Moog Videolarm OH206T Instruction sheet

!
Specification Catalog
Number Section
INSTRUCTIONS 5178 1b
MODEL: Indoor Ceiling Housings
OH201TL/CL; OH161TL/CL; OH121TL/CL,
OH206T/C, OH166T/C, OH126T/C
PRODUCT INSTRUCTIONS
STANDARD INSTALLATION PROCEDURE
INCLUDES MODELS: OH201TL/CL; OH161TL/CL;
OH121TL/CL; OH206T/C, OH166T/C,
OH126T/C
Use Only Class 2 Power Supply
2525 Park Central Blvd. • Decatur, Ga 30035 • [phone] • 800-554-1124 U.S. & Canada • Fax [phone] • www.videolarm.com
MODEL OH201TL, CL/OH161TL, CL/OH121TL, CL
Housing Contents:
(1) Tinted /clear dome
(2) Support channels
(1) Black opaque liner
(1) FM2 camera bracket assembly
(1) Black dust cover
1. Remove contents from the box.
2. Remove the ceiling tile in the desired location.
3. Place the dome so that it rests on the ceiling grid.
NOTE: Be sure that the grid is adequately supported.)
4. Place the black opaque liner in the dome and rotate it to the
desired viewing postion.
5. Only one viewing slot is provided in the liner. If more than one
camera is being mounted, additional holes can be cut in the
liner using a hole saw or utility knife. Be sure to orient each
viewing hole correctly.
6. Assemble the FM2 camera bracket. Align the long slots of the
bracket arms. Using a carriage bolt, 5/16" washer, 1/4"
washer, lockwasher and hex nut, attach the bracket arms
together loosely (Figure 1, next page).
7. Assemble the Support Channels. Slide the smaller channel
through the slot on the larger one (Figure 2, next page). BE
CAREFUL WHEN HANDLING SUPPORT CHANNELS,
EDGES MAY BE SHARP.
8. Use the 1/4 x 20 bolt supplied to connect the FM2 to the cen-
ter hole on the support channel assembly.
NOTE: For added flexibility, the camera can be mounted on
either the short or long side of the bracket arm.
9. Securing tabs are provided to hold the bracket in the liner.
Bend the corresponding tab with a screwdriver (Figure 2, next
page).
10. Connect the camera to the FM2 bracket and place the
assembly in the dome so that the edges of the bracket will rest
on the flange of the dome (Figure 3, next page).
11. Tighten all connections and complete wiring of the camera.
12. Place the black dust cover over the top of the dome, so that
the dust cover is sitting on the support channels.
MODEL OH206T/OH166T/OH126T
Housing Contents:
(1) Tinted /clear dome
(2) Support channels
(1) FM2 camera bracket assembly
1. Remove contents from the box.
2. Remove the ceiling tile in the desired location.
3. Place the dome so that it rests on the ceiling grid.
NOTE: Be sure that the grid is adequately supported.)
4. Assemble the FM2 camera bracket. Align the long slots of the
bracket arms. Using a carriage bolt, 5/16" washer, 1/4"
washer, lockwasher and hex nut, attach the bracket arms
together loosely (Figure 1, next page).
5. Assemble the Support Channels. Slide the smaller channel
through the slot on the larger one (Figure 2, next page). BE
CAREFUL WHEN HANDLING SUPPORT CHANNELS,
EDGES MAY BE SHARP.
6. Use the 1/4 x 20 bolt supplied to connect the FM2 to the cen-
ter hole on the support channel assembly.
NOTE: For added flexibility, the camera can be mounted on
either the short or long side of the bracket arm.
7. Securing tabs are provided to hold the bracket in the dome.
Bend the corresponding tab with a screwdriver (Figure 2).
8. Connect the camera to the FM2 bracket and place the
assembly in the dome so that the edges of the bracket will rest
on the flange of the dome (Figure 3, next page).
9. Tighten all connections and complete wiring of the camera.
MODEL OH202D/162D/122D
Contents include:
one black acrylic dome
1. Remove contents from the box.
2. Remove the ceiling tile in the desired location.
3. Place the dome so that it rests on the ceiling grid.
REVISION DATE: August 7, 2003
DOME CARE
Please use the following precautions to maintain the dome’s
perfect optical properties:
• Always handle the dome from the outside of its circular flange.
• If dust or other contaminants accumulate on the dome, they
should be removed with clean air pressure.
• If compressed air is not available the dome can be cleaned
with any non-abrasive cleaning cloth, and a cleaning agent
that is safe for use on acrylic.

- 2 -
Figure 1 Figure 2
Figure 3
Figure 4
PA RT # QTY. DESCRIPTION
1 90-BTCA01 2 1/4-20 x 3/4" Zinc Carriage
2 90-VL696 1 4 in 1 Camera Bracket
3 92-WSSL01 2 1/4 Split Lockwasher 18-8 SS
4 91-NTHH33 2 1/4-20 Wing Nut
5 92-WSLF01 1 1/4 SAE Flat Washer 18-9 SS
6 92-WSFL05 1 5/16 Flat Washer SS
7 30-VL732 1 0-1 Multiple Camera Bracket
8 96-RSORNG 1 -009 O-Ring
9 90-BTW04 1 1/4-20 x 1/2 Wing Screw
Black Opaque Dust Cover
Support Channels
FM2 Camera Bracket
Pre-Cut Liner (OH121/161/201)
Acrylic Dome
Ceiling Grid (not supplied)
1
2
3
4
5
678
9

!
Caution
Risk of
ElECtRiC shoCk!
Caution: to REDuCE thE Risk of
ElECtRiCal shoCk, Do not EXPosE
CoMPonEnts to WatER oR MoistuRE.
safEtY PRECautionsiMPoRtant safEGuaRDs
1. Read Instructions - All the safety and operating instructions should be read
before the unit is operated.
2. Retain Instructions -The safetyandoperating instructions shouldbe retained
for future reference.
3. Heed Warnings - All warnings on the unit and in the operating instructions
should be adhered to.
4. Follow Instructions - All operating & user instructions should be followed.
5. Electrical Connections - Only a qualified electrician should make electrical
connections.
6. Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7. Cable Runs - All cable runs must be within permissible distance.
8. Mounting - This unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of the unit. Accordingly:
a. Installation should be made by a qualified installer.
b. Installation should be in compliance with local codes.
c. Care should be exercised to select suitable hardware to install the unit,
taking into account both the composition of the mounting surface and
the weight of the unit. Be sure to periodically examine the unit and the
supporting structure to make sure that the integrity of the installation
is intact. Failure to comply with the foregoing could result in the unit
separating from the support structure and falling,with resultant damages
or injury to anyone or anything struck by the falling unit.
unPaCkinG
Unpackcarefully. Electronic components can bedamagedifimproperlyhandled
or dropped. If an item appears to have been damaged in shipment, replace it
properly in its carton and notify the shipper. Be sure to save:
1. The shipping carton and packaging material. They are the safest material in
which to make future shipments of the equipment.
2. These Installation and Operating Instructions.
!
The lightning flash with an arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of non-insulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intendedtoalerttheusertopresenceofimportantoperating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
24 houR tEChniCal suPPoRt
1-800-554-1124
sERViCE
If the unit ever needs repair service,customer should contact Videolarm
(1-800-554-1124) for return authorization & shipping instructions.
tEChniCal suPPoRt
Videolarm has set-up a 24 hour technical support line for their customers.
LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS
VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship, as follows:
PRODUCT CATEGORY PARTS LABOR
All Enclosures and Electronics Three (3) Years Three (3) Years
Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan
Poles/PoleEvators Three (3) Years Three (3) Years
Warrior/Q-View/I.R.Illuminators Five (5) Years Five (5) Years
Controllers Three (3) Years Three (3) Years
Power Supplies Three (3) Years Three (3) Years
Accessory Brackets Three (3) Years Three (3) Years
During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Videolarm Inc. Decatur GA.
The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with a RMA # (Return Materials
Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support Team at 800.554.1124, extension 101.
Videolarm will return the repaired Product freight prepaid to Purchaser.Videolarm is not obligated to provide Purchaser with a substitute unit during the warranty
period or at any time.After the applicable warranty period, Purchaser must pay all labor and/or parts charges.
The limited warranty stated in these product instructions is subject to all of the following terms and conditions:
1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice
with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the warranty period.
If after investigation Videolarm determines that the reported problem was not covered by the warranty, Purchaser shall pay Videolarm for the cost of investigating
the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period as to the entire
Product.The specific warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part or the
remaining period of the Product parts warranty, whichever is greater.
2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair
any Product found to be defective within the warranty period and to supply, at no extra charge,new or rebuilt replacements for defective parts.
3. EXCEPTIONS TO LIMITED WARRANTY: Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during
the warranty period which is subjected to any of the following: abuse, improper use: negligence, accident, lightning damage or other acts of God (i.e., hurricanes,
earthquakes), modification, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance
procedures recommended by the International Security Industry Organization,written in product instructions,or recommended in the service manual for the Product.
Furthermore,Videolarm shall have no liability where a schedule is specified for regular replacement or maintenance or cleaning of certain parts (based on usage)
and the end-user has failed to follow such schedule; attempted repair by non-qualified personnel; operation of the Product outside of the published environmental
and electrical parameters, or if such Product’s original identification (trademark,serial number) markings have been defaced,altered, or removed. Videolarm
excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser.
All software and accompanying documentation furnished with, or as part of the Product is furnished“AS IS”(i.e., without any warranty of any kind),except where
expressly provided otherwise in any documentation or license agreement furnished with the Product.
4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES,VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH REGARD TO ANY CLAIM
OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. VIDEOLARM HEREBY DISCLAIMS
ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-VIDEOLARM PRODUCTS OR NON-VIDEOLARM RECOMMENDED PRODUCTS
PURCHASER CHOOSES TO CONNECT TO PRODUCT.
LIMITATION OF LIABILITY THE LIABILITY OF VIDEOLARM,IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER,
REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH
SUCH CLAIM IS MADE. IN NO EVENT SHALL VIDEOLARM BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL,OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT
LIMITED TO,COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.