Motive ES-2 User manual

Environmental Sensor (ES-)
Installation guide
Français se trouve au dos.

English

Scan this code or visit gomotive.com/es-install
for additional support, including step-by-step
instructions in multiple languages and tips about
mounting and cabling.
Table of contents
What’s in the box
Installation
Mounting
Activation
Understanding the LEDs
Replacing the batery
Troubleshooting
1
2
4
6
8
9
12
What's in the box
ES- Sensor
Alcohol wipe
Small mounting plate
screws (3)
Large mounting plate
screws (5)
Mounting plate
Device screws (5)*
Spare adhesive
Reset pin
ALCOHOL
*Use these screws to secure the device to the mounting plate
1

Installing using the Fleet App
(recommended)
1Install a Motive Asset Gateway using cable power so
that it can connect to the Environmental Sensor.
For Asset Gateway installation instructions, visit:
gomotive.com/ag-install
2Download and log in to the Motive Fleet App from
Google Play Store or Apple App Store.
3Go to the Devices tab.
4Follow the in-app instructions to guide you through
installing the Environmental Sensor.
1Install a Motive Asset Gateway using cable power so
that it can connect to the Environmental Sensor.
For Asset Gateway installation instructions, visit:
gomotive.com/ag-install
2Log in to the Motive Fleet Dashboard as an admin
or installer.
3Go to the Admin section and navigate to “Assets”.
4Visit gomotive.com/es-install to finish installing
your sensor.
23
Installing using the Fleet Dashboard

Mounting
Use the included alcohol wipe
to thoroughly clean the area
where you want to atach the
mounting plate.
If ataching the plate to a metal
surface, use the small mounting
plate screws; for wood surfaces,
use the large mounting
plate screws.
Atach the sensor to the
mount and secure it using the
device screws.
Remove the adhesive backing
from the mounting plate and afix
the plate to your desired location.
45

The LED will start blinking blue
to indicate that the sensor is
beginning the pairing process.
Please allow up to 10 minutes
for the sensor to pair with the
Asset Gateway.
Activation
Press the pinhole reset buton
on the side of the sensor by
inserting the reset pin.
Press the reset buton again. The
LED will turn solid blue to confirm a
connection to the Asset Gateway.
If not, wait a few more minutes
and try again.
You can now track your asset
and sensor telematics in the
Motive Fleet Dashboard.
New York
Liberty City
Office
Cinema
Broadway
Record Music
National Park
National Street Sesame Street
FILM
Music
tree
Suitcase
TEMPERATURE
20.0 F
HUMIDITY
40%
67

Flip the device over to reveal four
screws and use a T screwdriver
to remove them. The top and
botom parts of the device will
easily detach. Set the botom
housing aside.
Use your forefinger and thumb to
lightly grab the batery from the
batery holder. Pull the batery
out being careful not to use too
much force and damage the
metal springs.
Replacing the batery
Understanding the LEDs
LED will stay illuminated for a few seconds ater the
reset buton is pressed.
For more information, visit: gomotive.com/es-install
Solid blue
Device is working properly
Blinking blue
Pairing to an Asset Gateway
Blinking yellow
Connectivity to the Asset Gateway is weak
Blinking red
Paired Asset Gateway cannot be found
Blinking white
Firmware update in progress
Solid red
Low batery
89

Note
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment of and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit diferent from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment and RSS  RF exposure compliance requirements. This equipment should
be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body. This Transmiter must not be co-located or operating in conjunction with any
other antenna or transmiter. Changes or modifications not expressly approved by Motive
could void the user's authority to operate this equipment.
This device contains license-exempt transmiters / receivers that comply with Part 15 of
the FCC Rules and with Innovation, Science and Economic Development Canada’s
license-exempt RSS(s). Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment and RSS  RF exposure compliance requirements. This equipment should
be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body. This Transmiter must not be co-located or operating in conjunction with any
other antenna or transmiter. Changes or modifications not expressly approved by
KeepTruckin could void the user's authority to operate this equipment.
10 11

Troubleshooting 855-434-3564
[e-mail]
help.gomotive.com
Resources For multilingual step-by-step
instructions, scan the QR
code or visit:
gomotive.com/es-install
For Asset Gateway
installation instructions, scan
the QR code or visit:
gomotive.com/ag-install
Download the
Motive Fleet App
12