MORDOMUS Meteo-1706 User manual

Meteo – Weather Sensor Hardware: V4.0
Firmware: V4.4
1. GENERAL FEA URES :
Reading points: 4, temperature, light, wind intensity and rain
detection;
Command: Via MD BUS;
Applications: Weather information current;
Installation: Outside the building
2. GENERAL SPECIFICA IONS :
Voltage: 12VDC;
Consumption: 150mA @ 12VDC;
Storage emperature: -10ºC to 60ºC;
emperature Operating: -60ºC to 60ºC;
Readings:
Temperature: -60ºC to 60ºC;
Brightness: 10 levels;
Wind: 10 levels;
Rain: true/false;
Physical Specifications:
Box Plastic, self-extinguishing UL-94 V0;
Level of Protection: IP54, for outdoor use
Directives:
-Electromagnetic Compatibility Directive / EMC
Directive 2004/108/EC
3. COMPA IBILI Y :
PCCWd Compatibility: Firmware 3 4 or higher version V3 2
or V3 31 with BUS Adapter;
Mordomus Software Compatibility: Mordomus Software
v2015 2 or higher;
4. SECURI Y :
Before making any connections, please read these
instructions
5. INS ALLA ION:
1 Must handle carefully the parts of the module and
ensure ITS correct assembly;
2 It is important to establish the place of installation so
METEO IS exposed to the elements so then can be
measure
Note that if the ME EO is installed to direct sunlight will
measure temperatures according to the exposure, and
different temperatures may be measured in the shade.
3 METEO should be inclined 45 ° relative to the
horizon, so that the rain water runs down, as the Fig
4;
4 Do not paint or polish METEO sensitive surface;
5 The accumulation of dirt on the rain sensor limits its
sensitivity, which must be cleaned twice a year with
a damp cloth or when it shows signs of dirt or
incorrect readings
If the chosen location for METEO has a difficult access and/or
remote to the Mordomus console, it is advisable to carry out
the address through a previous temporary connection with the
frame and the console
After this previous assemble the METEO in its place
6. CONNEC IONS:
Thickness of conductors:
Circuit Bus:
CAT6 Cable F/UTP shielded, twisted;
Power Circuit:
CAT6 Cable F/UTP shielded, twisted;
In case of installation with BUS ADAP ER, ME EO
should be at the end of RX Bus chain.
Connect the Bus:
To connect the BUS should use a twisted pair cable CAT6
For example: Green for A and Green/White to B The shield
should be connected to GND
Connect the 12VDC power:
It is recommend the use of Mean-Well power supplies, DR60-
12 and DR30-12
Manual: Meteo-1706-EN www mordomus com Page 1/2

Meteo – Weather Sensor Hardware: V4.0
Firmware: V4.4
In case the module is the last position on the bus, jumpers
should be placed according to Fig 1 A) to close the BUS
chain In the case of bus lenght very long you may need only
put the jumper Term In other situations should remain as in
Fig 1 B)
Fig 2:
Fig. 4:
7. ADDRESSING AND CONFIGURA ION :
After connected and powered, perform the following steps:
1 Open "Register modules" in the Mordomus software;
2 Press address (Addressing) inside the module The
Green LED will blink slowly and the red LED will
pulse once
Note that after three minutes without having assigned a
new address, the module automatically returns to normal
mode
3 Set the desired address in the window now displayed
on Software Mordomus
8. FUNC IONING:
Led Code:
D5 Green LED ON: Module powered;
D5 Green LED blinking briefly: Module receiving data;
D5 Green LED blinking continuously: Module awaiting
address;
D4 Red LED blinking: module sending data
Manual: Meteo-1706-EN www mordomus com Page 2/2