Moog Videolarm JK-PHO Instruction sheet

!
!
Manufactured by:
Before attempting to connect or operate this product, please read these instructions completely.
81-IN4500
6/17/02
for
IN-4500
MODELS: Outdoor Dome Housings
JK-PHO, JK-PHI
ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY):
Power 24VAC, Class 2 Only
26 watts at 24 VAC (accessories)
Heater: 25 watts
Blower: .84 watts
Input Connectors (outdoor units):
BNC
(2) screw-down connectors
GENERAL INSTRUCTIONS:
Tools Required: .100" Flat Head Screwdriver
Phillips Head Screwdriver
1. Carefully remove the housing from the packaging material.
Check to be sure all parts are present.
2. This unit includes a 1 1/2" NPT housing coupling that can be
used with a standard 1 1/2" NPT pipe. The unit can be
used with other brackets designed with 1 1/2" male pipe
threads, such as the Toshiba's JK-WM and JK-PJM wall
mount brackets.
3. Attach the housing coupling to the bracket or pendant pipe
(Figure 1).
NOTE: Pipe threads should be clean and rust free. Use a
sealer (such as Teflon™ tape or silicone sealer) on the
threads.
Figure 1
Add thread
sealing tape
Be sure the bracket is properly and securely mounted
to a supporting structure capable of rigidly holding the
weight of the entire unit.
INSTALLING QUICK RELEASE BRACKET AND PAN/TILT
CAMERA ASSEMBLY
NOTE: These installations should be completed before
mounting the housing.
1. Open the housing by loosening the (3) captive screws located
on the housing ring next to the lower clear dome. Be careful
not to back these all the way out. Twist the dome slightly in a
counterclockwise motion to remove (Figure 2).
Figure 2
Loosen screws only,
do not remove
Remove dome by
twisting counter-
clockwise
2. Install the pan/tilt unit quick- release bracket using the three
6-32 Phillips head screws provided (Figure 3). Screw down
only about halfway.
PRODUCT INSTRUCTIONS
Figure 2
Mounting
screws
3. Make wiring connects from the housing to the Pan/Tilt base
(Figure 3). Use the Color Code Chart B on the next page for
correct connections.
Figure 3
Orange
Red
Blue Violet Gray White

- 2 -
A. Wiring Color Code
Power and Control Inputs
(Outside of housing)
1 Camera Power (24 VAC) Red
2 Camera Power (24 VAC) Orange
3 Accessory Power (24 VAC) Yellow
4 Accessory Power (24 VAC) Green
1 RS-485RXA Blue
2 RS-485RXB Violet
3 RS-485TXA Gray
4 RS-485TXB White
1 Camera Power (24 VAC) Red
2 Camera Power (24 VAC) Orange
3 RS-485RXA Blue
4 RS-485RXB Violet
5 RS-485TXA Gray
6 RS-485TXB White
POWER
CONTROL
POWER AND CONTROL LEADS
B. Power and Control Outputs
(Inside of housing)
4. Connect the Pan/Tilt base to the quick-release bracket by sliding
the slots on the top of the base over the screws on the quick-
release bracket. Tighten the screws to secure the base to the
bracket (Figure 4).
Figure 4
Place slots
over screws
in quick-
release
bracket
MOUNTING THE HOUSING
1. Mount the housing assembly to the mounting bracket and
housing coupling. A safety cable is included with the housing to
temporarily hold it while making wiring connections. Loop the
safety cable over one of the set screws on the housing coupling
2. Make the appropriate connections using the (2) screw-down
connectors supplied. Refer to Chart A as a guide.
3. Undo the safety cable and twist the housing onto the housing
coupling. Secure all (3) set screws provided on the housing
coupling (Figure 7).
5. Attach the safety cable on the bottom of the camera onto the slot
on the Pan/Tilt base (Figure 5).
Figure 5
6. Attach the Six Position Pan/Tilt Connector from the camera to the
Pan/Tilt base (Figure 6). Connect the dome camera to the Pan/Tilt
base by aligning the notch on the Pan/Tilt base with the arrow on
the camera, and turning the camera clockwise until it locks.
Figure 6
Six Position
Pan/Tilt
Connector
7. Clean the inside of the dome with the text-wipe provided. Reat-
tach the housing dome and secure the (3) captive screws. DO
NOT OVERTIGHTEN THE SCREWS. Tighten only to the point at
which the gap between the ring and the housing top closes.
Figure 6
4. Clean the outside of the dome with the text wipe provided.
Twist and
Secure
WIRING FOR INDOOR UNITS
1. Run incoming wiring into the top of the housing and through the
hole in the center of the quick release bracket. (Figure 7).
2. Attach the housing to the pendant coupling.
3. Connect the wiring to the Pan/Tilt base per Toshiba's instructions.
Figure 7
Center
hole

- 3 -
16
15
7
13
12
11
10
9
8
7
6
5
4
3
2
21
22
18
28
26
27
20
19
17
EXPLODED VIEWS OF HOUSING
Item No. Description Part No. Qty
2 Housing Top 30-VL1697 1
3 Dome Support Ring 30-VL1695 1
4 25W, 24VAC w/Leads 72-HT1752 1
5 Clear Dome 20-DCFD8 1
n/s Tinted Dome 20-DTFD8 1
n/s 9.25" O-ring 96-RSORG11 2
6 Plastic Ring Plugs 30-VL1696 6
7 PCB 76-FPD8PB 1
8 Upper Housing Bracket 30-VL1744 1
9 Housing Gasket 96-PSGK05 3
10 Housing Fan 71-VLBL03 1
11 Adapter Bracket (In Housing Packet) 40-PKFD8 1
12 1/4 x 20 x .75" HH Bolts 90-BTHH27 4
12 1/4 Split Lock Washer 92-WSSL01 4
12 1/4 Flat Washer 92-WSFL01 4
13 10 x 32 x .75 Phil PH SS 90-BTRP28 3
15 Captive Screw 30-VL1749 3
n/s Captive Screw Spring 92-SPR01 3
n/s Captive Screw Retainer 94-FSRT04 3
16 Main Housing Bracket 30-VL1742 1
n/s Housing Ring 1" Lanyard Spring 92-SPR02 1
n/s Lanyard Spring Screws 90-BTPEM01 2
n/s Power/Control/Video Input Cable 40-CAFD802 1
17 1/4 x 20 FH SS Bolt 90-BTSR01 1
18 Housing Pendent Bracket 30-VL926 1
19 1/4 Split Lock Washer 92-WSSL01 1
20 1/4 Flat Washer 92-WSFL01 1
21 Housing Gasket 96-PSGK05 1
22 1/4 x 20 x 1/2" Set Screw 90-BTSS05 2
26 1 1/2" Housing Coupling 30-VL917 1
27 Upper Housing Gasket 96-PSGK04 1
28 1/4 x 20 x .375" HH Bolts 90-BTHH39 2
n/s 1/4 Flat Washer 92-WSFL01 2
n/s 1/4 Split Lock Washer 92-WSSL01 2
Parts List
1. Housing
2. Housing Coupling
3. Housing Packet
a. (2) Mates for screw down connectors (not supplied with
indoor units)
b. (3) 6 x 32 x 3/8" Mounting screws with star washers
c. (2) 1/4” Flat washers
d. (2) 1/4" Split Lock washers
e. Instruction Manual

- 4 -
SAFETY PRECAUTIONSIMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instructions
should be read before the unit is operated.
2. Retain Instructions - The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the unit and in the operating
instructions should be adhered to.
4. Follow Instructions - All operating and user instructions should
be followed.
5. Electrical Connections - Only a qualified electrician should
make electrical connections.
6. Attachments - Do not use attachments not recommended
by the product manufacturer as they may cause hazards.
7. Cable Runs - All cable runs must be within permissible
distance.
8. Mounting - This unit must be properly and securely mounted
to a supporting structure capable of sustaining the weight
of the unit. Accordingly:
a. The installation should be made by a qualified installer.
b. The installation should be in compliance with local
codes.
c. Care should be exercised to select suitable hardware to
install the unit, taking into account both the composition
of the mounting surface and the weight of the unit. Be
sure to periodically examine the unit and the supporting
structure to make sure that the integrity of the installation is
intact. Failure to comply with the foregoing could result in
the unit separating from the support structure and falling,
with resultant damages or injury to anyone or anything
struck by the falling unit.
ONE-YEAR LIMITED WARRANTY
Videolarm, Incorporated warrants that products sold
hereunder shall be fit for the ordinary purpose for which
said products are intended and shall be free from defects
in material and workmanship for a period of one year from
date of sale to buyer. Note that all electrical components
will be warranted for a period of 1 year from date of sale
to buyer. Videolarm makes no other warranty of any kind
with respect to this product, whether expressed or implied,
including, without limitation, the implied warranty of fitness
for a particular purpose.
In the event of a breach of the above warranty, Videolarm
shall, at its option, repair or replace said product. This is
Videolarm's sole obligation under this warranty. In no event
shall Videolarm be liable for any incidental or consequential
damages, as defined in section 2-715 of the Uniform
Commercial Code by a breach of this warranty.
Videolarm shall repair or replace defective products upon
shipment of products prepaid to Videolarm, Inc., 2525 Park
Central Blvd., Decatur, GA 30035.
Repairs made necessary by reason of accident, misuse or
normal wear shall be charged at Videolarm's standard rate.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
UNPACKING
Unpack carefully. Electronic components can be
damaged if improperly handled or dropped. If an item
appears to have been damaged in shipment, replace it
properly in its carton and notify the shipper.
Be sure to save:
1. The shipping carton and packaging material. They are
the safest material in which to make future shipments of
the equipment.
2. These Installation and Operating Instructions.
SERVICE
If the unit ever needs repair service, the customer should
contact Videolarm (1-800-554-1124) for authorization to
return
and shipping instructions.
TECHNICAL SUPPORT
If technical support is needed, Videolarm has set-up a 24
hour technical support line for their customers.
1-800-554-1124
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO
NOT OPEN COVERS. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with an arrowhead symbol,
within an equilateral triangle, is intended
to alert the user to the presence of non-
insulated "dangerous voltage" within the
product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock
to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to presence
of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
24 HOUR TECHNICAL SUPPORT
CAUTION
RISK OF
ELECTRIC SHOCK!
!
!