................7
Alcove above the fireplace ...........................................................................7
Clearances........................................................................................................8
Section 3: Venting .............................................................................. 8
Section 3-3-1: Venting Layout ........................................................... 9
Wall and Roof mounted venting .................................................................9
Section 3-2: Installing a Roof Mounted Direct Vent Termination
for4''/7''(MVTK-1)............................................................................ 10
Section 3-2-1: Venting Layout ...................................................................10
Section3-3:InstallingaWallMountedTermination4''/7'' .........11
Section 3-3-2: Venting Components........................................................12
Section 3-3-2.2: Duravent DirectVent Pro 4” x 6⅝” Venting Compo-
nents................................................................................................................13
45° Corner Installation 4''/7'': ....................................................................14
45° or less Corner Installation 4''/7'':.......................................................14
Section3-3-3:HeatShields4''/7''.................................................... 15
Section 4: Wiring .............................................................................. 16
DR3613 (N/L) I-2 Wiring Diagram .............................................................16
Installation of Electrical Supply .................................................................16
Installation of the wall switch.....................................................................16
DRL3613 (N/L) I Wiring Diagram...............................................................17
Installation of the wall switch.....................................................................17
CPI[ContinuousPilotIgnition]/IPI[IntermittentPilotIgnition]
JumperCableInstallation ............................................................... 18
“Why use CPI mode”?...................................................................................18
The difference between IPI and CPI:........................................................18
Installing the CPI Jumper Cable.................................................................18
Section 5: Installing the gas line..................................................... 19
Fuel Type.........................................................................................................19
Gas Pressure .................................................................................................19
Section 5-3: GAS CONNECTION................................................................19
Section 6: Finishing .......................................................................... 20
Finishing Around the Fireplace .................................................................20
Cement Board Install...................................................................................20
Section8:Removing&InstallingtheScreen/Door .................... 21
Removing the Screen...................................................................................21
Reinstalling the Screen................................................................................21
Removing the door ......................................................................................21
Reinstalling the door....................................................................................21
PropaneConversion ........................................................................ 22
Section 9: Installing the Accessories.............................................. 24
Installing the Firestones or optional Fireglass ......................................24
Section 10: Cleaning and Maintenance ........................................ 26
General............................................................................................................26
Cleaning ..........................................................................................................26
Pilot Burner Adjustment. ............................................................................26
Troubleshooting............................................................................................27
Replacement Parts.......................................................................................27
Appendix A: Venting Terminations................................................ 28
Appendix B: Warranty ..................................................................... 29
Appendix B: Warranty Continued .................................................. 30
Appendix C: Amendment ................................................................ 31
(GasFireplace/EquipmentsoldintheStateofMassachusetts)31

XG0226 - 1809044
General
IMPORTANT MESSAGE: SAVE THESE INSTRUCTIONS
The DelRay replaces must be installed in accordance with these
instructions. Carefully read all the instructions in this manual rst.
Consult the Local Gas Branch to determine the need for a permit prior
to starting the installation. It is the responsibility of the installer to
ensure this replace is installed in compliance with the manufacturers
instructions and all applicable codes.
Installation Checklist
• Determine the desired install location of your replace.
• See Section 1, Dimensions on Page 6, and refer to the Framing
Section 2 for details.
• Select the location of your termination and resulting vent run.
• Should it be impossible to meet the venting requirements laid out
in Section 3: Venting, please contact your Montigo dealer regarding
the use of a Montigo Power Vent.
• Lay out the Vent run; calculating the required elbows and straight
runs of 4"/7" ex and/or rigid pipe.
• Layout Electrical Requirements refer to Section 4: Wiring, for Details.
• Refer to Section 5: Installing the Gas Line, for details on the gas
connection and access.
• Refer to local codes and guidelines for installation requirements.
• Installation and repairs should be done by a qualied contractor
and must conform to:
• Installations in Canada must conform to the local codes or in the
absence of local codes to the current version of Natural Gas and
Propane Installation Code, CSA B149. Electrical installations must
conform to the local codes or, in the absence of local codes, to the
current version of Canadian Electrical Code, CSA C22.1.1
• Installations in the USA must conform to the local codes or in the
absence of local codes to the current version of National Fuel Gas
Code, ANSI Z223.1/NFPA 54. Electrical installations must conform
to the local codes or, in the absence of local codes, to the current
version of the National Electrical Code, ANSI/NFPA 70. See Appendix
C for installation within the State of Massachusetts
Do not use this appliance if any part has been under water.
Immediately call a qualied service technician to inspect the appliance
and to replace any part of the control system and any gas control that
has been under water
Due to high temperatures, the appliance should be located out of
trac and away from furniture and draperies
Children and adults should be alerted to the hazards of high surface
temperature and should stay away to avoid burns or clothing ignition
A barrier designed to reduce the risk of burns from the hot viewing
glass is provided with this appliance and shall be installed for the
protection of children and other at-risk individuals
Clothing or other ammable material should not be placed on or near
the appliance
Installation and repair should be done by a qualied service person.
The appliance should be inspected before use and at least annually
by a professional service person. More frequent cleaning might be
required due to excessive lint from carpeting, bedding material, etc. It
is imperative that control compartments, burners, and circulating air
passageways of the appliance be kept clean
NOTICE
NOTICE
NOTICE
NOTICE NOTICE
NOTICE
Section A: Before You Begin

XG0226 - 180904 5
General
Standard Installation Checklist
This standard installation checklist is to be used by the installer in conjunction with, not instead of, the instructions contained within this
installation manual.
Customer Date Installed:
Install Address: Location of Fireplace:
Installer:
Model (circle one): DRL3613NI, DR3613NI-2 Dealer Phone:
Serial #:
*Only applicable for Builders Series
YES NO IF NO, WHY NOT?
Appliance Install: Section 2
Framing complies with install manual.
Standos have been installed.
Proper clearances have been maintained.
Venting: Section 3
Venting conguration complies with vent diagrams.
Venting installed, fastened, and secured in place maintaining proper clearance.
Firestops installed.
Exterior wall/roof ashing installed and sealed in compliance with local building code.
Terminations installed and sealed in compliance with local building code.
Direct vent termination is highest point in vent assembly.
Wiring/Electrical:Section4
Unswitched power provided to the appliance PPO box.
Low voltage wire connected to dry contact wall switch (non-powered)*
Gas: Section 5
Proper appliance for fuel type.
Was a conversion performed?
Leak check performed & inlet pressure veried.
Finishing: Section 6
Only non-combustible materials installed in non-combustible areas.
Clearances meet installation manual requirements
Mantels and/or projections comply with install manual
Appliance Setup: Section 7 through 9
Media, door, and screen installed according to install manual
Manual given to home owner.
Started appliance and veried no gas leaks exist.
Comments:

XG0226 - 1809046
General
Rating Plate Sample
DelRay Dimensions
Figure 1.1 Rating Plate for DelRay Figure 2. Fireplace dimensions (Tolerance ± ⅛").
Section 1: Dimensions
623
24 1
2"
373
14 11
16 "
927
36 1
2"
974
38 3
8"
1149
45 1
4"
1051
41 3
8"
312
12 5
16 "324
12 3
4"
1051
41 3
8"
974
38 3
8"
526
20 11
16 "
127
5"
422
16 5
8"
680
26 3
4"
166
69
16 "
312
12 5
16 "
127
5"
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
ITEM NO. PART NUMBER DESCRIPTION MATERIAL QTY. Revision
1 1-2 valve handle Material <not specified> 1
A
2 3-8 to 3-8 Safety Valve Material <not specified> 1
A
3 B038H GAS INLET INSERT C12L14 CDS 1 B
4 DL24013-10 3 Row Holes Top Burner 20 GA Aluminized steel 1 C
5 DL24015-20 Burner Baffle 26 GA Satin-Coated 1 B
6 DL24016-20 Base Media Burner 20 GA Aluminized steel 1 B
7 DL24017-10 Side Media Burner 18 GA Aluminized steel 2 B
8 DL63106-20 Door Spring Retainer 16 Ga. Satin Coat 2 B
9 DL63212-20 Door Latch 14 GA Satin 2 B
10 EBOX491 PO BOX OUTER COVER 22 Ga Satin 1 C
11 EBOX492 PO BOX INNER COVER 20 Ga Satin 1 B
12 EC1220 CLAMP CONNECTOR, 1/2", SL20C20 1 B
13 EC1466 Fan L/H Material <not specified> 1
A
14 GC3020 4 Batteries Holder. Material <not specified> 1
A
15 GC3089 Proflame Valve W?Stepper Motor NG 1
A
16 GF1012 Material <not specified> 1
A
17 GF1072 3/8OD X 12" LGTH FLEX HOSE Material <not specified> 1 A
18 GF1114 Shutoff, Valve, 3/8" Flare to 3/8" Flare Brass 2
19 GF2089 3/8" MPT to 3/8" Flare 90 deg Elbow 1 A
20 GF2089-a 7/16"-24 UNS-2B Nut Brass C37700 2
A
21 GF2097 MNR36-Sleeve DOM 1 1/2 OD 11GA 1 C
22 GF3043 PROPANE BURNER GAS INLET Carbon Steel 1 A
23 GL1118 Window Glass MNR36 5mm Tempered Glass 1 B
24 Glass Gasket Material <not specified> 1
A
25 HCOL010 4" COLLAR 22Ga. SATIN 1 3
26 HCOL014 4" PIPE 22Ga. SATIN 1
27 HCOL029 COLLAR, FLUTE, H34 22Ga. SATIN 1 B
28 HE38022-10 Wire Gasket Clamp
10 Ga. Hot Roll
1 A
29 HW1153 Door Retainer Bolt 2 0
30 HW1209 1
31 HW1232 Door Retainer Spring 1/2`` x 4.5``
ASTM A401
2 B
32 HW2032 1/4"NC Machine Nut 2 0
33 IN1125 Wire Gasket
CG365 1/4" (PSA 1 side
only)
1 B
34 IN1194 7" COLLAR GASKET 1/8 MANNIGLASS 1 B
35 IN1195 BURNER GASKET 1/8 MANNIGLASS 1 B
36 MNR36001-20 Burner Tray 18 GA Satin-Coated 1 H
37 MNR36002-20 7" COLLAR 22 GA Satin-Coated 1 A
38 MNR36003-20 Firebox Top 20 GA Satin-Coated 1 E
39 MNR36004-20 Back Top Spacer 20 GA Satin-Coated 1 B
40 MNR36006-20 Firebox Wrapper 20 GA Satin-Coated 1 J
41 MNR36007-20 Left Side 16 GA Satin-Coated 1 J
42 MNR36008-20 Right Side 16 GA Satin-Coated 1 I
43 MNR36009-10 Left & Right Spacer 20 GA Satin-Coated 2 C
44 MNR36010-20 Fire Box Foot 16 GA Satin-Coated 2
A
45 MNR36011-20 Lower Door Retainer 18 Ga Satin-Coated 1 B
46 MNR36012-20 Outside Skin Wrapper 22 GA Satin-Coated 1 D
47 MNR36013-20 Outer Bottom Skin 22 GA Satin-Coated 1 D
48 MNR36014-20 Outer Skin Top 22 GA Satin-Coated 1 D
49 MNR36015-20 Glass Door Frame 16 GA Satin-Coated 1 F
50 MNR36016-20 Front Panel 20 GA Satin-Coated 1 H
51 MNR36017-20 Side Front Panel Flange 20GA Satin-Coated 2 C
52 MNR36018-20 Valve Cover 18 GA Satin-Coated 1 D
53 MNR36019-20 Middle Back Bord Bracket 16 GA Satin-Coated 2
B
54 MNR36023-20 Back Bord & Tray Bracket 16 GA Satin-Coated 2 D
55 MNR36029-20 Firebox Top Support 20 GA Satin 2 A
56 MNR36030-10 Service Door 20 GA Satin 1 C
57 MNR36031-20 Media Tray Back 20 GA Satin 1 F
58 MNR36032 Safety Screen MNR36 Safety Mesh / Steel Frame 1 B
59 MNR36033-10 Screen Top Support 20 GA Satin-Coated 1 C
60 MNR36034-20 Safety Screen Handle 20 GA Satin-Coated 2 D
61 MNR36035-20 Media & Back Bord Tray Bracket 16 GA Satin-Coated 3 E
62 MNR36036-20 Media Tray Front 20 GA Satin 1 F
63 MNR36038-20 Back Wall 20GA Satin-Coated 1 C
64 MNR36039-20 Front Panel Flange 20GA Satin-Coated 2 E
65 MNR36040-10 7" Collar Cover 22 GA Satin-Coated 1 B
66 MNR36041-20 7" Pipe Bracket 22 GA Satin-Coated 2
A
67 MNR36042-10 Pilot Clip 20 GA Satin 1 B
68 MNR36045-20 Back Plate Side Flange 20GA Satin-Coated 2
A
69 MNR36046-20 Back side spacer 20GA Satin-Coated 2 B
70 MNR36047-10 Rock Tray CRSPERF316/20 2 H
71 MNR36048-20 Pilot Cover 20 GA 304 SS/P 1 D
72 MNR36049-20 Pilot Mounting Bracket 18 GA Satin-Coated 1 D
73 MNR36053-20 Fan Bracket 20 GA Satin 1 A
74 MNR36061-20 Glass Bottom Bracket 20 GA Satin 2
A
75 MNR36063-20 Glass Bracket 20 GA Satin-Coated 2 A
76 MNR36075-20 Gas Valve Base Bracket 18 GA Satin 1 C
77 MNR36076-20 Tray Clip 18 GA Satin 1
B
78 MNR36077-20 Control Drawer Slide 20 GA Satin-Coated 1 A
79 MNR36078-20 Drawer Slide Bracket 20 GA Satin 2 D
80 MNR36079-20 Gas Valve Bracket 16 GA Satin 1 A
81 MNR36081-20 Burner Clip 20 GA Satin 1
A
82 PPOBOXONLY Power Outlet Junction Box Steel 1 B
83 Velcro Velcro 2
A
84 sitpilot IPI SIT PILOT ASSY IPI GC3036 (NG) 1
SW-Folder Name(Folder Name)
Current project PDF, DXF Folder
Name
PART NUMBER Gauge Material Revision
1 Y:\Products\Residential Products\R&D Projects\DL72\Cad Drawings\ 1-2 valve handle Material <not specified> A
1 Y:\Products\Residential Products\R&D Projects\DL72\Cad Drawings\ 3-8 to 3-8 Material <not specified> A
1 Y:\CADD\COMMON PARTS\BURNERS\Mixers\ B038H C12L14 CDS B
1 Y:\CADD\BURNER\New Design May 2017\ DL24013-10 20 GA Aluminized steel C
1 Y:\CADD\BURNER\New Design May 2017\ DL24015-20 26 GA Satin-Coated B
1 Y:\CADD\BURNER\New Design May 2017\ DL24016-20 20 GA Aluminized steel B
2 Y:\CADD\BURNER\New Design May 2017\ DL24017-10 18 GA Aluminized steel B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ DL63106-20 16 Ga. Satin Coat B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ DL63212-20 14 GA Satin B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ EBOX491 22 Ga Satin C
1 Y:\CADD\2007 CADD\Parts\Electrical\ EBOX492 20 Ga Satin B
1 Y:\CADD\2007 CADD\Parts\Electrical\Strain Relief\ EC1220 B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ EC1466 Material <not specified> A
1 Y:\CADD\COMMON PARTS\Valves\ GC3020 Material <not specified> A
1 Y:\CADD\COMMON PARTS\Valves\ GC3089
A
1 Y:\CADD\COMMON PARTS\Gas Fittings\ GF1012 Material <not specified> A
1 Y:\CADD\42\PL42VO\ GF1072 0.03 Material <not specified> A
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ GF1114 Brass
1 Y:\CADD\COMMON PARTS\Gas Fittings\ GF2089 A
2 Y:\CADD\COMMON PARTS\Gas Fittings\ GF2089-a Brass C37700 A
1 Y:\CADD\COMMON PARTS\BURNERS\Mixers\ GF2097 DOM 1 1/2 OD 11GA C
1 Y:\CADD\COMMON PARTS\BURNERS\Mixers\ GF3043 Carbon Steel A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ GL1118 5mm Tempered Glass B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ Glass Gasket Material <not specified> A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HCOL010 22Ga. SATIN 3
1
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HCOL014 22Ga. SATIN
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HCOL029 22Ga. SATIN B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HE38022-10
10 Ga. Hot Roll
A
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HW1153 0
1
Y:\CADD\COMMON PARTS\Hardware\Washers\ HW1209
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HW1232
ASTM A401
B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HW2032 0
1
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ IN1125 CG365 1/4" (PSA 1 side only) B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ IN1194 1/8 MANNIGLASS B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ IN1195 1/8 MANNIGLASS B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36001-20 18 GA Satin-Coated H
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36002-20 22 GA Satin-Coated A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36003-20 20 GA Satin-Coated E
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36004-20 20 GA Satin-Coated B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36006-20 20 GA Satin-Coated J
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36007-20 16 GA Satin-Coated J
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36008-20 16 GA Satin-Coated I
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36009-10 20 GA Satin-Coated C
2
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36010-20 16 GA Satin-Coated A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36011-20 18 Ga Satin-Coated B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36012-20 22 GA Satin-Coated D
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36013-20 22 GA Satin-Coated D
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36014-20 22 GA Satin-Coated D
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36015-20 16 GA Satin-Coated F
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36016-20 20 GA Satin-Coated H
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36017-20 20GA Satin-Coated C
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36018-20 18 GA Satin-Coated D
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36019-20 16 GA Satin-Coated B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36023-20 16 GA Satin-Coated D
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36029-20 20 GA Satin A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36030-10 20 GA Satin C
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36031-20 20 GA Satin F
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36032 Safety Mesh / Steel Frame B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36033-10 20 GA Satin-Coated C
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36034-20 20 GA Satin-Coated D
3 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36035-20 16 GA Satin-Coated E
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36036-20 20 GA Satin F
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36038-20 20GA Satin-Coated C
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36039-20 20GA Satin-Coated E
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36040-10 22 GA Satin-Coated B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36041-20 22 GA Satin-Coated A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36042-10 20 GA Satin B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36045-20 20GA Satin-Coated A
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36046-20 20GA Satin-Coated B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36047-10 CRSPERF316/20 H
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36048-20 20 GA 304 SS/P D
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36049-20 18 GA Satin-Coated D
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36053-20 20 GA Satin A
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36061-20 20 GA Satin A
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36063-20 20 GA Satin-Coated A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36075-20 18 GA Satin C
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36076-20 18 GA Satin B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36077-20 20 GA Satin-Coated A
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36078-20 20 GA Satin D
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36079-20 16 GA Satin A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36081-20 20 GA Satin A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ PPOBOXONLY Steel B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ Velcro A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ sitpilot IPI
1:12
DWG. NO.
SHEET 1 OF 1
WEIGHT:
MNR36 FULL ASSEMBLEY
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\MNR36 FULL ASSEMBLEY
October-11-18 12:10:40 PM
SCALE
DM
Description
MNR36 Full Assembly
Revision
14/07/2017
623
24 1
2"
373
14 11
16 "
927
36 1
2"
974
38 3
8"
1149
45 1
4"
1051
41 3
8"
312
12 5
16 "324
12 3
4"
1051
41 3
8"
974
38 3
8"
526
20 11
16 "
127
5"
422
16 5
8"
680
26 3
4"
166
69
16 "
312
12 5
16 "
127
5"
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
ITEM NO. PART NUMBER DESCRIPTION MATERIAL QTY. Revision
1 1-2 valve handle Material <not specified> 1
A
2 3-8 to 3-8 Safety Valve Material <not specified> 1
A
3 B038H GAS INLET INSERT C12L14 CDS 1 B
4 DL24013-10 3 Row Holes Top Burner 20 GA Aluminized steel 1 C
5 DL24015-20 Burner Baffle 26 GA Satin-Coated 1 B
6 DL24016-20 Base Media Burner 20 GA Aluminized steel 1 B
7 DL24017-10 Side Media Burner 18 GA Aluminized steel 2 B
8 DL63106-20 Door Spring Retainer 16 Ga. Satin Coat 2 B
9 DL63212-20 Door Latch 14 GA Satin 2 B
10 EBOX491 PO BOX OUTER COVER 22 Ga Satin 1 C
11 EBOX492 PO BOX INNER COVER 20 Ga Satin 1 B
12 EC1220 CLAMP CONNECTOR, 1/2", SL20C20 1 B
13 EC1466 Fan L/H Material <not specified> 1
A
14 GC3020 4 Batteries Holder. Material <not specified> 1
A
15 GC3089 Proflame Valve W?Stepper Motor NG 1
A
16 GF1012 Material <not specified> 1
A
17 GF1072 3/8OD X 12" LGTH FLEX HOSE Material <not specified> 1 A
18 GF1114 Shutoff, Valve, 3/8" Flare to 3/8" Flare Brass 2
19 GF2089 3/8" MPT to 3/8" Flare 90 deg Elbow 1 A
20 GF2089-a 7/16"-24 UNS-2B Nut Brass C37700 2
A
21 GF2097 MNR36-Sleeve DOM 1 1/2 OD 11GA 1 C
22 GF3043 PROPANE BURNER GAS INLET Carbon Steel 1 A
23 GL1118 Window Glass MNR36 5mm Tempered Glass 1 B
24 Glass Gasket Material <not specified> 1
A
25 HCOL010 4" COLLAR 22Ga. SATIN 1 3
26 HCOL014 4" PIPE 22Ga. SATIN 1
27 HCOL029 COLLAR, FLUTE, H34 22Ga. SATIN 1 B
28 HE38022-10 Wire Gasket Clamp
10 Ga. Hot Roll
1 A
29 HW1153 Door Retainer Bolt 2 0
30 HW1209 1
31 HW1232 Door Retainer Spring 1/2`` x 4.5``
ASTM A401
2 B
32 HW2032 1/4"NC Machine Nut 2 0
33 IN1125 Wire Gasket
CG365 1/4" (PSA 1 side
only)
1 B
34 IN1194 7" COLLAR GASKET 1/8 MANNIGLASS 1 B
35 IN1195 BURNER GASKET 1/8 MANNIGLASS 1 B
36 MNR36001-20 Burner Tray 18 GA Satin-Coated 1 H
37 MNR36002-20 7" COLLAR 22 GA Satin-Coated 1 A
38 MNR36003-20 Firebox Top 20 GA Satin-Coated 1 E
39 MNR36004-20 Back Top Spacer 20 GA Satin-Coated 1 B
40 MNR36006-20 Firebox Wrapper 20 GA Satin-Coated 1 J
41 MNR36007-20 Left Side 16 GA Satin-Coated 1 J
42 MNR36008-20 Right Side 16 GA Satin-Coated 1 I
43 MNR36009-10 Left & Right Spacer 20 GA Satin-Coated 2 C
44 MNR36010-20 Fire Box Foot 16 GA Satin-Coated 2
A
45 MNR36011-20 Lower Door Retainer 18 Ga Satin-Coated 1 B
46 MNR36012-20 Outside Skin Wrapper 22 GA Satin-Coated 1 D
47 MNR36013-20 Outer Bottom Skin 22 GA Satin-Coated 1 D
48 MNR36014-20 Outer Skin Top 22 GA Satin-Coated 1 D
49 MNR36015-20 Glass Door Frame 16 GA Satin-Coated 1 F
50 MNR36016-20 Front Panel 20 GA Satin-Coated 1 H
51 MNR36017-20 Side Front Panel Flange 20GA Satin-Coated 2 C
52 MNR36018-20 Valve Cover 18 GA Satin-Coated 1 D
53 MNR36019-20 Middle Back Bord Bracket 16 GA Satin-Coated 2
B
54 MNR36023-20 Back Bord & Tray Bracket 16 GA Satin-Coated 2 D
55 MNR36029-20 Firebox Top Support 20 GA Satin 2 A
56 MNR36030-10 Service Door 20 GA Satin 1 C
57 MNR36031-20 Media Tray Back 20 GA Satin 1 F
58 MNR36032 Safety Screen MNR36 Safety Mesh / Steel Frame 1 B
59 MNR36033-10 Screen Top Support 20 GA Satin-Coated 1 C
60 MNR36034-20 Safety Screen Handle 20 GA Satin-Coated 2 D
61 MNR36035-20 Media & Back Bord Tray Bracket 16 GA Satin-Coated 3 E
62 MNR36036-20 Media Tray Front 20 GA Satin 1 F
63 MNR36038-20 Back Wall 20GA Satin-Coated 1 C
64 MNR36039-20 Front Panel Flange 20GA Satin-Coated 2 E
65 MNR36040-10 7" Collar Cover 22 GA Satin-Coated 1 B
66 MNR36041-20 7" Pipe Bracket 22 GA Satin-Coated 2
A
67 MNR36042-10 Pilot Clip 20 GA Satin 1 B
68 MNR36045-20 Back Plate Side Flange 20GA Satin-Coated 2
A
69 MNR36046-20 Back side spacer 20GA Satin-Coated 2 B
70 MNR36047-10 Rock Tray CRSPERF316/20 2 H
71 MNR36048-20 Pilot Cover 20 GA 304 SS/P 1 D
72 MNR36049-20 Pilot Mounting Bracket 18 GA Satin-Coated 1 D
73 MNR36053-20 Fan Bracket 20 GA Satin 1 A
74 MNR36061-20 Glass Bottom Bracket 20 GA Satin 2
A
75 MNR36063-20 Glass Bracket 20 GA Satin-Coated 2 A
76 MNR36075-20 Gas Valve Base Bracket 18 GA Satin 1 C
77 MNR36076-20 Tray Clip 18 GA Satin 1
B
78 MNR36077-20 Control Drawer Slide 20 GA Satin-Coated 1 A
79 MNR36078-20 Drawer Slide Bracket 20 GA Satin 2 D
80 MNR36079-20 Gas Valve Bracket 16 GA Satin 1 A
81 MNR36081-20 Burner Clip 20 GA Satin 1
A
82 PPOBOXONLY Power Outlet Junction Box Steel 1 B
83 Velcro Velcro 2
A
84 sitpilot IPI SIT PILOT ASSY IPI GC3036 (NG) 1
SW-Folder Name(Folder Name)
Current project PDF, DXF Folder
Name
PART NUMBER Gauge Material Revision
1 Y:\Products\Residential Products\R&D Projects\DL72\Cad Drawings\ 1-2 valve handle Material <not specified> A
1 Y:\Products\Residential Products\R&D Projects\DL72\Cad Drawings\ 3-8 to 3-8 Material <not specified> A
1 Y:\CADD\COMMON PARTS\BURNERS\Mixers\ B038H C12L14 CDS B
1 Y:\CADD\BURNER\New Design May 2017\ DL24013-10 20 GA Aluminized steel C
1 Y:\CADD\BURNER\New Design May 2017\ DL24015-20 26 GA Satin-Coated B
1 Y:\CADD\BURNER\New Design May 2017\ DL24016-20 20 GA Aluminized steel B
2 Y:\CADD\BURNER\New Design May 2017\ DL24017-10 18 GA Aluminized steel B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ DL63106-20 16 Ga. Satin Coat B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ DL63212-20 14 GA Satin B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ EBOX491 22 Ga Satin C
1 Y:\CADD\2007 CADD\Parts\Electrical\ EBOX492 20 Ga Satin B
1 Y:\CADD\2007 CADD\Parts\Electrical\Strain Relief\ EC1220 B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ EC1466 Material <not specified> A
1 Y:\CADD\COMMON PARTS\Valves\ GC3020 Material <not specified> A
1 Y:\CADD\COMMON PARTS\Valves\ GC3089
A
1 Y:\CADD\COMMON PARTS\Gas Fittings\ GF1012 Material <not specified> A
1 Y:\CADD\42\PL42VO\ GF1072 0.03 Material <not specified> A
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ GF1114 Brass
1 Y:\CADD\COMMON PARTS\Gas Fittings\ GF2089 A
2 Y:\CADD\COMMON PARTS\Gas Fittings\ GF2089-a Brass C37700 A
1 Y:\CADD\COMMON PARTS\BURNERS\Mixers\ GF2097 DOM 1 1/2 OD 11GA C
1 Y:\CADD\COMMON PARTS\BURNERS\Mixers\ GF3043 Carbon Steel A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ GL1118 5mm Tempered Glass B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ Glass Gasket Material <not specified> A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HCOL010 22Ga. SATIN 3
1
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HCOL014 22Ga. SATIN
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HCOL029 22Ga. SATIN B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HE38022-10
10 Ga. Hot Roll
A
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HW1153 0
1
Y:\CADD\COMMON PARTS\Hardware\Washers\ HW1209
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HW1232
ASTM A401
B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ HW2032 0
1
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ IN1125 CG365 1/4" (PSA 1 side only) B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ IN1194 1/8 MANNIGLASS B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ IN1195 1/8 MANNIGLASS B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36001-20 18 GA Satin-Coated H
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36002-20 22 GA Satin-Coated A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36003-20 20 GA Satin-Coated E
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36004-20 20 GA Satin-Coated B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36006-20 20 GA Satin-Coated J
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36007-20 16 GA Satin-Coated J
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36008-20 16 GA Satin-Coated I
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36009-10 20 GA Satin-Coated C
2
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36010-20 16 GA Satin-Coated A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36011-20 18 Ga Satin-Coated B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36012-20 22 GA Satin-Coated D
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36013-20 22 GA Satin-Coated D
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36014-20 22 GA Satin-Coated D
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36015-20 16 GA Satin-Coated F
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36016-20 20 GA Satin-Coated H
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36017-20 20GA Satin-Coated C
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36018-20 18 GA Satin-Coated D
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36019-20 16 GA Satin-Coated B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36023-20 16 GA Satin-Coated D
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36029-20 20 GA Satin A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36030-10 20 GA Satin C
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36031-20 20 GA Satin F
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36032 Safety Mesh / Steel Frame B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36033-10 20 GA Satin-Coated C
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36034-20 20 GA Satin-Coated D
3 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36035-20 16 GA Satin-Coated E
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36036-20 20 GA Satin F
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36038-20 20GA Satin-Coated C
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36039-20 20GA Satin-Coated E
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36040-10 22 GA Satin-Coated B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36041-20 22 GA Satin-Coated A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36042-10 20 GA Satin B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36045-20 20GA Satin-Coated A
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36046-20 20GA Satin-Coated B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36047-10 CRSPERF316/20 H
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36048-20 20 GA 304 SS/P D
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36049-20 18 GA Satin-Coated D
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36053-20 20 GA Satin A
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36061-20 20 GA Satin A
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36063-20 20 GA Satin-Coated A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36075-20 18 GA Satin C
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36076-20 18 GA Satin B
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36077-20 20 GA Satin-Coated A
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36078-20 20 GA Satin D
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36079-20 16 GA Satin A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ MNR36081-20 20 GA Satin A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ PPOBOXONLY Steel B
2 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ Velcro A
1 Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\ sitpilot IPI
1:12
DWG. NO.
SHEET 1 OF 1
WEIGHT:
MNR36 FULL ASSEMBLEY
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\MNR36 FULL ASSEMBLEY
October-11-18 12:10:40 PM
SCALE
DM
Description
MNR36 Full Assembly
Revision
14/07/2017

7
Installation
XG0226 - 180904
Section 2: Framing
1). Frame in the enclosure for the unit with framing materials. The
framed opening for the assembled replace is 43⅜" wide, x 33
11/16" high x 14¼" deep
NOTE: When constructing the framed opening, please ensure there is
access to install the gas line when the unit is installed
* When sheetrock is used behind the replace, framing depth may be
increased by 1/2".
Clearances must be in accordance with local installation codes and
the requirements of the gas supplier
Figure 3. Framing dimensions (Straight wall & Corner Installation).
NOTICE
When this appliance is installed directly on ANY combustible other
than wood ooring (carpet, vinyl, etc.). It must be installed on an
equivalent wood or metal panel. This material must extend the full
width and depth of the appliance.
WARNING
In Wall and Corner Dimensions Alcoveabovethefireplace
Figure 3.d Combustible Framing for shelves over the replace
1" Min.
Non-combustible
materials.Alcove
overreplace
CeilingLevel
7.5" 10.5"
Door
Opening
Floor
Non-Combustible
header
Min.
84"
362
14 1
4"
1101.100
43 3
8"
856
33 11
16 "
1:32
DWG. NO.
SHEET 1 OF 3
WEIGHT:
MNR36 Framing Assembly
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
31/07/2018
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\MNR36 Framing Assembly
August-24-18 10:22:42 AM
SCALE
DM
Description
MNR36 Framing Assembly
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
12.700
1
2"
12.700
1
2"
1206
47 1
2"
1705
67 1
8"
1101.100
43 3
8"
1:32
DWG. NO.
SHEET 3 OF 3
WEIGHT:
MNR36 Framing Assembly
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
15/08/2018
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\MNR36\CAD Drawings\MNR36 Framing Corner Assembly
August-28-18 9:28:32 AM
SCALE
DM
Description
MNR36 Freaming Corner Assembly
Revision

8
Installation
XG0226 - 180904
Clearances
MODEL Top - Top vent† Rear Sides†† Floor Mantel Vent Pipe
DR3613NI
DR3613NI-2 21" 2" 2.5" 0" 6"
1'' all around
2" on the
horizontal
NOTES:
† Clearance from top of replace to a ceiling within the replace
enclosure.
†† Clearance to solid sides. Clearance to front framing studs is 1".
Refer to framing drawings.
Figure 4. Combustible Wall Clearances
When installing a shelf over the top of the replaces, the following
guidelines must be adhered to:
Section 3: Venting
Montigo oers a variety of direct venting and termination options. The
direct vent termination location MUST be selected such that it is the
highest point in the venting assembly. It should also be selected such
that it provides the shortest vent run possible. Should it be impossible
to ensure that the termination is the highest point or to meet the
venting guidelines laid out below please contact your Montigo dealer
to discuss power venting options.
Notes For Planning Venting:
• Venting originates from the top of the unit
• Venting can terminate through the roof or through an exterior wall.
• Refer to Appendix A - Termination Locations to ensure the planned
termination location is acceptable.
• Once the termination location has been established, refer to the
appropriate section below for installation details
• All replaces shipped from the factory are top vent.
• Silicone application is NOT required when joining Montigo vent
pipes and components.
Under no circumstances can Montigo ex venting be cut to
accommodate an installation. Use an alternative length to complete
your vent run.
NOTICE

9
Installation
XG0226 - 180904
Figure 4.bb Minimum Horizontal vent run (Rigid)
"A" on chart
"B" on chart
Horizontal
Maximum
H1+H2
10'
20'
Vertical
Minimum
V1+V2
4'
8'
21
2
1
4
6
8
10
12
14
16
18
20
22
24
26
28
30
34
4 6 8 10 12 14 16 18 20
Horizontal Run (ft.)
B
A
WallandRoofmountedventing
34'MAXIMUMVERTICALHEIGHT
20'MAXIMUMHORIZONTALOFFSETS
3 MAXIMUM 90° ELBOWS PERMITTED
Theminimumventsystemforhorizontalterminationmustconsistof:
10" vertical section and 90° Elbow of the top of the unit (16 1/8" measured
from top of the unit to center of elbow) . Then a 12" horozontal section.
Themaximumhorizontalventsystemconsistsof:
34’ vertical length with 3 - 90° bends and a 20’ horizontal length
(measured to center of pipe)
"A"MinimumHorizontalventrun:
10" vertical section and 90° Elbow of the top of the unit (16 1/8"
measured from top of the unit to center of elbow).
"B"MaximumVerticalventrun:
34’ vertical length with a roof termination, restrictor recommended.
"C"MaximumHorizontalventrun:
34’vertical lengthwith 3elbows, andthe maximum20feet horizontalrun.
H1
H2
V2
V1
Section 3-3-1: Venting Layout

10
Installation
XG0226 - 180904
Roof mounted terminations
The following details are some possible congurations for roof mounted
terminations. See below.
This section applies to installations where the direct vent termination
will be roof mounted.
Section 3-2-1: Venting Layout
Selection of components and details of venting lay out should adhere
to the following guidelines:
• The maximum termination point is 34’ above the replace (NOTE:
if the maximum termination height is used, the ame pattern may
be aected).
• The Vertical termination must be a minimum 2’ higher than where
the termination exits the roong materials, (asphalt shingles, cedar
shakes, etc). This distance should be measured from the high side of
the roof slope where the ue ashing intersects the roong materials.
• Terminationlocation mustbe aminimum 6’from amechanicalairinlet.
• For a more detailed diagram of allowed termination locations, see
Appendix A.
• A maximum of two osets (each oset is made up of 2-90° bends) may
be made for vertical vent runs. (2 45° bends are equivalent to 1 90°)
• Firestops must be installed as required by National & local codes.
• Ensure all horizontal runs are supported with a minimum of 3
supports per 10’ of venting.
• Install all roof ashing and storm collars as shown.
Figure 6. Top vent, roof mounted termination with no oset in vent run.
Figure 6.b Top vent, roof mounted with 1 oset (1 oset= two 90° bends).
Section 3-2: Installing a Roof Mounted Direct Vent
Terminationfor4''/7''(MVTK-1)
MVTK1 Termination
MVTK1 Termination
MVTK1 Termination
Storm collar
Storm collar
Storm collar
2' min
2' min
2' min
Support ring
Support ring
Support straps OR
Support ring and
plates
Support ring and
plates
Support plate
Support plate
Firestop
Firestop
Obstacle
Obstacle
Firestop
34' max
34' max
Roof ashing
Roof ashing
Roof ashing
Figure 6.c Top vent, roof mounted with 2 osets (1 oset= two 90° bends).
Firestop
34' max
Firestop