Moog Videolarm O124TL Instruction sheet

1/4" flat washer
split lockwasher
hex nut
long metal bracket
short metal bracket
1/4"-20 bolt
1/4" flat washer
split lockwasher
carriage
5/16" flat washer
split lockwasher
1/4" flat washer
1/4"-20 bolt
1/4"-20 bolt
Figure 1
Figure 2
Contents Include:
(1) Tinted Acrylic Dome
(1) Black, Opaque Inner Liner
e, 2 x 2 CeilingTile
(1) FM2 Camera Bracket Packet
(1) 1/4-20 x 3/4" carriage bolt
(3) 1/4" at washer
(3) 1/4" split lockwasher
(1) 1/4-20 hex nut
(1) FM2 bracket (long arm)
(1) 5/16" washer
(1) FM2 bracket (short arm)
(1) 1/4-20 x 1/2" hex bolt
(1) 6-32 hex nut
(1 ) 6-32 x 1/2 Phillips ss
(1) #6 star lock washer
1. Remove contents from the box.
2. Assemble the FM2 camera bracket. Align the long slot on
the long bracket with the long slot on the short bracket.
Using a carriage bolt, 5/16" washer, 1/4" at washer, split
lockwasher, and hex nut, attach bracket arms together
loosely (Figure 1).
3. Mount the FM2 bracket to one of the three holes located
in the center of the 2 x 2 black housing tile..
4. Remove the existing ceiling tile from the desired location.
NOTE: In some cases units may be pre-assembled.
5. Insert the loose end of the saftey cord on the dome
through the middle hole on the edge of the housing
opening (Figure 2).
6. Align the eyelet on the cord with the hole located on the
inside of the housing tile opening.
7. Insert the 6-32 x 1/2 round Phillips head screw through
the hole and eyelet. Place the star lockwasher and 6-32
hex nut on the screw and tighten.
8. Fit the 2 x 2 housing tile in the desired location. The
housing tile will rest on the ceiling grid. (Be sure the grid
is adequately supported).
9. Feed the wire through the conduit hole in the top of the
housing tile.
10. Secure the camera to the swivel on the FM2 bracket.
11. Adjust the camera to the desired position, tighten all
connections and complete the wiring of the camera.
12. Place the black opaque liner into the dome and rotate the
black retaining tabs on the dome ange so that they hold
the liner in place.
13. Rotate the liner so that the hole is in the correct position
for the camera lens.
14. Place the dome so the the swivel latches into the two
holes on the housing tile.Snap the latch closed.
2525 Park Central Blvd. • Decatur, Ga 30035 • [phone] • 800-554-1124 U.S. & Canada • www.videolarm.com • Fax [phone]
Figure 1
Figure 2
Figure 3
REVISION DATE: 02-02-2009
81-IN5161 O124TL / O125D
PRODUCT INSTRUCTIONS
© 2009, Videolarm, Inc. All Rights Reserved

!
CAUTION
RISK OF
ELECTRIC SHOCK!
CAUTION: TO REDUCE THE RISK OF
ELECTRICAL SHOCK, DO NOT EXPOSE
COMPONENTS TO WATER OR MOISTURE.
SAFETY PRECAUTIONSIMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instructions should be read
before the unit is operated.
2. Retain Instructions -The safetyandoperating instructionsshould be retained
for future reference.
3. Heed Warnings - All warnings on the unit and in the operating instructions
should be adhered to.
4. Follow Instructions - All operating & user instructions should be followed.
5. Electrical Connections - Only a qualified electrician should make electrical
connections.
6. Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7. Cable Runs - All cable runs must be within permissible distance.
8. Mounting - This unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of the unit. Accordingly:
a. Installation should be made by a qualified installer.
b. Installation should be in compliance with local codes.
c. Care should be exercised to select suitable hardware to install the unit,
taking into account both the composition of the mounting surface and
the weight of the unit. Be sure to periodically examine the unit and the
supporting structure to make sure that the integrity of the installation
is intact. Failure to comply with the foregoing could result in the unit
separating from the support structure and falling,with resultant damages
or injury to anyone or anything struck by the falling unit.
UNPACKING
Unpackcarefully. Electroniccomponentscanbedamaged if improperlyhandled
or dropped. If an item appears to have been damaged in shipment,replace it
properly in its carton and notify the shipper. Be sure to save:
1. The shipping carton and packaging material. They are the safest material in
which to make future shipments of the equipment.
2. These Installation and Operating Instructions.
!
The lightning flash with an arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of non-insulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intendedtoalerttheusertopresenceofimportantoperating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
24 HOUR TECHNICAL SUPPORT
1-800-554-1124
SERVICE
If the unit ever needs repair service,customer should contact Videolarm
(1-800-554-1124) for return authorization & shipping instructions.
TECHNICAL SUPPORT
Videolarm has set-up a 24 hour technical support line for their customers.
LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS
VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship,as follows:
PRODUCT CATEGORY PARTS LABOR
All Enclosures and Electronics Five (5) Years Five (5) Years
Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan
Poles/PoleEvators Three (3) Years Three (3) Years
Warrior/Q-View/I.R. Illuminators Five (5) Years Five (5) Years
Controllers Five (5) Years Five (5) Years
Power Supplies Five (5) Years Five (5) Years
Accessory Brackets Five (5) Years Five (5) Years
During the labor warranty period, to repair the Product,Purchaser will either return the defective product,freight prepaid, or deliver it to Videolarm Inc. Decatur GA.
The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with a RMA # (Return Materials
Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support Team at 800.554.1124,extension 101.
Videolarm will return the repaired Product freight prepaid to Purchaser.Videolarm is not obligated to provide Purchaser with a substitute unit during the warranty
period or at any time.After the applicable warranty period, Purchaser must pay all labor and/or parts charges.
The limited warranty stated in these product instructions is subject to all of the following terms and conditions:
1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship,then written notice
with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the warranty period.
If after investigation Videolarm determines that the reported problem was not covered by the warranty, Purchaser shall pay Videolarm for the cost of investigating
the problem at its then prevailing per incident billable rate.No repair or replacement of any Product or part thereof shall extend the warranty period as to the entire
Product.The specific warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part or the
remaining period of the Product parts warranty, whichever is greater.
2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair
any Product found to be defective within the warranty period and to supply, at no extra charge,new or rebuilt replacements for defective parts.
3. EXCEPTIONS TO LIMITED WARRANTY: Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during
the warranty period which is subjected to any of the following: abuse, improper use: negligence, accident, lightning damage or other acts of God (i.e., hurricanes,
earthquakes), modification, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance
procedures recommended by the International Security Industry Organization,written in product instructions, or recommended in the service manual for the Product.
Furthermore,Videolarm shall have no liability where a schedule is specified for regular replacement or maintenance or cleaning of certain parts (based on usage)
and the end-user has failed to follow such schedule; attempted repair by non-qualified personnel; operation of the Product outside of the published environmental
and electrical parameters, or if such Product’s original identification (trademark,serial number) markings have been defaced,altered,or removed. Videolarm
excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser.
All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where
expressly provided otherwise in any documentation or license agreement furnished with the Product.
4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES,VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES,EXPRESS OR IMPLIED,
INCLUDING,BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH REGARD TO ANY CLAIM
OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE.VIDEOLARM HEREBY DISCLAIMS
ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-VIDEOLARM PRODUCTS OR NON-VIDEOLARM RECOMMENDED PRODUCTS
PURCHASER CHOOSES TO CONNECT TO PRODUCT.
LIMITATION OF LIABILITY THE LIABILITY OF VIDEOLARM,IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER,
REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH
SUCH CLAIM IS MADE. IN NO EVENT SHALL VIDEOLARM BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING,BUT NOT
LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
/ tour operation / tour operation
**6 months if used in autoscan
/ tour operation **6 months if used in autoscan / tour operation
SView Series Five (5) Years Five (5) Years