Morrison Bros. co. 419EG Installation and operating instructions
1
Morrison Bros. Co. ‑ Dubuque, IA ‑ 800‑553‑4840
419EG‑0203 PP
rev. 3-30-2022
!
!
!
Failure to follow any or all of the warnings may render the part nonfunctional and could result in a
hazardous product spill, which may result in property damage, environmental contamination, re,
explosion, injury or death.
Installation
WARNINGS
•Fire Hazard—Death or serious injury could result from spilled liquids.
• Any modication to this product other than stated in these installation instructions will void the product
warranty.
• Install in accordance with all applicable local, state, and federal laws.
• For your safety, it is important to follow local, state, federal and/or OSHA rules that apply to working inside,
above, or around the storage tank and piping area. Use all personal protective equipment required for working
in the specic environment.
• Tanks could be under pressure. Vapors could be expelled from tank vents, piping, valves or ttings while
performing installation. Vapors could catch re or cause an explosion. Avoid sparks, open ame, or hot tools
when working on tanks.
• Fill points should be labeled to identify product being transferred, according to all applicable codes.
• In the event of malfunction, contact Morrison Bros. Co. customer service.
Steps
1. Ensure Extender is being used on Morrison 2” drop tube.
2. Locate Extender Tool (see Figure 1).
3. Make sure the ends of the drop tube sections are cut square.
4. Locate installation template sticker and follow steps 1-8 listed on template (see Figure 2). When applying
label ensure both cut ends are butted together inline and square (see Figure 3). The QR code on template
includes a supplemental installation video if needed.
5. Before installing in the tank opening, check the drop tubes and connection for any bends or internal
blockages. If any are noticed, you may need to replace the drop tubes or remove blockage before proceeding.
Maintenance
This product should be maintained according to local codes.
WARNINGS
•Fire Hazard – Death or serious injury could result from spilled liquids.
• You must be trained to maintain this product. Stop now if you have not been trained.
• For your safety, it is important to follow local, state, federal and/or OSHA rules that apply to working inside,
above, or around the storage tank and piping area. Use all personal protective equipment required for working
in the specic environment.
• Tanks could be under pressure. Vapors could be expelled from tank vents, piping, valves or ttings while
performing maintenance. Vapors could catch re or cause an explosion. Avoid sparks, open ame, or hot tools
when working on tanks and tank accessories.
419EG Drop Tube Extender for 2” Drop Tube
for Gauging Applications
Installation & Maintenance Instructions
2
Morrison Bros. Co. ‑ Dubuque, IA ‑ 800‑553‑4840
419EG‑0203 PP
rev. 3-30-2022
Figure 1
5Clamp the 419EGT installation tool onto template, aligning top edge of tool with this line.
Ensure vertical line A is visible through notch in tool.
Turn each threaded forming screw until
it bottoms out, dimpling the sleeve. Then loosen
screws and remove clamp.
6
7Clamp the 419EGT installation tool onto template, aligning top edge of tool with this line.
Ensure vertical line B is visible through notch in tool.
Turn each threaded forming screw until
it bottoms out, dimpling the sleeve. Then loosen
screws and remove clamp.
8
Scan QR code for
installation video.
Peel backing off sticker.
1
Align top and bottom tube ends
to this line.
Roll sticker onto tubes.
2
START
HERE
Drill .25″ diameter holes
(Center punch and pilot holes
recommended)
3
ASlide 419EG sleeve onto template, positioned between dashed lines.
4
B
(then follow the numbered steps)
FOR ILLUSTRATION ONLY
Figure 2
Figure 3
