Moto XFB User manual

OWNER’S MANUAL
LPB2NM Rev 6.0 08/2023
XFB/XSF/SFL Low-Prof ile Bed

×1(2 for K/CK)
Mattress Retainer Bar
×1
Accessories Box
Hand
Control
ACCESSORIES BOX:
×6
Legs
×1
AC Power Cord
×1 ×1
Power Supply
Setup the power foundation without the bed frame.
1Open the box lid. 2Take out all the accessories from the packaging and put them aside. All
electronics and components that need to be installed are located in boxes
under the foundation or attached to the frame. Before discarding the packing
materials, ensure that all the parts are accounted for.
3Install 4 legs, make sure the
legs are tight.
HEADBOARD
HEADBOARD
5Install the remaining 2 legs on the foot end
of the bed, make sure the legs are tight.
HEADBOARD
DC
Power Cord
Hand Control
Connector
4Keep the bed folded. Flip over the
bed with the bottom box on and let
the bed stand on the 4 legs. Discard
the bottom box.
HEADBOARD

Remove the red plastic safety lock before
unfolding your power foundation.
6
Remove the red plastic
safety clip.
Red Plastic
Safety Clip
Remove the folding locking
pin by pulling upwards.
Locking Pin
Turn the locking pin 90° in
counter clockwise direction.
Locking Pin
WARNING!
FAILURE TO FOLLOW THIS STEP WILL RESULT IN DAMAGE TO YOUR POWER FOUNDATION.
PLEASE MAKE SURE YOU FOLLOW THE INSTRUCTIONS CAREFULLY BEFORE UNFOLDING YOUR POWER FOUNDATION.
8Install the mattress retainer
bar one side after another.
2
1
7Make the bed completely flat.
HEADBOARD

9Connect the hand control and secure it with the
connector lock.
Uncoil the AC power cord, connect the DC
power cord to the power supply and then
connect the power supply to the AC
power source.
DONE!
HEADBOARD
AC Power Cord
Power Supply
Hand ControlHand Control Connector
DC Power Cord

Setup the power foundation with the bed frame and slat base.
*NOTE: Optional parts are required.
1Take the bed out of the box, put it on the slat base,
do not install any legs. Keep the bed folded. 2Connect the hand control and secure it with the connector lock. Uncoil the AC power cord, connect the DC power cord to the
power supply and pull the AC power cord towards the direction of
the AC power source
through either the bottom or the side of the
bed frame.
HEADBOARD
AC
Power Cord
HEADBOARD
Hand
Control
AC
Power Cord Power Supply DC
Power Cord
Hand
Control connector

3
Turn over the bed. Install the middle stabilizer bracket
as shown.
(*Optional parts are required to perform this
setup. )
Metal Frame
Of The Bed
Slat Base
Screws
ST4.2×16
HEADBOARD
Remove the red plastic safety lock before
unfolding your power foundation.
4
Remove the red plastic
safety clip.
Red Plastic
Safety Clip
Remove the folding locking
pin by pulling upwards.
Locking Pin
Turn the locking pin 90° in
counter clockwise direction.
Locking Pin
WARNING!
FAILURE TO FOLLOW THIS STEP WILL RESULT IN DAMAGE TO YOUR POWER FOUNDATION.
PLEASE MAKE SURE YOU FOLLOW THE INSTRUCTIONS CAREFULLY BEFORE UNFOLDING YOUR POWER FOUNDATION.

HEADBOARD
5Make the bed completely flat
with a flipping motion . 6Install the mattress retainer bar one side after another.
HEADBOARD
2
1
7Connect the power supply to the AC power source.
AC Power Source
AC
Power Cord
HEADBOARD

HEAD BOARD
DONE!
8Lift the head of the bed by hand control. Install the two
stabilizer brackets as shown.
(*Optional parts are required to perform this setup. )
Hand Control Instructions
ADJUST
This button lifts the head section of the foundation.
This button lowers the head section of the foundation.
Lifts Head
Lowers Head
Screws
ST4.2×16
Washers
M8*16 Bolts

12
2
1
a)Align the slot hole of the headboard bracket to the sleeve into
which the leg threads. DO NOT OVERTIGHTEN. Too much force
may damage the thread.
b)The headboard bracket has 2 adjustable slots to accommodate
any frame type. Use the bolts and washers to secure the bracket.
Make sure the bolts are tight.
Headboard Bracket Installation Guide (Optional)
Headboard brackets are optional and not included. A 1/2” (13 mm)
socket and 1/2” (13 mm) wrench are required to complete the installation.
a)To put the T-Bracket and Headboard Bracket together, you will
need (2) M8×16 bolts and (2) nuts. Slip the bolts through the holes
from T-Bracket to Headboard Bracket with the head of bolt facing
outward. Use the 1/2” (13 mm) socket and 1/2” (13mm) wrench to
tighten the bolts.
You may now connect your headboard to the attachment plates using the remaining short bolts
and nuts to secure it to the brackets. The heads of the bolts will face outward. Use a 1/2” (13mm)
socket and 1/2” (13mm) wrench to tighten the bolts.
(2) Headboard Brackets (2) T-Brackets (8) M8*16 (4) Nuts (4) Washers
Parts List
INCLUDED WITH POWER FOUNDATION
(8) Screws
ST4.2×16
(6) Legs
(1)AC Power Cord
Stabilizer
Brackets
(2)
(1) Socket Wrench
(4)M8*16 Bolts (4)Washers
(1)Hand Control
9V 9V
(optional)
9V
Middle Stabilizer
Bracket
(1)
OPTIONAL EQUIPMENT/PART (NOT INCLUDED)

Lift the head and foot end of the bed by remote control. Install the spacing connector as shown.
Customer Service Toll Free: 1-844-696-6886 Email: [e-mail]
Install two spacing connectors to ensure the gap between the two
adjustable bases is consistent.
Spacing Connector for TXL/T/CKS (Optional)
(2) SPACING CONNECTOR (TXL/T/CKS ONLY)
Product Serial Number (Figure B)
Each power foundation has its
unique serial number. The serial
number can be found on the metal
frame near the legs at the foot
area.
Figure (A)
(B)
0 0 0 0 0 0 0 0 0 0 0 0
Spacing
Connector
Bed Frame
Bed Frame
0 0 0 0 0 0 0 0 0 0 0 0
(A)
(B)
PRODUCT PROTECTED BY FOLLOWING PATENT:
— US PATENT: 10, 306, 994
— US PATENT: 11, 013, 330