montpellier MDWBI6053 User manual

Please read these instructions carefully before attempting to install or use this appliance.
We recommend that you keep these instructions in a safe place for future reference.
Installation and Operating Instructions
THE PERFECT BALANCE OF FUNCTION AND STYLE
LAUNDRY - DISHWASHING - COOKING - COOLING
Built-In 60cm Dishwasher
MDWBI6053

Thank you for choosing this Montpellier appliance.
Our appliances have been designed to provide you with the best combination of style, reliability and performance to
give you years of trouble-free use.
You may be familiar with a similar product, but please take time to read these instructions carefully before installing
or using your appliance to ensure you get the most from your purchase.
We recommend that you keep this manual in a safe place for future
reference.
Your appliance is covered by a comprehensive two year Parts & Labour
Guarantee. In the unlikely event that you experience a problem with your
appliance, you can rest assured that you are fully protected against the cost of
repairs for the first 24 months . Please note that any claim must be
accompanied by the model reference number, serial number and proof of
purchase.
To activate your guarantee, you will need your product serial number. This can
be found inside your appliance.
NB: Please make sure that you keep a copy of your original sales invoice as this
will be needed if any service call is required.
There are three ways to register your Guarantee:
• Online: Visit the Support page on our website and complete the online
Product Registration form. www.montpellier-appliances.com
•By Post: Simply detach and fill in the form provided, attach a stamp and send
it in the post. Don't forget to include your e-mail address so that we can send
confirmation through to you.
By Phone: Contact our warranty registration department on 0808 1961388
Welcome
ACROSS ALL OUR MODELS
YEAR
GUARANTEE
PA R T S & L A B O U R
www.montpellier-appliances.com
•
EN - 2
Icon Type Meaning
WARNING Serious injury or death risk
RISK OF ELECTRIC SHOCK Dangerous voltage risk
FIRE Warning; Risk of fire / flammable materials
CAUTION Injury or property damage risk
IMPORTANT Operating the system correctly

EN - 3
CONTENTS
1 SAFETY INSTRUCTIONS .............................................................
1.1 General Safety Warnings ..........................................................................
1.2 Installation Warnings .................................................................................
1.3 During Usage..............................................................................................
2 INSTALLATION .............................................................................
2.1 Machine Positioning ...................................................................................
2.2 Water Connection .....................................................................................
2.3 Water Inlet Hose .......................................................................................
2.4 Drain Hose .................................................................................................
2.5 Electrical Connection ................................................................................
3 TECHNICAL SPECIFICATIONS ....................................................
3.1 General Appearance ..................................................................................
3.2 Technical Specifications ............................................................................
4 BEFORE USING THE APPLIANCE ..............................................
4.1 Preparing Your Dishwasher For First Use .................................................
4.2 Salt Usage .................................................................................................
4.3 Fill The Salt ................................................................................................
4.4 Test Strip ...................................................................................................
4.5 Water Hardness Table ...............................................................................
4.6 Water Softener System ..............................................................................
4.7 Setting ........................................................................................................
4.8 Detergent Usage ........................................................................................
4.9 Filling The Detergent ..................................................................................
4.10 Using Combined Detergents ....................................................................
4.11 Rinse-aid Usage .......................................................................................
4.12 Filling The Rinse-aid and Setting .............................................................
5 LOADING YOUR DISHWASHER ..................................................
5.1 Recommendations .....................................................................................
5.2 Upper Basket Height Adjustment................................................................
5.3 Alternative Basket Loads ..........................................................................
6 PROGRAMME TABLE ...................................................................
7 THE CONTROL PANEL .................................................................
7.1 Changing a Programme .............................................................................
7.2 Cancelling a Programme ...........................................................................
7.3 Switching The Machine Off .......................................................................
8 CLEANING AND MAINTENANCE ...................................................
8.1 Filters .........................................................................................................
8.2 Spray Arms ................................................................................................
8.3 Drain Pump.................................................................................................
9 TROUBLESHOOTING .................................................................
10 PRODUCT INFORMATION SHEET .............................................
11 HERE FOR YOU ...........................................................................
4
4
5
6
9
9
9
9
10
10
21
11
11
11
12
12
12
12
13
13
13
13
14
14
14
14
15
16
16
17
18
19
20
20
21
21
23
23
24
24
25
28
29
7.5 Save Power Mode .....................................................................................
7.4 Buzzer Sound Control ................................................................................
22

1 SAFETY INSTRUCTIONS
1.1 General Safety Warnings
•Read these instructions carefully before using your
appliance and keep this manual for future reference.
Please check the packaging of your machine before
installation and the outer surface of the machine once
the packaging has been removed. Do not operate the
machine if it appears damaged or if the packaging has
been opened.
•Packaging materials protect your machine from any
damage that might occur during transportation. The
packaging materials are environmentally friendly as
they are recyclable. Use of recycled material reduces
raw material consumption and decreases waste
production.
This appliance can be used by children aged from 8
years and above, and by persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning the use of the appliance in a safe
way and understand hazards involved. Children should
not be allowed to play with the appliance.
Remove packaging and keep it out of reach of
children.
Keep children away from detergents and rinse aids.
There may be some residue left in the machine after
washing. Keep children away from the machine when it
is open.
EN - 4

EN - 5
1.2 Installation Warnings
•Choose a suitable and safe place to install your
machine.
•Only original spare parts should be used with the
machine.
Unplug the machine before installation.
Your machine must only be installed by an
authorised service agent. Installation by anyone other
than an authorised agent may cause your warranty to
be void.
Check that the indoor electrical fuse system is
connected in line with safety regulations.
All electrical connections must match the values on
the plate.
Ensure the machine does not stand on
the electrical supply cable.
Never use an extension cord or a multiple
socket connection.
The plug should be accessible after the machine
is installed.
•After installation, run your machine unloaded for the
first time.
The machine must not be plugged in during
positioning.
Always use the coated plug supplied with your
machine.
If the electrical cable is damaged, it should
only be replaced by a qualified electrician.

EN - 6
•Connect the hose directly to the water inlet tap. The
pressure supplied by the tap should be a minimum of
0.03 MPa and a maximum of 1 MPa. If the pressure
exceeds 1 MPa, a pressure relief valve must be fitted
between the connection.
1.3 During Usage
•This machine is for domestic use only, do not use
it for other purposes. Commercial use will void the
guarantee.
Do not stand, sit or place loads on the open door of
the dishwasher.
Only use detergents and rinse aids produced
specifically designed for dishwashers. Our company
is not responsible for any damage that may occur
due to misuse.
Do not drink water from the machine.
Due to the danger of explosion, do not place any
chemical dissolving agents into the machine's
washing section.
•Check the heat-resistance of plastic items before
washing them in the machine.
Only put items in the machine which are suitable for
dishwashing, and take care not to overfill the
baskets.
Do not open the door while the machine is in
operation, hot water may spill out. Safety devices
ensure the machine stops if the door is opened.
The machine door should not be left open. It may
cause accidents.

EN - 7
•Some machine components and packaging consist of recyclable materials.
•Plastics are marked with the international abbreviations:(>PE<, >PP<, etc. )
•The cardboard parts consist of recycled paper. They can be put into waste paper
containers for recycling.
•Material unsuitable for domestic waste must be disposed of at recycling centres.
•Contact a relevant recycling centre to obtain information about disposal of
different materials.
PACKAGING AND THE ENVIRONMENT
• Packaging materials protect your machine from damage that may occur during
transportation. The packaging materials are environmentally friendly as they are
recyclable. The use of recycled material reduces raw material consumption and
therefore decreases waste production.
Place knives and other sharp objects in the
cutlery basket in a blade-down position.
In the case of a malfunction, repair should only
be performed by an authorised service company,
otherwise the warranty will be void.
Before repair work, the machine should be
disconnected from the mains. Do not pull the cable to
unplug the machine. Switch off the water tap.
Operation at a low voltage will cause a decline in
performance levels.
For safety, disconnect the plug once a program
has finished.
To avoid an electric shock, do not unplug the
machine with wet hands.
Pull the plug to disconnect the machine from
the mains, never pull on the cord.
RECYCLING

CE Declaration of Conformity
We declare that our products meet the applicable European Directives, Decisions and
Regulations and the requirements listed in the standards referenced.
Disposal of your old machine
The symbol on the product or on its packaging indicates that this product
may not be treated as household waste. Instead, it shall be handed over to
the applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling
of this product. For more detailed information about recycling of this
product, please contact your local city office, your household waste
disposal service or the shop where the product was purchased.
EN - 8

EN - 9
2 INSTALLATION
2.1 Machine Positioning
When positioning the machine, place it in
an area where dishes can be easily loaded
and unloaded. Do not put the machine in
an area where the ambient temperature
falls below 0°C.
Read all warnings located on the
packaging before removing the packaging
and positioning the machine.
Place the machine close to a water tap and
drain. Take into consideration that the
connections will not be altered once the
machine is in position.
Do not hold the machine by its door or
panel.
Leave an adequate distance around the
machine to allow ease of movement when
cleaning.
Ensure the water inlet and outlet
hoses are not squeezed or trapped
and that the machine does not stand on the
electrical cable or any hoses while
positioning.
Adjust the feet so the machine is level and
balanced. The machine should be placed
on a flat solid surface otherwise it will be
unstable and the door of the machine will
not close properly. It s not recommended to
fit the dishwasher on any kind of carpet or
carpet tiles.
2.2 Water Connection
We recommend fitting a filter to your water
inlet supply in order to prevent damage to
your machine due to contamination (sand,
rust, etc.) from indoor plumbing. This will
also help prevent yellowing and deposit
formation after washing.
Note: printing on the water inlet hose!
If models are marked with 25°, the water
temperature may be max. 25 °C (cold
water).
WARNING: Use the new water inlet
hose supplied with your machine, do not
use an old machine’s hose.
WARNING: Run water through the
new hose before connecting.
WARNING: Connect the hose
directly to the water inlet tap. The pressure
supplied by the tap should be a minimum
of 0.03 MPa and a maximum of 1 MPa. If
the pressure exceeds 1 MPa, a pressure
relief valve must be fitted between the
connection.
WARNING: After the connections are
made, turn the tap on fully and check
for water leaks at both the tap end and the
dishwasher end. Always turn off the water
inlet tap after a wash program has finished.
For all other models:
Cold water preferred; hot water
max. temperature 60 °C
2.3 Water Inlet Hose

EN - 10
2.4 Drain Hose
Connect the water drain hose directly to
water drain hole or to the sink outlet spigot.
This connection should be minimum 50 cm
and maximum 110 cm from floor that the
dishwasher is placed on.
IMPORTANT: Items will not wash
properly if a drain hose longer than 4m
is used.
2.5 Electrical Connection
WARNING: Your machine is set to
operate at 220-240 V. If the mains voltage
supply to your machine is 110 V, connect a
transformer of 110/220 V and 3000 W
between the electrical connection and the
appliance.
Connect the product to a
grounded outlet protected by a fuse
complying with the values in the
“Technical Specifications" table.
The earthed plug of the
machine must be connected to an
earthed outlet supplied by suitable
voltage and current.
In the absence of earthing
installation, an authorised electrician
should carry out an earthing
installation. In the case of use without
earthing installed, we will not be
responsible for any loss of use that may
occur.
The plug on this appliance
will incorporate 13A fuse.

EN - 11
3 TECHNICAL
SPECIFICATIONS
3.2 Technical Specifications
Capacity 13 place
settings
Dimensions
Height
Width
Depth
820-870(mm)
598(mm)
550(mm)
Operating
voltage /
frequency
220-240V
50 Hz
Total current 10(A)
Total power 1900(W)
Water supply pressure
Maximum:
1 (Mpa)
Minimum:
0.03 (Mpa)
12
3.1 General Appearance
1. Upper basket with racks
2. Upper spray arm
3. Lower basket
4. Lower spray arm
5. Filters
6. Rating plate
7. Control panel
8. Detergent and rinse-aid dispenser
9. Cutlery basket
10. Salt dispenser
11. Upper basket track latch
12. Mini Active Drying Unit: This system
provides better drying performance your
dishes.
6
1
2
3
4
5
7
8
9
11
10

EN - 12
4 BEFORE USING THE
APPLIANCE
4.1 Preparing Your
Dishwasher For First Use
•Make sure the electricity and supply
water specifications match the values
indicated in the installation
instructions for the machine.
•Remove all packaging material inside
the machine.
•Set the water softener level.
•Fill the rinse aid compartment..
4.2 Salt Usage
For a good washing function, the
dishwasher needs soft, i.e. less
calcareous water. Otherwise, White lime
residues will remain on the dishes and the
interior equipment. This will negatively
affect your machine’s washing, drying and
shining performance. When water flows
through the softener system, the ions
forming the hardness are removed from
the water and the water reaches the
softness required to obtain the best
washing result. Depending on the level of
hardness of the inflowing water, these ions
that harden the water accumulate rapidly
inside the softener system. Therefore, the
softener system has to be refreshed so
that it operates with the same
performance during every wash. For this
purpose, dishwasher salt is used.
The dishwasher can only use special
dishwasher salt to soften the water. Do not
use any small grained or powdered type of
salts which are easily soluble(for example
table salt). Using any other type of salt can
damage your machine.
4.3 Fill The Salt
To add softener salt,
(1) Open the salt compartment cap by
turning it counter clockwise.
(2) Remove salt cap.
(3) Before first use, fill the compartment
with 1 kg salt. If available, using a funnel
will make filling easier.
(4) Fill the container with water until it is
almost overflowing. Replace the cap
making sure it is secure and tight.
After every 20-30 Cycles, or when the
re-fill light indicates, add salt into your
machine until it fills up the container
(approx. 1 kg).
43
1 2
SALT
Only add water to the salt
compartment before first use.
Use softener salt specifically produced for
use in dishwashers.
When you start your dishwasher, the salt
compartment is filled with water, therefore
put the softener salt in prior to starting
your machine (see below for filling
instructions).
If the softener salt has overflowed and you
do not start the machine immediately, run
a short washing program to protect your
machine against corrosion.

4.4 Test Strip
Run water
through the
tap (1min.)
Keep the
strip in the
water (1sec)
Shake the
strip.
Wait
(1min.)
Set the hardness level of
your machine.
1
2
3
4
5
6
1
munite
1
second
1
munite
NOTE: The level is set to 3 as default. If the water is well water or has a hardness level
above 90 dF, we recommend that you use filter and refinement devices.
4.5 Water Hardness Table
4.6 Water Softener System
The dishwasher is equipped with a water softener which reduces the hardness in
the mains water supply. To find out the hardness level of your tap water, contact
your water company or use the test strip supplied.
4.7 Setting
In order to change the salt level, follow the below steps:
EN - 13
Level German dH French
dF
British
dE Indicator
1 0-5 0-9 0-6
2 6-11 10-20 7-14
3 12-17 21-30 15-21
4 18-22 31-40 22-28
5 23-31 41-55 29-39
6 32-50 56-90 40-63
P1-9h LEDs are on.
P2-9h LEDs are on.
1/2-9h LEDs are on.
3h-9h LEDs are on.
6h-9h LEDs are on.
P1-6h-9h LEDs are on.
• Open the door of the machine.
• Turn on the machine, and press the Programme button as soon as the machine
is turned on.
• Hold down the Programme button until all LED's blink once.
• The machine will display the last setting.
• Set the level by pressing the Programme button.
• Switch off the machine to save the setting.

EN - 14
DETERGENT
4.8 Detergent Usage
Only use detergents specifically designed for
domestic dishwashers. Keep your detergents
in cool, dry places out of reach of children.
Add the proper detergent for the selected
program to ensure the best performance. The
amount of detergent needed depends on the
cycle, load size, and soil level of dishes.
Do not fill detergent into the detergent
compartment more than required; otherwise
you can see whitish streaks or bluish layers
on glass and dishes and may cause glass
corrosion. Continued use of too much
detergent may cause machine damage.
Using little detergent can result in poor
cleaning and you can see whitish streaks in
hard water areas.
See the detergent manufacturer’s
instructions for a further information.
4.9 Filling The Detergent
Push the latch which will cause the dispenser
lid to slide upwards. Once fully open pour in
the required amount of detergent.
Close the lid by sliding it back over the
detergent and press it until it locks in place.
The dispenser should be refilled just before
the start of each programme.
4.10 Using Combined
Detergents
These products should be used according
to the manufacturer’s instructions.
Never put combined detergents into the
interior section or the cutlery basket.
Combined detergents contain not only
the detergent but also rinse-aid, salt
replacement substances and additional
components depending on the
combination. We recommend you do not
use combined detergents in short
programmes. Please use powder
detergents instead. If you encounter
problems when using combined detergents,
please contact the detergent manufacturer.
When using combined detergents, make
sure that water hardness and rinse aid
settings are set to the correct level. If you
stop using combined detergents make sure
that the levels are adjusted accordingly.
4.11 Rinse-aid Usage
The rinse aid helps to dry the dishes
without streaks and stains. Rinse-aid is
required for stain-free utensils and clear
glasses. The rinse aid is automatically
released during the hot rinse phase.
If the rinse aid dosage setting is set too
low, whitish stains may remain on dishes
and dishes do not dry or wash properly.
If the rinse aid dosage setting is set too
high you can see bluish layers on glass,
dishes and the interior of the dishwasher.

EN - 15
4.12 Filling The Rinse-aid And Setting
To fill the rinse aid compartment, open the rinse-aid compartment cap. Fill the compartment
with rinse aid to the MAX level and then close the cap. Be careful not to overfill the rinse aid
compartment and wipe up any spills.
In order to change the rinse aid level, follow the below steps before
turning on the machine:
•Open the door of the machine.
•Turn on the machine, and press the Programme button as soon as the machine is
turned on.
•Hold down the Programme button until all LED's blink twice. Rinse aid setting follows
water hardness setting.
•The machine will display the last setting.
•Change the level by pressing the programme button.
•Switch off the machine to save the setting.
The factory setting is 4. If the dishes are not drying properly or are spotted, increase the
level. If blue stains form on your dishes, decrease the level.
Level Dispensed Dose Indicator
1
2
3
4
5
3 doses of rinse-aid dispensed
4 doses of rinse-aid dispensed
2 doses of rinse-aid dispensed
Rinse-aid NOT dispensed
1 dose of rinse-aid dispensed
P1-9h LEDs are on
P2-9h LEDs are on
1/2-9h LEDs are on
3h-9h LEDs are on
6h-9h LEDs are on

EN - 16
5 LOADING YOUR
DISHWASHER
For best results, follow these loading
guidelines.
Loading the household dishwasher up to the
capacity indicated by the manufacturer will
contribute to energy and water savings.
Manual pre-rinsing of tableware items leads
to increased water and energy consumption
and is not recommended. You can place
cups, glasses, stemware, small plates,
bowls, etc. in the upper basket. Do not lean
long glasses against one another as they
cannot remain steady and may be damaged.
When placing long stem glasses and
goblets, lean them against the basket edge
or rack and not against other items.
Place all containers such as cups, glasses
and pots into the dishwasher with the
opening facing downwards otherwise water
can collect on items.
If there is cutlery basket in machine, you are
recommended to use the cutlery grid in
order to obtain the best result. Place all large
(pots, pans, lids, plates, bowls etc.) and very
dirty items in the lower rack. Dishes and
cutlery should not be placed above each
other.
WARNING: Take care not to obstruct
the rotation of spray arms.
WARNING:Make sure after loading the
dishes do not prevent the opening of the
detergent dispenser.
Do not overload the drawers or
place dishes in the wrong basket.
WARNING: To avoid any possible
injuries, place long-handle and sharp-
pointed knives with their sharp points facing
down or horizontally on the baskets.
5.1 Recommendations
Remove any coarse residue on dishes
before placing the dishes in the machine.
Always try and start the machine with full
load.

EN - 17
5.2 Upper Basket Height
Adjustment.
Before adjusting the upper basket
make sure that the basket is empty.
Turn the Rail Stop Clips, at the ends of
the rails, to the sides to open them (as
shown in the image below), then pull out
and remove the basket.
Change the position of the wheels, then
reinstall the basket to the rail, making sure
to close the Rail Stop Clips.
When the upper basket is in the higher
position, larger items such as pans can be
placed on the lower basket.
Height Adjustable Rack (peg
type)
The height adjustable racks enable
glasses and cups to be placed on or
under the racks.
The racks can be adjusted to 2 different
heights.
Cutlery and utensils can also be placed on
the racks horizontally.
1
2

5.3 Alternative
Basket loads
Lower Basket
Upper Basket
Incorrect Loads
Incorrect loading can cause poor
washing and drying performance. Please
follow the manufacturer’s
recommendations for good performance
results.
Unsuitable Items For Dishwashing
•Cigarette ashes, candle leftovers,
polish, paint, chemical substances,
iron-alloy materials.
•Forks, spoons and knives with
wooden, bone, ivory or nacrecoated
handles; glued items, items soiled
with abrasive, acidic or base
chemicals.
•Temperature-sensitive plastics,
copper or tincoated containers.
•Aluminium and silver objects.
•Some delicate glasses, ornamental
printed porcelains; some crystal
items, adhered cutlery, lead crystal
glasses, cutting boards, synthetic
fibred items.
•Absorbent items such as sponges or
kitchen rugs.
IMPORTANT: In future, purchase
dishwasher-proof kitchenware.
Important Note for Test Laboratories
For detailed information required for tests
according to EN normatives and a softcopy
of the manual, please send the model name
and serial number to the following address:
[email protected]
EN - 18

EN - 19
6 PROGRAMME TABLE
P1 P2 P3 P4 P5
Programme
Name: Quick 30’
Eco Super 50’ Intensive 65°C Prewash
Type of Soil:
Standard
program for
normally
soiled daily
use dishes
with reduced
energy
and water
consumptions.
Suitable for
normally
soiled daily
dishes
with faster
program.
Suitable for
heavily soiled
dishes.
Level of Soil: Light Medium Medium Light
Heavy
Amount of
Detergent:
A: 25 cm3
A A A A -
Program
Duration
(h:min)
00:3003:25 00:5001:57 00:15
Electiricity
consumption
(kWh/cycle)
0.7400.937 1.1001.700 0.020
Water
consumption
(l/cycle)
12.4
12.0 12.0
17.2 4.5
•The program duration may change according to the amount of dishes, the water temperature, the
ambient temperature and selected additional functions.
•Values given for programmes other than the eco programme are indicative only.
•Eco programme is suitable to clean normally soiled tableware, that for this use, it is the most efficient
programme in terms of its combined energy and water consumption, and that it is used to assess
compliance with the EU ecodesign legislation.
•Washing tableware in a household dishwasher usually consumes less energy and water in the use
phase than hand dishwashing when the household dishwasher is used according to the manufacturer’s
instructions.
•Only use powder detergent for short programs.
•Short programs do not include drying.
•To assist drying, we recommend slightly opening the door after a cycle is complete.
•You can access the product database where the model information is stored by reading the QR code on
the energy label.
NOTE: According to regulations 1016/2010 and 1059/2010, Eco program energy
consumption values may differ. This table is in line with regulations 2019/2022 and
2017/2022
Programme
Symbol
Suitable
for lightly
soiled
dishes and
quick wash.
Suitable
to rinse
dishes
that you
plan to
wash
later.

EN - 20
7 THE CONTROL PANEL
1. On/O󰀨 button
2. Programme Selection Button
i. Programme LED's
3. Half Load Button
ii. Half Load Led
4. Delay Button
iii. Delay LED's
iv. Salt Indicator
v. Rinse Aid Indicator
vi. End of Programme Indicator
1. On/O󰀨 Button
Switch the machine on by pressing On/O󰀨
button. When machine is on, the End Of
Programme Indicator (vi) will illuminate.
2. Programme Selection Button
Select a suitable programme for your
dishes by pressing Programme
Selection button. The Programme Led (i)
corresponding to the selected programme
will illuminate and the End Of Programme
Indicator (vi) will switch o󰀨. The programme
will start automatically when the door is
closed.
3. Half Load Button
Press the Half Load button to reduce the
duration of the selected programme, and
therefore decrease your energy and water
consumption. When Half Load option is
selected, Half Load led (ii) will illuminate.
4. Delay Button
Press the Delay button to delay the start
time of a programme for 3, 6 or 9 hours.
Pressing once will delay the start time for 3
hours, pressing twice for 6 hours, and three
times for 9 hours. Press the Delay Timer
button to change or cancel the delayed start
time. The Delay led (iii) corresponding to
the remaining delay duration (3h, 6h, 9h)
will be on. If you switch o󰀨 the machine
after activating the delay time, the delayed
time is cancelled.
NOTE: If you decide not to start the
selected programme, please see the
"Changing a Programme" and "Cancelling a
Programme" sections.
NOTE: When there is insu󰀩cient
softening salt, the Salt Lack Warning
Indicator (iv) will illuminate to indicate the
salt chamber needs lling.
NOTE: When there is insu󰀩cient rinse
aid, the Rinse Aid Lack Warning Indicator
(v) will illuminate to indicate the rinse aid
chamber needs filling.
7.1 Changing a Programme
Follow the steps below to change a
programme while in operation.
NOTE: Open the door slightly at rst to
stop a programme before it is complete in
order to avoid water spillage.
Open the door and select a new
programme using the Programme
Selection button.
After closing the door, the new
programme will resume the
course of the old programme.