Montigo SIT-WIFI Instruction Manual

XG0681 - 090222
Installation & Maintenance Manual
• Theinstallationofthisreplacemustbedonebya
qualiedandcertiedgasapplianceinstaller.
• Checklocalcodesandreadallinstructionspriorto
installation.
®
C
US
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury,
death, or property damage.
—Donotstoreorusegasolineorotherammablevaporsand
liquidsinthevicinityofthisoranyotherappliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phoneinyourbuilding.
• Leavethebuildingimmediately.
• Immediatelycallyourgassupplierfromaneighbour's
phone. Follow the gas supplier’s instructions.
• Ifyoucannotreachyourgassupplier,callthere
department.
—Installationandservicemustbeperformedbyaqualied
installer,serviceagencyorthegastter.
SIT-WIFI
WIFI DONGLE
Read and understand this manual. Improper installation, adjustment,
alteration, service or maintenance can cause serious injury, property
damage or even death. For assistance or additional information
consult a qualied installer, service agency or the gas supplier.
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
Installation and service must be performed by a qualied installer,
service agency or the gas tter.
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
NOTICE
CAUTION
DANGER
WARNING

XG0681 - 0902222
General
Safety Alert Key
Indicates a hazardous situation which, if
not avoided, WILL result in death or serious
injury or property damage.
Indicates a hazardous situation which, if not
avoided, WILL result in minor or moderate
injury.
Indicates a hazardous situation which, if not
avoided, COULD result in death or serious
injury or property damage.
Indicates practices that are important, but
not related to personal injury.
DANGER
CAUTION
WARNING
NOTICE
IMPORTANT MESSAGE: SAVE THESE INSTRUCTIONS
• Please read all instructions carefully
• We strongly recommend that all electrical service work be
performed by a qualified electrical contractor.
• Check to ensure that all components required for installation are
included in your package.
What is needed
In order to operate the replace with the Proame Connect app via
WiFi, 4 components are needed. if any of these items are missing/not
installed then the wi connect process will not be successful.
IFCControlboard
SIT PN: 0.584.665
Montigo PN: GC3104
The control board must be the version with the electrical schematic
printed in green.
SITProame2Connectenabledremote
SIT PN: 0.584.080 (handheld remote)
Montigo PN: GC3105 (handheld remote)
SIT PN: 0.584.090 (wall mounted remote)
Montigo PN: EC1550 (wall mounted remote)
This can be identied by the "connect" icon on the upper right corner
of the label.
ProameConnectApp(notProameConnectPlus)
Android and iOS applications can be found in their respective stores:
Play Store and App Store.
WiFi Dongle
This is plugged into the diagnostic port of the IFC control board.
SIT PN: 0.584.526
Montigo PN: SIT-WIFI
Section A: Before You Begin

XG0681 - 090222 3
General
Dongle Installation
To install the Proame Connect kit it is necessary to turn o the gas
appliance and to disconnect the power supply, wait for the unit to
fully cool.
To the install the dongle:
1. Unless a compatible board is already installed, remove the old IFC
and replace it with the compatible IFC, (The dongle compatible
IFC boards are distinguished by their green schematic on the
front).
2. Connect the WiFi dongle tothe IFC with the provided cable through
X0A connector.
3. The dongle can be safely placed on the bottom of the replace,
take care to place it out of the way of components such as fans,
and the valve.
App Installation
Download the Proame Connect app from Google Play or the Apple
App Store.
MakesureyourmobiledeviceisconnectedtotheWiFinetwork
theWiFiDonglewillusepriortoconguration.
RED LED GREEN LED LED TIMING MEANING
Blinking Blinking Synchronized, period of 0,5 sec Error in ash memory
Blinking OFF Period of 0,5 sec Error in IFC reading
Blinking OFF Period of 1 sec Error in IFC writing
ON ON Working in AP mode
Blinking Blinking Alternately, period of 1 sec Connecting to the local WiFi network
OFF ON Connected and working normally
Blinking Blinking Together, period of 0,1 sec OTA update (optional)
To the reset the dongle:
1. Press and hold the reset
button until the green
and red LED’s are lit (5-10
seconds). The Dongle is
now in AP mode.

XG0681 - 0902224
General
Configure a fireplace with the app
(Android)
1. Put the dongle in conguration mode keeping the button pressed
until green and red lights turn on.
2. Connect the mobile device to the local WiFi network.
3. Press the "Congure new replace” button, located in the
hamburger menu of the app. Wait for the replace to be detected.
4. When the replace is detected, press the Next button.
5. Enter your WiFi password and press Next.
6. Insert a replace name and press Next.
7. If you want to use your replace with Virtual Assistants, please
insert below the 8-character pairing key that you received via
email. To get the key to use voice commands you need to register
your device on the registration web page, if you don't want to
use voice commands, leave the eld blank and press next.
8. The conguration procedure is completed.

XG0681 - 090222 5
General
Configure a fireplace with the app
(iPhone)
1. Put the dongle in conguration mode keeping the button pressed
until green and red lights turn on.
2. Connect the mobile device to the local WiFi network.
3. Press the "Congure new replace” button, located in the
hamburger menu of the app. Wait for the replace to be detected.
4. The application will ask you to connect to the 'Proame_AP' WiFi
network to continue the conguration by pressing ‘Join’.
5. Wait for the replace to be detected.
6. If the dongle fails to connect automatically to the Dongle's
WiFi network, the following message will appear:
7. This message is due either to the presence of outdated software
inside the dongle or to the fact that the Dongle is not in conguration.
If the Dongle is in conguration mode, the application waits the
smartphone to connect to the “PROFLAME_AP_XXXXXXXXXXXX”
WiFi network (Password:password),The user must connect
manually to this network by exiting from the Proame Connect
app and entering into the WiFi manager of the device. Her the
user must select the WiFi network of the replace to congure.
After this, the user has to go back to the Proame Connect app.
8. When the replace is detected, press the Next button.
9. Enter your WiFi password and press Next.
10. Insert a replace name and press Next.
11. If you want to use your replace with Virtual Assistants, please
insert below the 8-chars Pairing Key that you received by email.
To get the key to use voice commands you need to register your
device on the registration web page, if you don't want to use voice
commands, leave the eld blank and press next.
12. The conguration procedure is completed.

XG0681 - 0902226
General
Search for new fireplaces just
configured
Congured replaces, connected to the local WiFi network, must be
found by the application. The search procedure is needed to nd all
connected replaces. Once the replace is found by the app, this one
is saved and can be selected on the top right of the main page. The
replace can be selected even after closing and reopening the app,
without searching again. To search for new replaces, the user must
press “Manage devices” button. The selection window lists all known
replaces and allows the user to manage them. Selecting “Search”
button, the application performs a local network scan to update
congured replaces. When a new replace is found, it is inserted into
the list. Pressing the “x” button near the replace name, the replace is
removed. To delete all known replaces, the user must press “Delete
all” button. “Close” button closes the management window. All known
replaces, congured and found by the application, can be selected
from the management window or by the top right area of the main page.
Change temperature units
In the top left hamburger menu, the temperature unit switch changes
the temperature unit displayed in the whole application. All showed
temperatures in the application are converted, with the related
temperature unit.

XG0681 - 090222 7
General
Fireplace controls
All available controls of each replace are reachable from the main
page of the application. The displayed status reects the status of the
selected replace, showed on the top right area.
More users can control a replace at the same time. When a user
sends a command, this command is reected to all users working on
that replace.
In case voice commands byGoogle and Alexa are activated, to ensure the
smart assistants compatibility, each command sent by the application
updates the cloud state related to the selected replace. The state
modied over the local WiFi network by the application is reected
to the cloud, so the smart assistants know exactly what is the current
state of each replace.
Conversely, a command sent by the user by means of a smart assistant,
passing through the cloud AWS services, when received by the replace
is reected to all devices connected over the local WiFi network. All apps
connected to the replace are updated with each cloud command.

XG0681 - 090222
Installation & Maintenance Manual
SIT-WIFISIT-WIFI
WidongleWidongle