mothercare adjust with me highchair User manual

‘adjust with me’ highchair
user guide
IMPORTANT! KEEP FOR FUTURE REFERENCE

introduction
The Mothercare Adjustable High Chair has been designed to comfortably seat
your baby from the time they can sit up by themselves (around 6 months) well into
their teenage years.
This product has been manufactured from wood and as such will naturally darken
with age.
This high chair conforms to BSEN14988: 2006
1
important notes
As all children grow differently, the height of this product can be adjusted to suit
your child’s individual needs. Before assembling the high chair please take a few
moments to select the best seat and foot rest positions for your child. The below
guide has been written to help you select the best positions for the seat and foot
rest for your child’s growth stage.
stage 1
6-9 months = Seat in slot 1, Footrest in slot 4 (safety bar and crotch
restraint must be used)
9- 12 months = Seat in slot 2, Footrest in slot 5 (safety bar and crotch
restraint must be used)
3 Years = Seat in slot 2, Footrest in slot 7 (safety bar and crotch
restraint must be used)
stage 2
6 Years = Seat in slot 3, Footrest in slot 10
stage 3
12 Years and over = The Footrest should be used as a seat and would
normally be positioned between slots 4 and 6
You can work out the number of the slot by counting downwards from the top of
the legs.

parts checklist
g 1g g 1h g 1i
Wooden brace Metal brace x 2 Allen Key
g 1j
g 1m
Crotch restraint
Cushion seat section Cushion back rest section
g 1k
g 1n
g 1l
Barrel nut x 6 Screws x 10
2
Please take a few minutes to read this user guide before attempting to assemble
your product. Unpack your product carefully onto a soft level surface, such as a
carpeted oor. Familiarise yourself with the parts by comparing them with the
parts check list. Do not discard any packaging until you are sure you have all the
parts shown in the parts check list.
Left and right legs
g 1a
Upper seat back rest
g 1b
Lower seat back rest
g 1c
g 1d
Safety bar
g 1e g 1f
Seat Foot rest

assembling the highchair for stage 1
3
g 2
g 3
Insert a barrel nut into the predrilled
holes at either end of the wooden brace,
using a at head screw driver to ensure
that the slot is horizontal. Then using
the Allen key and screws provided,
attach the wooden brace to the legs.
Please note: do not fully tighten any of
the screws yet.
Slide the smaller loop of the crotch
restraint over the metal brace that you
intend to use in the highest position.
Then using the screws provided,
attach both metal braces to the legs.

assembling the highchair for stage 1
g 4
Select the desired position and rmly
push the seat into the chair frame until
the front of the seat is level with the front
of the high chair. Please ensure that the
seat isn’t twisted by selecting slots of
a corresponding height and that the
rear of the seat extends past the legs
by at least 20mm.
Slip the seat cushion over the seat
ensuring that the crotch restraint slots
line up and both ends of the seat
are completely covered.
g 5
4

assembling the highchair for stage 1
g 6
Thread the end of the crotch restraint
though the seat and cushion from
underneath.
g 7
To t the safety bar, slide the safety bar
through the crotch restraint then insert
the safety bar into the slots at the top of
each leg, making sure the bar is curving
toward the front of the highchair.
5

assembling the highchair for stage 1
g 8
Insert the upper and lower back
rests into the appropriate slots at the
top of the legs. Insert a barrel nut into
each of the pre-drilled holes at either
end of the back rests. Using a at
headed screw driver ensure that the
barrel nuts are horizontal and
use the Allen key and screws
provided to attach both
of the back rests.
6
g 9
Select the desired position and rmly
push the foot rest into the chair frame
until the front of the foot rest is level
with the front of the high chair. Please
ensure that the foot rest isn’t twisted
by selecting slots of a corresponding
height. Once you are happy with the
position of the seat and foot rest please
tighten all screws, being careful not to
overtighten and damage the wood.

assembling the highchair for stage 1
7
g 10
Slip the seat back cushion over the
upper back rest and secure with the
touch fastener

assembling the highchair for stage 2 & 3
g 11
Insert a barrel nut into the predrilled
holes at either end of the wooden brace,
using a at head screw driver to ensure
that the slot is horizontal. Then using
the Allen key and screws provided,
attach the wooden brace and both
metal braces to the legs.
Please note: do not fully tighten any of
the screws yet.
8
g 12
If required, select the desired position
and rmly push the seat into the chair
frame until the front of the seat is level
with the front of the high chair. Please
ensure that the seat isn’t twisted by
selecting slots of a corresponding height
and that the rear of the seat extends
past the legs by at least 20mm.

assembling the highchair for stage 2 & 3
g 13
Insert the upper and lower back rests
into the appropriate slots at the top
of the legs. Insert a barrel nut into each
of the pre-drilled holes at either end
of the back rests. Using a at headed
screw driver ensure that the barrel nuts
are horizontal and
use the Allen key
and screws
provided to
attach both of
the back rests.
9
g 14
Select the desired position and
rmly push the foot rest into the chair
frame until the front of the foot rest is
level with the front of the high chair.
Please ensure that the foot rest isn’t
twisted by selecting slots of
a corresponding height. Once you are
happy with the position of the seat
and foot rest please tighten all screws,
being careful not to overtighten and
damage the wood.