Moto XFB User manual

OWNER’S MANUAL
LPB14W4MSA Rev 3.0 08/2023
XFB/XSF/SFL Low-prof ile Bed
With Motion Sensor And Audio System

Setup the power foundation without the bed frame.
1Open the box lid. 2
Take out all the accessories from the packaging and put them aside. All electronics and components
that need to be installed are located in boxes under the foundation or attached to the frame. Before
discarding the packing materials, ensure that all the parts are accounted for.
×1(2 for K/CK)
Mattress Retainer Bar
×1
Accessories Box
Mounting
Bracket
×2 ×2
Motion
Sensor
ACCESSORIES BOX:
×1
AC
Power Cord
×1
Remote
Control
×1
Power Supply with Battery
Backup Box
9V 9V
9V
(Optional)
×3
AAA
Batteries
AAA
×1
Sync Cord
（TXL/T/CKS Only）
×6
Adjustable Legs
HEADBOARD

4Keep the bed folded. Flip over the
bed with the bottom box on and let
the bed stand on the 4 legs. Discard
the bottom box.
3Install 4 legs, make sure the
legs are tight. 5Install the remaining 2 legs on the foot
end of the bed, make sure the legs are tight.
Uncoil the DC power cord (connected to the
control box) and put it to the side of the bed.
Remove the red plastic safety lock before
unfolding your power foundation.
6
Remove the red plastic
safety clip.
Red Plastic
Safety Clip
Remove the folding locking
pin by pulling upwards.
Locking Pin
Turn the locking pin 90° in
counter clockwise direction.
Locking Pin
WARNING!
FAILURE TO FOLLOW THIS STEP WILL RESULT IN DAMAGE TO YOUR POWER FOUNDATION.
PLEASE MAKE SURE YOU FOLLOW THE INSTRUCTIONS CAREFULLY BEFORE UNFOLDING YOUR POWER FOUNDATION.
HEADBOARD
HEADBOARD
DC Power Cord
Control Box
HEADBOARD

Connect The Motion Sensor Connectors.
7Motion sensor installation = +
Motion
Sensor
Mounting
Bracket
Prepare The Motion Sensor Hardware.
STEP 1: Connect the motion
sensor to the mounting
bracket.
STEP 2: Rotate the
mounting bracket 90
degrees clockwise
STEP 3:
DONE !
STEP 2: Connect the motion sensor connectors as illustrated.
Note there are two connectors, one on each side of the bed.
STEP 1: Clip the mounting bracket onto the center adjustable legs as illustrated.
HEADBOARD

HEADBOARD
9one side after another.
Install the mattress retainer bar
10 Uncoil the AC power cord, connect the DC power cord to the
power supply and then connect the power supply
to the AC power source.
8Make the bed completely flat.
the remote control.
Insert the batteries into
AC Power Cord
AC Power Source
DC Power Cord
Power Supply
AAA AAA AAA
2
1
DONE!
HEADBOARD

Setup the power foundation with the bed frame and slat base.
1Take the bed out of the box, put it on the slat base, do not
install any
legs. Keep the bed folded.
2
Uncoil the DC power cord .
Remove the red plastic safety lock before
unfolding your power foundation.
3
Remove the red plastic
safety clip.
Red Plastic
Safety Clip
Remove the folding locking
pin by pulling upwards.
Locking Pin
Turn the locking pin 90° in
counter clockwise direction.
Locking Pin
WARNING!
FAILURE TO FOLLOW THIS STEP WILL RESULT IN DAMAGE TO YOUR POWER FOUNDATION.
PLEASE MAKE SURE YOU FOLLOW THE INSTRUCTIONS CAREFULLY BEFORE UNFOLDING YOUR POWER FOUNDATION.
HEADBOARD
Control Box
DC Power Cord
motion sensor
extension cord
HEADBOARD

4Motion sensor installation
STEP 1: Connect the motion sensor connectors as illustrated. STEP 2: Use the double sided tape to secure the motion
sensor when necessary.
HEADBOARD
Control Box
5Pull the DC power cord towards the direction of the AC power
source through either the bottom or the side of the bed frame.
Pull the two motion sensors to the two sides of the bed frame.
Make the bed completely flat
with a flipping motion .6Install the mattress retainer bar one side after another.
HEADBOARD
AC
Power Source
DC Power Cord
DC
Power Cord
HEADBOARD
2
1

DONE!
Insert the batteries into
the remote control.
7Uncoil the AC power cord, connect the DC power cord to the
power supply and then connect the power supply to the AC
power source.
HEADBOARD
AC Power Cord
AC Power Source
DC Power Cord
Power Supply
AAA AAA AAA

Electronics Quick Reference Guide
If simultaneous operation of two foundations is desired, please
follow the steps listed below.
Note the sync cord is needed to control two foundations with
mobile APP, follow the "Synchronizing Two Foundations with Sync
Cord" instruction to install the sync cord or follow the "Wireless
Syncing Instruction".
Head Motor
Foot Motor
Neck Motor Lumbar Motor
HD Motor FT Motor Neck Motor LB Motor
HD Massage FT Massage
LED
SYNC MOTION
USB
VOICE
CB20B
Control Box
USB
Charger
DC
Power Cord
Power Supply
Motion Sensor
AC
Power Cord
Foot Massage
(2 for King)
Head Massage
(2 for King)
LED
Audio
System
Sync Plug
Sync Plug
Control Box 1
Control Box 2
HD Motor FT Motor Neck Motor LB Motor
HD Massage FT Massage
LED
SYNC MOTION
USB
VOICE
HD Motor FT Motor Neck Motor LB Motor
HD Massage FT Massage
LED
SYNC MOTION
USB
VOICE
Sync Cord
Synchronizing Two Foundations with Sync Cord
STEP 1：Unplug foundations from the power source.
STEP 2：Connect the male ends of the sync cord to the female sync plugs of the control boxes
(Refer to below illustration).
STEP 3：Plug foundations back into the power source.
STEP 4：
Check to ensure all cords are securely attached.Either remote will operate both foundations
simultaneously.
Sync Cord
Remote Control
Press and hold and on both remotes at
the same time for 8 seconds,until the LCD
screen flashes and shows UNSYNC.
STEP 1：Make sure both remotes are individualy
paired to the foundation. If the remote is
not paired with the foundation, follow the
pairing instructions.
STEP 2：Make sure both foundations are at home
(flat position).
STEP 3：Press and hold and on both
remotes at the same time for 8 seconds
until the LCD screen shows SYNC.
Wireless Syncing Instruction
UN-SYNC Two Foundations
Press
and hold
Press
and hold

Pairing Remote
Setting Programmable Position
BATTERY LEVEL
Make sure the batteries are good. Replace them when
needed.
Plug the power cord back into the power source. The
LCD screen on the remote control shows “PASS”, and you will hear
an activation sound in 2 seconds indicating the remote is paired to the
power foundation.
Unplug the power cord from the power source. If 9V
backup batteries were installed in the power supply,
remove them.
Adjust the head and foot to your desired position.
To save a new position, repeat step 1 and 2 and the new position will
be saved.
Press and hold the LED button for about 5 seconds until the
screen shows SAVE, then press programmable buttons or ,
until you hear 2 beep sounds.
Press and hold Select buttons and until the
LCD screen of the remote control shows PAIR.
STEP 1：
STEP 2：
STEP 3：
STEP 1：
STEP 2：
STEP 3：
STEP 4：
The original remote that comes in the box is already paired to
the foundation. No further action is required. In the event when
the remote is not paired with the
foundation, follow the pairing
instructions below.
Remote Control Instructions
ADJUST
One-touch programmable positions.
SETTING PROGRAMMABLE POSITION
This button lifts the Head/Foot/Neck/
Lumbar section of the foundation.
This button lowers the Head/Foot/
Neck/Lumbar section of the foundation.
MASSAGE FEATURES
Turn on the head massage. Cycle
through 3 massage intensities.
Turn off the head/foot massage.
Turn on the foot massage. Cycle
through 3 massage intensities.
SELECT BUTTON
Press these two button to select
Head/Foot/Neck/Lumbar zone.
ONE TOUCH BUTTON
UNDER BED LIGHTING
One-touch ANTI-SNORE preset
position.
One-touch flat position.
One-touch TV preset position.
One-touch Zero Gravity preset
position.
Zero Gravity adjusts your
legs to a higher
level than your heart,
helping to relieve
pressure of the
lower back and promote circulation.
Under bed LED lighting on/off.
AAA AAA
AAA
The battery icon in the upper-right conner shows the battery level,
replace the batteries when the battery level is low.

Legs Installation Guide
Support leg may be needed on some slat/platform bed frames, refer
to the leg configuration table for height adjustment.
* Make sure the adjustable legs are properly tight, and the plastic caps have been placed at
the bottom of the legs. Incorrect installation might cause the part to fail or damage the floor.
Leg
Configuration
Leg Height
Leg Configuration Table
4 " 7⁵⁄8 " 11³⁄8 "
×6
Included in
Accessories Box
(See Page 2
for details)
Lift the head and foot end of the bed by remote control. Install four stabilizer
brackets as shown. Use a phillips screwdriver and socket wrench to tighten
the screws and bolts.
Headboard Bracket Installation Guide (Optional)
Headboard brackets are optional and not included. A 1/2” (13 mm)
socket and 1/2” (13 mm) wrench are required to complete the installation.
12
2
1
a)Align the slot hole of the headboard bracket to the sleeve into
which the leg threads. DO NOT OVERTIGHTEN. Too much force
may damage the thread.
b)The headboard bracket has 2 adjustable slots to accommodate
any frame type. Use the bolts and washers to secure the bracket.
Make sure the bolts are tight.
a)To put the T-Bracket and Headboard Bracket together, you will
need (2) M8×16 bolts and (2) nuts. Slip the bolts through the holes
from T-Bracket to Headboard Bracket with the head of bolt facing
outward. Use the 1/2” (13 mm) socket and 1/2” (13mm) wrench to
tighten the bolts.
You may now connect your headboard to the attachment plates using the remaining short bolts
and nuts to secure it to the brackets. The heads of the bolts will face outward. Use a 1/2” (13mm)
socket and 1/2” (13mm) wrench to tighten the bolts.
(2) Headboard Brackets (2) T-Brackets (8) M8*16 (4) Nuts (4) Washers
Stabilizer brackets are optional and not included. They can fix the
bed onto the slat base. A phillips screwdriver and socket wrench are
required to complete the installation.
(4) Stabilizer Brackets (1) Socket Wrench(8) Screws ST4.2×16 (8) Bolts M8*16 (8) Washers
STABILIZER BRACKETS COMPONENTS
OPTIONAL EQUIPMENT/PART (NOT INCLUDED)
Socket and Wrench 1/2'' (13mm)
HEAD BOARD
Screws
ST4.2×16
M8*16 Bolts
Washers

MotoSleep APP Home Screen
Open www.motosleep.com from your browser.
Scroll down to the bottom of the page and press download.
In the download page, tap the download button to download the app.
Open the download file and install the app.
MotoSleep Mobile APP (Optional)
Open APP Store on your IOS device
Tap the Magnify Glass Icon and search with the keyword
Tap on and to install the APP
Wait for the download/installation to be complete
GET
+INSTALL
Before you start. Switch on the pairing function on your mobile device. Make sure your
MotoSleep Power Foundation is correctly connected and is power-on.
The MotoSleep APP will automatically pair your MotoSleep Power Foundation once you start
the APP and does not require additional settings.
www.motosleep.com
REMOTECONTROL
REMOTECONTROL
HEAD FOOT
REMOTECONTROL
REMOTECONTROL
1
STOP
2
REMOTECONTROL
1 2
TV Z-G
SNORE
REMOTECONTROL
2
1
STOP
REMOTECONTROL
SNORE
TV Z-G
2
1
REMOTECONTROL
1
STOP
2
TV Z-G
SNORE
OWNER’S MANUAL
Four-button Remote Control Three-button Remote Control
Five-button Remote Control
Eleven-button Remote Control
Eleven-button Remote Control
Ten-button Remote Control
Ten-button Remote Control
Thirteen-button Remote Control
Thank you for purchasing a MotoSleep
Power Foundation.
* The effective connection range is ± 10m
General Information
Install the MotoSleep APP
IOS
Android
The Built-in Owner’s Manual at your fingertip
Device Pairing
9
8
6
7
5
4
3
2
1
List of MotoSleep Products within
the connection range*
Tap the Refresh Button to refresh
the MotoSleep Products List
Enter the Settings Page
Back to the Home Screen
10
Serial Number of the control box
Owner’s Manual Page
Troubleshooting
Disconnect from the paired
MotoSleep Product
Rename your MotoSleep Power
Foundation of your choice
Choose the light colors, and
set up the motion sensor timer
Home Screen
Settings Page
MotoSleep APP Remote Control
SELECT DEVICE
BED
Refresh
3
1
2
MotoSleep Mobile APP is a mobile application to control the MotoSleep Power Foundation with
mobile devices. The application is available for both iOS and Android based smart devices.
The MotoSleep Mobile APP uses the latest technology to communicate with your MotoSleep
Power Foundation. Make sure your mobile devices has the pairing function for the APP to
work correctly.
10
SETTINGS
DISCONNECT
MOOD LIGHT SETTING
Serial Number
5
4
6
OWNER’S MANUAL
8
TROUBLESHOOTING
9
RENAME
7
OWNER’S MANUAL
8
TROUBLESHOOTING
9
1
11
12
13
14
10
9
8
7
5
4
3
2
6
Enter the Settings Page
Select Head,Foot,Neck or Lumbar section
Select Head,Foot,Neck or Lumbar section
Lifting function
Lowering function
One touch flat position
Head Massage (3 different intensities)
Foot Massage (3 different intensities)
15 Massage Off Button
Programmable Position 1
Programmable Position 2
Under Bed Lighting
Anti-Snore Preset Position
TV Position
Zero Gravity Preset Position
Remote Control
* Remote interface varies in between different MotoSleep
Adjustable Base models. If you wish to disconnect from
the current paired Adjustable Base, Enter the Settings
Page and tap the Disconnect button.
BED
1
HOME
2
3
4
5 6
7 8 9
10 11 12
13 15 14

The volume is on minimum;
Audio System not paired properly;
Please contact the store or customer service.
Audio System
cannot be
paired
Restart your power base;
Do not attempt to pair the device behind a wall;
Make sure you’re pairing the device within the working
distance (26 ft).
No sound
Description
of problem Possible cause, correction & maintenance
Audio System
1. Once power is supplied, the audio kit begins to search pairing device
automatically. It keeps searching until it pairs with other device successfully.
It could only pair with one device at a time. If you want to pair with a different
device, disconnect the paired device, before connect with the new device.
2．The audio kit could be controlled via the paired device.
3．Description of device：REMO4.11
4．Connection rang: 26 ft.
Pairing Instruction
Frequently Asked Qustions
Install two spacing connectors to ensure the gap between the two
adjustable bases is consistent.
Spacing Connector for TXL/T/CKS (Optional)
(2) SPACING CONNECTOR (TXL/T/CKS ONLY)
Lift the head and foot end of the bed by remote control. Install the spacing
connector as shown.
Customer Service Toll Free: 1-844-696-6886 Email: [e-mail]
PRODUCT PROTECTED BY FOLLOWING PATENT:
— US PATENT: 10, 306, 994
— US PATENT: 11, 013, 330
Spacing
Connector
Bed Frame
Bed Frame
Product Serial Number (Figure B)
Each power foundation has its
unique serial number. The serial
number can be found on the metal
frame near the legs at the foot
area.
0 0 0 0 0 0 0 0 0 0 0 0
00 0 0 0 0 0 0 0 0 0 0
00 0 0 0 0 0 0 0 0 0 0
(A)
Figure (A)
(B)
(B)